IBook will not boot from CD

Disk utility has found problems. Specifically it returned this info:
Verifying volume “Macintosh HD”
Checking HFS Plus volume.
Checking Extents Overflow file.
Checking Catalog file.
Invalid node structure
The volume Macintosh HD needs to be repaired.
Error: The underlying task reported failure on exit
1 HFS volume checked
Volume needs repair
I have tried to restart the iBook using the original restore CD, the original install CD, the Leopard CD, the Tiger CD and Norton Utilities CD. The computer will read the discs but will not boot from them so I can't find a way to repair the effected volume.
Tried Parameter Ram but feel there are deeper problems; just don't know how to get to them.

knateb, Welcome to the discussion area!
Just for the record, your iBook shipped with a version of OS X somewhere between OS 10.4.2 and OS 10.4.4. Therefore it will never boot from a retail Tiger (10.4) disc.
Have you tried resetting the PRAM?
Have you tried resetting the open firmware? The procedure is
Start up into Open Firmware by pressing and holding the Command-Option-O-F key combination during startup.
At the Open Firmware prompt, type: reset-nvram
Press Return.
At the Open Firmware prompt, type: reset-all
Press Return.

Similar Messages

  • IBook will NOT boot from Combo Drive

    Hi all,
    I'm trying to boot from my Tiger install DVD using the usual method - holding down "C" while pressing the power key. The DVD drive never even spins up. All I get is a gray screen with the apple - no spinning bars.
    This occurred after the latest security update trashed all logins on the machine (G4 iBook, 512 MB RAM, 80 GB HD, 10.4.9) Immediately after entering a user password, loginwindow would crash, followed by mdimport, followed by crashserver I could briefly boot using command-S, but that stopped working (blue screen).
    I then booted of the Tiger DVD, ran Disk Utility, Hardware Profiler, and used terminal to do "nvram boot-args="-v". Disk utility showed no permission or disk problems, and the profiler showed everything was there that was supposed to be there.
    Next, I did an archive-and-install. The Tiger DVD passed its verification, the installation appeared to proceed normally, the system rebooted at the end, and up came the gray screen.
    All subsequent boots only came up as far as the gray screen. I reset the parameter ram (alt-command-p-r-power), waiting for three beeps. I then tried to boot off the DVD, and now the machine doesn't even spin the drive up.
    I have also reset the PMU following the directions on the apple knowledge base.
    Is there something I've missed? I do not have another mac to try Target mode. Any suggestions would be welcome!
    TIA,
    dan
    white iBook G4 Mac OS X (10.4.9)

    Another opton is to pop in the disk, restart, holding down the OPTION key, select the disk, and click the lower-right arrow. http://docs.info.apple.com/article.html?artnum=106178 has the details.

  • IBook G3 will not boot from CD/DVD

    Ok, I have an iBook G3.
    I was restoring it to factory with the Software Restore disks which came with the unit as I was planning to move on to a new unit.. But there was a power cut in the middle of the process and the unit shut off. Now, it does not recognise a HD when booting holding option.
    It also will not boot from any CD/DVD other than the Apple HW Test disk provided with the unit.. All other disks spin up and then get ejected, on the odd occasion it does not eject, it boots to a icon of a floppy diskette with a flashing ? (Saying that, I did manage to get it to load from the restore disk 1 once, but it just said it could not mount the image file)
    The HW test disk returns no problems
    I have reset PRAM multiple times, and reset nvram and all in Open Firmware. I have also reset PMU as a last resort, but no luck
    Any ideas?

    Hi, and welcome to Apple Discussions.
    Do you have DiskWarrior, maybe?

