I'm receiving error Boot Device Not Found and Hard disk not exist when I boot up my laptop

I'm receicing the error Boot Device Not Found when i power on my HP G60-235DX laptop.  After following HP's recommended troubleshooting steps, I receive error Hard disk not exist.  Hmmmm....that's a little concerning.  My guess is I need a new hard drive?    I have the 17 recovery disks I made when I setup this laptop, however I'm not sure if they will resolve this issue.  Any suggestions?

One of 3 things has happened, listed from most likely to least likely
1. Hard drive has died, replace it with one of the same size or larger, then use the HP recovery discs to re-install windows.
2, The motherboard has serious problems. (Replace the notebook)
3. The hard drive cable that connects it to the motherboard has somehow failed, not very likely. (replace the cable)
Replace the hard drive with a new one and use your recovery discs to get Windows back on it.
Here is your service manual, will show you how to replace the hard drive
http://h10032.www1.hp.com/ctg/Manual/c02985882.pdf
Recovery Instructions for Vista
Recovery Instructions for Windows 7

Similar Messages

  • Boot device not found. "Hard disk not exist". windows not booting

    Product: HP G72-110SA
    OS: Win7
    two days ago, I was installing updates on my computer and when it was about to restart, it froze. After waiting for 10 minutes, I had to turn it off by pressing the off button. From then on, the computer turns on but shows a message "Boot device not found".
    I have tried all the BIOS tests that I could find on the net for the hard disk, eg: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01443465&tmp_task=solveCategory&cc=uk&dlc=en&la...
    This gives me a "Hard disk not exist" error. I tried resetting the BIOS, that didn't work. I tried taking out and putting back in the battery, the memory and the hard disk. Still no luck.
    I then booted ubuntu from cd on the computer. It works just fine, including the internet etc EXCEPT the HDD is still not detected.
    I had some pretty important stuff and no back up, so would appreciate if someone can help me get back the data. If not, even if I know its just a HDD failure and not a motherboard/BIOS problem, it will be a relief as its probably fixable.
    Thanks

    Hi there ,
    Thank you for visiting the HP Support Forums and Welcome! This is a great site to get answers and ask questions. I would be happy to assist you. As there are many models of HP Notebooks, I would need the model number. (How Do I Find My Model Number or Product Number?) When I went to www.hp.com/go/techcenter/startup, it gave me documentation and troubleshooting steps to follow. One of the documents it provided is called Hard Disk Error Displays before the Computer Starts. NOTE: I recommend at this point you make an immediate backup of all important data and files. Here are instructions on how to Backing Up Your Files (Windows 8). Please follow the troubleshooting steps provided, re-post with the results of the troubleshooting in detail. Thank you.

  • HELP!!! Boot Device Missing!! Hard Disk Error!!!

    I turned on my laptop and it said "Boot Device Missing" (it said Hard Disk Error sometimes) so I went in to the systen diagnostics and did a memory test (which I passed) and Hard Drive Check. I heard that if you pass the hard drive check you can fix this problem, but it said SMART Check and Short/Long DST was not available. I also went to the bios and I changed the settings to defaults (F9) and saved and exit (F10), tried shutting the laptop down, removing all the CD, USB, everything, and turned it back on, but those didn't fix the computer. I also watched some videos on Youtube that you can unscrew the bottom part and check the hard drive but I couldn't find where to unscrew and look for the hard drive. Is there any way that I can fix this without sending it to repair because I need to use this laptop everyday.

    Sounds like the hard drive has failed and will need to be replaced. If you are still in warranty HP will send a replacement. If not a retail laptop SATA hard drive can be used.
    Your Maintenance & Service Guide shows what size hdds you can use.Also shows how to replace- or check connection for secure fit before replacing.
    http://h10032.www1.hp.com/ctg/Manual/c04402649
    Btw-any tme you need it you can access User Guides, Specs, drivers,etc for your model using the button at top of this page titled "Support", then click "Support & Troubleshooting" from the menu. Enter your Model Number. After entering click 'Go".
    ******Clicking the Thumbs-Up button is a way to say -Thanks!.******
    **Click Accept as Solution on a Reply that solves your issue to help others**

  • Hp dv4-2112tu no boot no display , ram and hard disk are ok and checked, shows caps num led blinking

