I have a 17" Macbook pro with flickering red and cyan(blue) lines across the screen. The issue disappears temporarily when I tap on the computer, and the problem does not occur when I use external display or try to screen capture the problem.

I purchased my Macbook (17") through a certified apple tecnition in August 2012, it was refurbished and the motherboard was completely replaced. I do a lot of photo editing, but I have been unable to do so because of the red vibrating lines that interrupt my screen. The issue disappears temporarily when I tap on the computer, and the problem does not occur when I use external display or try to screen capture the problem. I brought the computer back to the technition I purchased it from and he said that it was a problem with my fan, so I have two new fans but the issue is still occuring. He says he doesnt know whats wrong. Does anyone have any information on this issue?
Here is an image of the issue
http://www.flickr.com/photos/67839707@N08/8884847081/

I recommend having your Mac serviced by someone competent. A force sufficient to "blow apart" the fans was clearly excessive and may have damaged the display cable, as well as any number of other problems.
Dust is properly cleaned with a vacuum, preferably one designed for computer service, and they are not cheap.
Compressed air should never be used. It just blows dust everywhere, often into places where it can no longer be removed.

Similar Messages

  • When I enable imatch on my iPhone 4s it takes approximately 30 minutes before other data fills 13.2gb of usable data. This problem does not occur when I manually sync music to my phone. Is this a common bug, and if so; is there a fix?

    When I enable imatch on my iPhone 4s it takes approximately 30 minutes before other data fills 13.2gb of usable data on the phone. This problem does not occur when I manually sync music to my phone only when I access imatch. Is this a common bug, and if so; is there a fix?

    yes it is. you can sign out of itunes account then sign back in. use http://support.apple.com/kb/ht1311 to sign out.

  • MacBook Pro screen does not turn on after using external display?

    Hello,
    I am using a 15 inch MacBook pro from mid 2012. At work I connect it via mini-display port to an eternal monitor. Recently however, sometimes after I go home and try to turn the laptop back on, it turns on, but the screen does not. If I connect it to another external monitor, it uses that as the default display. Sometimes I can just restart the laptop and everything is fine, other times I have to turn it back on while holding the shift key in order for the laptops built in display to be used.
    After work, I unplug the mini-display port, and then power off the laptop.
    Can anyone help me understand why this may be happening so I can prevent it from happening again?
    Thank you.

    Try a smc reset:
    http://support.apple.com/kb/HT3964
    Also try a pram reset. Power off, power on holding the keys: Option, command,P,R(no commas) press the keys before thr start chime, then hold them till you hear the chime 2 times. Release and reboot.
    ATB

  • I have an Apple MacBook Pro with 2 USB ports and a MiniDisplay Port. I also have an HDTV with a HDMI port. How can I use the TV as a display without any tethering wires between my computer and the TV?

    I have an Apple MacBook Pro with 2 USB ports and a MiniDisplay Port. I also have an HDTV with a HDMI port. How can I use the TV as a display without any tethering wires between my computer and the TV? I have a MiniDisplay Port to VGA adapter, but there are two issues with it: The new display doesn't have a VGA port, and even if it did, I wouldn't want to have my mac constantly attached to the display by a cable. I was looking for a way to use the TV as a display without any wires. Is there some type of bluetooth setup I could use? Please let me know if you have any suggestions.

    As I wrote above, I think you should look into the Apple TV yourself. The best place to find information about what it can and can't do and to ask your own specific questions is probably in the Apple TV forum, here:
    https://discussions.apple.com/community/appletv/appletv

  • HT2499 I have a new MacBook Pro with OS X Lion 10.7.4. The DVD player does not have a feature to store film clips. Why? This is useful for my work and I had it on my older computer? Why the loss of capacity?

    I have a new MacBook Pro with OS X Lion 10.7.4. The DVD player does not have a feature to store film clips. Why? This is useful for my work and I had it on my older computer? Why the loss of capacity?

