If I set up separate 2.4 and 5GHz networks on my Airport Extreme base station, is it possible to extend just the 5HGz network?

If I set up separate 2.4 and 5GHz networks on my new Airport Extreme base station, is it possible to extend just the 5HGz network with another AirPorrt Extreme that has duel, but not simultanous, frequencies?

Yes, configure the "extending" AirPort Extreme to connect to the 5 GHz network name when you set it up.
Temporarily, locate the extending AirPort Extreme close to the main Extreme for the setup, then move it to the remote location.
But, be advised that it is not easy to extend 5 GHz using wireless. You will almost need to have line-of-sight between the two AirPorts for this to work.

Similar Messages

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

HT4259 How do I set up an Airport Extreme Base Station (v. 7.6.1) to allow wireless network extension?

I have an Airport Extreme Base station (purchased in 2009) and an Airport Express base station (purchased in 2011 - the model that plugs directly into the electrical outlet) (both version 7.6.1 according to the Airport Utility info). I want to use the Airport Express to extend my wireless network. Using Airport utility setup I have a software option on the Airport Express to set it up to extend the network but I do not have an option on the Airport Extreme wireless setup screen that I can check to allow my wireless network to be extended.
All of the documentation I can find on Apple Support states that I should have an option I can check to allow the wireless network to be extended while in the wireles setup section for the Airport Extreme in Airport Utility; but, that check option isn't there. Is this a case of my Airport Extreme base station being too old to offer that option? Incidentally, when I try to select the extend wireless network option on the Airport Express from the Airport Utility wireless setup menu I get an error message (no details - just an error message). The same Airport Express sets up fine if I select join a network (not what I want to do). Am I just dealing with outdated equipment or does anyone have a suggestion? Thanks.

Close AirPort Utility if it is open.
Temporarily, move the Express to the same general area as your AirPort Extreme and power it up and wait a minute.
Hold in the reset button on the Express for 9-10 seconds and then release. Give the Express a full minute to restart to a slow, blinking amber light.
Click the AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear
Click on AirPort Express just below that and AirPort Utility will automatically open
Wait a minute while AirPort Utility analyzes the network and announces that the Express will be configured to "Extend" the AirPort Extreme network.
Enter a device name for the AirPort Express and click Next
Wait another minute to allow the configuration to occur.
When you see the Setup Complete message, click Done.
Now move the Express to a location that is approximately half the distance from the AirPort Extreme and the general area that needs more wireless coverage
Power up the Express and you are all set. Trash those old instructions.

Power Mac G3 Pismo with Airport wireless card in Mac OS X 10.4 won't connect to wireless network with newest Airport Extreme Base Station set at WPA Personal/WPA 2 Personal encryption.

My Power Book G3 Pismo with an Airport wireless card running Mac OS X 10.4.11 will not connect to my new Airport
Extreme Base Station using WPA Personal/WPA 2 Person encryption. The Airport firmware is version 9.52. From
posts I've read online at different places indicates the Airport card should support the WPA encryption. Perhaps the problem
is the Base Station is using a combination setting and the fault is in the base station?
Thanks for any suggestions

Perhaps an inexpensive usb wireless adapter would work as well?
This is probably the simplest way to get the G3 connected to the wireless network.
I'll have to read up on getting an express and using it as a wireless bridge as I am unfamiliar with the concept.
The new AirPort Extreme is broadcasting a wireless signal.
A new AirPort Express could be located close to the G3. The Express will pick up the wireless signal from the AirPort Extreme, then provide an Ethernet connection to the G3 though a short Ethernet cable.
This can work very well......IF.....you keep the G3 at a fixed location, since it will always be connected to the AriPort Express using an Ethernet cable.
I do have an old Linksys Wireless G router. I wonder if that would work?
In theory, yes. But it would have to use much older WEP "security", which is easily cracked in minutes using free tools available on the Internet. So, anyone who really wanted to get on the network could do so. It's an option, but not a very good one.

