IDoc Acknowledgement from SAP PI to SAP R/3 Server

Hi Experts,
I am sending an IDOC from sap r/3 to SAP PI. After receiving the IDoc I need to send back one acknowledgement to the sap r/3 server, without reaching the target side. Could you guys please help me?
Thanks
Dipankar

it can send back an acknowledgement IDoc (ALEAUDIT) back to R/3 system
This configuration works for sending ACK message back to the Source system from the Target System and should not be mistaken to enable PI to generate the ACK and send back to the Source system.
What can be done is include the source system as receiver in the receiver determination (SAP system is both at the source and target....alongwith the existing FILE target service)......configure different ID objects for this Source > PI> Source ACK flow .... map required data in the mapping.....depending on your need you can use the target structure IDOC/ PROXY/ RFC.
Regards,
Abhishek.

Similar Messages

Succesful IDOC acknowledgements from ECC

Dear MDM gurus,
What is the best way to handle acknowledgements from ECC (INTO MDM) for inbound IDOCS from MDM (MDM->XI->ECC).
We want it such that when an IDOC gets posted into ECC succesfully,it should send an acknowledgement signal back to MDM saying that IDOC was received properly.
Thanks.

HI Mugdha,
I have a concern on the Acknowledgement (ALEAUD) Idoc. I have implemented this scenario wherein DEBMAS IDoc is posted from MDM -PI - ECC and ECC sends back the acknowldgement using ALEAUD Idoc.
However, in PI (SXMB_MONI) there is no separate message entry created for this acknowledgment. The ALEAUD acknowldgement message details is attached to the original DEBMAS message which was triggered from MDM - PI - ECC. Due to this, PI interface created is not able to read the acknowledgement message and process it to post/dump the target file onto the MDM Port.
I tried triggering and ALEAUD Idoc manually using PI - RWB which generated a separate message for ALEAUD Idoc in sxmb_moni and then my target file was created in MDM (But this is just a manual way of testing the PI interface).
Can you advice on how this concern can be dealt with?
Thanks in advance,
Elizabeth.

IDoc Packaging from XI/PI to SAP instance - possible?

Hello,
I'm looking for a way to package IDocs into a single tRFC call from XI/PI to a SAP instance, has anyone done something similar previously? So far all I've been able to find are solutions for the IDoc Sender Adapter (SAP to XI/PI).
Messages are sent into PI via the XI protocol one at a time, then mapped and sent to an SAP instance - I do not want to introduce ccBPM into my scenario and we are not at a sufficent SP level to use message packaging. Any ideas?
Many thanks,
- Ian

Hi,
ahh sorry then:) then it's even easier this works in standard with any SP:)
have a look at my blog:
/people/michal.krawczyk2/blog/2005/12/04/xi-idoc-bundling--the-trick-with-the-occurance-change
also described in my book with screenshots:
http://www.sap-press.com/product.cfm?account=&product=H1935
this approach is very easy
Regards,
Michal Krawczyk

Acknowledgement from a BPE fails inside an IDoc to BPE-scenario

Hi,
we have PI/7.0 SPS 10.
My scenario is quite simple: IDOC --> BPE (in XI) --> IDOC back to R3
Everything works good ... besides the acknowledgements.
I'm getting the error message
<SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIAdapter</SAP:Category>
<SAP:Code area="IDOC_ADAPTER">ATTRIBUTE_INV_SND_SERV</SAP:Code>
<SAP:P1>IP_KVVKS_CONTRL</SAP:P1>
<SAP:P2 />
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>Unable to convert the sender service IP_KVVKS_CONTRL to an ALE logical system</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
I know, that the integration process has no logical system - that's true!
I know, that for "normal" IDocs sending from a BPE to SAP/R3, I can use a header mapping to enter a correct logical system.
But how can I do it with acknowledgements. Inside the PE I wanna send a transport acknowledgement back to R3.
Where can I enter a logical system for a BPE?
I tried to enter the logical system in the "adapterspecific ident." of the BPE - but it's not possible to enter a logical system two times (the logical system was already in use).
Afterwards I run the report IDX_NOALE to disable acknowledgements - works fine, but my boss wanna see the acknowledgements
What can I do?
Thank you all!
regards
Wolfgang Hummel

