I loss BIOS password for my Portege S100

Hi
I have toshiba portege s100 i loss bios password when i search about it so i found a method i pressed ctrl, teb and ctrl,enter my leptop screen shows s/n and challenge code and system need response code but i do not know response code pleas help me i need response cod the s/n and challenge cod is as under,
pc serial no = 36738792g
challenge code= 7N67Y-YVDEA-XQ6VY-KMLCB-1F1ML
response code=
Thank you.

Hi
Unfortunately nobody here can help you with this. BIOS password is very important security feature and it cannot be solved on some public forums.
This can be solved with authorized service only.
Response code can be given by Toshiba only and they don't give it to anyone. Only authorized service provider can get it after check if notebook is not stolen.
Contact nearest Toshiba service provider and they can help you wth this.
Bye and good luck.

Similar Messages

  • Forgotten bios password for pavillion dv620us

    I've forgotten the bios password for my laptop. It's a Pavillion DV9620us. Can someone help?
    This question was solved.
    View Solution.

    Hi,
    Try entering:       klmn
                                       or
                                     ngcck
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • How to reset bios password for laptop( HP pavillion zd8060, pr315ua)

    I need to reset the bios password for my HP Pavilion Zd8060USA, Part #: PR315UA.
    Systm Disabled Code:00293 0r 02993

    Hi:
    Below is the link to the service manual for your notebook.
    http://h10032.www1.hp.com/ctg/Manual/c01383095.pdf
    Please read the instructions to clear the password in Chapter 1, section 1.2, page 1-4. 
    Wait 30 minutes, not 5. Five minutes is not enough time to drain the current in most cases.
    Paul

  • Find bios password for dm4 hp pavillion code# 68459741

    find bios password for dm4 hp pavillion code# 68459741
    This question was solved.
    View Solution.

    Hi,
    Try entering:     77531387
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Reset BIOS Password for Omni 27-1100d

    Hi,
    I try to use VirtualBox to run Ubuntu 14.04 x64 but I got this message
    "VT-x/AMD-V hardware acceleration is not available on your system. Your 64-bit guest will fail to detect a 64-bit CPU and will not be able to boot."
    When I try to enter BIOS Setup, it always ask for password. How do you reset BIOS Password for HP Omni 27-1100d?
    From what I'm gather from internet, I can force the BIOS to reset by altering the checksum or by taking off CMOS Battery. Is there any other way? I just want to clear the BIOS password not all BIOS configuration.
    Thanks.
    PS:
    I use HP Omni 27-1100d, dual booting Windows 7 (OEM) and Ubuntu 14.04 x64.
    This question was solved.
    View Solution.

    You can clear the BIOS password by using the procedure described in the motherboard specifications document. There is no need to remove the CMOS battery, which would probably remove the current BIOS settings.
    http://support.hp.com/us-en/document/c03305138
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • I don't know BIOS password for Satellite A100-528 PSAA2E

    hi..i have a problem...
    i have a laptop Toshiba SATELLITE A100-528 PSAA2E-01H00WGE....
    the problem is that i downloaded toshiba HW setup and i accidentaly set a password..
    .not a user password....it's propably supervisor password or bios password...
    .the thing is that i don't know what the password is...i boot up my pc and it don't let me get in windows if i don't type the password.....is there any way to remove the password ??
    it does not let me either boot from a cd or usb....i press F12 in order to choose to boot from cd or usb but it's still asks for the unknown password....is there any solution ??
    please answer it's critical !!
    thank you very much...

    >the problem is that i downloaded toshiba HW setup and i accidentaly set a password..
    >.not a user password....it's propably supervisor password or bios password...
    Thats weird because the BIOS or Supervisor password can be reset only by an authorized service provider.
    The BIOS password is a high security option which cannot be reset easily.
    So ONLY ASP can remove a UNKNOWN password.

  • Please reset my bios password for me on hp mini laptop

    someone enter a bios password on my hp mini laptop computer but i have no idea can someone help please error code is 2mc9142yp2
    This question was solved.
    View Solution.

    Hi,
    Try entering:    74eo3v7i27
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • What is the DEFAULT BIOS Password for my Probook 6550b?