  • Mid-2009 MacBook Pro sees internal SATA hard drive, but will not boot from or format

    I inherited a Mid-2009 MacBook Pro (15-inch, 2.53 GHz model) with a very strange issue.
    It first presented itself as not being able to boot from the internal SATA hard drive that came with the computer. Nothing I tried could get it to boot, so I assumed the file system was corrupted beyond repair and booted from a CD to try to format the drive. Disk Utility on the CD would not format the drive, giving me strange error messages like "Unable to write to the last block of the device".
    At this point I figured the drive itself must be toast, so I pulled it out and put another known-good SATA hard drive in, booted from CD, and attempted to format. Again, same error messages and an unsuccesful format.
    So I had the bright idea of formatting one of the drives in an external enclosure and then putting it in the MBP to see if OS X would even install. No dice. Get a cryptic error message before installation even begins.
    So I installed OS X on the drive in the external enclosure and put it in the MBP, and it attempts to boot, but never goes anywhere.
    So to sum up, the symptoms I'm seeing:
    MacBook Pro CAN see internal SATA hard drives.
    MacBook Pro WILL NOT boot from any internal SATA hard drive and cannot format or install OS X to any internal SATA hard drive.
    MacBook Pro WILL boot from any CD or external device and seems to work properly otherwise.
    At this point I'm thinking it's one of two things: the hard drive ribbon cable or the SATA controller on the logic board.
    Since the MacBook Pro seems to work completely fine other than this one issue, and will boot properly from both external devices and the CD (also a SATA device), I'm thinking and hoping that it's just the hard drive ribbon cable. From my searches online, I've heard that this batch of MacBook Pros is known to have issues with the hard drive ribbon cable, but it seems in most cases this manifests itself by the Mac not being able to see a drive at all.
    I've done quite a bit of troubleshooting to get to this point, but right now I'm just looking for any feedback at all. Specifically I'd love to know a way I can easily test to see whether it's the logic board or the cable.

    UPDATE: An interesting development!
    I just tried a third known-good SATA hard drive, one which I believe supports SATA I only (but I'm not sure), and unlike the other drives that the Mac sees but cannot properly interact with, the Mac can't even see this one when I put it inside.
    Frustrating as this may be, I believe I'm actually getting closer to a solution since my symptoms now appear to be closely aligned with people having SATA ribbon cable issues.
    Onward!

  • Will Not Boot from Install Disc  & 4SNS/1/40000000: TG0D - Thermal Sensor?

    *Will Not Boot from Install Disc*
    I used the "option key" approach with the gray start up disk. At first it ejected the start up disk. Then I nudged the disk back in the machine and it showed on the screen as an option. I clicked on the start up disk image and it finally loaded.
    But, it won't accept the start up disk when holding down the "C" key at restart.
    *4SNS/1/40000000: TG0D*
    I did an Apple Hardware Test and received the following diagnostic:
    Version: 3A121
    Test Suite: Extended Test
    Loop Count: 2
    Result: Failed
    Failure code: 4SNS/1/40000000: TG0D
    *Thermal Sensor*
    A search for the failure code 4SNS/1/40000000: TG0D brought up an Apple Discussion topic entry stating: That error code indicates a problem with a thermal sensor. It could be not working or possibly not connected. You will need to take it to Apple for repair.
    Would a thermal sensor have anything to do with it not starting up when holding down the "C" key at restart? What are thermal sensor problem symptoms?
    *User File Folder Opened Up*
    The machine also starts up with my user file folder opened up rather than with a blank screen as it normally should
    I completed a DiskWarrior rebuild on the disk and verify disk shows it is fine.
    Any suggestions on what to do next with these issues?

    The answer was in your post: "You will need to take it to Apple for repair."

  • G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD

    We have a DP 1ghz Quicksilver PowerMac G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD that came with the machine.
    We were in the process of installing 10.4 Tiger before placing it for sale.
    The Mac was originally OSX Server 10.1 that we later converted to a worksation running 10.3 Panther.
    It has 1 GB of memory, 80GB hardrive, 250MB Zip Drive and a Radeon 7500 video card.
    Since this machine only has a CD-R drive and not a DVD-R, we installed Tiger using another Mac via Target Disk Mode. The installation process went well, but when I tried to reboot I got a Kernel Panic right after startup screen with the grey Apple logo.
    On some reboots we get to the blue startup screen, others it stops at the grey Apple logo, others a black box like the a Kernel Panic - but with no text. Twice it went directly into Open Firmware.
    We have done the following during our troubleshooting:
    - Reseat RAM, Video Card, Hard Drive, Zip & CD-R connections
    - Remove RAM 1 stick at a time and reboot
    - Replace RAM with RAM from another working Quicksilver
    - Replace Video Card with one from another working Quicksilver
    - Zap PRAM
    - Reset CUDA switch
    - Unplug the MAC and remove everything (RAM, Battery, etc) for 30 minutes and try to reboot
    - Tried booting from the Macintosh Server G4 Software Restore CD
    - Tried booting from Mac OS X Server CD
    - Tried booting from AppleCare Protection Plan CD with TechTool
    - Tried booting from Diskwarrior CD
    - Tried booting from an external FireWire drive with a disk image of Tiger OS Install
    - Tried booting with the hard drive disconnected
    The Mac WILL boot from the Apple Hardware Test CD and will pass ALL of the extended tests.