Hi,
There is an option in the Receiver IDOC adapter called,<b> Restore Original Parties For Idoc Acknowledgements</b> . Have not tried this, but I think this option wil be able to help you out.
<i>Restoring Original Partners for Acknowledgments
If you set the relevant indicator, the original partners from the IDoc request message are used for acknowledgments. This means you no longer have to maintain the alternative identifiers (for party conversion) in the Integration Directory.</i>
http://help.sap.com/saphelp_nw04/helpdata/en/96/791c42375d5033e10000000a155106/content.htm
Regards
Bhavesh

Idoc Acknowledgement ALEAUD.ALEAUD01

Experts,
I have scenario like this: File(File system) XI/PIIDOC (R/3 sytem), this scenario works fine as is.
Now, i have to send back an IDOC acknowledgement from R/3 system to XI system. I used the link
[https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/903a0abc-e56e-2910-51a8-9dc616df56eb]
and all configuration is in place. some times it works, n some time it wont.. this is beacuse I make some permutation n combination of changes, in some of the steps mentioned in the URL.. so, I dont know where I am going wrong..
Note: I did read related SDN posts..
your answers are highly appriciated.
Thanks!

Hi Prema,
1. Was the IDOC was created successfully?
-> Check whether IDOC was created correctly using transaction WE05/WE02/BD87. The issue could be due to partner profile setting, port setting or conditioning setting of your ALE distribution model.
2. Was the IDOC was sent successfully?
-> Check whether number of created IDOC using transaction WE05/WE02/BD87 match with the number of IDOC going thru PI? If it is, then the IDOC was NOT created, and you might want to check the background job that runs RBDSTATE using transaction SM36/SM37
3. Was the IDOC stuck in the PI?
-> You might want to check using SXI_MONITOR and try to fix the issue
Regards,
Lim...

How to send application acknowledgement from R/3 system

Hi guys,
How to send application acknowledgement from R/3 system. Ex. we have post one IDoc and check user validations. Suppose date is wrong that means indicate earlier or wrong date but date format is correct. In this situation we need send one acknowledment to sender.
How to find the solution? pls tell anyone.
Regards
Vijay

