I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use?
I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use? Essentially having two wifi connection off the same network? If so how do I set this up?
Extending using a wireless connection always results in a performance compromise.
If the Express is going to extend using a wireless connection, then the Express will need to be located about half way between the AirPort Extreme and the general area where you need more wireless coverage. The more that you have line-of-sight between the Extreme and Express, the better the network will operate.
Remember......the Express can only "extend" the quality and signal speed that it receives, so it needs to be located where it can get a very good signal from the Extreme. Although Apple cleverly uses the term "extend", a more accurate term for the Express would be "repeater".
If the Express will extend by connecting to the Extreme using a permanent, wired Ethernet cable connection......highly recommended for best performance.....then the Express can be located exactly where you need more wireless coverage. There is no signal loss at all through the Ethernet cable, so the Express gets a full speed signal no matter where it might be located.
Post back to let us know which way to you want to go.
Similar Messages
-
I have an airport extreme base station. Experiencing large signal loss in a particular room. Will an airport express, placed in that room, restore the signal? Thanks, Glenn.
The Express can only "extend" the bandwidth of the wireless signal that it receives.
So, you would not want to place the Express in the same room where you need more signal, you would want to locate the Express approximately half way between the AirPort Extreme and the area that needs more wireless coverage. -
I just purchased a ipad 2 and have not sync it yet. I have an old pc and would like to move the itunes library account to a newer pc that I have. Can I move the library to the ipad and sync ipods to the ipad and/or move the library to the new pc?
Perhaps this web page will help: http://support.apple.com/kb/ht1229
But I must point out that leaving the iPhoto Library on the external is worth considering. Your internal drive would be better off without having to carry the photos.
When you booted with the external connected and you were asked for the library, did you try navigating to the Library in on the external drive? -
I am using an older AirPort Extreme as my base station and I want to extend the range by using a recently purchased AirPort Express. When I try to find either device using the AirPort Utilities function on either my new IPad 4 or my older MacBook Pro neither device is detected. However the utility is seeing that we are connected to the Internet which is through the Extreme. What am I doing wrong?
For now, leave the AirPort Express powered off.
Power off the entire network....all devices.....in any order that you want
Wait a few minutes
Power up the modem first, and let it run 2-3 minutes by itself
Power up the AirPort Extreme next, and let it run a full minute
Keep powering up devices one at a time about a minute apart until everything is powered up (leave the Express off for now)
Open AirPort Utility and check to see if the AirPort Extreme is visible.
If it's not, click the AirPort Utility menu at the upper left of the screen, then click About AirPort Utility. Post back with the version number of AirPort Utility that you see there....which should be AirPort Utility 5.6.1.
Post back on your progress. -
I upgraded to OS Yosemite on my MacBook Air...and I cannot upgrade the Adobe Flash download that Adobe keeps asking me to download. I get the screen and when I click on the icon it just creates a new window but not download. Thoughts?
I just tried the link and it is just fine. If the GateKeeper pops up then open Security & Privacy preferences, click on the General tab, set the last radio button to Anywhere.
-
Is my AirPort Extreme (802.11n) Base Station defective?
I'm trying to set up a wireless network with my new AirPort Extreme (802.11n) Base Station. I dismanteld my existing network that consisted of an old model AirPort Extreme and an AirPort Express. I can't seem to get anything to work properly with the new hardware. I have a G4 Quicksilver that uses an AirPort card. Is that the issue? I thought they were compatible. I was not able to update the Setup Utility because I don't have an Intel Mac. Still, that shouldn't prevent me from doing an initial setup. I'm thinking perhaps the unit is defective. I've been working on this several hours a day for almost a week. This is the most trouble (by far) that I've ever had with any Apple product. I'm really disappointed. I suspect the hardware is defective, but based on all of the issues I've read about in this forum, I think it could just be reflective of the poor overall quality of the new AirPort Extreme. What a let down.
What is the exact name of the application you are using to configure the airport?
You should be using "AirPort Utility"
It is a Universal application, so it should work on both a PPC and Intel mac.
