I have iphone 4 and i used it for a one and half years.i used it in sri lanka and doha qatar,recently i update it i.o.s 7, then it was working.after i.o.s 7.0.3 came i again updeted it and now my phone network is not working.now phone is locked.pls help.
i have iphone 4 and i used it for a one and half years.i used it in sri lanka and doha qatar also..,recently i update it i.o.s 7, then it was working.after i.o.s 7.0.3 came i again updeted it and now my phone network is not working.now phone is locked.pls help.
I am seeing if I can get another battery even though I do not believe that is the issue. It keeps giving me vdd_under which I believe is under voltage, maybe it is just a faulty battery? It charges up like normal and functions normal (when plugged in, or above 90%) but it gives under voltage warnings and shuts down when in heavy use (using camera or going back and forth to imessage). When just sitting idle it doesn't seem to turn off until that 55-60% mark. It may just be a faulty battery because I feel I installed all of the other cables correctly when replacing the screen, and I don't think those connections should affect the battery anyway except for maybe the logic board cable (the 2nd cable to be unplugged after the battery cable) I guess I could clean that out as well with isopropyl just in case.
Any other suggestions would be helpful... and I will get back to you if a new battery helps. Thanks!
Similar Messages
-
So my airport extreme recently had some nat/dns issue and in the airport utility displayed a warning about it and to correct it. I wasn't sure what to do so i pressed the resolve icon and now my guest network is not working.
Anytime you change networking hardware, it is always a good idea to perform a complete power recycle of your networking components.
I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results. -
After Hard Reset My Social Network is not working....
Due to Some problem I did Hard Reset to my C7 but now My Social network is not working.
I had reinstall the nokia software but still its not working properly.
In the Social network all the graphics are coming like picture with a cross.Something is wrong because a hard reset will never leave the TC with green LED.
What version TC.. what firmware??
What OS on the computer? -
We have purchased 5 apple minis and would like them all on one account, that way we can monitor the use of these units. They will be used strickly for a business application. Can I use one account in itunes or must i have multiple.
Not going to happen the way you want it to.
When you add a gift card balance to the Apple ID, it's available for the Apple ID.
Probably best to create unique Apple ID's for each... this will also make things easier in the future as purchases are eternally tied to the Apple ID they were purchased with. -
I have iPhone 6, 8.3. I cannot use bluetooth at all from my device, even to connect my macbook pro. I did all the recommended trouble shooting such as reboot and reset network settings. but it does not recognise any bluetooth device. Pls help.Thank you.
See iPhone BT profile on what can be connected/paired:
iOS: Supported Bluetooth profiles - Apple Support
And BT troubleshooting:
iOS: Troubleshooting Bluetooth connections - Apple Support -
Was setting up my ipad, turned it off. Came back turned it on and after you select ur country step it came up with "connect to itunes" logo, how do i fix this? And i dont have a computer.?!
Reboot the computer then try placing the iPod in Recovery mode and then restoring via iTunes.
Next try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings -
My iphone 6 connects to the car via bluetooth, the music works good, but the phone calls does not work. It looks like it is working but doesn't. I have tried in my Hyundai Sonata and a Dodge Dart rent car and get the same results. I updated the last 8.0.2. It worked the first day i had the phone, and then i updated to Ios 8.0.2 and it quit working.
Now when i get in the car, it acts like it is connected and makes the same call it was on after syncing to bluetooth, but it really isn't on a call. This is happening on both cars.
Does anyone know if this is the phone and i need to take it to Apple or if there is an issue that Apple is working on getting a fix for?
My son in law has the exact same phone as me, we both got the on 10/6, he had a Dodge Dart and his is working via bluetooth.
Someone HELP please, as i consider this a safety issue by not having my calls go to bluetooth.We had the same problem, but figure out the solution.
You MUST have at least 1 song added to your ITUNE! After you add a free song, then everything else should work as normal!
Hope this helps! -
Hello, it's been 5 days now since my imessage has not working..and i have chatted to the costumer for two times. I took thier advice and instructions just to enable to send and receive on it but unfortunately until now its still NOT working. Is there anybody who could help me please?
Try this even if you have already. Just make sure to follow the steps specifically.
Go to settings > Facetime > send and recieve > tap on your apple id and sign out. If your not signed in then that will work as well.
Go to settings > Messages > sent and recieve > tap on your apple id and sign out.
Restart the iPad by doing the slide to power off setup. Just hold the power button on the top right till it turns off.
After the iPad has been restarted:
Go to settings > Facetime > and sign in
Go to settings > Messages > and sign in
Wait about 3 min then restart the iPad again. Same instructions as above.
