I'm getting no audio output...

on my newly updated version of garageband. I've check the preferences, made sure I have built in audio as my output. I've listened to songs in itunes and on youtube... Anybody got any ideas?

What about the Master Volume Slider on the Control Bar (drag the GarageBand window wide enough to make it visible)
This Slider is an additional volume control AFTER the volme slider on the Master Track (Alhtought both Meters, on the Master Track and the Control Bar, display the signal after the Master Volume Slider). More on those important details with signal diagrams in my new manual "GarageBand X - How it Works".
Here are a few trouble shooting steps:
If the Master Volume Slider (on the Control Bar) turned down, then there is no output signal
If it is up and you see a signal on the Meter, then you should hear it through the Audio Device you selected on the Output.
Select System Settings for the Audio Device, then GarageBand follows the setting you have in the System Preferences - Audio. It will then be the same as iTunes uses.
Last resort is to restart (I guess you did that already). This might correct any hiccups that could happen when switching between Audio Devices
Hope that helps
Edgar Rothermich
http://DingDingMusic.com/Manuals/
'I may receive some form of compensation, financial or otherwise, from my recommendation or link.'

Similar Messages

HT1222 my iphone 4S no longer plays music output to speaker after updating to version 6.1.3. I am unable to reset the phone to an earlier version! How do I get my audio output to speaker back? (music, audible, youtube, netflix))

my iphone 4S no longer plays music output to speaker after updating to version 6.1.3. I am unable to reset the phone to an earlier version! How do I get my audio output to speaker back? (music, audible, youtube, netflix)

So you have business contacts that were lost... do you not have these on a Database in some shape or form? Sounds like you need to invest in a RAID1 backup setup for your computer so you dont have this issue in the future.
As for repairing your problem, sounds like you are going to need to start from scratch at this point or if the data is still on your phone look into a program that can take the information from the phone onto iTunes.

Hey my headphone jack was broken and got stuck in may ipad, am not getting the audio output. Is there any solution for my problem

Please do help me

I too had a same problem, when I attached AUX IN pin of my car to my ipad it got stucked in it.I went to Apple Store, they were helpless and asked me to replace it with new one for 16000 INR.
What I did is, I took a refill of a pen and sharped its back so that it exactly sits into the gap. After thar I applied some pressure and pulled it out...I got the remaining part wich was stucked.
Try this, I hope this is risk free. All the Best.

Help!! No AUDIO output from iMac through FW to mixing board (zed r16)

With my system stated below, I run an Allen-Heath ZED R16 board via FW. PROBLEM: I get NO Audio output to the R16 when I play iTunes or DVD/CDs in the iMac.
I DO get audio feed when I playback projects from Logic.
I have checked all System Prefs on the iMac (cahnged to the ZED); on Logic (changed to the ZED). I tried all different channels, routing, etc. NOTHING.
Can someone help?

Well, the Allen-Heath support site had the answer... quite surprised and pleased!!
Have to reconfigure the iMac speakers in the Audio/Midi preferences. The details are found in this URL:
http://allen-heath.helpserve.com/index.php?m=knowledgebase&a=viewarticle&kbarticleid=238
The ZED R16 is a great board but certainly not Plug' n Play.

Help, basic question, no audio output?

I have a Mac Pro running latest version of Logic Pro. I'm not new to audio software (come from a Cakewalk background on the Windows platform), but I'm relatively new to Mac Pro and Logic Pro.
I seem unable to get any audio output from my setup when using a Logic Midi Track (i.e. GM Device Piano).
My hardware:
Mac Pro
M-Audio Axiom 25 Keyboard/controller (connected via USB to Mac Pro)
MOTU UltraLite (connected via FireWire to Mac Pro)
M-Audio ProjectMix I/O (connected via FireWire to Mac Pro)
I can bring up the Loop Browser and play loops and place loops in the Arrange view but I can't seem to use my USB/MIDI M-Audio Keyboard to generate any Audio via the Motu.
Also, I can see the Midi events in the Logic Transport Window.
If I load up garageband the M-Audio & Motu Ultralite work just fine, so I'm confused as to what I'm not doing right in Logic Pro? It must be something really basic I'm missing.
Sorry for such a basic lame question, but I'm stumped!
Thanks, Rob.