    Conventional wisdom says that any Mac that will not boot up from a System/Install CD OS 9 or an Install CD Mac OS X, has a Hardware problem.
    The diagnostic CD is a red herring because it uses a very primitive method of reading the CD, and so does not properly represent the machines general ability to read CDs.
    I would look at the CD drive cables, etc, and see if another drive gives different results.
    You have not mentioned using the Startup Manager (option key at Startup) to do any checking:
    HT1310- Startup Manager: How to select a startup volume

  • IMac will not boot from any mode except Target Disk

    I have an Early 2008 Penryn iMac 24" MB398LL/A running OS X 10.7.4 (see specs below) that will not boot from ANY mode, It also has several strange vertical bars from top to bottom on the screen. They are about 10 px wide, with some pixels empty and looks a bit like a barcode if you squint at it.
    I have tried Safe Boot, Force Boot, DVD Boot, FireWire/USB Boot,  and it always gets to the same point. It gets to the apple screen with the spinning gear and then after about 8 seconds it freezes. The only way it works at all is in Target Disk Mode. It pops right up on my Macbook Pro and I was able to grab all my info!
    I have run Disc Utilities and Tech Tool on it many times from my MBP and it passes every test.
    I reformatted the HD and installed 10.7 again, it still freezes up at the same point. 
    I have tried using Single User mode and every time have had to run /sbin/fsck -fy twice because it always says the disk is ok but it was modified on the first pass.
    I thought maybe it had a bad video card or logic board but and I ran the Apple Hardware Test on many occasions and it always passes. Recently I was told about Loop Mode and just completed running the AHT for just over 30 hours without any errors at all.
    UPDATE...
    Strange Part… I tried installing Mountain Lion in Target Disk Mode and everything went smoothly. When it restarted on its own the lines on the screen were gone for the moment, but the Mac still freezes up on the spinning gear and immediately restarts on its own.  I have run every thing listed above on it and still nothing. Sometimes the lines reappear then in two more starts they are gone.
    I did manage to have it start one time got a copy of the  the error report (its at the bottom too) The Mac ran for at least 30 minutes with no problems, then the screen went crazy a few seconds and it became unresponsive. The mouse moved but that was all it could do. Now my iMac continually restarts itself, I don't have any more ideas, HELP!
    Specs...
    The iMac "Core 2 Duo" 3.06 24-Inch Aluminum (Early 2008/Penryn) features a 3.06 GHz Intel "Core 2 Duo" processor (E8435), with two independent processor "cores" on a single silicon chip, a 6 MB shared level 2 cache, a 1066 MHz system bus, 2 GB of RAM (800 MHz DDR2 SDRAM, PC2-6400), a 500 GB (7200 RPM) Serial ATA hard drive, a vertically-mounted slot-loading DVD±R DL "SuperDrive", NVIDIA GeForce 8800 GS graphics acceleration with 512 MB of GDDR3 memory, a built-in iSight video camera, and built-in stereo speakers underneath the 24" glossy TFT Active Matrix LCD (1920x1200 native) display.
    Error Report…
    Sat Sep  1 17:13:12 2012
    panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
    CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
    RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
    RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
    R8:  0x0000000000000000, R9:  0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
    R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
    RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS:  0x0000000000000008, SS:  0x0000000000000010
    Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0