Several PC and Mac connectivity issues with Airport Extreme Base Station

Hello,
This is not all necessarily airport base station related, but there is some crossover, so I'm posting all of these issues...
Here is the laundry list of things that I can't make work in a home network that contains a PC w/ XP Home, MacBook 1.83 w/ 10.4.7, and Airport Extreme Base Station w/ Modem.
1. Can't see the PC from the Mac.
a. "Connect to server -> Browse" does not find the PC
b. "ipconfig" on PC provides valid looking IP address
c. ping from mac to PC IP address times out
d. Firewall on XP is disabled via control panel
b. Windows file and printer sharing is enabled
2. Can't see mac from PC
a. Windows file sharing enabled on mac
b. Firewall on mac disabled
c. I used \\MacIPAddr\shortusername
d. ping times out
3. Using dial-up to access internet, how do i tell airport to dial using PC?
a. this feature is working fine from mac
b. If already connected (via instruction from mac), can surf the internet fine from PC
c. Is this even possible from the PC?
4. Can't see printer connected to base station from PC
a. See it fine from mac
b. How do i "find" the printer on the PC?
c. Is Bonjour required for this? (I don't have it on the PC yet)
5. Can't see a "shared" printer on the PC from the mac
a. printer is connected directly to PC
b. Mac's add printer wizardry looks like it may "see" the printer, but then it asks for username and password for PC. This is XP home, with no usernames or passwords. Single user. Nothing seems to work in the credentials pop-up dialog.
Any suggestions on any of these issues is very welcome.
Thanks

Is the PC running any kind of internet security or firewall software?
1. Can't see the PC from the Mac.
2. Can't see mac from PC
Sharing files between an XP PC and a Mac running OS 10.4.x
http://www.ifelix.co.uk/tech/3020.html
3. Using dial-up to access internet, how do i tell
airport to dial using PC?
Jon Sevy has a Java Utility for this purpose.
You will need Java in order to run the utility
http://www.java.com
4 . Can't see printer connected to base station from
PC
Printing from a Windows XP PC to a printer attached to an Airport Extreme Base Station or Airport Express
http://www.ifelix.co.uk/tech/1004.html
Printing from a Windows XP PC to a printer attached to an Airport Extreme Base Station or Airport Express using Bonjour
http://www.ifelix.co.uk/tech/1008.html
Problems with finding Printer Driver on Windows XP when using printer connected to Airport Extreme or Express
http://www.ifelix.co.uk/tech/1012.html
5. Can't see a "shared" printer on the PC from the
mac
Printing to a printer on a XP PC from a Mac running 10.4.x
http://www.ifelix.co.uk/tech/3015.html
Printing to a printer on a Mac running 10.4.x from a Windows PC using Bonjour for Windows
http://www.ifelix.co.uk/tech/3014.html
iFelix

Setting up airport extreme card and airport extreme base station

I have an ibook G4 about 3 years old with osx10.4.10 recently installed. I have recently bought an airport extreme card and have also bought an airport extreme base station.
There seems to be a problem with the set up of the card. It does not seem to find any wireless networks at all, including the base station. The base station seems to be working as I went through setting this up with Apple phone support and we managed to do it by connecting the laptop to the base station with an ethernet cable.
I think the problem is with the card. I think I need to reinstall and set up the card again from scratch, but can't figure out how to do this -aiport utility and airport setup assistant don't seem to help here as they take you straight to the stage of setting up a base station. I seem to remember when I originally installed the card for the very first time (before attempting to set up the base station) that it did find other wireless networks, so I don't think there is a physical problem with the card.
Any suggestions on getting the card working appreciated.
Many thanks

Hello bblairlondon. Welcome to the Apple Discussions!
First, verify if OS X "recognizes" the card, by using the System Profiler utility. Select the AirPort Card option under Network in the column on the left. The "Wireless Card Type" should be "AirPort Extreme (nxnnnn, nxnnnn)."
If no card appears, I suggest that you double-check your AirPort Extreme Card installation by using the following Apple Tech article: iBook G4: CIP Instructions
If the card does appear, then try the following ...
Reset the PRAM
o Shut down the computer.
o Turn on the computer.
o Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
o Hold the keys down until the computer restarts and you hear the startup sound for the second time.
o Release the keys.
(ref: Resetting your Mac's PRAM and NVRAM)

Problem consistently printing via new (summer 2011) AIRPORT EXTREME BASE STATION and Brother wireless printer (model HL5370DW). What am I doing wrong?