well of course there is no official word on when an update to logic will arrive with a significant GUI overhaul. personally I hope that such a step is taken carefully.. this software is the backbone of many people's working life, so and big changes to the interface are hopefully being considered and integrated carefully.
I'd hope that a major overhaul to the logic UI won't just be cosmetic. there is a lot of legacy code left over from emagic days that do not make use of the latest OSX technology and so are not optimised. an example - look at how slow the screenset changes are. there is always a delay in response time to when you change a screenset, in some cases this can actually be slower than it was on older machines running OS9. as far as I can tell this is because it's all part of some custom graphics code in logic and doesn't make use of OSX quartz and probably not the graphics card effectively either. as a comparison, look at how incredibly responsive exposé is. it always seems to stay that responsive regardless of CPU load, so there has got to be a way to make the GUI features of logic perform just as snappily as the system ones.
same goes for the painful, annoying delay in mouse click response time, which is worse since OSX than it was under os9. a rewrite of logic's UI will hopefully sort this problem out too.
these things may seem like irrelevant nitpicks, but trust me, when you become a power user and you are cutting audio and throwing parts of your arrangement around like nobody's business, the sticky slow response of the GUI really penalises you.

Final Cut 7.0.2/Tascam USB-2, US-144MKII audio output intermittent

Dear folks,
Hello.
I am continuing to have problems with getting sound out of my Tascam USB 2.0 inteface box using Final Cut v 7.0.2, on a Mac Pro 2x2.66 GHz Quad Core Intel Xeon, OS10.6.4 .
The interface unit is a Tascam US-144MKII, USB 2.0 Audio/Midi Interface.
I have down loaded its driver. It works fine as the system output and playing back from Quicktime player.
In Final Cut it is fine one moment, sometimes pops and clicks then it goes silent. It is unpredictable and unstable. It is intermittent, not working most of the time. I have refreshed the AV Devices, set audio output in Audio/Video Preferences and tried Sequence settings, as well as restarting the computer.
I am having to go Firewire out to an external deck to get sound out of Final Cut onto my sound system.
Final Cut seems to be the problem.
Any ideas?
Thank you for your time.
Bests,
Peer

I've had limited success across five suites. Running FCP 7.0.3 across all rooms, however I've only been able to get one room functioning in a limited way. It sees MIDI info in the Control Panel indicator and replays some fader level info, however only when stopping and starting FCP. Have been troubleshooting the issue and have downloaded the newest Tascam driver for the FW-1884 (from May 2010). Can get FCP audio output through the monitor bussing on the Tascam, however actual moving-fader still not achieved.
Called Tascam's (LA) help line and they couldn't give me any advice at all (as they would only comment on Logic issues and were unfamiliar with using FCP!)
Any suggestions from anyone?
Thanks.
Message was edited by: Christian Bass

Upgraded to 7.2 and totally lost audio output

I wonder if anyone can help.
I have upgraded from 7.1 to 7.2 logic pro. now when i try to open songs i've been working on, i get no audio output at alll, just some nasty clicks and pops.
all tracks look like they're playing and show bouncing meters, but the master output is showing no audio output at all.
this only seems to happen on songs i had started in 7.1 because if i just load up logic and start a new song there's no problem.
i thought an upgrade was supposed to iron out problems not create them!
anyone had the same problem or got any ideas i would appreciate hearing from you.
my system:
G5 dual 1.8 Gig
mac OS 10.4.6
logic pro 7.2
audio interface - Novation X-station

