I have snow leopard installed as an OS. When trying to reboot a MacBook Pro I am getting stuck on grey screen with apple logo and rotating symbol. What can I do?
I have snow leopard installed as an OS. When trying to reboot a MacBook Pro I am getting stuck on grey screen with apple logo and rotating symbol. What can I do?
Maybe this might help.
http://support.apple.com/kb/TS2570
Similar Messages
-
MacBook will not start. I have restarted with original CD. I have used Utilities and "no problem" with hard drive. I have reset PRAM. I have tried safe boot. Nothing is work. Gray screen with Apple logo and rotating wheel. Thanks for any suggestions!
Snow Leopard is a Mac OS X version. You say that it's the version you have in your Mac (10.6.8). Do a back up of your files, format the hard drive (using Disk Utility) and reinstall again
-
Hi my serial number on bottom of my mac is W8******66E when l try to turn the computer on it is just going to grey screen with apple logo and spinning wheel i have tried starting in safe mode and a few other suggested solutions and they have not worked?
<Edited by Host>What other solutions have you tried?
This may help you:
https://discussions.apple.com/docs/DOC-3353
Ciao. -
I Shut down my Mac by holding in the power button after my iMac froze and now when I try to turn it back it on all I get is the grey screen with Apple loge and the timer and doesn't get any further. I have tried the diagnostic test but nothing was found.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
Grey screen with apple logo after new HDD install
I have a mid 2010 iMac A1312, this was given to me recently with the knowledge of its bad HDD, so I bought a new HDD. I followed step by step instructions on how to replace a Hard drive and I did. I switched the computer on and inserted my Snow Leopard 10.6.3 install disk and clicked the icon. It is now at a light grey screen with a dark Apple logo. I have waited about ten minutes and restarted the machine. Ive tried all variances of startup holding down c, option, command r and so forth. Currently I am going to give it a good long wait of 20 minutes or so and see if I was just being impatient and not allowing the install software chance to start up. But in the mean time... any suggestions? I have read I need the original disks that came with the computer from factory to get a new HDD going. Is this true? thank you for your time!
it has now been 30 minutes and no change. I still have the grey screen with apple logo. please help
-
installed the ios 7.0.2 update to my iphone 4, now it is stuck on a screen with itunes icon and power plug.
I am unable to use the phone now. What should i do next? I plug in to itune in my computer and ask me to restore my phone? I will loose all my date?I hooked up itune and restore. after finished restores, it said my phone is in recovery mode and needs to be finish before using itune, my screen still show the itunes icon and power plug
-
installed the ios 7.0.2 update to my iphone 4, now it is stuck on a screen with itunes icon and power plug. is this corect? I am unable to use the phone now. What should i do next?
I hooked up itune and restore. after finished restores, it said my phone is in recovery mode and needs to be finish before using itune, my screen still show the itunes icon and power plug
-
I tried to download tI tried to download iOS 7.0.4 and have been stuck on a screen with iTunes logo and up arrow and a picture of charger plug. It has been this way for 2 hours. Help??
doreen329 wrote:
... have been stuck on a screen with iTunes logo and up arrow and a picture of charger plug. .
Your Device is in Recovery Mode and needs to be connected to the Computer you Usually Sync with.
Once the Device is asking to be Restored with iTunes... it is too late to save anything...
See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...
Be sure to Follow ALL the Steps..
Once you have Recovered your Device...
Re-Sync your Content or Restore from the most recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766 -
Hi, I downloaded Yosemite this evening. It downloaded fine, it installed fine and then it restarted the Macbook. Now it seems to be frozen. I have nothing but a grey screen with the apple logo and a bar that is half black and half grey. It's been like this for over an hour. Should I worry or is it still working at something? How do I fix this if it's not still working at installing something. Thank goodness for this poor old pc as backup.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
I have an early 2009 17 inch MacBook Pro that just went on the fritz. When turning on the power it will go into boot up mode to the gray screen with the apple logo, then the disc icon will be running and will continue running, not allowing to proceed to my desk top screen. It's pretty much locked up at this point where I have to do a forced shut down by holding down the power button. I've tried everything that I know of such as taking battery out and pressing power button for 5 seconds and then reinstalling battery. I've cleaned inside of computer with compressed air duster in can as well as other key commands for resets. I've read that this is a common problem with the earlier MacBook Pros. Is this a problem that I can fix or does it have to be taken in for service? Any solutions to the problem would be greatly appreciated. Thanks!