Thanks in advance for any help you folks can offer. I'm a newb here and will try to offer as much detail as I can about the dilemma at hand.
Scenario: Home network has been recently set up for wireless internet access via NEW Airport Extreme Base Station (purchased September 2011). Units accessing the network include: 2011 Macbook Pro, 2011 Macbook Air, 2007 Macbook, 2009 Macbook Pro, 2 iPhone 3GSs, and a 1st-gen iPad (and a partridge in a pear tree AEBS is configured to run WPA2 encrypted network, as well as a WPA2 guest network. I am attempting to yoke a BROTHER HL5370DW wireless B or G/ ethernet / usb-capable printer to the main network such that any and all units can print wirelessly or its equivalent (i.e., via printer hooked to AEBS through USB hub)
Problem: Despite configuring the Brother printer to recognize the main WPA2 network I created, I am unable to get wireless printing to work. My workaround was to physically connect Brother printer to AEBS via USB, specifically using a Belkin USB hub (after all, I wanted access to usb drives, as well as the printer). This workaround works ONLY SOME OF THE TIME. Generally, after a fresh boot of any computer or after a restart of the AEBS, any given computer will be able to print (i.e., any computer wirelessly connected to the main WPA2 network recognizes the printer). HOWEVER, at random times, printer access is gone (as is access to USB drives connected to AEBS's usb hub). Wireless networks are still up and running when that happens. IS THERE A WAY TO GET THE USB HUB's devices (i.e., printer and usb drives) to ALWAYS REMAIN AVAILABLE AS LONG AS THEY STAY CONNECTED TO THE AEBS? In other words, what accounts for the intermittent loss of the usb peripherals?
Sometimes, I just shut the airport off on whatever computer is having this problem, and the problem goes away. Sometimes, the problem is present across all computers in the house, sometimes only a few are affected. I can ALWAYS see the AEBS in the Airport Utility if the AEBS is connected to the particular computer via ETHERNET CABLE.
My theories:
- true wireless printing (i.e., without usb hub workaround) doesn't work because the N network somehow isn't backwards compatible with the Brother printer, which, i believe, is B/G. Although...isn't Wireless N networking supposed to work with BG devices? I did find a thread (https://discussions.apple.com/thread/2570774?start=0&tstart=0 ) that explains some of the particulars of WPA2 encryption and Wireless B/G issues, but it was beyond my level of comprehension (I'm a psychologist, but not an Apple Genius
- The usb workaround is only intermittently viable because of some flaw in the Airport or Airport Utility that causes dropouts to happen when a Macbook Pro or Air's lid gets closed or one gets opened after having been at a different network (e.g., at my office).
QUESTIONS:
- Should I try to use my old router (7 year old Linksys WRT54G) as an access point and connect the Brother printer to that G-router? How do I do that?
- I wouldn't mind just relying on the usb hub method if I could just insure more consistency (i.e., no random dropouts of peripherals). How could I do this?
Rule out:
- wireless printing works on my printer - it was being recognized back before the AEBS. I had the Linksys router running a WEP network and had the wireless printer talking with no cables to the router and the computers. (I just don't want to revert to using WEP encryption given its lack of security and my trying to protect HiPAA related health information on behalf of patients)
Any help will be greatly appreciated.
Thanks in advance!

13 ASCII characters = 104 (aka 128)-bit WEP
encryption
If turning off WEP works, then you just need to
provide the cameras with the "Equivalent Network Password".
One of the problems with WEP is that the actual
standard relies on a 10 character HEX key for 40bit
WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier, vendors use certain
algorithms to convert simple alphanumeric passwords
(or passphrases) into HEX keys, thus enabling the use
of simple easy to remember WEP password rather than
lengthy HEX keys. The problem is that different
vendors use different algorithms to generate the HEX
key and therefore a ASCII password on an AEBS will be
hashed differently on a non-Apple client and vice
versa.
You may find the following article helpful:
- Apple article, especially the part about
"Third-party client to Airport".
Brilliant idea about trying the system with No encryption on... that DID solve the problem... almost.. once I turned off the encryption option, and restarted the Airport, I got a dialog box showing that the "Base station needs attention" but it didn't indicate WHAT kind of "assistance" it needed. Nonetheless, I closed out of the Airport program only to find that the indicator light, which had been Green, was now, flashing Yellow and I could not connect anything, including my computer. I opened the Airport program again and found the ONLY way I could get the Green light on was to select some sort of encryption option... then the light would go Green again but my cameras would not hook up again, and when I went back in and ONLY changed the option to NO encryption, I got the yellow flashing light and the "this base unit needs attention" warning...
I think your suggestions are almost on the mark... is there any way of reconciling the WEP coding between the cameras and the Airport??? Or turning off the encryption option and STILL have Airport work?
Thanks again for your help and suggestions... I really appreciate it.
geoff

Airport utility no longer recognizes my Airport Extreme Base Station, which had been set up to extend a wifi network

Hi. In November I set up my airport extreme base station (5th generation I believe) to wirelessly extend the wifi network we use at home to see if it would increase download speeds. Before doing that, I did a factory reset of my airport extreme, and the owner of the airport extreme to which the ethernet cable is attached made changes to his network to allow it to be extended. I folllowed all the directions from the apple support pages, and finally got it to work. I could even access a portable hard drive which I attached to the airport extreme base station being used as the extension. Then a week or so ago I noticed that my laptop would no longer connect to my base station. I did not have time to look into it until this week. Airport utility, either on my Mac or iphone no longer recognizes my base station. My mac is running OS X 10.10.1 and my iPhone is running iOS 8.1.2 I have tried both hard, soft and factory resets of my base station to no avail. The only thing that has changed after doing that, is that when I do a soft reset of my base station, a neighbors airport express appears when it never did before. I can't actually connect to it, but it does try. Then after approximately 5 minutes, it disappears from my list.
Today I went and pulled out my OLD AIRPORT EXTREME base station... you know, the one that looks like a space ship and is running wifi 802.1 b/c? airport utility DOES locate and display that, but airport utility returns a message stating that it cannot be set up by this software. I am attaching an image of that.
Thank you,
John
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?

