I have an airport extreme. i am trying to connect a laptop with windows 7 to a wireless printer, with no luck. any ideas?

The problem is not the router.. the issue is the vpn has put your computer in a different IP range with a different gateway. When you turn off the vpn the computer returns to local lan and can print.
Some vpn software allows you to set gateway to use local net instead of remote gateway or access to other webistes or local lan.
Read up the issue.
http://stevejenkins.com/blog/2010/01/using-the-local-default-gateway-with-a-wind ows-vpn-connection/
Cisco vpn client..
https://supportforums.cisco.com/thread/239113
I did not search much.. just grabbed the first article I could find that explains the issue.
The whole point of the vpn is whilst it is connected your computer is NOT part of the Local Lan .. it is part of the Remote LAN via the vpn tunnel.
It is also a security risk using split tunnelling so often it will not be allowed.
Plug the printer directly into the computer via usb or whatever.. Local connection will work.. not local lan.

Similar Messages

HT201077 For some reason, photos taken on my iPhone did not transfer to my iPad. Apple could not help I have now loaded the photos from my Phone to my laptop, but still cannot transfer them to the iPad. Any ideas please?

For some reason, photos taken on my iPhone did not transfer to my iPad. Apple could not help. So I have now loaded the photos from my iPhone onto my laptop, but still cannot transfer them to the iPad. Any ideas please?

I just had this problem as well and spent quite a bit of time reviewing all of the suggestions/ideas/comments, and since I am not that tech-savy I remembered this "suggestion" from the UK show The "IT Crowd" which was "Have you tried turning it off and on again??" (both devices)
http://bit.ly/18qL7OA (apologies for short ad on the youtube clip)
It worked!!

I have an airport extreme and am trying to extend the range of the wireless network with an airport express. I set it up with the help of apple support, both lights are green on both airports, but the range didn't change. What could be wrong?

I am trying to extend the range of my wireless network by adding an airport express to an airport extreme. I configured it with the help of apple support, but it hasn't changed the range that I can access the internet wirelessly in my house. What could be the problem? Does weather affect the wireless network??

So, on the Extreme you checked the box to "allow this network to be extened" ?
Correct?
And on the Express, you set it up to "Extend a wireless network" ?
Correct?
See this Apple article and see if you missed anything...
http://support.apple.com/kb/HT4145
To learn about other options for expanding your Wi-Fi base station wireless network and things you should consider before expanding your network, click here.
Set up: Components of an extended network
➊ Primary Wi-Fi base station (this is the base station connected directly to the Internet)
➋ Extended base station
Configuring a wireless extended network
To create a wireless extended network, you must place any extended Wi-Fi base stations within range of the primary Wi-Fi base station.
Start with the device that will be configured as the primary Wi-Fi base station. Then configure your extended Wi-Fi base stations, ensuring that each is within direct range of the primary Wi-Fi base station.The physical location of extended Wi-Fi base stations will vary according to the building environment and may require some experimentation.
If you have configured your Wi-Fi base stations in the past, it may be helpful to do a factory default reset of each Wi-Fi base station that will be part of the wireless extended network before you begin.

I have an airport extreme i am trying to add to an existing netowrk as an access point not as a router, any help is appreciated as i don't know much about networking.

At my work we have a modem and router to network 8 different pc's- all hard wired. My boss wants me to add an airport extreme so that he can get wireless connection on mobile devices. when i plug in the airport it creates a new network and i need to be able to connect to the existing network and not have the routers compete. is there a way to make the airport an access point instead? maybe by adding it to the exisiting router instead of one of the workstations?

When you introduced the AirPort Extreme, you had a condition where you have two routers in series. The simpliest solution is to reconfigure the downstream router (in this case the Extreme) as a bridge. This will allow the upstream router to provide the required NAT & DHCP services to all network clients regardless of which router they are connected to.
To reconfigure the Extreme as a bridge, you will use the AirPort Utility. (Note: I will provide the steps for using AirPort Utility v5.x)
AirPort Utility > Select the AirPort > Manual Setup
Internet > Internet Connection tab > Connection Sharing = Off (Bridge Mode)

I bought a airport-extreme but the software to program only works on Windows 7 to get it to work. Any work around?