As for the update, if you can't download it via software update, you most likely do not need it.
The quicksilver only has an Airport card:
http://support.apple.com/specs/powermac/PowerMac_G4_Quicksilver2002.html
That means that you will need to configure the airport extreme N to operate in the 2.4 GHz range. You will need to tell it that it needs to be compatible with 802.11b
There is probably an option for 802.11 b/g/n compatibility.
Are you going to still use your airport express? you could either use WDS to extend your wireless network without connecting the two airport base stations with an ethernet cable... or you could connect them together with an ethernet cable and configure the same network name and use two different channels (only use 1, 6, or 11). If you extend a network, they both need to use the same channel.
If the quicksilver is the only machine on your network, it will not be any faster.
Actually, you could make things faster, now that I think about it... I am guessing that your quicksilver is not located near your airport extreme. If I am wrong, just ignore this...
You could use one of your airports as your main base station, connected to your cable modem/dsl whatever... then you connect the other airports ethernet to your quicksilver. you then turn off the airport card in your quicksilver and set up the airport connected to your computer to use WDS and connect to the other airport using 802.11g.
You now have gone from an 11 mbps max (5 mbps real world) connection to a real world 30-40 mbps link.
Other options would be to look for 802.11g or 802.11n usb adapters for the quicksilver... I am not sure what is mac compatible out there, since it is probably a small market since it is built in to all new macs.
Good luck -
Airport Extreme Dual-Band Base Station Is excessively slow
Let me start off by stating this is my first apple support discussion and I have no experience in these forums but rather forums elsewhere.
My Airport Extreme Dual-Band Base Station is completely updated as of DEC. 30, 2012 running version 7.6.1 and I have the latest airport utility, so bare in mind some of the previous fixes I've Read seem unavailable to my setup
Our household has 7-13 of the following devices connected in a 24 hour average:
5-6 iPhones all running iOS 6 (1, iphone 3gs; 2-3, iPhone 4; 2, iPhone 5)
1 iPad 2 wifi only running iOS 6
2 MacBook Pro 13" early 2012 models one running mountain lion and the other running lion
1 mac mini early 2011 model running mountain lion server and is connected outside the network as a public server
1 Apple TV latest model(1080p) latest updates
1 LG 47" 1080p 3D TV
3 blueray players
2 Windows 7 PC one a laptop and the other a desktop
1 HP All-In-One Printer
1 AT&T MyCell Antenna
My problem is as follows:
My network is running rather sluggish. the base station is getting at the very minimum good signal strength to all my devices most of them getting great signal, so I doubt it be the result of range. I've tried messing with the channels and radio settings but have yet to find a correct optimal settings. I've tried searching around these forums as well as in other areas and have not found a suitable solution. my apple TV lags and jitters a lot. I have trouble airplay to it because of what I've read elsewhere which is latency issues. I have no clue how to test latency. I have realized that it isn't a matter of noise in the area because noise doesn't pass 15% and signal is optimal in all areas. of where the devices are. I've noticed connecting my server directly gives me 47Mb/s as compared to the Ethernet connection of 32Mb/s so I am clueless as to a solution. I know that with my old router the wifi speeds were outstanding but that router kept disconnecting wifi clients and then reconnecting them. sadly this is happening again with the apple router. last night my iPad would not stay connected and our network had so much lag that I couldn't even load the youtube app let alone a video. also buffering takes an odd amount of time sometimes 3 minutes. for a 30 second video on youtube. I have no guest network active and I have a wpa2/wpa personal encryption set on the network. I could use some serious help. the people of my household have no problem returning the apple router but I think to urge otherwise. if I could get some help in a solution that would be fantastic.
Thanks in Advance,
Blaine MillerCan you tell us whether your "modem" is a simple device with only one ethernet port or is it a "gateway", which is a combination modem/router with 3-4 ethernet ports?
-
Airport Extreme 802.11n Base Station blocking RealPlayer 11 completely
I am trying to play this radio station (just a brasillian sports channel) on RealPlayer 11:
rtsp://real.rbsonline.com.br/liverbs/*/broadcast/rdgaucha/gaucha.rm
Which is completely blocked on my Airport Extreme 802.11n Base Station with the latest firmware update.