    Hello Sir/Madam,
    I have HP DV4-2112TU
    My laptop doesn’t boot completely and shows blank black display. CPU fan running normally and hard disk rotating normally.
    Battery charging is ok and charging-power led glows normally. Caps lock and Num lock led flashes 3 times and then wait for one second and then flash again and so on. Laptop is stucked in booting process.
    I have checked both of my RAMs and Hard Disk in Another Laptop. All are working fine and shows no issues.
    I have also checked my laptop installing new RAM in both ports (simultaneously) and a new Hard Disk but Laptop shows same problem - no display no boot.
    I showed my laptop at an authorised HP Service Centre... they told me that the problem is related to my Hard Disk....But this is wrong Because a faulty hard disk is never cause no display and no boot and even no BIOS POST message. They told me wrong cause of fault because I have checked Hard Disk and it is OK.
     Can anyone tell me what are the issues related to my Laptop..... …..
    Thanks in advance.
    This question was solved.
    View Solution.

    Hi,
    The 3 blink pattern does correspond to issues with the memory modules, see the document below:
    Computer Does Not Start and Emits an LED or Beep Code
    Since it sounds like you've done everything possible to eliminate the memory modules themselves as the source of the problem.  Based on your description, I'd agree that the problem is probably not the Hard Drive.  Which unfortunately leaves us with a problem with the Motherboard as the only component that might be implicated and that hasn't been changed out yet.  It could be as simple as a bad connector, or something less easy to detect in the logic on the board, but either way, it seems like it would need to go back to a service center for repair.
    R
    Although I am an HP Employee, I am speaking for myself and not for HP.

  • Start-up problem with hp pavilion dv6t-7000‏: "Boot Device Not Found. Hard Disk (3F0)" error

    I started getting start-up problems with my hp pavilion dv6t-7000‏.  It happens intermittently. 
    The boot error is:
       Boot Device Not Found
       Please install an operating system on your hard disk.
       Hard Disk (3F0)
       F2 System Diagnostics
       For more information, please visit: www.hp.com/go/techcenter/startup
    Could a faulty BIOS update cause this problem?
    Anyone else who may have experienced a similar problem?
    I'd appreciate any help about this problem.  Thanks.

    Hi
    Please find the link given below might help you to fix your issue.
    Resolve Boot Device not Found Error Message
    Let us know how it goes!
    "I work for HP."
    ****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    Regards
    Manjunath

  • I Mac Not working, and Repair Disk not working

    I have been trying to help out a friend with his I Mac loaded with OS X. It will not load up just by pressing the power button. I have tried running the Disk Utility and get the following messages. I am probably at the understanding of this hard drive is just toast. My next step will probably be to Erease the hard drive completely and try to install the OS X. But i am a little leary about doing that. If anyone could suggest something before I do this, that would be great. All so I have tried booting from the install disk and reinstalling the OS X with out the Formatting of the disk and it does not Allow me to access the Mac HD. There is a big yellow "!"

    I cant access any of the files on the hard drive to back up. Do you know of a link on how to format and reinstall. It would be my first time. I have diskwarrior and it will not load at all.
    Under the Erease tab I have
    MAC OS Extended
    MAC OS Extended (Journaled)
    MAC OS Extended Case Sensitive
    MAC OS Extended Case Sensitive journaled
    MS-DOS Fat

  • Grey Screen on Start up and Hard disk not working

    Hi , I was working and suddenly some popping noises came out of the hard drive. I tried to save my work but i couldn't because it got "stuck". I had to turn it off and when I restarted a grey screen appeared without the apple logo. It won't start up and starting from cd, safe mode, single user mode don't work. I reset the PRAM too and nothing works. I'm worried about recovering the data... what should I do? I have work there that i need!!!
    thanks

    thanks for your reply. I took my powerbook to 2 apple authorized technical service and both of them told me that they couldn't get the data using disk warrior.
    I already removed the hard drive and replace it with a new one. However I still want to recover data. I plug the hard drive to my home powermac with a usb connector and using disk utility and terminal i was able to "see" the drive but not mount it. In disk utility the drive appears as 0 bytes.
    I want to try using Terminal or Single user mode to mount the hard drive, and/or repair it and try to recover some important files that I urgently need. Do you know how?

  • I have OS10.6 and when I try to update I receive error message after validating packages and updates to not tke.

    I have OS10.6 and when I try to upload updates I receive an error message when validating the packages. No updates take place.