i've tried disconnecting the X-station and running logic on built in audio but exactly the same happens.
after more messing, i've found that there are a whole load of songs which won't play audio, these are all in one folder and are an album project.
other songs in other foldres seem to play OK.
i haven't made any changes to the folder and am totally confused as to what is happening.
when i open these songs and press play, i get a horrible click or pop but then no audio. however when i press stop i get the reverb tail of an audio track.
i thought i'd finished the album which is why i thought it was safe to install the 7.2 upgrade, however now the artist wants a few changes and i can't do anything at the moment.
andy
Do you get any sound from any sessions other than
what you've described?
Does this also happen with internal/BuiltIn Audio?
J

Is it possible to get the current output level??

Is it possible to get the audio output level of a stream (in this case a mic input going through GSM compression to an RTP socket).
I would like a couple of volume bars in my application so people can see how loudly they are talking.
If anyone has any ideas on how to achieve this it would be much appreciated!
Thanks,
Dex

You want a volumeter, i am also interesting in it

The "alsa audio output error: cannot write: Broken pipe" problem

[Solved]
(No place for this word in the Subject field, so I put it here.)
Hi Arch community!
I noticed I have this problem and not sure when in started. Several months ago I bought and installed new videocard "GeForce GT 630". Right after installation I lost sound in the system. Having internal sound card (in mainboard) and SB Audigy2 (PCI), I searched for solution and found I had to disable "snd_hda_intel" module to restore sound to work through PCI sound card. Did it.
echo "blacklist snd_hda_intel" >> /etc/modprobe.d/no-nvidia-sound.conf
After that sound was working as it should. And I noticed recently that during playing of any sound file the sound interrupts. If run VLC from CLI I get "alsa audio output error: cannot write: Broken pipe" message. And my system hasn't been upgraded since I don't know when. I still ran Firefox 26. So googled again and found it's a bug in a kernel or somewhere else.
==========================================
https://bugs.freedesktop.org/show_bug.cgi?id=69942 :
2013-10-01 01:39:40 UTC
I ran a system update last night, and this issue appears to have been corrected.
==========================================
And so I thought upgrade would fix my problem since mainstream bug is fixed. After upgrade sound interrupts again, maybe even more often.
Do you guys have this issue and does anyone have a solution?
Last edited by Mr. Alex (2014-06-26 18:55:59)

Not particularly wise to blacklist the module, since it probably is also used by the integrated sound card. With vid and pid you could just disable the nvidia card alone using parameter enable=0. Unless you do not mind having both disabled.
Where do I need to input "enable=0"? When I was searching for solution to make my Creative card work with new nVidia card I installed, the only way I found was blacklisting the module.
dmesg says:
[ 20.448086] nvidia 0000:02:00.0: irq 42 for MSI/MSI-X
[ 21.112331] NVRM: Your system is not currently configured to drive a VGA console
[ 21.112340] NVRM: on the primary VGA device. The NVIDIA Linux graphics driver
[ 21.112345] NVRM: requires the use of a text-mode VGA console. Use of other console
[ 21.112349] NVRM: drivers including, but not limited to, vesafb, may result in
[ 21.112352] NVRM: corruption and stability problems, and is not supported.
Then:
lsmod | grep 'snd'
snd_ca0106 36242 0
snd_ac97_codec 114896 1 snd_ca0106
ac97_bus 1270 1 snd_ac97_codec
snd_rawmidi 20278 1 snd_ca0106
snd_seq_device 5244 1 snd_rawmidi
snd_pcm 83207 2 snd_ac97_codec,snd_ca0106
snd_timer 19294 1 snd_pcm
snd 60780 6 snd_ac97_codec,snd_timer,snd_pcm,snd_rawmidi,snd_seq_device,snd_ca0106
soundcore 5551 1 snd
I guess my card is "snd_ca0106". If yes,
# systool -v -m snd_ca0106
Module = "snd_ca0106"
Attributes:
coresize = "36242"
initsize = "0"
initstate = "live"
refcnt = "0"
taint = ""
uevent = <store method only>
Parameters:
enable = "Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y,Y"
id = "(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null),(null)"
index = "-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1"
subsystem = "0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0"
Sections:
.bss = "0xffffffffa0814780"
.data = "0xffffffffa0813300"
.exit.text = "0xffffffffa0811a1e"
.gnu.linkonce.this_module= "0xffffffffa0814500"
.init.text = "0xffffffffa0817000"
.note.gnu.build-id = "0xffffffffa0811a30"
.rodata = "0xffffffffa0811a80"
.rodata.str1.1 = "0xffffffffa08123dc"
.rodata.str1.8 = "0xffffffffa0812130"
.strtab = "0xffffffffa0818c10"
.symtab = "0xffffffffa0817020"
.text = "0xffffffffa080d000"
__mcount_loc = "0xffffffffa0812f98"
__param = "0xffffffffa0812f18"
__verbose = "0xffffffffa0814460"
Where would I look for "max_buffer_size" parameter?