    I have been struggling to find a DEFAULT password for my 6550b (i5 Windows 7)
    I want to change my boot order so I can install Windows 8, but I can't since if I install it, I would be stuck in limbo and I don't want to take the risk.
    I have previously cracked the BIOS Password on a Dell Latitude E4510 and everyone said that was IMPOSSIBLE! So I am sure you guys can help here, thanks

    Hello MazingerZ,
    Your ProBook is a Business model.  Your issue would be best answered on the HP Enterprise Business Community Forum
    Good luck!
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

  • I need the BIOS password for a Bios update

    Hi,
    can you support me with the BIOS password of my laptop?
    I want to upgrade to the latest BIOS version and found that a password is set
    It's specs are as follows.
    System  Hewlett-Packard HP ProBook 6470b
       Serial Number = [edited Serial Number by Moderator]
       CPU = 1 x Intel(R) Core(TM) i5-3320M CPU @ 2.60GHz
       Physical Memory = 8056 MB
       System Root = C:\Windows
       Video Adapter = Intel(R) HD Graphics 4000 [2112 MB]
       Video Settings = 1920 x 1200, 32 Bit Color, 60 Hz
       Sound Device = High Definition Audio Device
       BIOS = Hewlett-Packard  [HPQOEM - f]
    Can you find this out?
    best regards from Germany, Holger
    This question was solved.
    View Solution.

    Holger.
    There are no master password generators for ProBooks or EliteBooks and most business class laptops.
    You will need to contact HP.
    http://www8.hp.com/us/en/contact-hp/ww-contact-us.html?jumpid=reg_r1002_usen_c-001_title_r0003
    Or look at this link.
    http://forums.mydigitallife.info/threads/49497-HP-Probook-Elitebook-BIOS-Password-Reset-Utility
    Or replace the BIOS chip.
     http://www.ebay.com/itm/HP-Probook-4340s-4440s-4540s-4545s-4740s-6470b-6570b-6475b-Bios-Chip-No-Pass...
    The Ebay seller is in Berlin.
    REO
    I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damage that may arise to your system by using these services. Please be aware that you do this at your own risk.
    HP Expert Tester "Now testing HP Pavilion 15t i3-4030U Win8.1, 6GB RAM and 750GB HDD"
    Loaner Program”HP Split 13 x2 13r010dx i3-4012Y Win8.1, 4GB RAM and 500GB Hybrid HDD”
    Microsoft Registered Refurbisher
    Registered Microsoft Partner
    Apple Certified Macintosh Technician Certification in progress.

  • Forgot the "power on" BIOS password for my Stream 11 do 11wm notebook.

    Please help. Forgot the BIOS password on my  Stream 11 do 11wm notebook. The system disabled number is 93944559 I would sure appreciate any help I can get with this problem.

    Steps to be followed:Use the unlock code posted above to enter the BIOSDisable all passwords that are enabledIf asked for current password - type the unlock codeFor new password, just press ENTER keyRepeat the same for verify password column.Then leave the BIOS by saving & exit option to save the changes. Troubleshooting:Incase if the Password doesn’t work please try a Hard Reset as follows.Shut down the notebookUnplug the AC Adapter and then remove the batteryHold  down the Power button for 30 secondsPlug in the Power/AC Adapter (Leave the battery out for the moment) & Start the NotebookIf you now see a password box, Please type the same Password I shared before and press enter Hope this helps, for any further queries reply to the post and feel free to join us again  **Click the White Thumbs Up Button on the right to say Thanks**Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. Thank You,K N R KAlthough I am an HP employee, I am speaking for myself and not for HP

  • Need BIOS password for old ACS SE

    We recently upgraded our ACS SE 1112 to a SE 1113 model. The trade allows us to keep the old hardware. I want to use it for a test Windows or Linux server, however I can't seem to be able to break out of the locked-down Windows boot sequence. Occasionally I am able to press enough keys to get what looks like a BIOS password prompt. Does anyone know what that is?