    Are you using Software Update? And what is the error message?
    You are on 10.6.0? Why don't you download the combo updater for 10.6.8 directly from Apple and try to install it from there:
    http://support.apple.com/kb/DL1399

  • Long wait on Startup and Hard Disk not found

    Hi. I don't know if these problems are related to each other, but they both showed up at the same time. I upgraded to Mountain Lion recently, and these appeared after that.
    I'm getting a long wait on startup (before I can select my username), which seems to be related to this timeout in system.log
    Aug 16 13:26:29 point configd[18]: InterfaceNamer: timed out waiting for IOKit to quiesce
    Aug 16 13:26:29 point configd[18]: Busy services :
    Aug 16 13:26:29 point configd[18]:   MacPro3,1 [1, 80583 ms]
    Aug 16 13:26:29 point configd[18]:   MacPro3,1/AppleACPIPlatformExpert [1, 80461 ms]
    Aug 16 13:26:29 point configd[18]:   MacPro3,1/AppleACPIPlatformExpert/PCI0@0 [1, 80436 ms]
    Aug 16 13:26:29 point configd[18]:   MacPro3,1/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI [1, 80427 ms]
    Aug 16 13:26:29 point configd[18]:   MacPro3,1/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2 [1, 80349 ms]
    Aug 16 13:26:29 point configd[18]:   MacPro3,1/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleAHCI [1, 60820 ms]
    Aug 16 13:26:29 point configd[18]:   MacPro3,1/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleAHCI/PRT3@ 3 [1, 60366 ms]
    Aug 16 13:26:29 point configd[18]:   MacPro3,1/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleAHCI/PRT3@ 3/IOAHCIDevice@0 [!matched, 1, 60366 ms]
    Also, hard drive I just bought (in "Bay 4", that is to say, port 3 in internal 0-based numbers) claimed to have been "ejected improperly" during a clone (using Restore from Disk Utility) and now doesn't show up, even in /dev/, although it is visible as "Unknown" in System Information. (It was visible for a few days before this.)

    Hi,
              Follow the steps listed in the below link
    http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and-Software/quot-Hard-Disk-3F0-BootDevice-n...
    "I work for HP."
    Please click the "White Kudos" star to say thanks for helping.
    Please mark "Accept As Solution" if my help has solved your problem.

  • HP G56 Notebook Prod id XG773UA#ABA - Hard Disk Not Exist error. I've purchased a new bigger HDD.

    Machine will not recover. Hard disk not exist error. Bought new bigger HDD and same problem on doing recovery procedure.
    Coulo this be a BIOS battery issue? Please help. Thank you. AJL

    Several things can cause the bios to fail recognize the hard dirive.
    0. Try loading bios defaults, save changes on exit of bios, see iff the error persists.
    1. Bad hard drive (try another hard drive)
    2. Bad hard drive data cable (replace cable)
    3. Failed hard drive controller on the motherboard (replace motherboard)

  • Boot device not found, hard disk not exist.... does that mean my computer is dead?

    Suspecting that Im in a world of hurt here. I tried turning on my computer and it says "boot device not found" - run in test failed... when I hit F4 and run a hard disk test it says "hard disk not exist". The memory test passes, but under the boot device not found it says in blue "please install an operating system on your hard disk"... and to make matters worse it's making some funny noises when it tries to boot.
    Is there any hope at all that this computer will work again? Is there any chance that any of the things I had on my hard disk can be recovered?
    This question was solved.
    View Solution.

    You're very welcome, Jonathan.
    dv5 still isn't enough info for me to provide the service manual (in case there are differerent ones for the different dv5 models).
    However here is the link to the service manual I randomly pulled.
    http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c01550108/c01550108.pdf
    Assume it is safe to say all dv5 models come with SATA notebook drives.
    So, if you want to spring for $15, you can get this enclosure which apparently has very good reviews.
    http://www.newegg.com/Product/Product.aspx?Item=N82E16817182138
    From what you are describing (noise and stuff), I would say you don't have much of a chance to recover data but that is up to you if you want to try the enclosure or not.
    Here is what I recommend:
    Yank the hard drive, and power on the notebook.
    If the odd noise you heard is gone, then you can pretty much safely assume the drive was the cause, and that replacing the drive, and reinstalling the operating system will solve the issue.
    If the noise is still there, then there could be another issue, and it might be risky throwing good money after bad.
    Paul

  • Compaq presario cq61-411wm no booting device error/"hard disk not exist" help!!

    screen is cracked so hooked up a external monitor. no bootable device error in white on black screen. did tests all passes except hard disk. this one gives " hard disk not exist" error..trying to save all my pix of my sons on computer.someone please help!! thanks in advance!! =D

    Did you drop the laptop? If the computer is not "seeing" the hard drive your only hope is that the hard drive got knocked loose and is still good, just not connected. Otherwise a drop that can crack a screen may well have also killed the hard drive.

