I have to reenter my Wifi password every time I restart my Ipod touch. It used to retain the password but now it drops out when I turn the Ipod off. Any suggestions?
I have to reenter my Wifi password every time I restart my Ipod touch. It used to retain the password but now it drops out when I turn the Ipod off. Any suggestions?
Try:
ipod touch wont remember wifi password: Apple Support Communities
Also, have you looked at the previous discussions listed on the right side of this page under the heading "More Like This"?
Similar Messages
-
A thin line appears above the logo then the loading sign pops up and then the whole thing freezes! I read somewhere to hold the home button and then plug in the usb will help it be recognized by Itunes or help to restore it! I tried that it didn't work.I tried uninstalling Itunes and then re-installing it. I have the newest version of Itunes and don't know what else is left to do? can someone please help?
Thank you for reading!Try placing the iPod in recovery mode (I think that is what you were try to do) and then try to restore the iPod. For recovery mode see:
iPhone and iPod touch: Unable to update or restore -
Have to reboot my airport extreme every time i restart my PC.
Hello,
Why is it that i have to reboot my Airport Extreme every time i restart my PC? I am able to connect to the network but not the internet, unless/until i restart my base station.
My phones and tablets are connected to the internet, so i know the my ISP is not the issue.It is impossible to work this out without lots of details.
Like what PC OS do you run?
What connection, wireless or ethernet?
What you use test with the other if possible. Does it work for example swapping from wireless to ethernet??
I presume wireless as it is the most trouble prone.. When you start the PC does the wireless connect? Do you get IP by DHCP .. if so does it match what you get after a reboot.. look particularly at dns and gateway addresses.
Is the PC showing location as home or work/public.. it must be home to work properly.. also firewall might matter.
Also what type of wireless card is used.. poor windows drivers abound.. particularly Intel cards in laptops.
Is the wireless name SMB compliant.. ie short, no spaces and pure alphanumeric?
Is the wireless password mix of only case and numbers.. nothing non-alphanumeric? -
I am trying to put previously purchased apps onto my 2nd device but it asks for a password EVERY time. Is there a way to change settings to entering password while I am working? That is how my 1st device works.
Settings
General
Restrictions
Enter or make a restrictions passcode
set 'require password' from immediately to 15 minutes. -
I have Power Mac G5 1.8 single. I have a problem with ethernet port, before it was working with the internet, but now i shows it is connected even the cable is disconnected. I'm running Leopard 10.5. any help
Reset the PRAM.
http://support.apple.com/kb/HT1379
If that fails, reset the PMU.
Scroll down the following page and click the G5 link for instructions:
http://support.apple.com/kb/ht1939 -
I have turned iCloud off on my iPod touch 4th gen iOS 5.1.1 but I don't know how to turn it back on???
Go to Settings > iCloud and activate it
-
Have to reconnect to my network every time I restart
Every time I restart my computer, it fails to find my network even though the airport is on and the network is listed. I have gone through the network diagnostics which appears to work, but when I restart, it still can't find my network on its own for some reason. What's going on?
I think you have a corrupt .plist...
Maybe "/Library/Preferences/SystemConfiguration/preferences.plist", or "/Library/Preferences/SystemConfiguration/com.apple.airport.preferences.plist", (or whatever interface you're using, if not airport).
Back them up before trashing them, then reboot. -
Apple please help me
Good Morning
Greetings from me.
I used last 3 month IPHONE 5 in bangladesh. but now i facing a problem that is the signing problem
the phone is not open even i cannt enter this phone
is says
Sign in to ICLOUD
Enter the Apple ID password for
but i dont know the password. Please brother help me to use this phone. i brought this phone from some one 355pound. so i am in helpless.i am facing big trouble i dont have enough money for purchase another one. please help me...........................
<E-mail Edited by Host>You need the previous owner to unlock it, unless they do you have a brick there is no other way .
iPhone was probably stolen if you purchased on eBay, claim and get your money back
See here
http://support.apple.com/kb/HT5818
for explanation of Activation lock
APPLE will not help you -
I cannot get my ipod touch to airplay - I an get sound, but no picture that mimics what I see on my ipod, such as the game I am playing, any suggestions?
Mirroring is only available on iPhone 4S and iPad (Gen 2 and 3). In regards to airplay (which is a separate feature to mirroring), not all apps are enabled and this is up to the developer.
-
Firefox automatically downloaded and installed version 6 without my authorisation and now it has stopped working. I can't get it to run in safemode either. I have tried a total uninstall and reinstall but I get the same problem. Every time I select it a small crash window appears instead of the browser that asks me to report the crash. Now I can't find a link to re download version 5.