    Thanks for the suggestion. I get challenged with 3 password prompts when I hit F12 during the boot sequence and neither password works. In fact, I'm not sure that is the BIOS password. But I did open a TAC case and they suggested removing the CMOS battery....which worked. Here's the sequence if I had to do it all over again:
    1) boot with a diskette to find a utility to remove the master boot record. I used a 3x diskette OS/2 and used FDISK.
    2) remove the cover. Take out the CMOS battery. Wait a minute or two and put it back in place.
    3) reboot. Do not (yet) select F1 to setup the BIOS. Just hit the prompt to continue booting. The default boot sequence will boot from the CD.
    4) Install your OS from the CD. During the install process if the box needs to reboot, do not (yet) hit F1.
    5) after installation of the OS, at the next reboot, select F1 at the prompt, set up the BIOS (date/time, etc), exit and save.
    It must have something to do with the SATA drive/controller and the IDE controller on the system board - but I could not find the correct BIOS settings to allow me to boot from CD if I pressed F1 after removing the CMOS battery and saved the BIOS configuration.

  • Remove the BIOS password for laptop HP Compaq 6520s

    Hello everybody!
    Notebook is my HP Compaq 6520s. I set the BIOS password, but now I have forgotten it. How can I remove the password now?
    Thanks everyone!

    I do not know what decade the last replier is from but is most apparent that they can not read the written word... the first person said, that they had a laptop not a desktop...  Most laptops that are under eight years old do not have pins to reset the bios...    Everything that the replier stated might work on a desktop computer to reset the password.. but since laptops are to easy to steal the companies have made it more difficult to enter the bios and change things when they are password... There are three ways to remove the forgotten password    1 remember it    2 call Hp to get the backdoor password  3  replace the motherboard.. that is it... most of the bios clearing programs are made for dos and will not work with windows above windows 98... xp vista and 7 are NT and will not allow access to the bios..........

  • How to disable bios password for desktop hp envy 700 056

    I tried to remove the battery out of the motherboard and wait for 1 minutes and more, and then put in back the motherboard, but the password is still there. I don't know how to remove or disable the bios password. I need help, please.
    Thank you very much.

    Hi,
    Review this posted HP information.
    HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
    HP Photosmart Premium C309G, HP Photosmart 6520
    HP Touchpad, HP Chromebook 11
    Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
    Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
    Windows 7/8 UEFI/Legacy mode, MBR/GPT

  • Need bios password for hpmini110-116nr #CNU9390T3N

    Didn't use for awhile and battery died locked out of and do not have
    BIOS password. Its for HP mini 110-1116NR halt code CNU9390T3N
    This question was solved.
    View Solution.

    You're welcome
    All the best,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Find bios password for dm4 hp pavillion

    Hi Guy's,
    I have a halt code of 50820390 - HP dm4
    Thanks'

    Hi,
    See your later post on the following link.
    http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and-Software/HP-DM4-Bios-Password/m-p/493881...
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

Maybe you are looking for

  • Convert as2 code to as3 please help

    function fDieList()     if (pDieList.length > 0)         _root.inSFX.die.start();         for (var _loc2 = 0; _loc2 <= pDieList.length; ++_loc2)             pDieList[_loc2].fDie();         } // end of for         pDieList = [];         actioner.pKill

  • Accessing View Object Information from JSP

    Hi! I know that my question it's a basic one, but I'm having some problems. Let me start by describing my problem. I need to implement an navigation select box to one table (this table will be a result of a query). I'm "building" the select box with

  • Frame size and compressor

    I had captured a mini DV movie in another program as an .avi file. When I import this file as is into FCE, its properties show in the browser as: frame size 720 x 480 compressor DV/DVCPRO - NTSC data rate 3.6 MB/sec I then used MPEG Streamclip to exp

  • Updating user fields through a user exit in CO01

    Hi.. I'm new to user exits and knw there are loads of user exits for CO01, but can't find the exact one to modify the user fields.. And also, would a simple afvgd-usr00 = 'some material' work??? Tnx..

  • Embed PDF form in a view

    Hello experts,   I am working on HAP_DOCUMENT, but could not able to solve the issue for past some time now.            The Issue is: in the view "layout_sap_standard.htm" , they are calling "body.do" controller to display the details of the part app