    Here is the complete error log...
    Sat Sep  1 17:13:12 2012
    panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
    CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
    RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
    RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
    R8:  0x0000000000000000, R9:  0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
    R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
    RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS:  0x0000000000000008, SS:  0x0000000000000010
    Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0
    Backtrace (CPU 0), Frame : Return Address
    0xffffff80602db800 : 0xffffff801a41d5f6
    0xffffff80602db870 : 0xffffff801a4b7b95
    0xffffff80602dba40 : 0xffffff801a4ce4ad
    0xffffff80602dba60 : 0xffffff7f9bab8654
    0xffffff80602dbb60 : 0xffffff7f9baa218c
    0xffffff80602dbbb0 : 0xffffff7f9baa20e2
    0xffffff80602dbbd0 : 0xffffff7f9ba73554
    0xffffff80602dbc00 : 0xffffff7f9aa8d470
    0xffffff80602dbc40 : 0xffffff7f9aa8d3df
    0xffffff80602dbc60 : 0xffffff7f9aa926ec
    0xffffff80602dbcf0 : 0xffffff7f9aa8af20
    0xffffff80602dbd20 : 0xffffff7f9aadacc7
    0xffffff80602dbd70 : 0xffffff801a833b9b
    0xffffff80602dbdc0 : 0xffffff801a862d57
    0xffffff80602dbe30 : 0xffffff801a497cef
    0xffffff80602dbe80 : 0xffffff801a420abd
    0xffffff80602dbeb0 : 0xffffff801a410448
    0xffffff80602dbf00 : 0xffffff801a4195fb
    0xffffff80602dbf70 : 0xffffff801a4a5ad6
    0xffffff80602dbfb0 : 0xffffff801a4ced13
          Kernel Extensions in backtrace:
             com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000->0xffffff7f9aab8fff
                dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
             com.apple.NVDAResman(8.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aad8 000->0xffffff7f9addafff
                dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
                dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
                dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
             com.apple.GeForce(8.0)[4B9BE287-5251-398E-96B0-BB16C9BFB2D9]@0xffffff7f9ba72000 ->0xffffff7f9bb34fff
                dependency: com.apple.NVDAResman(8.0.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aa d8000
                dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
                dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
                dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
    BSD process name corresponding to current thread: WindowServer
    Mac OS version:
    12B19
    Kernel version:
    Darwin Kernel Version 12.1.0: Tue Aug 14 13:29:55 PDT 2012; root:xnu-2050.9.2~1/RELEASE_X86_64
    Kernel UUID: 3005059E-270B-3B9F-940D-7A66C05DDC9D
    Kernel slide:     0x000000001a200000
    Kernel text base: 0xffffff801a400000
    System model name: iMac8,1 (Mac-F227BEC8)
    System uptime in nanoseconds: 26349024446
    last loaded kext at 22534854703: com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2 (addr 0xffffff7f9c489000, size 12288)
    loaded kexts:
    com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2
    com.apple.driver.AppleHDA          2.3.0f2
    com.apple.driver.AppleTyMCEDriver          1.0.2d2
    com.apple.filesystems.autofs          3.0
    com.apple.iokit.IOBluetoothSerialManager          4.0.9f8
    com.apple.iokit.IOBluetoothUSBDFU          4.0.9f8
    com.apple.driver.AppleLPC          1.6.0
    com.apple.driver.AppleMuxControl          3.2.6
    com.apple.driver.AppleBacklight          170.2.3
    com.apple.driver.AppleUpstreamUserClient          3.5.10
    com.apple.driver.AppleMCCSControl          1.0.33
    com.apple.GeForce          8.0.0
    com.apple.driver.AppleSMCPDRC          1.0.0
    com.apple.iokit.IOUserEthernet          1.0.0d1
    com.apple.Dont_Steal_Mac_OS_X          7.0.0
    com.apple.driver.ApplePolicyControl          3.2.6
    com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
    com.apple.driver.AppleIRController          320.15
    com.apple.iokit.SCSITaskUserClient          3.5.1
    com.apple.driver.AppleFileSystemDriver          3.0.1
    com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
    com.apple.BootCache          34
    com.apple.driver.XsanFilter          404
    com.apple.iokit.IOAHCIBlockStorage          2.2.1
    com.apple.driver.AppleFWOHCI          4.9.5
    com.apple.driver.AppleUSBHub          5.1.6
    com.apple.driver.AirPortBrcm43224          600.36.17