It even blocks when RealPlayer is configured for HTTP only.
I am using it on my iMac which is connected directly via a ethernet cable instead of wifi to the Airport Extreme 802.11n Base Station.
RealPlayer can play it fine when I plug my iMac directly to the cable modem so it proves is the router. I never had RealPlayer issues before when I was using a linksys router.
It does really feel like Apple put an intentional block on RealPlayer to stop competition.
Anyone seen this issue? Guess it is related with the BBC RealPlayer issue.Fixed myself, problem was because I setup OpenDNS on base station, removed it now works
-
So basically I would like to know if its best to have them setup on "join a wireless network" or "extend a wireless network"
Obviously the one I use to extend the network is setup that way, the other 2 are set on "join a network"
is this the optimal configuration? or should I have them all on "extend a wireless network" ?There is really no "best" setting here for the AirPort Express devices. If you need more wireless coverage in the area where an Express is located, then it makes sense to configure the Express to "extend" a wireless network.
If you already have good coverage in an area where an Express is located, then the "join" configuration makes sense.
I've yet to meet the first user who felt that he/she had too much wireless signal coverage in their home, but you never know. -
Airport Extreme 802.11g base station loses internet connection often
I just installed an Airport Extreme base station (802.11g version Apple Base Station V5.7) last week. And it keeps dropping my internet connection at least once a day.
I simply replaced an old SMC Barricade wireless router that died (and was a POS). But I only had to reset the SMC about once every 2 months. Nothing else has changed in my setup. Only the router/base station is different.
The wireless part is fine. Even when the internet connection gets dropped the hard wired AND wireless clients can still access the local network. Reseting the DSL modem has no effect. The only solution is to power cycle (unplug and plug back in) the AEBS OR restart it from Airport Admin utility.
But you can't do that from offsite. When the AEBS drops the internet connection I can't access my office network from home!
Is there a place in Airport Admin Utility which tells you the status of your internet connection like most generic wireless routers with web-based software do?
Any ideas on resolving this?
Thanks"Any ideas on resolving this?"
Looter,
Based on your description, open AirPort Admin Utility and check the configuration of your main base station on the "Internet" pane. If you're using ethernet cable from the modem to the base station, the top selector [Connect Using:] should show "Ethernet" and the second selector [Configure:] should show "Using DHCP"
Also, check your iMac's System Preferences>Network at "Show: AirPort" and check the PPPoE pane which should show no entries (unless your isp requires its use), and the TCP/IP pane which should show "Configure IPv4:" as being "Using DHCP" - while all other info is filled in automatically.
"Is there a place in Airport Admin Utility which tells you the status of your internet connection like most generic wireless routers with web-based software do?"
No, the AirPort Admin Utility is not web-based, only located on your computer with the information available to it necessary to operate the AirPort system. It does not actually administer the signal. I think that is done only by System Preferences>Network.
"I'm actually referring to the Airport Express base station not my MacBook Pro's wireless connection. Is there anywhere in the Airport Admin Utility software that tells you the status of the AEBS' internet connection NOT the wireless connection."
No, that info is not available in that utility. The information you seek is at System Preferences>Network, but only after the system scans for it. Click the "Assist me..." button and then, on the "Do you need assistance setting up a new network connection or solving a network problem?" panel that opens, click the "Diagnostics..." button. A "Network Diagnostics" panel will then open and if its scan shows there is no internet the lights to the left of "Internet" and "Server" will be yellow instead of green. Meanwhile, it continues scanning for the connection until it is re-established. I determined this by pulling my cable from the phone jack, later reinserting it.
Further information that may be helpful to you can undoubtedly be found in threads such as this other one:
http://discussions.apple.com/thread.jspa?threadID=884049&tstart=0
edit-
In re-reading, I may not have given you what you need. It sounds as if you may be "timing out" somehow on your connection. You might want to check around at some of your log-on settings to see if there is that possibility connected to one of them, even though the only thing I can think of is the "Renew DHCP Lease" button which is unknown to me, as I've never used it.