Hi Vijay,
Plz do perform the following steps:
1) In the Integration Server, call transaction SE38
2) Run program IDX_ALEREQUEST to process IDocs with message type ALEAUD as XI request
message.
3) Now Enter Sender Port, Sender Client,Partner Number, Partner Type, and Partner Rol
4) In Integration Directory, configure the routing of interface
5) Call transaction SXMB_MONI to display the XI message.
Also,
Further in IDX5 as well you will find entry for IDoc ALEAUD.ALEAUD01
Please go through the link
1)Succesful IDOC acknowledgements from ECC
2)https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/903a0abc-e56e-2910-51a8-9dc616df56eb
3)https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/f6d2d790-0201-0010-9382-b50b499b3fbe
After you triggered the IDoc by e.g. tcode: WPMA and IDoc reached FILE system, FILE receiver CC actually is only able to send acknowledgment types SystemErrorAck and AckNotSupported.
This is because:
- IDoc sender adapter requests the following acknowledgments:
SystemAckRequested="false"
SystemErrorAckRequested="true"
ApplicationAckRequested="true"
ApplicationErrorAckRequested="true"
- File receiver adapter that run on the Adapter Engine support system acknowledgments and system error acknowledgments if they are requested by the sender. These acknowledgments are triggered when a message is successfully processed by the adapter or if an error occurs while it is being processed.
If you havent suppressed acknowledgments for IDocs WP_PLU in IDX_NOALE in XI then you will get:
SystemErrorAck when message has not reached the FILE system
AckNotSupported for all others acknowledgement types
QQ) Will this IDOC Ack applicable for this scenario???
Rather not, since FILE adapter does not support any other acknowledgements then system and IDoc adapter does not request other acknowledgements then application + SystemErrorAckRequested.
In sender system your IDoc will be always in status 39 (instead of 03), when acknowledgement is turned on.
This is because:
For SystemErrorAck the corresponding ALEAUD status is 56
For AckNotSupported the corresponding ALEAUD status is 50
Both inbound 56 and 50 statuses end up in 39 for your outbound IDoc in sender system.
Q1) Will this ALEAUD Idoc contains any Message from File System????
In both cases, it will result in status 39 - IDoc is in the target system. So it does not matter.
Q2) Basically what Information will contain this IDOC Ack.
Idoc number from sender system and status 56 or 50 depends on acknowledgement type.
Q3) Do we receive any Info from the Target File System , if we implement this Ack concept??
Nothing useful.
Remember that File Receiver has no way to determine if the written file has been correctly processed by the back-end application. However, if your FILE application can read your WP_PLU message and after successful processing is able to generate any kind of message then you can acknowledge the communications but you will not be able to link original message with the acknowledgement request message.
To do that you need to configure just normal scenario (that will be your new acknowledgement scenario) FILE -> XI -> R/3. Your FILE service will send ALEUAUD Idoc to R/3 system. Your FILE application must take care to generate proper ALEAUD XML message. In order to treat ALEAUD as a request message (not standard acknowledgement) you need to run IDX_ALEREQUEST in SE38 on XI.
Q1) It means if the Idoc not reached to Target File system means we can able to get the System Error Ack to Sender SAP R/3 System. Am i Right????
Supposed you have turned off acks on XI (tcode: se38, IDX_NOALE) for your sender port/client:
You have sent the IDoc and the last status is "03 - Data passed to port OK"
You don't know whether it was even delivered to XI ...
Supposed you have turned on acks on XI (tcode: se38, IDX_NOALE) for your sender port/client.
1)
You send and IDoc and it has been delivered successfully to FILE system.
Adapter Engine creates acknowledgement type: AckNotSupported
In XI you can see Ack Status: AckRequestNotSupported (Acknowledgement not possible). Category: permanent.
XI will send ALEAUD IDoc to R/3 system: status "50 - IDoc is added"
The IDoc status in sender will be "39 - IDoc is in receiving system (ALE service)".
2)
You send and IDoc and it has not been delivered successfully to FILE system. e.g. FILE server is down.
Adapter Engine creates acknowledgement type: SystemErrorAck
In XI you can see Ack Status: Error (Acknowledgement contains system errors). Category: transient.
XI will send ALEAUD IDoc to R/3 system: status "56 - IDoc with errors is added"
The IDoc status in sender will be "39 - IDoc is in receiving system (ALE service)".
So status 39 means only that IDoc reached XI, but you don't know whether it was delivered to FILE system or not.
Q2) And one more thing is Even though we are dealing with the IDOCFile OR FileIDOC we can able to get the ACk of Type System Error Ack only. Am I Right?????
No, "Sender adapters of the Adapter Engine do not request any acknowledgements."
Q3) So the same case( Which we disscused for IDOCFile) is Applicable for FileIDOC also????
No.
Can we able to get the System Error Ack, if the File is not reached to SAP R/3( Target here)
No.
Q4) If Yes to Q3 means,Where this System Error Ack will be seen in File System side???
Do we need to do any extra settings to receive these System Error Ack at File system side??
Not relevant.
Regards,
Vinod.

Handling Idoc acknowledgements

Hi All,
As per the document "How to handle acknowledgements for Idoc" I made all settings and i am able to get acknowledgement in XI.
In the document it was said it is possible to configure ALEAUDIT as request message by executing the report IDX_ALEREQUEST. After doing this i able to get the acknowledgement as separate message, but it get stopped in the inbound queue.
In SMQ2 it is showing error as "sysfail" and in the detail it is showing "exception triggered but was not caught"
As per the document I hope we can receive the acknowledgement in File.
But i am not able to get it in the file.
Kindly help to get the result.
Thank You
Regards
Prakash