    I cannot recall the DVD player ever being a place to "store" videos - it is simply an app to play videos.
    If your machine is new, then iMovie should be included as the "shrunk" version of iLife is included with Lion (iMovie, Garageband, and iPhoto). However, iMovie is not a place to store videos either - it is a video editor. You import your clips and edit them in order to then burn to a DVD or share via a social media site.
    Have you considered simply dragging the clips to your folder "Movies"? That would be a great place to just store them (please be aware that videos are usually large files, so keep your hard drive space in mind so you keep a minimum free and available for the OS to operate properly):

  • I have a new MacBook Pro with iPhoto installed.  I edit photos, mainly photo orientation via rotating, but when I go back to run a slideshow the changes weren't saved and the photo is back to vertical...please help...thanks

    I have a new MacBook Pro with Iphoto installed when purchased.  When editing a photo, primarily orientation changes, the slideshow initially displays the photos in proper orientation.  However, after leaving Iphoto and shutting down the computer, and then going back to run a slideshow the photo displays back to its' original orientation, that is, the edit-change was not saved.  Please help...the program information says all edit-changes are automatically save and therefore there is no save command, but my changes are not being saved...thank you for any suggestions...HM

    what version of iPhoto and of the OS?
    Back up your iPhoto library, Depress and hold the option (alt) and command keys and launch iPhoto - rebuild your iPhoto library database
    LN

  • I have a newer MacBook Pro with an AMD processor.  It is my understanding that Parallels can only be used on Mac's with Intel Processors.  Is that true and if so does anyone have recommendations about how to have a windows side to my Mac

    I have a newer MacBook Pro with an AMD processor.  It is my understanding that Parallels can only be used on Mac's with Intel Processors.  Is that true and if so does anyone have recommendations about how to have a windows side to my Mac

    Then it either is a pirate clone or you are misinformed.
    Apple Computer has never used AMD processors in its products.
    However, the Graphics Processing Unit (GPU) is a Radeon unit, which is an AMD subsidiary. Parallels, VMWare, VirtualBox will all work fine with the Intel Core i7 or i5 CPU that powers the Mac, and use the AMD Radeon GPU that drives the displays.

  • I have a 2009 Macbook Pro with 1T hdd 8GB Ram and ran Maverick without problem...Yosemite installation has me completely frozen, nothing works but the spinning ball...I had to force shutdown last night, and haven't turned it on again...what do you ad

    I have a 2009 Macbook Pro with 1T hdd 8GB Ram and ran Maverick without problem...Yosemite installation has me completely frozen, nothing works but the spinning ball...I had to force shutdown last night, and haven't turned it on again...what do you advise?  During installation emptied cache, etc. Backed up using time machine, fortunately.

    Try these in order testing your system after each to see if it's back to normal:
    1. a. Resetting your Mac's PRAM and NVRAM
        b. Intel-based Macs: Resetting the System Management Controller (SMC)
    2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
    4. Reinstall Yosemite: Reboot from the Recovery HD. Select Reinstall OS X from the Utilities menu, and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible
                because it is three times faster than wireless.
    5. Reinstall Yosemite from Scratch:
    Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
    How to Clean Install OS X Yosemite
    Note: You will need an active Internet connection. I suggest using Ethernet if possible
                because it is three times faster than wireless.

  • I have an older Macbook pro with a dvi output and I want to watch movies on my tv. I have a dvi to hdmi cable but the only image I get on my TV is my desktop background. None of my movie players with appear on the TV screen. What am I doing wrong?

    I have an older Macbook pro with a dvi output and I want to watch movies on my tv. I have a dvi to hdmi cable but the only image I get on my TV is my desktop background. None of my movie players with appear on the TV screen. What am I doing wrong?

    Hi Maryan,
    Open System Preferences > Displays > select the window for you external monitor > click on the Arrangement tab and check the box next to Mirror Displays. It may be slightly different in Lion, but the idea is the same.

  • I have a 2009 macbook pro with os x10.9.2 and can't find drivers for windows

    i have a 2009 macbook pro with os x10.9.2 and can't find drivers for windows. i trying to install windows using bootcamp but does not allows me to download the drivers..

    From the system requirements page: http://support.apple.com/kb/HT5634 for your computer
    MacBook Pro
    (13-inch, Mid 2009)
    4
    4
    DVD
    DVD
    DVD
    MacBook Pro
    (15-inch, 2.53 GHz, Mid 2009)
    4
    4
    DVD
    DVD
    DVD
    MacBook Pro
    (15-inch, Mid 2009)
    4
    4
    DVD
    DVD
    DVD
    MacBook Pro
    (17-inch, Mid 2009)
    4
    4
    DVD
    DVD
    DVD
    MacBook Pro
    (17-inch, Early 2009)
    4
    4
    DVD
    DVD
    DVD
    The drivers are located on the OS DVD that came with your computer.

  • I have a 15" MacBook Pro with Mountain Lion installed.  I have partitioned the hard drive into two partitions.  Is it possible to install Snow Leopard on the second partition?  If so how do I do it?

