I have 9" classic ipad. may i connect ipad to separate 21" monitor and use it as main monitor?
I have 9" classic ipad. may i connect ipad to separate 21" monitor and use it as main monitor?
The Apple Support Communities are an international user to user technical support forum. As a man from Mexico, Spanish is my native tongue. I do not speak English very well, however, I do write in English with the aid of the Mac OS X spelling and grammar checks. I also live in a culture perhaps very very different from your own. When offering advice in the ASC, my comments are not meant to be anything more than helpful and certainly not to be taken as insults.
You would need to find a 3rd party dispay extender app to accomplish this. The results may or may not be acceptable to you.
http://www.macworld.com/article/1156288/imac_second_monitor.html
Similar Messages
-
on my ipad it says ipad is disabled connect to itunes but i try and connect it to itunes and says i needvto wright the password in the ipad first but cant help please
I have the same problem with my ipod touch ... but im trying to find a way to fix it without restoring it...
but one fix is to shut it down completely ... then press and hold BOTH the power button and the home button .. hold both of those 4 ten seconds .. then release the power button but still hold down the home button .. and then it'll show something that says "connect to itunes" once u get it connected to itunes , click the restore button ... BEWARE THIS WILL WIPE OUT EVERYTHING ON YOUR IPOD!!! IT WILL RESTORE IT BACK TO FACTORY SETTINGS , AS IF U JUST BOUGHT IT !!!!! then it should work fine again .. but u will lose all data on there besides the things you have synced with itunes already..
Thats y im iffy with doing this , im trying to find a fix where i wont have 2 restore it but i dont think there is 1 :'(
good luck tho
~sam -
I have a wirless network. I connect all my computers to it and a printer. I can print wirelessly from all computers. I tried to add the printer to my new Macbook, which is connecte to the network, but can't find the printer on the add printer and scan icon on preferences. I downloaded a installation printer utility from the Manufacturer (lexmark), but it didn't work. Any sugestions?
Thanks,
IvetteYou would need to get the IP address of your printer then manually add a network print queue.
To get the IP address, on the control panel of your printer, press on Setup > Network Setup > TCP/IP > View/Set IP address. -
My iPad won't connect to my wifi anymore. Was using it and it just quit. It is not my wifi because my daughter's iPad works just fine. I've turned it off and back on, reset, forgot this connection and nothing works. Help???
1. Turn off router for 30 seconds and on again
2. Settings>General>Reset>Reset Network Settings -
Why has my ipad mini stopped connecting with my iPhone 4S? I used to use it to download books, or transfer emails to my ipad mini. It was fine 3 days ago, now I get a message saying " cannot join with iPhone" Any help greatly appreciated.
You can try resetting your iPad and iPhone by simultaneously pressing and holding the Home and Sleep/Wake buttons until you see the Apple Logo. This can take up to 15 seconds so be patient and don't release the buttons until the logo appears.
Try again to see if the problem persists. -
Trying to connect with my father on Facetime and all we get is connecting but never connect. Have updated the software, Trying to connect with my father on Facetime and all we get is connecting but never connect. Have updated the software
Hello trailblazer59,
The article linked below provides some useful troubleshooting steps that can help get FaceTime working on your iPhone.
iOS: Troubleshooting FaceTime
http://support.apple.com/kb/TS3367
Cheers,
Allen -
Hi! I am using Snow Leopard 10.6.8, iTunes 10.6.3 on my Intel i3 iMac and should I purchase the latest iPad, would I be able to set up, synch and use it without iCloud? Also, would iWork files be interchangeable between the two bevices? And...could information from the Mac be transferred into iBooksAuthor? Regards Neil
You may need to update iTunes to iTunes 11 but you can do that running Snow Leopard 10.6.8. I would recommend running iTunes 11 anyway. It is a bit different in the user interface, but it works the same that it did in 10.6.3.
You can transfer iWorks files back and forth without iCloud but you will need to use file sharing with iTunes. However, you will have to purchase the iPad versions of those apps becuse the Mac versions will not work on the iPad if you were thinking about using the Mac apps.
You can read about file sharing here
iWork for iOS: About iTunes File Sharing
Sorry, but I know nothing about iBooks Author. -
I am trying to set up home sharing between my iphone 4s and mac which is running itunes 11. Both are connected to my home wifi network and using the same apple id but on the iphone app it says 'Turn on Home sharing in iTunes on your computer or apple tv using account ***
Does anybody have suggestions as to why this is the case?Understanding Home Sharing - Support - Apple
Hope this helps. -
Can I hook my iphone 5 to a touchscreen monitor and use the touchscreen feature of the monitor. Would I have to use the lighting to hdmi?