    com.apple.iokit.AppleYukon2          3.2.3b1
    com.apple.driver.AppleAHCIPort          2.4.0
    com.apple.driver.AppleIntelPIIXATA          2.5.1
    com.apple.driver.AppleUSBEHCI          5.1.5
    com.apple.driver.AppleUSBUHCI          5.1.5
    com.apple.driver.AppleEFINVRAM          1.6.1
    com.apple.driver.AppleRTC          1.5
    com.apple.driver.AppleHPET          1.7
    com.apple.driver.AppleACPIButtons          1.6
    com.apple.driver.AppleSMBIOS          1.9
    com.apple.driver.AppleACPIEC          1.6
    com.apple.driver.AppleAPIC          1.6
    com.apple.driver.AppleIntelCPUPowerManagementClient          196.0.0
    com.apple.nke.applicationfirewall          4.0.39
    com.apple.security.quarantine          2
    com.apple.driver.AppleIntelCPUPowerManagement          196.0.0
    com.apple.driver.DspFuncLib          2.3.0f2
    com.apple.iokit.IOAudioFamily          1.8.9fc9
    com.apple.kext.OSvKernDSPLib          1.6
    com.apple.kext.triggers          1.0
    com.apple.iokit.IOSerialFamily          10.0.6
    com.apple.driver.AppleSMBusPCI          1.0.10d0
    com.apple.driver.AppleBacklightExpert          1.0.4
    com.apple.driver.AppleSMBusController          1.0.10d0
    com.apple.nvidia.nv50hal          8.0.0
    com.apple.NVDAResman          8.0.0
    com.apple.iokit.IOFireWireIP          2.2.5
    com.apple.driver.AppleHDAController          2.3.0f2
    com.apple.iokit.IOHDAFamily          2.3.0f2
    com.apple.iokit.IOSurface          86.0.2
    com.apple.iokit.IOBluetoothFamily          4.0.9f8
    com.apple.driver.AppleGraphicsControl          3.2.6
    com.apple.iokit.IONDRVSupport          2.3.4
    com.apple.iokit.IOGraphicsFamily          2.3.4
    com.apple.driver.AppleSMC          3.1.3d11
    com.apple.driver.IOPlatformPluginLegacy          1.0.0
    com.apple.driver.IOPlatformPluginFamily          5.2.0d16
    com.apple.iokit.IOUSBHIDDriver          5.0.0
    com.apple.driver.AppleUSBMergeNub          5.1.5
    com.apple.driver.AppleUSBComposite          5.0.0
    com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.5.1
    com.apple.iokit.IOBDStorageFamily          1.7
    com.apple.iokit.IODVDStorageFamily          1.7.1
    com.apple.iokit.IOCDStorageFamily          1.7.1
    com.apple.iokit.IOATAPIProtocolTransport          3.5.0
    com.apple.iokit.IOSCSIArchitectureModelFamily          3.5.1
    com.apple.iokit.IOFireWireFamily          4.5.5
    com.apple.iokit.IOUSBUserClient          5.0.0
    com.apple.iokit.IO80211Family          500.15
    com.apple.iokit.IONetworkingFamily          3.0
    com.apple.iokit.IOAHCIFamily          2.2.0
    com.apple.iokit.IOATAFamily          2.5.1
    com.apple.iokit.IOUSBFamily          5.1.6
    com.apple.driver.AppleEFIRuntime          1.6.1
    com.apple.iokit.IOHIDFamily          1.8.0
    com.apple.iokit.IOSMBusFamily          1.1
    com.apple.security.sandbox          220
    com.apple.kext.AppleMatch          1.0.0d1
    com.apple.security.TMSafetyNet          7
    com.apple.driver.DiskImages          344
    com.apple.iokit.IOStorageFamily          1.8
    com.apple.driver.AppleKeyStore          28.18
    com.apple.driver.AppleACPIPlatform          1.6
    com.apple.iokit.IOPCIFamily          2.7
    com.apple.iokit.IOACPIFamily          1.4
    com.apple.kec.corecrypto          1.0
    Model: iMac8,1, BootROM IM81.00C1.B00, 2 processors, Intel Core 2 Duo, 3.06 GHz, 2 GB, SMC 1.30f1
    Graphics: NVIDIA GeForce 8800 GS, NVIDIA GeForce 8800 GS, PCIe, 512 MB
    Memory Module: BANK 0/DIMM0, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
    Memory Module: BANK 1/DIMM1, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
    AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8C), Broadcom BCM43xx 1.0 (5.10.131.36.16)
    Bluetooth: Version 4.0.9f8 10405, 2 service, 18 devices, 1 incoming serial ports
    Serial ATA Device: WDC WD5000AAKS-40YGA1, 500.11 GB
    Parallel ATA Device: MATSHITADVD-R   UJ-875
    USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd400000 / 2
    USB Device: BRCM2046 Hub, 0x0a5c  (Broadcom Corp.), 0x4500, 0x1a100000 / 2
    USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x820f, 0x1a110000 / 5
    USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x5d100000 / 2
    USB Device: Hub in Apple Extended USB Keyboard, apple_vendor_id, 0x1002, 0x1d100000 / 2
    USB Device: Trackball, 0x046d  (Logitech Inc.), 0xc404, 0x1d120000 / 4
    USB Device: Apple Extended USB Keyboard, apple_vendor_id, 0x0204, 0x1d110000 / 3