Here is a link for all the older versions of FireFox:
ftp://ftp.mozilla.org/pub/firefox/releases/ -
I have an iPod mini library which I have update. I now have an iPhone 4S which I have synced to the library using a MS XP computer. I can not figure out how to get the library to download to my iPhone?
Thanks, This caused me to go back and try again since the solution seemed so simple. What I did was when it started downloading, it started with the iphones apps to my computer. I did not want the apps downloaded on my computer so I stopped it. If I would have waited, the music was uploaded right after the apps were downloaded.
-
i have been trying to download and intsall the latest version of i tunes, however i tunes will not install because quicktime is not up to date. I have downloaded the version of the proper quicktime update but it will not install. i need suggestions on how to fix this. this is my first mac its an old ibook g4, and i have limited computer knowledge.
Hi, and welcome to Apple Support Communities.
Which exact iBook model is it?
You can choose from this list:
http://www.everymac.com/systems/apple/ibook/index-ibook.html
Which version of the operating system is it running now? (It is impossible for an iBook G4 to run Mac OS X 10.0.)
How much RAM is installed?
What kind of optical drive does it have? (CD-ROM, CD-RW, DVD, Combo, or SuperDrive?) -
Have to create a new folio every time I restart my computer, any fix?
I'm having some major issues with updating articles. When I shut off my computer, on restart I can't open or update the articles in my folio. The only way to get them to update or even connect to source files is to create a new folio and re-import all of my articles again.
I've tried:
-Checking for and installing all adobe updates
-Re-installing INDD and DPS
-Logging out of Folio Builder and back in
-Making sure I'm not connected to any other user servers etc.
Would really like not to have to recreate this folio everytime I shut down. I'm on CS6, Mac OS 10.6.8. Any ideas?I figured it out. I have to disconnect from servers and user drives, a problem I've experienced with Bridge and Photoshop in the past. I should have thought of it sooner:
http://forums.adobe.com/thread/765674
http://forums.adobe.com/message/3444550#3444550#3444550
Thanks team. -
I have installed the new iOS 7 on my I Pad and am having trouble with messaging, I reset the imessages and networking and the messages are still not being deleivered.
Reset all settings
Settings>General>Reset>Reset All Settings
Note: Data will not be affected but settings will be reset. -
I'm intended to control a machine wich was controled by a CNC and a PLC. My job is to substitute them by a PC with a 7344. The 7344 only has 5V I/O and I need 24V I/O to get this machine to work (24V relays, 24V I/O to the motor driver, etc). Can anyone tell me what converters/drivers to use?
Norick,
We have a solid state relay solution so you can convert the TTL signal to a 24VDC that you are looking, we use an interface called SSR Backplane that has modules (is configurable) selectable from digital input or output (3-60VDC) as well as others. All you need is the motion cable SHC68-C68-S, the cable adapter for SSR backplanes, the SRR backplane and the corresponding module you want. Special notes to watch out is that the backplane requires voltage supply (check the manual) and you can select from the 8, 16 or 24 channel configurations, 32 is not supported. The manuals have the information on which port access which relay. If you you have more questions after looking on this links that I included feel free to give us a call.
SSR Series Backplanes
SSR Series Modules
SSR Series Modules and Backplanes User Guide
68VHDCI-50F SSR 8,16,24 Channel Cable Adapter
68VHDCI-50F SSR 8, 16, 24 Channel Cable Adapter Installation Guide
186380-02 or -0R5(SHC68-C68-S)
Best Regards,
Nestor Sanchez
Motion Control Support
National Instruments
Nestor
National Instruments
Maybe you are looking for
-
PDP: How to transfer PR manually?
Dear expert, I met an issue that , in PDP, if the PR transfer failed, I need to transfer the PR again. Until now, I have only the resolution that enter an PR manually into table EPRTRANS and run report BBP_EXTREQ_TRANSFER manually. The reason why I d
-
RE: How can I call Windows .DLL components in Java
Hi, there, I have a wondows dll component registered on my server. I want to call this componet in my Java application(Servlet). Could you tell me the syntex or is this possible to do in this way? TIA, Xin
-
Text gets scrambled for a few seconds
The text on a webpage appears a bit scrambled and compressed for a few seconds every now and then. It's really disturbing when you try to read. It only started happening very recently.
-
Page not found or displayed in the approve step
Hi all when i am performing the approve step then i am able to do the mark as approved step. but there is no stop button is displayed for me when the approver wants to stop the task after marking as approved. how to gets displayed the stop button in
-
-14001 error occurs from system exec.vi only on one machine
I have a LV application that calls an executable that is bundled with the application using the System Exec command. I have tested it on our computers both pre-compiled and executable with no problems. It has also worked fine on a variety of custome