This could be a software/state problem or a hardware problem. Here are steps to resolve the former.
http://support.apple.com/kb/TS2570
https://discussions.apple.com/docs/DOC-5282 -
I cannot turn on my MacBook pro. When I turn it on all I get is a grey screen with a grey spinning thing under the apple. Can anyone help?
Reinstall OS X.
Reinstall Snow Leopard without erasing the drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
====================================
Reinstall Lion, Mountain Lion, or Mavericks without erasing drive
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
Reinstall Mountain Lion or Mavericks
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is
three times faster than wireless. -
I have a iMac (20-inch, Mid 2009). On start up It will sit at the white screen with the logo and the wheel that spins under it. It will not go past this point? Any ideas?
Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by one or more of these:
a. Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
b. Boot drive's directory has been corrupted - Repair with Disk Utility.
c. Critical system files are damaged or deleted - Reinstall OS X.
d. The disk drive is physically non-functional - Replace the hard drive.
Note that the information I have provided is what Apple recommends, If other users suggest different solutions than found here, then be sure what they recommend does not impact on your warranty, if any, or ability to get continuing Apple service.
Please don't start removing drives or changing cables unless you know what you are doing and have exhausted other non-invasive alternatives outlined here. If you perform any work yourself that is unapproved by Apple, then you will void any warranty you may have and lose all further Apple Support.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD. Simply boot from the Recovery HD to perform the above.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless. -
Installed tiger (formerly panther) now show only grey screen with apple. What should I do?
My Mac mini was 10.3.9 and I recently found that I no longer can view videos. I have a full version Tiger 10.4 so I installed it on the mini. Now it start with the right sound, the grey screen with apple comes up and that is it!! What do I do now?
You can try several trouble shooting steps are described in apple's trouble shooting article
http://support.apple.com/kb/TS2570
1) disconnecting all peripherals, including the ethernet cable
2) power on system
1) power off system
2) restart holding down the shift key until the apple logo appears
1) resetting pram
2) hold down command, option, letters p and r and press the power button. Wait until you hear two chimes
There are more ideas in the trouble shooting article above -
I have set up 3 mails in my outlook macbook pro, i am getting old mails for my company account mail, and i am not getting any mail to my hotmail, please help
daily i receive 100 old mails, which are already read
-
How do I reinstall my operating system (Snow Leopard) after a hard drive upgrade. I did a Time Machine backup before the new hard drive was installed. I put in the Snow Leopard install disc and don't get the icon I'm supposed to double click to install Snow Leopard and then the backup.
HELP PLEASE!!Is the new HHD in the MBP?
Is the new HDD formatted Mac OS Extended (Journaled)?
Where is the old HDD? In an enclosure? What is on the old HDD, your user data? Is the Snow Leopard System on it?
Do you have a separate Time Machine Disk with your user data?
Answers to these questions should give an exact status of your situation so that one can proceed in the right direction.
Ciao.
Maybe you are looking for
-
Photoshop cc 2014 crashes when i make a new file.
How Can I fix this?
-
Using Prelude to sort and organize a ton of media
So I have about 2 years of old behind the scenes footage (about 1tb) that is spread out through about 40 different folders. I have ingested the whole mess into Prelude, but I am finding it difficult to start the sorting process. What I would like to
-
Lost my ipod don't know the serial number
i think i lost my ipod touch 4 gen in ephraim today while i was there. the wifi is on but its not conected. i can't file a report because i can't remember the serial number and my account says that its not registered but i know that it is. how can i
-
Problems while creating an email account
Hej, end of July I bought a BB Curve 9320. Till today I was not able to create a mail account. A smartphone without email access. The problem is the missing possibility to create a internet mail account. I' m only able to put in information for a com
-
My G5 iMac has been acting quite strangely for the last few weeks. It's been randomly shutting off and restarting, but never when it's in use. Today, when I went to sign on, the power light was flashing quickly and there was a steady beeping noise al