The connection of the phone to the monitor would allow you to see, but does not have the ability to translate the touch on the monitor to the phone through that cable.
-
I use a macbook pro retina. I use a 32 in. monitor and use it full screen. I size the screen manually. Since i upgraded to maverick, I have to resize the screen each time I change windows.Before the upgrade the screen stayed where I put it.
Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, or by a peripheral device.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
*Note: If FileVault is enabled under OS X 10.7 or later, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test. -
Can I connect my iPhone to my Mac and use the Mac keyboard to write texts
Can I connect my iPhone to my Mac and use the Mac keyboard to write texts?
No.
You can connect a bluetooth keyboard to your iPhone to write texts. -
I have the l latest iMac with the Lion OS. Can it be used as a secondary monitor to a PC laptop? If so, how is this accomplished?
This is called Target Display mode, unfortunately this isn't possible with a current iMac unless the PC Laptop has a Thunderbolt outpout port which I'm certain it does not. Please read both Target Display Mode Mid 2011 iMacs & if you are interested Target Display Mode 2009 & 2010 iMacs.
-
My IPad is getting hard to charge,I have to wiggly the charger to get it to charge. I've bought a new charger and used difference outlets. I need to know what is wrong?
Consider where you are wriggling the charger (I suspect you mean the cable. Why does everybody refer to a cable as "the charger"?) and make sure all the contacts there are free from pocket fluff and such.
-
Connecting 2 (21.5" & 27") iMacs and using 21" as second display
Hi, I have 2 imacs (1x27 and 1x21.5), 27 is mid 2010 and 21.5 is late 2009.
Iam trying to find out if I can use 21 as 2nd display off the 27.
I connected them together with mini dv and they default to 21 as primary and 27 as 2nd.
Any help here would be greatly appreciated?
Thanks in advance.
PaulWelcome to Apple Support Communities
Of course not. Late 2009 and Mid 2010 21'5-inch iMacs can't be used for Target Display mode because they aren't compatible. See > http://support.apple.com/kb/PH11302
It means that you can't use your old 21'5-inch iMac as an external display wired, but you can use it wirelessly. To do it, you just need that both iMacs are connected to the same network and the app ScreenRecycler -
Ooops, guess I didn't need to post everything in the title - sorry! I bought the pages app - but couldn't save or print so with some online searching found that I had to uninstall the iWork trial which had expired. I did that - but now I can't figure out how to re-install the pages app!! The app store says it's installed, but I can't find it anywhere to open and use it. I'm not very computer savvy - and am a first time Mac user and am getting extremely frustrated! I e-mailed some help center and they can't seem to help me either. I would appreciate any help/advice that can fix my problem - thanks in advance!!
OK Apple has stuffed up the demo version upgrade process so the first thing you need to do is get rid of the demo.
That includes getting rid of the files in the system.
The instructions how to do that are here:
Note That where you see / that is the sequence of folders, each nested inside each other.
User/Library/Preferences the com.apple.iwork.Keynote.plist
Means the User (you, the little home icon, whatever you are called on your computer) then the Library folder inside that and then the Preferences folder inside that.
Lion initially hides the System folders from you so you have to go to the Finder > Menu > hold down the option key and click on GO > Library to see it.
Peter
Maybe you are looking for
-
After upgeade to win10 build 9926, my desktop application get wrong monitor count.
I have an application that needs to query monitor counts. I follow the below link : http://stackoverflow.com/questions/20261523/detect-number-of-display-monitor It query one DeviceID. That is right. But in yesterday, I upgrade my notebook to win10 bu
-
The new photo app and iBooks Author
I updated to Mac Os-x 10.1.3 and when opening iBook Author, in the media picker under photos the new photo app is missing to pick photos. Does anyone have a solution? or do I need to be patient for an update. Brgds, Jelger
-
How many NetInstall images needed?
Hello All, I am trying to figure out how many NetInstall images I need for my environment. So far I have read that for Leopard you can have one 32bit for PPC machines and one 64bit build for Intel machines, is this true? Or do I really need to make a
-
ICloud question related to my iPhone
How do I delete my iCloud account on my iPhone since I have to sign in and I don't know my password? They can't sent me my password since the email account for my old Apple ID is no longer valid. In the end I'm really just trying to get my iCloud ac
-
Windows 7 advisor says to download the latest driver for Broadcom 802.11b/g WLAN before I can upgrade from Winows XP. My notebook is a Compaq Mini 110c-1100CA. Please get me the latest driver. This question was solved. View Solution.