I bought an Airport-Extreme but the software to program it only works on Windows 7 and above and I have an XP? Any work around?

Have you tried AirPort Utility 5.5.3 for Windows
You need to have XP SP3 installed on your PC to run this version of AirPort Utility.

I have just recently lost use of 2 USB ports and my isight camera. I have an isight G5 imac that has been working great. I have rebooted, reloaded my OS, and tried PRAM reset. I can use my keyboard, but not other peripherals. Any ideas on diagnostics?

I have just recently lost use of 2 USB ports and my isight camera. My keyboard works fine, but there is not any indication of connections when probing USB in "About this MAC". I have rebooted, executed a PRAM reset, and reloaded my OS, but to no avail I am out 2 of my 3 USB ports. I don't know how to diagnose the issue. Any ideas?
--kevinfromflagstaff

Well, if you've tried different USB cords and devices and have reset your PRAM:
http://support.apple.com/kb/HT1379
And SMC:
http://support.apple.com/kb/HT3964
I'd say your USB ports are shot - since they are an integral part of the logic board, replacing it will most likely be expensive. I'd still go for a definitive diagnosis at the Genius Bar.

Windows XP Home & Wireless printing with Airport

I have a PC running Windows XP Home, a macBook connected wirelessly through an Airport Extreme and an HP Photosmart C3180 all-in-one printer. The printer is plugged (usb) into the airport extreme. The macBook prints wirelessly to the HP just fine. What I cannot get is the Windows PC to utilize the HP printer. The PC is a desk top and is not wireless. Am I trying to do something that is not possible? Does the HP printer need to be directly connected to the PC for it to work?

Are you trying to print without an Airport (Extreme or Express) Base Station? You won't be able to print without the specific equipment.
As far as trying to get the XP side of your MacBook to work, have you installed the latest Boot Camp available? The drivers for Boot Camp have been updated recently. Hope this helps!
Hello iFelix;
I desperatly need yor help.I just bought Macbook Mac
OS 10.4 and I installed WIndows XP SP2,Every thing is
working very fine except wireless network and
bluetooth. Bluetooth is not issue but wireless
yes.Network driver is working ok and Atheros Network
wireless Adapter is working properly.I use Linksys as
arouter. But somehow wireless network does not take
the signals.When use Macintosh side, there is no
problem and it is not asking any password, wireless
working just fine.I dont know what to do. I hope this
information would be helpful to solve the problem.PLS
HELP ME. THANK YOU.
Mac OS X (10.4.7)
15 Al PowerBook G4 Mac OS X (10.4.7)

HT4199 trying to connect my MacBook Air to my existing wireless printer

I am trying to connect my newly purchased MacBook Air to my existing wireless printer, a Canon MP560. When I go to printer preferences and try to "add" a printer I'm not allowed to type anything at all in that window. What am I doing wrong? Thanks!

Does the printer appear in the window so you can select it?
Try resetting the printing system.
Reset Printing System
WiFi Printer to WiFi Network - Connect
Network Printer Troubleshooting

I have an airport extreme for my main internet connection, an express to listen to music on my home theatre, another express to extend the network upstairs, and one more express for my wireless printer. whats the best way to setup the express stations?

So basically I would like to know if its best to have them setup on "join a wireless network" or "extend a wireless network"
Obviously the one I use to extend the network is setup that way, the other 2 are set on "join a network"
is this the optimal configuration? or should I have them all on "extend a wireless network" ?

There is really no "best" setting here for the AirPort Express devices. If you need more wireless coverage in the area where an Express is located, then it makes sense to configure the Express to "extend" a wireless network.
If you already have good coverage in an area where an Express is located, then the "join" configuration makes sense.
I've yet to meet the first user who felt that he/she had too much wireless signal coverage in their home, but you never know.