Audio output problem - using M-Audio Fasttrack

I had been using Logic Express (7.2.3) without any issues until recently plugging in a mic through my M-Audio Fasttrack.
I don't remember the exact chain of events - but at some stage, the software instrument outputs were no longer audible played either through the M-Audio, with earphones attached to its output, or through the laptop.
Even after disconnecting the Fasttrack, resetting the audio driver to 'built-in-input' and rebooting Logic Express, I still can't get any audio output from the software instruments. They aren't muted and the volume is turned up. Audio output from other programmes is working fine.
Can anyone give me any tips on how I could resolve this/suggest what I might have done to screw the audio up and what I need to do to undo it?
Thanks,
Antony

this is actually really simple
i just had the same problem with my m-audio and called support
when you plug in the m-audio fast track mac automatically sets the input and output through the fast track. To fix this you need to create an aggregate device. heres how:
click the finder in your dock
then click applications
in applications a utilities folder should appear...click that
in applications click Audio MIDI Setup
at the very top of the computer screen where it usually says what program is open it will say Audio MIDI Setup ..next to that click Audio
then click open aggregate device editor
you need to click the + to add a device
in the aggregate device screen it should say aggregate device.
below that check the option built in output
then check the option fast track (or device your using) the one that says 2 under the IN category and 0 under the OUT category.
click done
now open logic express (reopen if already open)
then click preferences
audio
under device tab the device option needs to say aggregate device.
click apply changes
and your done!
hope it works!

No Audio Output CS6 after Matrox update

Since I updated the driver for Matrox Mini / Max to 7.0.2 I now have no audio output for Adobe CS6 Premiere Pro. Levels are showing up on the audio meter, and the ASIO settings appear to be normal. Did Matrox switch up something. I thought I would ask here. (I exported file and audio is there...so this is just an output connection problem.)
The audio is normally routed through Realtek Digital Output Optical, which is working (audio works with other software.) Adobe ASIO is set to this working output.
I am thinking the Matrox install switched the setting...but thought I would ask here on the Adobe Forum first to see if there is a solution. Since it is a Saturday. Thanks.

Glad to be of help!
Yes, they have changed things with CS6.
Matrox's hand was forced by the changes made in Premiere. There are all sorts of settings that are now in different places.
This setting is obviously not covered by the Premiere help files, as it is not a Premiere setting. It is not as clear as it should be in the Matrox User Guide, either. Page 53 is as near as it gets, and that only tells you how to get the audio output through the MXO2. You have to infer that for output via sound card, you choose the other setting. Not good!