Hi,
Try and see the follwoing steps
1) In the Integration Server, call transaction SE38
2) Run program IDX_ALEREQUEST to process IDocs with message type ALEAUD as XI request
message.
3) Now Enter Sender Port, Sender Client,Partner Number, Partner Type, and Partner Rol
4) In Integration Directory, configure the routing of interface
5) Call transaction SXMB_MONI to display the XI message.
Also,
Further in IDX5 as well you will find entry for IDoc ALEAUD.ALEAUD01
Please go through the link
1)Succesful IDOC acknowledgements from ECC
2)https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/903a0abc-e56e-2910-51a8-9dc616df56eb
3)https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/f6d2d790-0201-0010-9382-b50b499b3fbe
Regards,
sangeetha
Edited by: Sangeetha on Mar 26, 2008 9:29 AM
Edited by: Sangeetha on Mar 26, 2008 9:37 AM
Edited by: Sangeetha on Mar 26, 2008 9:52 AM

IDoc Acknowledgement Issue in SAP PI 7.3

We have configured IDoc to IDoc scenario between two ECC system using IDOC_AAE adapter. When we run the RBDSTATE program to trigger ALEAUD IDoc it is getting failed in SM58 in ECC system. But when we configure a separate scenario to transfer ALEAUD IDoc from one ECC to other ECC system usin IDOC_AAE adapter then the ALEAUD IDoc reached in target ECC system. In this case there is no error in SM58 of ECC system.
SM58 Error: Commit fault: ASJ.ejb.005043 (Failed in component: sap.com/com.sap.aii.ad
Regards,
Anurag

Hi Anurag, Hasan,
Check the following OSS Notes, they are both addressed to the error you mentioned (appearing under different circumstances, so you might have to choose the right one):
1719180 Handling of multiple acknowledgements in one ALEAUD IDoc
1729575 Sending IDoc acknowledgements fails because of long text
Regards,
Greg

Suppress Idoc acknowledgement in SAP PI 7.3

Hi Experts,
I need to suppress ALEAUD Idoc acknowledgements in PI. My scenaros is Idoc (ORDRSP) to file pass through.
Aleady entries are maintained for ORDRSP idoc in IDXNOALE table.
in SE16, IDXNOALE--> Selected ORDRSP entry--> change mode --> I have deleted values for NEG and TYPE, when i trigger Idoc from ECC, first time i am not getting acknowledgements but once i trigger automatically NEG value is updating as "X", from next time i am getting acknowledgements.
I have executed IDX_NOALE report in SE38, If i select ORDRSP message type and click on DoNotRequestAcknowledgments, its asking do you want to overwrite for all? if i select yes, all entries are deleted.
Help me to suppress these ALEAUD acknowledgements in SAP PI 7.3.
Attached is the enries i have updated.
Thanks & Regards,
Mohan.

Hi Harish,
I have checked this thread, As i mentioned earlier
I have executed IDX_NOALE report in SE38, If i select ORDRSP message type and click on DoNotRequestAcknowledgments, its asking do you want to overwrite for all? if i select yes, all entries are deleted.
To suppress idoc acknowledgements, do we need to add entries in IDXNOALE table or do we need to delete existing entreis by using report IDX_NOALE?
If i change NEG and TYPE values as empty, first time its working however next time automatically NEG value is updating as "X" due to that i am getting acknowlegement agan in the second time.
I am confused.
Thanks & Regards,
Mohan.

IDOC Ack from BPM to SAP R3 runs into an error

Hi All,
I have a scenario which sends an DEBMAS IDOC to an Integration Process "IP_SPLIT_Site" which process the IDOC and sends it to multiple systems.
When the IDOC is sent from SAP R3 to the receiving Integration Process "IP_SPLIT_Site" in XI, it is processed successfully.
Since the SAP system is expecting an acknowledgement from the receiver of the IDOC, the integration process "IP_SPLIT_Site" tries to send back an acknowledgement for the IDOC which runs into an error because it is not able to convert "IP_SPLIT_Site" into an ALE logical system.
The error displayed is :
Unable to convert the sender service IP_SPLIT_Site to an ALE logical system
Error code : ATTRIBUTE_INV_SND_SERV
I am getting this error in all my scenarios where an IDOC is sent to an Integration Process.
Is there any solution avoid this error?
Thanks & Regards;
Bbnu