    I have a 15" MacBook Pro with Mountain Lion installed.  I have partitioned the hard drive into two partitions.  Is it possible to install Snow Leopard on the second partition?  If so how do I do it?

    If your MacBook Pro had Snow Leopard on it at one time then sure. (Early 2011 or earlier)
    How to erase and install Snow Leopard 10.6
    Obviously choose the second partition to install into. It has to be OS X Extended journaled formatted in Disk Utility (BootCamp software makes it a MSDOS/FAT32 formatted partition if you used that to partition with)
    If it's a Early 2011 or Late 2011 that came with 10.7, it's possible, but it's not easy.
    https://discussions.apple.com/thread/3264421?start=0&tstart=0
    If you can't install Snow Leopard, there is a thread over at MacRumors how to run Snow Leopard in a virtual machine program under 10.7 or 10.8

  • I have a new MacBook Pro with OS10.8.2 and cannot get Contacts to print a list of addresses with pictures showing.  There is a check box selecting "picture" which has been checked - but no picture.  This worked fine on OS10.7.5.  Problem??

    I have a new MacBook Pro with OS10.8.2 and cannot get Contacts to print a list of addresses with pictures showing.  There is a check box selecting "picture" which has been checked - but no picture.  This worked fine on OS10.7.5.  Problem??

    First, back up all data immediately, as your boot drive might be failing.
    There are a few other possible causes of generalized slow performance that you can rule out easily.
    Reset the System Management Controller.
    If you have many image or video files on the Desktop with preview icons, move them to another folder.
    If applicable, uncheck all boxes in the iCloud preference pane.
    Disconnect all non-essential wired peripherals and remove aftermarket expansion cards, if any.
    Check your keychains in Keychain Access for excessively duplicated items.
    If you have more than one user account, you must be logged in as an administrator to carry out this step.
    Launch the Console application in the same way you launched Activity Monitor. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
    View ▹ Show Log List
    from the menu bar.
    Select the 50 or so most recent entries in the log. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V). You're looking for entries at the end of the log, not at the beginning.
    When posting a log extract, be selective. Don't post more than is requested.
    Please do not indiscriminately dump thousands of lines from the log into this discussion.
    Important: Some personal information, such as your name, may appear in the log. Anonymize before posting. That should be easy to do if your extract is not too long.

  • Hello, this might be a basic question, but how do you open QuickTime to record a new webinar? I have a new MacBook Pro with Yosemite and can only get QuickTime to appear in Finder but not actually open to allow me to record something new. Thx.

    Hello, this might be a basic question, but how do you open QuickTime to record a new webinar? I have a new MacBook Pro with Yosemite and can only get QuickTime to appear in Finder but not actually open to allow me to record something new. Thx.

    Hi Winterwilly,
    Welcome to Apple Support Communities. 
    The article linked below answers your question of how to use QuickTime to record something on your MacBook Pro’s screen.
    QuickTime Player 10.x: Record your computer’s screen
    Cheers,
    -Jason

  • Dear Sirs, I have a apple macbook pro with mointain lion OS 10.8.4 with mail 6.5 and I cannot open the .eml attachments, what can I do to solve this?

    Dear Sirs, I have a apple macbook pro with mointain lion OS 10.8.4 with mail 6.5 and I cannot open the .eml attachments, what can I do to solve this?

    drag the file to the desktop, then using the menu item "File > Get Info…"
    in the "Open With" section select "Mail" from the list and then click the "Change All…" button to make Mail the default application for all .eml files

  • I have recently purchased MacBook Pro with Mac OSX 10.7.3 Lion and I would like to install Final Cut Pro 6 Studio2, and it came up with this error: 'you can't open application FinalCutProStudio.mpkg because PowerPc apps are no longer supported..pls advise

    I have recently purchased MacBook Pro with Mac OSX 10.7.3 Lion and I would like to install Final Cut Pro 6 Studio2, and it came up with this error: 'you can't open application FinalCutProStudio.mpkg because PowerPc apps are no longer supported......Is there a way to run FCP6 on lion withoput this error? Any help would be appreciated.....

    Hi Shane,
    Just one more quesiton re: this topic, I am looking to get rosetta but do not have Leopard or Snow Leopard...
    I read that it is not on Snow Leopard only on Leopard....so do I need to get only Leopard? Can u advise?
    Alternatively I do have Mac OS X Tiger so is it on this and can I install it from here?
    Please excuse my lack of knowledge here, just trying to get my FCP 6 up and running asap....
    Best Rgds.

Maybe you are looking for