  • Hard disk Not found Error

    My computer suddenly after working properly the day before, started displaying an error that says hard disk Not found. It is not booting up to windows aince the hard disk has been disconnected in some way. It is still under the hp manufacturers warranty till auguat of 2015, so would I be able to send it in for either a device replacement or a service order to correct the error. Also there is a small crack in the body near the charging port, but that is from a drop from eariler. Please get back to me as soon as possible, my son needs to use this for his computer science class.

    You should contact HP directly to arrange to have the notebook sent in for warranty repair.
    Use one of the contact options described in the web page at the following URL.
    https://support.hp.com/us-en/contact-hp/product/HP-Pavilion-13-a000-x360-Convertible-PC/6936239/mode...
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • HT1926 Have the same problem as many other users: tried to update iTunes on Windows 7 today; first message "unable to locate component- MSVCR80.dll was not found" then "iTunes was not installed correctly. Please reinstall iTunes - Error 7 (Windows error 1

    I have the same problem as many other users: updated iTunes on Windows 7 on Jan 26, 2014 and iTunes does not open.  First message "unable to locate component- MSVCR80.dll was not found" then "iTunes was not installed correctly. Please reinstall iTunes - Error 7 (Windows error 126)". When will Apple fix this? Don’t feel like uninstalling all Apple software and then re-installing it as suggested, as I am on a terribly slow internet connection while travelling in the DR Congo.

    Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (later)
    Remove all of these items in the following order:
    iTunes
    Apple Software Update
    Apple Mobile Device Support (if this won't uninstall press on)
    Bonjour
    Apple Application Support
    Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
    The uninstall and reinstall process will preserve your iTunes library and settings, but ideally you would back up the library and your other important personal documents and data on a regular basis. See this user tip for a suggested technique.
    Please note:
    Some users may need to follow all the steps in whichever of the following support documents applies to their system. These include some additional manual file and folder deletions not mentioned above.
    HT1925: Removing and Reinstalling iTunes for Windows XP
    HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
    tt2

  • IPod Nano: Error Message "The USB device has malfunctioned and Windows does not recognise it"

    Hi everyone, I just received 2 brand new iPod Nanos for my kids for Christmas, thought I'd be smart and sync them both now before wrapping them so I don't have to be messing around with them on the day. One synced without a problem, then using the same cable, same computer, same USB port, the 2nd one came up with "The USB device has malfunctioned and Windows does not recognise it" I've tried restarting my computer, unplugging and reinserting the USB. Is there anthing else I can try before returning it? Thanking you for any help.

    I have solved my problem, I ended up ringing Apple and got an awesome lady who told me to reset it by pressing the sleep button and menu button together for about 10 seconds and once it actually turned on for the first time the computer then recognised it, so it's all good, :-) Thank you lovely lady!

Maybe you are looking for

  • How to Avoid Open Sales Order Value from Credit Check

    Hello Everyone, We have a problem with Credit Management, When my user run the execute credit master sheet, system is considering open sales order value under Credit limit used. My user do not want consider open sales order value, they want only Open

  • Align Right

    Hi, I'am downloading a idox to a txt file with gui_download. And i'm cutting the blank spaces between the fields.but in one ofe the fiels i want that the field appers with all is lenght and with teh value of 0 align to the right. i have used one invi

  • LUMIRA Server 1.17 - Share option

    Hello, I created a stroy and a dataset and want to share this with other users. I created a user with role sap.bi.common::BI_DATA_CONSUMER but when I click on Share it opens up a pop up (see attachment) and from there it asks for "roles" to be assign

  • Nokia 3600 slide --- how to manually change networ...

    I just purchased a Nokia 3600 slide and want to set the phone so I can manually select the network.  I have a SIM card through a company called eKit and while I am in France, I need to be able to manually select the network with the best coverage.  T

  • Illustrator cc don't start after the new update

    Illustrator CC don't start after I update this. I should loading the font Verdana, but Verdana is activ. What can I do now?