When you restart you should be able to use messages again. If not then call support again and talk to someone higher than the first level support they have. -
I tried to sync music from iTunes to my iPhone and when I click on "on this phone" the songs are there, but they are greyed out and have a circle in front of them. I can not click on those songs, delete or anything and when I eject the phone they are not on the phone. I tried to re-add the songs and it says it can't add songs because they've already been added. So HOW can I get the songs to actually ADD to my phone to where I can listen to them? It's like they're stuck in Sync limbo or something! Any help would be greatly appreciated.
I am having the same problem. I have just tried this. Unplug iphone > open itunes > delete all music from itunes library > close itunes > re-open itunes > add music from original folder > plug in iphone > select songs > press sync > unplug iphone using eject button onscreen > checked phone .... still nothing in music folder on phone. On itunes the "On this iphone" tab the songs remain there but greyed out.
-
i plugged in my ipod and now i get the error message: Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled" - i have a MAcBook pro and now my USB ports do not work - can anyone help me ???
Sometimes you have to reset the SMC two or three times for it to work, don't know why. I've seen that error message before and 100% of the time it was fixed with an SMC reset. I suppose it's possible that your keyboard or mouse IS drawing too much power, do you have access to another you could try?
-
Hi my keyboard is not working I took off the bottom case to change it prior my keyboard was fine and after just the power key worked. I checked everything no portions were bent and it plugged in good. I tried to turn it on this morning and now the power key doors not work??
Back up all data.
Triple-click anywhere in the line below to select it:
pmset -g assertions
Copy the selected text to the Clipboard (command-C).
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V).
Post any lines of output that appear below what you entered — the text, please, not a screenshot. -
My cellular network is not working on my iphone 5 after updating to ios 8.1.2 !! It was working fine on ios 8.1.1
my phone was not jillbreak or hacked to unlock. i need help, what can I do?Did you do the Reset Network Settings as I described above?
There is no way to go back. You can try reseating your nanoSIM or replacing it. Or call your cell provider and have them check the provisioning on your phone.
Or Restore your iPhone from your backup in iTunes. -
My cellular network is not working on my iphone 5 after updating to ios 8.1.2 !!
It was working fine on ios 8.1.1 i need help, what can I do?I have this problem too - and it is on a BRAND new iPhone 6 - I have definitively tracked the issue to the moment I upgraded to iOS 8.1.2 - and am beyond frustrated. No fix to tell you about, sorry…but you can read my post here if you are into the whole "misery loves company" thing: iOS 8.1.2 Cellular data problem (Definitive - maybe)
-
I have used Firefox for the last number of years but now it crashes upon opening.
I have used Firefox for the last number of years but now it crashes upon opening. I have unistalled and installed (version 6) but still it crashes. It does not start in safe mode either. I have read the various help support but I seem to be going around in circles. I am not a computer geek so please bear with me. Thank you.
Create a new profile exclusively for the 4.0 beta version and create a desktop shortcut with -P "profile" appended to the target to launch that profile.
* http://kb.mozillazine.org/Testing_pre-release_versions
* http://kb.mozillazine.org/Creating_a_new_Firefox_profile_on_Windows
* http://kb.mozillazine.org/Shortcut_to_a_specific_profile
* http://kb.mozillazine.org/Using_multiple_profiles_-_Firefox -
Wi-Fi to your iPhone does not work with the knowledge that I have worked Restart for the same purpose network does not work What is the solution please help as soon as
Okay, the Wi-Fi doesn't work. Turn it on.
Beyond that, we cannot offer any other assistance as you've failed to provide useful details of the problem.
When responding, post in your native language as your English makes very little sense.
Maybe you are looking for
-
How to get the field's type in the database with jdbc?
How to get the one filed's type(varchar,int,long...etc) with jdbc?? Can u help me?? It's best that giving a sample code..
-
Set up a JDBC pooled cache with min=5 and max=20 with FIXED WITH WAIT scheme. Load test with 100 users - all is okay and only get 20 conections. Load test with about 250 or more get 21 or 22, or 23 connections. What is going on and how can this be fi
-
I have 10.5.8 and want to upgrade, Do I have to download Snow Leopard before download the Mountain Lion?
-
What is the @List function?
I see this in a business rule but I cannot figure out what it is doing...
-
Hello, experts! I have the following problem: After spontaneous reboot of Windows (Windows Server 2003 EE) I start SAP in console (ERP 2005 IDES). But not all java-processes are started/visible. Namely, server0 and dispatcher were not started , only