I mac is snow leopard I bought for 19.99 mountain lion online an my computer has gray screen with the spinning wheel and don't work help me z
My computer I Mac is 10.6.5 I think but the issue was when I update it ask me for version 10.8.5 that was mountain lion wich I bought it for 19.99 Iand know is not working it had a gray screen with spinning wheel I have snow leopard on my iMac I bought mountin lion know the screen I grey I can't do nothing I reboots don't work I inserted the cd for my I Mac don't work can't do nothing I can't remove the cd can someone help me .
To get the CD to eject, hold down the mouse, or if you use it, trackpad, button while you reboot ... keep holding the button down until it ejects. If that doesn't work, this Apple note has some other steps.
See this Apple note on steps to take to deal with the grey screen.
Your iMac needs to be mid-2007 or newer with 2GB minimum memory (4GB+ is recommended) and 8GB or more of available disk space. You also should be at OS X 10.6.8 Snow Leopard to access the App store and install OS X 10.8 Mountain Lion.
Similar Messages
-
My MacBook Pro stated that it needed to be updated. I clicked yes to restart the computer and update but when it restarted it stays on the gray screen with the apple logo and then pops up, stating "unable to find driver for this platform." What do I do?
Boot into Recovery by holding down the key combination command-R at the startup chime. Release the keys when you see a gray screen with a spinning dial.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with networks that require any kind of authentication other than a WPA or WPA2 Personal password.
When the Mac OS X Utilities screen appears, follow the prompts to reinstall the Mac OS. You don't need to erase the boot volume, and you won't need your backup unless something goes wrong. If your Mac didn’t ship with Lion, you’ll need the Apple ID and password you used to upgrade, so make a note of those before you begin.
Don't install the Thunderbolt update -- it's defective. -
My Imac is not starting , I get a gray screen with the logo and a bar below and about one minute the bar desapier and shot off by itself. I try evething that I can think of and not luck. I did disconect all accesories and still the same, I use the start up disc and same.. now I can not get the disc out.
Please advise what I need to do to solve the problem. Recently this computer was upgraded from 10.4 to Mountain lion and add more memory.Thanks for your help.
Same thing happen when I hold the button, it idle for a while and then turn off by itself. Any more suggestions?
I got the disc.. -
On start up my Mac Book Pro shows a white screen with a spinning wheel. I have tried starting up with the Snow Leopard disk - all I get is a blue screen. I guess that this is a major repair job??????
If you have the exact same problem - take the computer to an Apple store or an AASP. Whichever is more convenient for you. If you have AppleCare call them!
-
I am now running on OS X Snow Leopard. If I upgrade to Mountain Lion, will all my files and data and bought programs disappear?
As Austin Kinsella1 says, it's a good idea to check your program versions.
I have found this site really helpful with that:
http://roaringapps.com/apps:table -
I used utilities to source my 10.6 snow leopard install disc to my main hardrive, and now when I turn on my computer the apple with the spinning wheel stays on the screen and stuck like that. How do I fix it Help please. I already tried all the commands such as Command R, Holding down the Option key, C and holding down shift at the start up but nothing happens.
initialy All I was trying to do was downgrade 10.7 to 10.6 .You have to consider the possibility the hard drive may be dying. If your data isn't backed up, try one of the tools below:
https://discussions.apple.com/docs/DOC-1689
Once you are sure your data is backed up, we can examine other possibilities. In the meantime call AppleCare for your original installation DVDs. You may need them. -
i have macbook air 13,3" but when i go to:From the Apple () menu, choose About This Mac. Click More Info. For OS X Mountain Lion, click System Report. MacBook Air 11 inch mi 2011, why why please
Informations matériel :
Nom du modèle: MacBook Air
Identifiant du modèle: MacBookAir4,2
Nom du processeur: Intel Core i7
Vitesse du processeur: 1,8 GHz
Nombre de processeurs: 1
Nombre total de cœurs: 2
Cache de niveau 2 (par cœur): 256 Ko
Cache de niveau 3: 4 Mo
Mémoire: 4 Go
Version de la ROM de démarrage: MBA41.0077.B0F
Version SMC (système): 1.73f66
Numéro de série (système): C0*******JYC
UUID du matériel: ****
<Edited By Host> -
I have a canon multifunction printer that used to work with snow leopard but since I updated to mountain lion it stoped working. How do I make it work again?
This problem is not unheard of when upgrading from Snow Leopard. It is usually solved by completely deleting the existing printer in System Preferences > Print & Scan, and adding it again.