  • RE: HP XP Media Center 2005 Ed will not boot from HP System Restore CD's

    RE: HP XP Media Center 2005 Ed will not boot from HP System Restore CD's.
    The following instructions about  the "Code Purple" error FAILED. Error is still present.
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    ***PLAIN ENGLISH QUICK AND EASY FIX FOR ALL SYSTEMS****
    ***Windows 7 code purple or Windows Vista code purple***
    With the code purple error on the screen, press shift+f10 (the shift key and the F10  key (at the top of the keyboard) at the same time) to open a little screen called a  command prompt. (So, you get a little black screen with white text that says something  about your Windows verison first and a little ways down you'll see "C:\>".   It's all  ready for you to start typing.)
    Type the following line, just as you see it here...
    notepad C:\hp\bin\checkdmi\checkdmi.cmd
    so it will look like this
    C:\>notepad C:\hp\bin\checkdmi\checkdmi.cmd
    Press Enter.
    You will see the text for the file listed in a window using a simple text editor.
    Go to the beginning of the text. Press enter to make a space. Type this...
    goto cleanup
    So, whatever comes after, the first line looks like this...
    goto cleanup
    Save the file and exit notepad and restart your PC. You are good to go.
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    RESULT: Same error and problem.
    So, NOW THE SCENARIO IS THIS...[ And A CHALLANGE TO ALL HP Software EXPERTS]
    ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
    1. The PC will not boot the System Restore CD's
    2. The Original OS install and [HP_RECOVERY] disk sector has been severely damaged by
    all of the following:
        A. Massive Virus Infections as shown by Kaspersky Virus Scan and cleaned up.
        B. The user had originally updated the pc to Vista Business Express Upgrade
            (Supplied by HP with the original purchase and warranty).
             (Prior to the upgrade, Media Center was working correctly.)
        C. The original OS product key(XP Media Center Ed. 2005) has been changed by the Vista Business Express upgrade.
        D. The destructve recovery done by PC-Doctor has done user file damage(s).
        E. All software, and possibly hardware could be corrupted & damaged by viruses,
        incomplete recovery, and the unknown failures and conditions.
    To sum up, the system is locked in an unknown state, waiting for expert help.
    (I can allow and manage to let someone diagnose, repair remotely using another OS  i.e.Linux Opensuse 12.1, or XP Home ed if needed.)
    SO IF YOU THINK YOU ARE UP TO THIS CHALLANGE, SEND MESSAGES TO DAVHPForum anytime. Thanks in advance!
    ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

    Hello @DAVHPForum,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I have read your post on how you are not able to boot your computer using the HP system restore CDs, and I would be happy to assist you in this matter!
    If you are not able to recover your system by following the steps in this document, please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
    http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
    I hope this helps!
    Regards
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • PowerPC G5 will not boot (from CD, single-user, verbose...) - is it dead?