No Headphones Audio Output T440

Hi,
I have a Lenovo T440 running Microsoft Windows 7.
I cannot get any audio output on my headphones. The speakers work just fine. The headphone are in perfect condition and I have tried them on other audio devices. I have also tried to use other headphones just to be sure my primary headphones i not the issue.
The Realtek Control Panel recognizes the headphones as soon as they are inserted into the headphone jack.
Link to image 1
Headphones is not muted from Mixer.
Link to image 2
I have the latest Realtek Drivers and client control panel installed. I have selected headphones from the Realtek Control panel.
Link to image 3
When I click the play button for the test, I get no audio output.
I have tried to uninstall the sound card from System>Device Manager, reboot, reconfigure the sound card, reboot again and still no audio. Device Driver Infromation is as follow:
Link to image 4
This thing has been going on for quite sometime now for many people but apparently no forum has posted a solution. Would appreciate any help.
Moderator note: large image(s) converted to link(s): About Posting Pictures In The Forums

Classic mode should make the headphones option disappear as it autoswitches on attach.
Try a bootable Linux live environment; if it doesn't work there, you might have a damaged headphone jack.
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

Why no audio output?

I have been wrestling with the options offered by FMLE3.1 and using it in association with ManyCam... I now think I have pretty good control over all the video source conflict issues, but one thing I have been totally unable to understand is why I cannot get any audio output, either into my headphones or to justin.tv which I am using to broadcast... except, interestingly, for a fleeting couple of minutes recently, which didn't appear to be the result of anything that I had done, and I certainly haven't been able to replicate it!
Each of my cameras, including the webcam, has a microphone associated with them, and they all show up in the list of recognised devices. The webcam mic is the only one which registers on the audio meter to the left of the video preview pane, even when the webcam is not selected, but still there is no output audio signal details showing up on the encoding log... I've looked for the obvious mute buttons, but someone out there probably has a simple solution that I haven't dreamed of!

Another worthwhile time/pitch related product is from Prosoniq. The version of Nuendo (not the latest) the University uses ships with the MPEX algorithm, which is related to to their flagship product.
http://www.prosoniq.com/www/TimeFactory_II.html
I've used it a bit to create the double-time/+1 octave Les Paul & Mary Ford guitar sound for a class demo demo and thought it did a very good job.
Yes, there is a Demo.

I am trying to display the output from my ipod touch on apple tv. i can get the audio but no video. please help

i am trying to display the output from my ipod touch on apple tv. i can get the audio but no video. Thank you for any advice.

What output are you trying to get to your tv?

ASUS EAH5450 silent graphics card to my Pavilion m7210 desktop but get no audio via HDMI output.

I have installed an ASUS EAH5450 silent graphics card to my Pavilion m7210 desktop but get no audio via HDMI output.I have 2 high Definition Audio Controllers in Device Manager, One has an exclamation mark with message
" This device cannot find enough free resources that it can use. (Code 12)
If you want to use this device, you will need to disable one of the other devices on this system.
You need to restart your computer before the changes you made to this device will take effect."
What do i need to do to get this to work ?
Thanks

Hi,
Welcome to the HP Forum!
kommy wrote:
I have installed an ASUS EAH5450 silent graphics card to my Pavilion m7210 desktop but get no audio via HDMI output.I have 2 high Definition Audio Controllers in Device Manager, One has an exclamation mark with message
" This device cannot find enough free resources that it can use. (Code 12)
If you want to use this device, you will need to disable one of the other devices on this system.
You need to restart your computer before the changes you made to this device will take effect."
What do i need to do to get this to work ?
Thanks
The other HD Audio device is likely to be the Realtek ALC880 8-channel High Definition onboard sound. This is a bit of a decision point. If you plan on always using the AMD High definition Audio as your default ouput through an HD TV with HDMI out, then you can disable the Realtek HD audio device. Once that is done then restart the PC. Go to the Control panel and select sound, now sellect the AMD HDMI out and right-click and select it as the default. There should now be a green checkmark next to it. Now you can select Configure to test it.
Kind regards,
erico
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

I'm getting no audio output...

Similar Messages

Maybe you are looking for