I have bought the wireless keyboard for my iPad. I was working for a day but now the power light won't stay on and as such won't connect to the iPad. I have changed the batteries but still no difference.
I have bought the wireless keyboard for my iPad. I was working for a day but now the power light won't stay on and as such won't connect to the iPad. I have changed the batteries but still no difference.
Not knowing which wireless keyboard you bought, it is difficult to be specific. but ...
it is quite normal for the keyboard's power light not to stay on - it is a way of conserving battery power.
Try this:
turn you keyboard off
on your iPad go to Settings > Bluetooth
if your keyboard is listed under Devices, then touch the little blue i to its right and choose Forget this Device
now reset your iPad: hold both the Home and Power buttons down for about 10 seconds until the Apple logo appears, let go promptly when the Apple logo appears and wait another 30 seconds for your iPad to turn itself on
After your iPad is back on again go back to Settings > Bluetooth
now turn your keyboard back on and see if it appeard under Now Discoverable
if it doesn't read your keyboard guide to figure out how to put it into Discovery mode
touch the listing for your keyboard under Now Discoverable, it should now appear under Devices
touch the listing for you keyboard under Devices, and choose to pair with it.
Similar Messages
-
I bought an iphone 3gs on o2 which was working fine till i restored it (which put ios5 on to it) now it wont activate, it keeps saying on itunes no sim inserted and on the iphone it has searching then says no service! Any ideas what i can do as cant get any further!
Some SIM cards were affected by iOS updates. Either contact O2 to get a replacement SIM or pop into a local phone shop and pick up a replacement SIM.
Once you have your new SIM, O2 have a swap my SIM page on their web site here:
http://swapmysim.o2.co.uk/
Follow the instructions on the O2 page and you should be up and running.
O2 do say it can take up to 24 hrs for SIM to be active, but I found it usually only takes half an hour or so before the new SIM is active.
Hope this helps. -
When I purchae my iPad, my user ID was set up as my email address, now I am not working for the company and my user ID is not working. I need to change my iPad user ID
You could go to settings/itunes & app store, tap on the ID and then log out. Tap on create new ID and do that and then log in with that ID. You would need to turn off imessage and facetime and turn them back on and activate them with the new ID. You will need to delete the icloud account save any contents to the device and create a new account. Remember that all purchases are linked to the old ID and can only be updated etc with that ID
-
RE: iPad Air and Apple Wireless Keyboard
HI, I have an iPad Air paired with an Apple Wireless Keyboard. Can I access emoji from the wireless keyboard?
Thanks for any help on this subject!Eureka! I kept searching and found the solution. So, if anyone wants to know here is the solution: press fn and the up arrow on F Keys (top) row (it's the one all way to the right. The iPad keyboard will then pop up on the iPad and from there you can access the emoji keyboard.
-
I have an Apple wireless keyboard synced to my iPad 2. Can sync this same keyboard be used with my iPad 3? If so, what are the syncing instructions?
Assuming you are talking about the aluminium keyboard the answer is yes. I had some problems trying to get my iPad 2/keyboard combo to 'forget' their connection but one complete the keyboard connected to my iPad 3.
-
I have just updated my ipad to 7.0.2 but now when I want to watch a download on BBC IPLAYER when I am off line it will not play the download.
I can only watch the download when I am on line . The funny thing is I can watch it then if I turn off my modem untill I shut down my i pad . Before the update I didnt need to be conected to watch my down load . Can any one help please ?Here you are "the strange draft logos"...
-
Have a 802.11n time capsule, the range of the wireless network has shrunk down to nothing over last few days. Used to be able to use wireless network anywhere in house, but now can only use in my office. Will not connect to iphones, ipad, itouch, or notebook. Worked fine last week, but over weekend just started having issues.
It is very possible that you may have some form of Wi-Fi interference that has appeared recently that is preventing your Time Capsule (TC) from providing a clean RF signal.
I suggest you perform a simple site survey, using utilities like iStumbler, or AirRadar to determine potential areas of interference, and then, try to either eliminate or significantly reduce them where possible. Look for other Wi-Fis that may be operating nearby. Note those with the strongest signals and which channels they are operating on ... then change the channel used by the TC to be at least 3-5 channels away. -
I have a 27" thunderbolt display NOT the iMac, and I'm trying to connect my xbox 360 to it via the Belkin AV360. I plug everything in and it does not work? I check all the power cables and and connections and still not he issue. Iv'e tried C-F2 also. has anyone used this devive (AV360) on there own 27" thunderbolt display (not the imac) and gotten it to work? If so I'd appreciate the help.
There are multiple reasons that lead to issue. You should read the troubleshooting guide to get the right solution to solve the issue: iPhone, iPad, or iPod touch not recognized in iTunes for Windows - Apple Support
-
I have a jetpack, and when I try to "connect" to my ipad or phone, it keeps telling me I am not using the correct password. I have tried everything. I even changed the password, nothing is working. Both are 4G, my ipad is an Air and my phone is a Iphone 5. I can get connected to other wifi on these features but not with my jetpack. Please help, I need to use this feature soon. Thank you so much
Chances are you mis-typed a character in the Wifi password and the devices saved that information. Now whenever you try to connect the device refers to the wrong password and the Jetpack does not accept your connection. Tell your devices to forget the wireless connection and start over.