    I had posted this in the OSX forum but had a suggestion to post here as well - any suggestions would be greatly appreciated!
    My PowerPC G5 (10.4.11) will not boot. It gets to the grey Apple screen, and then freezes there, no progress dial, and the fan starts racing after a couple of minutes sitting there. Here is what I have tried so far and the results:
    -Will not boot normally - freezes at grey screen
    -Will not boot from CD (DiskWarrior, 10.4 Install disc OR 10.3 Install disc - which came with the G5, each time it freezes at grey screen
    -Will not boot in safe mode - freezes at grey screen
    -Will not get into single-user mode, freezes at "DART-enabled"
    -Will not get into verbose mode, freezes at "DART-enabled"
    -Holding option when starting up allows me to select a drive (hard drive or CD), but then freezes at grey screen when attempting to boot from either drive
    -Option-Command-Shift-Delete does nothing when starting up, again freezes at grey screen
    -Option-Command-P-R does not work - well, maybe it deletes PRAM, but it never even gets to the grey screen, freezes with a blank (black) screen, so that can't be right
    -I CAN get into open firmware & eject cd, cannot boot up from there - it freezes at the grey screen with a circle w/a line through it
    -Attempted to reset NVRAM from Open Firmware, "reset-nvram" and "set-defaults" both were ok, then it froze after "reset-all"
    I have tried everything I could think of and everything I can find - Does anyone have any possible suggestions or ideas for what I can do?
    I had a couple suggestions that it could be RAM, so I'm going to try to run Apple Hardware Test, though if I can't boot from a CD, that will make that very difficult. Any thoughts?

    Hi svman8-
    Did you also reset the SMU?
    One thing known to cure various ills is to replace the battery.
    This may be a helpful link:
    How to reset the SMU on a Power Mac G5 (Late 2004) or Power Mac G5 (Late 2005)
    Luck-
    -DP

  • BIOS update, then will not boot from any drive

    This old laptop, 3000 C200 8922 was acting very clunky when on wireless.
    Downloaded Bios Version 63ET62WW and flashed it into the bios.
    Now, even though I can get to the bios screen, and it shows the hard drive, DVD/CD drive, it will NOT boot from either.
    It will also "see" a usb installed, but will not boot from it.
    I have removed all power and cleared the CMOS several times and I still have nothing. Tried two different hdd's which have been in the machine and same results. 
    HELP!! I should have never messed with it......

    hi k4pew,
    One rule after a BIOS update is to Load optimize deafults after updating.
       Try that go inside BIOS Hit F9 to load defaults then F10 to Save and Exit.
    If not
    Try turning on the computer and start hitting F1 to load the Recovery Menu and see if that will push then Try Reseting the PC.
    If still the same Im afraid that the BIOS needs to be reflashed.
    Im not aware of any flash tool or a your Previous BIOS Version Firmware available for download.
    You can try calling Lenovo Technical Support for any options available for repair.
    Im sorry to hear what happened
    Regards
    Solid Cruver
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Wiped macbook pro will not boot from install DVD

    I recently purchased an older MacBook Pro that came with the OS system wiped but it did have the original Install DVDs.  The computer will not boot from the DVD.  I have booted holding down the C key and nothing happens.  I have booted holding down the Option key and it shows the Install DVD and I select this and nothing happens.
    How do I get it to open up the Utilities from the DVD to install the operating system?

    It could be a problem with the optical drive, but also may be due to the DVD's being for a different model.
    Exactly which MBP do you have, and what serial numbers are on the discs ?.

  • Optical drive trashed and MB Pro will not boot from USB image

    Hello,
    New here but I have searched and tried all I know to get this MBP working right again. My disk drive is trashed and has been for some time now, this is why I have a bootable version of Snow Leopard on an 8G flash drive. When my MBP began acting funny recently and I went to disk utility to verify permissions and the disk. Both failed = must boot from disk to repair, thus my issue. For some reason by MBP will not boot from the usb image I have used previously??? Pressing C or Option during startup does not work. If I press Option, I only get the harddrive option, C yields nothing and the computer boots normally.
    Please!! let me know how / what you would do to resolve this. I don't understand why I have previously been able to boot from this same file on the same drive previously to repair my disk / permissions but cannot do so now. FWIW, I tried placing the file (OSX) on my external HDD to boot from, this did not work either (USB HDD).
    Thank you in advance for your input!!

    It isn't clear what you mean about your HD being trashed or which disk (HD or USB drive) you are trying to repair, but either way you need to start up from your Snow Leopard installer DVD & instead of installing anything go to the Utilities menu & run Disk Utility from there to repair either or both of the disks.