I am trying to connect Dashboard shared variables to a server on a different subnet. Any ideas?

My goal is to control a device that is connected to our wired network using an Android tablet via Dashboard. I have created a vi with shared variables that controls the device as expected when it runs on a computer that is connected to the same wired network. The problem is that my Android tablet running the Dashboard app cannot connect to the shared variables on the PC running the vi on the wired network.
Our wireless network is on a separate subnet from our wired network. I am able to ping my Android tablet from the PC on the wired network but when I try to connect a variable in Dashboard, the PC running the SVE cannot be found. I tried listing it in the alternative server settings window and it still did not work. The only way I have been able to get around this is to run the vi which launches the server on a laptop that is connected to the wireless network and the wired network at the same time. My tablet can then find the server and my VI can connect to the instrument that is connected to the wired network. The laptop is somehow acting as a bridge between the subnets. I need to find a way for the Dashboard app to connect directly to the PC on the wired network. My PC IP address is 192.168.0.105. My Android IP address is 192.168.10.93.

Data Dashboard doesn't care about subnets, but it has to be able to access the server using the right ports. There is probably a firewall blocking the shared variable ports. This document explains how to configure a firewall to allow shared variables to be accessed. Your challenge will probably be to figure out where the firewall is and how to configure it.
It is also possible that the router that your Android device is connected to doesn't know how to route to the other network. Again, that is an issue with your router that you need to resolve.

Hi I have an airport extreme base station And trying to dial on windows

Ok I have a airport extreme base station the one with dial-up modem and power over ethernet. Well i have people PC as my provider, and can dial the connection on my macbook by using internet connect. but on my hp i can not. I have tried to create a connection type on it and cant figure out how to have it connect like on internet connect. tho i can go the admin utility and click automatically connect and click OK and it dials the connection to disconnect i re click it and click OK and it disconnects but i do not like it that way. So what am i to do and is their a internet connect app for windows. I have also contacted apple and hp and that did not help. Feedback welcome and is needed.
Thanks to all that leave feedback

If you are using dial-up.
Jon Sevy has a Java Utility for this purpose.
You will need Java in order to run the utility
http://www.java.com

Trying to connect our exercise bike to our wireless network. It sees the network, but once pass phrase is put in, it won't connect. Any suggestions? We have an Airport Extreme.

I am trying to connect our exercise bike to our wireless network. It sees the network, but once pass phrase is put in, it won't connect. Their tech support said the problem is with the router and we may need to open ports 80, 443 and 4348. We have an AirPort Extreme and I scanned for open ports and found 80 already open but the others are not. Tried using Port Mapping, putting the port number 443 in both the Public UDP and TCP fields and the Private UDP and TCP fields also. The Private IP address defaulted to 10.0.1.201 which is right outside of the DHCP range. Will this be the IP of the bike or should I change it to something else? Are the values I put in the fields totally wrong? Bike is still not connecting. Thanks for any help!

Here's an update:
Now the light is not blinking. It's a solid, consistant green. I don't know if it helps to narrow it down or anything, but I just figured I'd mention it.

Trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?

I am trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?
The Apple update Firmware for my Airport Extreme Base Station does not update for some reason? Help?
Additionally, I have an older version Airport Express that does not update with the newer Airport Utility Version 6.3 and asks me to download 5.6 to update? Is this worth it?
Thanks