Hi Michal
The 1st approach seems to be helpful.
about the 2nd approach if i am sending the Ack through a separate send step in BPM then i suppose it would show the same error "Unable to convert the sender service IP_SPLIT_Site to an ALE logical system".
OR
Do you mean to say that we could send a separate message of type ALEAUD to the SAP system?
for 3rd approach, i wouldn't wanna handle many partner profiles.
Thanks for your reply,
Rgds;
Bbnu

Upload data from legacy system to SAP through ALE IDOC

Hello All,
I have a requirement where i need to upload the data from legacy system to SAP. So i am using ALE IDOC.
In my requirement i need to extend the Standard IDOC. I have extended the IDOC and even found the exit for the updation of the extended fields to SAP. My data would be be placed in the application server.
Can anybody tell me how to retrieve the data and update in the tables for the extended fields.
Could you please provide a sample program for retrieving data for IDOC.
Thanks

Hi,
You can find the sample code in the following link.
Re: calling idoc_input_creditor
Regards
Sajid

IDOC settings from sap r/3 to sap pi7.3

Hi Guru,
actual problem when i am triggering the idoc from ERP,it is trigeering to the abap stack in sap pi.but i am using idoc_aae adapter at sender side,the message is flowing from sap ERP to file but the message is seen in sxmb_moni,but actually it is not seen in moni .
Please if any one have the idoc setting from sap erp to sap pi7.3. and iam using ICO configuration.
Please help me
Regards
Reddy

Hi,
Please go through the below link :
http://wiki.sdn.sap.com/wiki/display/XI/ALE-Idocconfiguration-+%28R3XIFile%29
Also in your software component version please check whether import of IDocs and RFCs are allowed
from your respective ECC system, and check the ECC system parameters are correctlt maintained or not.
Try out once.

Idoc lost from SAP R/3 to XI

Hi experts,
I have the following problem:
sometimes an idoc fired from SAP (not through WE19) does not reach XI (I cannot see it in SXI_MONITOR). I've checked the following facts:
1. SAP R/3 status of the idoc is 03 (direction outbound).
2. SM58 produces no result.
3. IDX5 produces no result for that idoc.
4. 99,9% idocs of the same type fired in the same day work fine.
Resending manually the same Idoc using WE19 gives no problem and the idoc reaches XI.
any idea?
Thanks a lot,
Daniele

You must see this in WE05 or BD87. Just release the idoc and have a look at we05 or bd87 and limit down the time where to search. in sm58 you can only see the idoc ith the system can not log on to the remote system. Did you check sm58 in the target system? did you check bd87 in the target system?

How to upload the data from XML file to SAP database using IDOC

Hi,
I need some steps to upload data from XML format file from other directory to SAP database using IDOC.
how to approch this please if any one knows give me ans
it will be a great help ful to me
Thanks in Advance
Mallik

Thank you vijay,
But i heard that by using this Fun modules, when we are passing IDOC in back ground schedule, so some other depended FM not supporting, so how to approach this and how to avoid this problem.
Have you worked on this before if any one worked on this please help me out
And thank you once again for your valuable information
Best Regards
Mallik

Idoc Scenario from SAP to SAP via PI 7.1o

Q: Two idocs will process from SAP to SAP via SAP-PI 7.1o and generated together.
Requirement :
Sync
2 IDOCs – as we explained our design will require two IDOCs. The first IDOC will be developed by a Z code and the second IDOC is generated by 100% Standard SAP BAPIs and 2 IDOCs send them to PI. Both IDOCs will be generated together by process code in sap and must be moved to PI and later to the receiver client together(SAP). The process can only be 100% completed when both IDOCs will be processed with success in the receiver side. Any one of the IDOC among 2 idoc's failed all the process should stop.
i think that is not possible , PI will not be able to stop successfull IDOC If another IDOC get fails .
Please give me approaches if any chance .
Thanks, Sanakr

Hi Bhavani,
You can use BPM with correlation to achieve this scenario:
Demonstration of ccBPM Scenario: SAP PI 7.1
**************** - BPM Scenario using Fork and correlation
Regards,
Suman

IDoc Acknowledgement from SAP PI to SAP R/3 Server

Similar Messages

Maybe you are looking for