  • I have a mid-2010 27" Quad Core i5 iMac running 10.8.3.  Startup disk recognizes the primary hard drive as a startup volume but will not boot from it.  Have tried zapping PRAM, ran disk utility.  No errors reported  Any thoughts?

    I have a mid-2010 27" Quad Core i5 iMac running 10.8.3.  Startup disk recognizes the primary hard drive as a startup volume but will not boot from it.  Have tried zapping PRAM, ran disk utility.  No errors reported  Any thoughts?

    My bad Eric. The startup preference recognizes the primary as a 10.8.3 startup volume but when u select it the system does not boot. I can only boot from my external backup drive

  • Intel Xserve will NOT boot from hard disk drive

    I have two Intel Xserves 2.0 QC machines
    I have tried to re-install version 10.4.11 OS (don't ask) onto a Hard disk drive that is in a Disk drive caddy and inserted in the machine.
    When booting from The installation DVD media
    The disk is seen by the "Disk Utility" (the disk is partitioned as GUID boot) and the installation proceeds to the disk.
    Once the first pass of the installation is complete and the system reboots, the system shows the folder and ? mark.
    If I boot and hold "ALT" key to view all avaialble boot options the Hard Disk Drive does NOT appear as valid boot disk.
    It does show, the still inserted Installation DVD.
    I CAN boot from an external firewire drive and the Hard disk drive is visible to the OS once logged in.
    I have tried different caddy postions (left, middle and right)
    I have tried bona fide Apple supplied Disk drives
    I have tried various different caddies
    I have tried installing Operating System 10.5.*  and  10.6.8 server
    I have run SMC reset and system reset
    But still I cannot boot off from any Hard Disk Drive inserted in a caddy at the front of the system.
    Has anyone seen this behaviour?
    Is it fixable?
    Do I have replace something like the Hard Disk Drive back plane circuit board? Or even the main logic board?
    I have now run out of ideas and cannot find any help in discussions or just googling.
    ANY help would be very appreciated
    Regards
    Tony

    Antonio Hi !
    QC = Quad core  or  QX as it is written on the "pull out" serial number tab at rear of system
    I have 3 late 2006 Intel xserves
    On my intial posting I declared 2 were 2.0 machines - when I was trying to be concise
    2 of the macines are 2.66 systems and 1 is 2.0 system - all are QX machines
    the 2.0 and 1 of the 2.66 will NOT boot from the ADM and disk inside the system - whereas the other 2.66 system will.
    I have many different Caddies and these have different product/model number labels
    603-9965
    603-9545
    603-9796
    these are marked "intel SATA"
    The 80Gb was only one of the drives tested - I have used Seagate 400Gb 750Gb and 1Tb  -  all of which have been used in systems at one time or another
    and as I said the drives ARE visible once the operating system (either installation DVD or external firewire are booted from) - they are just NOT visible when the system is searching for boot media.
    Thanks for the guide - I will look through that and continue to try and find an answer

  • Hard disk not recognised - will not boot from cd & No FW Target Disk mode

    hi,
    some help would be greatly appreciated.
    Some time ago i was switching internal hard drives around and wound up with a kernel panic of some sort (see my previous posts).
    following on from this I have tried FW target disk mode with no success, and it will not boot from a retail Tiger install disc (this machine has tiger installed (i think!). I can't force a boot from the optical drive and i also can't even force it to eject the disc inside to try another install DVD/CD (I have panther discs lying around also).
    when i start up with the c key nothing happens, but when i start up with the alt/option key i get a closed padlock symbol, password entry field and a "right facing arrow" button.
    anyone got any clues with this? i'm guessing it could either and/or be an internal hard drive ribbon failure (i have swapped internal HDs multiple times in this machine, which can't be good for it) or the familiar PRAM problem (although why would it not boot from an install DVD if this was the case?). I have changed the power supply unit in the past due to having a power cable snap off inside the original one - damage to PRAM caused by this?
    help would be muchly appreciated!
    Jesse

    Hi, Jesse. Remove the hard drive and its cable, then see whether you can start up from a CD or DVD. If that works, replace your hard drive cable.

Maybe you are looking for