-
I have Logic Pro 8 on my Snow leopard macbook.Can I upgrade to Mountain Lion?
i have Logic Pro 8 on my Snow leopard macbook.Can I upgrade to Mountain Lion?
octopi wrote:
It's not a bug. Although Logic 8 will run under 10.7.x and 10.8.x the installer contains PPC code which simply does not run in 10.7.x, 10.8.x and 10.9. The app is fine, the installer is the issue.
Some research on this issue has led me to the conclusion that the commonly held conception that the installer has PPC code is flatly incorrect.
That misconception is due to the fact that the PowerPC dialog box is triggered by any attempt to launch the installer app.
The "bug" I reference triggers this dialog box; not PPC code within the Logic Pro 8 app.
At the end of the day, the result is the same: the installer app will NOT work in Mt. Lion without modification. I have been given a tip on how to make a modification that will allow an analogous program's installer app work in Mt. Lion, but since I do not have access to a copy of Logic Pro 8, I cannot test this theory.
So, yes, the best approach is to be sure it is fully installed before the upgrade! -
I still have snow leopard, can i switch over to mountain lion or i need to have lion first?
i still have snow leopard, can i switch over to mountain lion or i need to have lion first?
If your system meets the Mountain Lion specs, http://www.apple.com/osx/specs you can go directly to ML from Snow Leopard.
-
Mac Book Pro on boot up, the apple sign will appear with the spinning wheel. After a period of time the screen will turn grey, but the mouse will still operate, but not boot up.
If it was purchased brand new then it's running a version of Lion, so to reinstall Lion:
Reinstalling Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Continue button. -
I want to disable my mac.com mail, I know how to delete it but I cannot get into mail to do this, whenever I click on mail, or mail in system preferences to open it I get the spinning wheel and have to force quit. I am running a Macbook 10.7.5
Thanks,
Edward.You can't merge Apple IDs. You also can't cancel (delete) and existing ID, you can only choose to stop using it.
If your old ID was compromised and you can no longer access it, you'll have to contact Apple for assistance. Go to https://expresslane.apple.com ; click 'See all products and services' at the bottom of the page. In the next page click 'More Products and Services, then 'Apple ID'. In the next page select 'Other Apple ID Topics' then then 'Apple ID account Security’. -
Hi, I am not able to reboot my Mac desktop.
When I switch on the Mac, I get a white screen with the Apple logo and the little rotating circle.
The system refuses to boot.
What can I do?
MarcusWe need to get you moved. This forum is for mini-tower Macs built between 1998 and 2005 and doesn;t get as much traffic ("eyeballs on the problem") as the forums for newer Macs.
Please do "About this Mac" from you Apple menu and tell us what that says for "processor" and Mac OS version. Looks like this:
or this for later Mac OS versions:
With that we can figure out which of the two iMac forums you need and get the Hosts to move your post. -
I have an early 2008 MacBook and running iOS Lion. I just turned on FileVault and restarted my computer as instructed. It told me before hand that I would still be able to use my Mac while the files were being encrypted. However, when I logged in on the secure gray login screen, I was only directed to a plain gray screen with the apple logo in the center. There are no time turners or anything moving. Is my Mac encrypting or is it frozen in some sort of way? If it is encrypting, how long does it usually take? and if it is frozen, how do I unfreeze it?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.
Maybe you are looking for
-
I never set a restrictions passcode but my ipod is asking for one help?
Can anyone help me? I'm trying to do a reset of all settings but it asks for two passcodes, my normal one to unlock my ipod but then it asks for a second passcode called a restrictions passcode but I never set one.
-
What's wrong with my Access Connections?
Can u help me? When I upgrade the Access Connections to v5.61, I can't get into the Access Connections. Symptom 1: the process is running in the task manager, but no user interface comes out. Symptom 2: when I choose the profile of wireless network,
-
I have downloaded a trail version of Illustrator and it will not open.
I have downloaded a trail version of Illustrator and it will not open.
-
Flash Menu Showing up Small in Windows
Hello, So I made a site for a friend. Here is the link. Site This site shows up fine nearly everywhere but when she went to visit a gallery that had a PC (not sure what platform) the menu looked tiny, you barely could read it. Today I saw on another
-
Dreamweaver CS4 hangs on spash screen
Hi, When booted in Safe Mode on XP, Dreamweaver CS4 works fine. However opening Dreamweaver when booted in normal mode, causing it to hang at the splash screen. Any idea on finding out what is causing it to hang? Thanks.