The netgear is not going to work very well.. and not at all unless it is universal wireless extender.. you cannot use WDS method.
If it does support universal wireless then make sure the airport uses a rational SMB compatible wireless name.. not an apple name which is 35 characters long with spaces and illegal characters like apostrophe.
So nice AE name.. AEwifi and actually while you are trying.. fruitlessly to do this.. use AE24ghz and AE5ghz (so different names on the different bands)
Assuming your AE is gen3 or greater.
You should also fix the wireless channel at least for 2.4ghz since the netgear is probably only going to repeat 2.4ghz so use channel 11, as a trial.
And use no wireless security as a test.. if that works.. then use WPA1 & 2.. as often old equipment using WPA2 is not compatible.
If it fails with simple name.. fixed channel and no security. Sorry it is not compatible at all.. it happens.
If your AE is G wireless or earlier model.. really the time has come for replacement.
If your Express is G wireless model it is not supported.. and is too old to bother with expect I guess if you want to run audio to a speaker.
You must use older 5.6 utility to do this.. so do you have a computer running older OS.. up to Mountain Lion it is easy to install with a bit of manipulation.. later is much harder .. or windows computer anywhere or available to you.

How can I connect airport extremes using a wired-switch connection and have roaming capability?

My goal is to have 2 airport extremes and 1 timecapule connected via an ethernet switch so that I can enable roaming. I have no problems connecting them wirelessly where I create the wireless network on a primary airport wireless then add the others "extending" the network. However, if I attempt to do the same thing with a wired connection everything stops working (no connections from any airport). Here's the topology I'm trying to achieve. I believe my problem relates to the switch and the fact that I am serving up DHCP from a separate server. Is there a way I can achieve this (or similar) type of configuration? Thanks in advance.
BTW, I have read the various documents on the roaming network topology but none seem to be a match to this.

To answer your question, yes, if I _only_ have the main "create wireless network" airport connected/wired to the switch, everything works correctly.
OK, got that.
Also, if I have each of the 3 airports/timecapsule "create wireless network" using the same ssid name and passwd/protocol, everything works correctly (but of course, no roaming under this scenario
Sorry, you have me confused on this one. When the AirPorts are all configured to "create a wireless network", use the same SSID, security and password, and all AirPorts are in Bridge Mode........that is the exact definition of a "roaming" network.
Not sure what you mean when you say "no roaming" in this configuration.
Also, if I have the main "create wireless network" configured and have the 2 other airports "extend the network" and _not_ have them connected via the ethernet cable, everything works correctly (wireless airport interconnection)
That is correct.
However, if I plug the 2 other "extend the network" airports into the switch via ethernet, all connectivity shuts down.
This is not a correct setup. The "extend" setting on the AirPort assumes that they will connect using wireless. If you then try to connect an Ethernet cable to an AirPort that is expecting a wireless connection, that will result in a big feedback loop and effectively crash the network.

I have installed Airport Extreme on my iMac, but want to extend the wireless network with Airport Express. Everything is fine until I try to select Extend the wireless network. I select Extend Wireless network but have no success. Ideas?

I have installed Airport Extreme on my iMac, but want to extend the wireless to rooms with a weak signal. The internet connection is fine with the basic setup. As soon as I go into Airport Utility to select Extend Wireless Network and fill in what I believe is proper information, I get an error message that Airport Extreme no longer has an IP address, the internet connection is broken, and under Wireless, that there is a wireless network in existence that can't be found. Rebooting the modem only brings the Airport Extreme back to the starting gate so that the internet is once again available. I assumed (naively) that with the All Mac All-the-Time context, adding Airport Express would truly be Plug and Play. I got the plug, but no play. I asked a Comcast technical specialist about it and he said that I needed to reset the Airport Express settings back to their default, factory status. I looked that process up online and found out that the way to do that was to hold down the reset button, then plug Airport Express into the socket and wait for the green light to flash four times. Then wait 45 seconds and the default settings will return. I did all that, only to find out that after the initial flash of green, green never appeared again. I got a fast flashing yellow light, followed by the light going off. Apparently this didn't reset it properly. So, after hours trying to get this system to work, I appeal to someone who can see through this mess and provide the key to success!
highFly376

Let's see if I can get this straight.
You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
Correct?
See this Apple document:
http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
The wireless unit on the right of the diagram can be either of the newer Apple base stations.
Extreme, Express, Time Capsule

I have an airport extreme. i am trying to connect a laptop with windows 7 to a wireless printer, with no luck. any ideas?

Similar Messages

Maybe you are looking for