Once you enter the proper WiFi credentials the Jetpack will allow you to connect. -
I currently have a DROID RAZR M and I'm 1 year into my 2 year contract. Since the Kitkat update, the phone won't stay charged and it's very buggy. I know this is not Verizons fault but it's also not mine. I would like to change my phone to an iPhone 5s and keep my same plan but switch to the Edge program. Is this possible? I don't think I should have to pay an early termination fee or anything like that since my phone has become almost unusable. I know under normal circumstances you have to wait 2 yrs to upgrade but due to the update and the poor service I'm now getting I hope Verizon can make an exception. Thank you.
How recently did you switch? If it's less than 60 days, then Verizon simply reinstates your previous account. The fact that you were on the EDGE plan and mailed the devices back, and they apparently are somewhere in the system, could cause complications, and it might just work out that you just go back on the same plan and they set you up with the same devices. I'm not sure how it will go - but since you are still being billed for the devices...
-
I have an apogee ensemble that I am using with Logic that was working fine 2 days ago but now it is seeing the apogee but giving me a conflict era and I can't get sound through my mixing board. What could be causing it, I haven't changed any settings
OK, but in my ipad, the apple id i have in itues is already the one iwant to have, but th one i used to sin in for i-coud is the other one. Any tip as to how to change the apple id for icloud and any idea how to know what apps i bought with the other apple id so as to delete them from my ipad to avoid being asked to enter another apple id every time they get updated? thanks!
-
Hi Guys! I have an Imac with Mac OS X version 10.5.8 and bought a wireless keyboard. Unfortunately I can´t use the volume buttons on the keyboard. I have checked almost everything, does anyone have any good idea?
Hello, try kguy's solution here...
https://discussions.apple.com/thread/2332457?start=0&tstart=0
First, Go to System Preferences, keyboard, and click on the Keyboard tab
Make sure that the checkbox by "Use all F1, F2, etc, keys as standard function keys" is NOT checked.
Next, click on the Show All button, and select Bluetooth. You should see your Apple Wireless Keyboard listed on the left side of the screen.
Click once to select it, and then click the gear icon at the bottom of the box, and choose Disconnect.
Power off the keyboard by holding down the power button on the keyboard for a few seconds until it show "keyboard Off on your imac screen, then turn it back on again.
The device should appear once again in your bluetooth list.
Try out the volume control buttons now, and see if that cleared things up -
i have 2 apple ids and one is from years ago when icloud wasnt a thought but now somehow it became my primary apple id and i cant photo stream with the apple id i use. Even if im signed into my old one the photo stream doesnt automatically go to my mac. Im not exactly technology savy but id love to figure this out.
I have also noticed the same "problem". I do not fully understand the impact of using the same ID on multiple computers and devices if I want to keep them all in sync.
-
Since purchasing the Note 3 in October i have had nothing but issues. I went through all the steps and eventually I was sent a different phone, which was working for the most part until the recent upgrade. Now I am back to the old issues, no service, it actually says not moblie network available, when everyone else in my family has coverage and are on my plan with iphones. I am missing text messages and dropping calls left and right. This is unacceptable for the cost of this phone and my service. I have did a hard reset etc. What else can I do??
Use the trackpad to scroll, thats what it was designed for. The scroll bars automatically disappear when not being used and will appear if you scroll up or down using the trackpad.
This is a user-to-user forum and most people will post on here if they have problems. You very rarely get people posting to say there update went smooth. The fact is the vast majority of Mountain Lion users will not be experiencing any major problems with the OS, or maybe with apps which are not compatible, but thats hardly Apple's fault if developers don't update their apps. -
I have my FireFox browser set to delete all the history when I close the window. It was working for a very long time and has recently stopped with no changes to the settings. This has happened once before and I deleted FireFox and re-downloaded it, that solved the problem for a short period of time but the issue has come up again. How can I fix this?
Can you check your configuration again? Maybe something went pear-shaped somewhere. It's located in Tools | Options | Privacy and then click the Settings button (see screenshot).
Maybe you are looking for
-
How to define the Java Resource Name with Consolidator API
Hi everybody, I want to create a JavaResource with the OracleLite Consolidator API. There is a method ConsolidatorManager.createJavaResource(jarName, className, replace) which provides this, but it does not allow to explicitelly set the object name f
-
Can you import shows from DVDs???
I just got a new video ipod and instead of spending money on shows from the music store can I import shows from DVDs???
-
I had to uninstall CS6 and I am trying to reinstall I have problems
I had to uninstall CS6 and I am trying to reinstall. The software wants a serial number and when I enter the original ID the suftware says it is wrong. What do I need to do? This all happened as I trialled Creative Cloud. The community said to uninst
-
Affine transformation with vector data
I want to use the SDO_UTIL.AFFINETRANSFORMS method to transform vector data in a sql statement. The example in the Spatial Developer's Guide is working so far. But if I change the SCALING parameter to TRUE I got a exception: Fehler beim Start in Zeil
-
Hi, I am looking to develop a strategy on how someone can use OWB to do data export/import from/into Oracle EBS. (assumming repository already setup in OWB). Any suggestions?