Message was edited by: myhighway -
Airport Extreme as rempte base station with Netgear DG834N as Main Station
Does anyone know if it is possible to set up an Airport Extreme base station as a remote base station with a Netgear DG834N as its main base station. i.e. the Netgear is connected to the internet and I want to set up my AP as a remote unit to extend the wireless connectivity.
That is not possible. The Netgear device is not compatible with Apple's WDS.
-
Airport Extrem Base Station Connection problems
Just purchased the airport extreme base station to replace my old router, but when I plug it all in the airport utility can't find it!
A new Extreme creates an open wireless network that you must select. It appears in your Wi-Fi menu like this (except the words will read AirPort Extreme...):
Select it. AirPort Utility will load and walk you through its configuration.
applenovice1 wrote:
Unfortunately they say this is NOT covered by the technical support anf want to charge me £35 to talk to them!!!
https://www.apple.com/uk/support/complimentary/
They have never asked me to pay. Are you certain that you phoned Apple and not someone you found through Google? There are plenty of scam outfits that appear first in a search engine. Use the links I provided. -
Hi..I have an AirPort Extreme base connected to my DSL Modem and has been working fine. But I recently bought another DSL modem along with the latest Airport Express. With this one however I can't get it to connect to the Internet. The light on the Express is flashing green though. Does it mean I have to re-set the settings on Airport Utility? I.e. the old settings haven't been cleared yet. Any suggestions?
Let's see if I can get this straight.
You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
Correct?
See this Apple document:
http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
The wireless unit on the right of the diagram can be either of the newer Apple base stations.
Extreme, Express, Time Capsule -
i have an airport extreme attached to cable, then one airport express to extend the range. when i try to add an additional airport express to extend range in another area of house, can't get it to work. utility says it has found a new base station and asks if i want to use it. if i click yes, then the old setup is disabled.
Ok, thanks for clarifying which models you have. Please see the following Apple Support article on how to configure these older base stations for a Wireless Distribution System (WDS).
-
I have gifted an airport extreme to a neighbor and I assumed she would be able to connect and "create a new network" with a new password on her iPhone. That didn't happen. It keeps asking for my password. What next? Thanks!
Have them perform a complete power recycle of their networking hardware. Please check out the following AirPort User Tip for details. Also, make sure that they perform a "factory default" reset on the AirPort (as described in the tip) to be sure to return the AirPort back to its "out-of-th-box" configuration.
Maybe you are looking for
-
Connecting a Sony BDV-N790 W to a Samsung Smart TV Model UN40D6050TF
Just a few days ago I bought the Sony DVD/Receiver/surround sytem at best buy. I I also bought a new HDMI cable to connect it to my TV. I truly believe I followed everu step in setting the dvd player and surround up. (Though I'm human) The dvd player
-
Problem installing snow leopard drivers on windows 7 including sound
Hi, I installed windows 7 but then when I inserted the snow leopard dvd to install the boot camp drivers, it doesn't work. When I open it I get two options: either choose Remot Install Mac OS X or CD and DVD Sharing. So this is effecting everything.
-
Creation of standby logical controlfile
can anybody let me know how to create standby logical controlfile.... i know how to create physical standby control file.... when i created a logical standby controlfile and after mounting the logical standby database, i got an erorr database name is
-
New Tag in iTunes Store, Just Noticed? Any Help?
I just logged in to my iTunes Store account. And at the top right, near where your username is displayed, there was a new tag right next to it, in pale yellow that says "3 Videos". What is that?? Never seen it before? here's a link to the screencaptu
-
Opening .toast files causes my MAC to become unresponsive
Hi, My Macbook Pro (17-inch, Mid 2010 - 2.66 GHz Intel Core i7 - 8 GB 1067 MHz DDR3 - NVIDIA GeForce GT 330M 512 MB - Mac OS X Lion 10.7.2 (11C74)) has recently developed an extremely frustrating problem, it occurs whenever I try to open a .toast f