I think the initial problem is that your iPhone was connected to an open network that wasn't yours.
Go to Settings > WiFi and "Forget" the network created by that AirPort Extreme, it's older than dirt. Forget your neighbor's network also.
Perform the equivalent actions with your Mac: System Preferences > Network > Wi-Fi > Advanced... Delete every network that appears, including your own.
Then, connect to your own network on all your devices, after which you ought to be able to use any of them and configure your Extreme without any difficulty. You may need to start over with a "hard reset" on both the main AirPort Extreme and the one extending its network.
Does this have anything to do with the fact that 'Back to My Mac' is probably enabled?
Not exactly, but using iCloud Keychain will populate all your devices with the names of preferred networks that any of them connect to, no matter where they are. I don't know why Apple considers that a beneficial feature.

I have an Apple AirPort Extreme Base Station (Simultanious Dual_Band) (MC340LL/A), and updated the software. After updating no devices can connect via wifi. Any suggestions.

I have an Appl,e AirPort Extreme Base Station (Simultaneous Dual_Band( MC340LL/A. After updating the software, no devices can connect via wifi.

As suggested in another discussion area, (AirPort), I reset the AEBS to factory defaults. On the TV, I went to >Settings>General>Network>Configure Wireless>Wireless Networks. I could then see the generic "Apple Network xxxxx" on the TV. From my MacBookPro, I verified that I could connect to the TV by launching iTunes and noting that the TV was now visible in the "Devices" menu. Went back to the AEBS and ran through the "Setup" routine. I did NOT use the "Previous Settings" but instead, saved the old settings profile, created a new wireless network and new settings profile and enabled WPA2 Personal encryption. I then went back to the TV and went through the "Settings" routine again (as noted above). This time, after entering my WPA2 password, the TV connected to the network and problem was solved. Thanks.

New Mac and Airport Extreme Base Station User - Setup question

Good Morning,
I just received my new MacBook Pro yesterday along with the Airport Extreme Base Station. I was tying to setup the airport extreme but have had no luck. I want to make sure I'm connecting things correctly - make sure I'm not doing something stupid.
I have a cable modem and I previously had a Netgear router. The connection from the cable modem that had previously been connected to my Netgear router - I disconnected it and connected it to the Airport extreme base station instead. And then I plugged it in. Is that all the connecting that I need to do? I get the flashing amber light.
Now I did read a few other threads and it sounds like I may need to install the Airport Utility that came with the base station. So I'll try that when I get home tonight. But I would appreciate any other suggestions - especially whether or not I've connected the airport extreme correctly to my cable modem.
Thanks, Susan
MacBook Pro Mac OS X (10.4)

I want to make sure I'm connecting things correctly
The network configuration should look something like the following:
Cable modem > (Ethernet cable) > [WAN port] AEBSn > (wireless) > MacBook Pro
I have a cable modem and I previously had a Netgear router. The connection from the cable modem that had previously been connected to my Netgear router - I disconnected it and connected it to the Airport extreme base station instead. And then I plugged it in. Is that all the connecting that I need to do? I get the flashing amber light.
Since you changed your network configuration, you should perform a complete power recycle of your network components to allow enough time for them to "synchronize."
Modem/Router Power ReCycling
- Power-off the Cable modem, AirPort Extreme Base Station (AEBSn), & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
- Power-on the Cable modem; Wait at least 30 minutes.
- Power-on the AEBSn; Wait at least 5 minutes.
- Power-on the computer(s)
Now I did read a few other threads and it sounds like I may need to install the Airport Utility that came with the base station.
Yes, you will need this utility to perform the setup and follow-on administration of the AEBSn.

Using Airport Extreme base station as wireless Cable router and airtunes.

Can I replace my wired Roadrunner cable modem with a Apple Airport Extreme wireless 56g router removing the wired modem out of the picture?
I just have read and have not come to the complete conclusion that the Airport extreme base station is a standalone wireless router.
I would like this if it is a wireless standalone router as I want to but a pair of wireless airtunes router for music around the house keeping the Airport Extreme in my room where the airtunes routers would not be as I have the computer in my room and I have iTunes right there and would not need the airtunes routers in my computer room.
Leon.

Can I replace my wired Roadrunner cable modem with a Apple Airport Extreme wireless 56g router removing the wired modem out of the picture?
The AirPort Extreme Base Station (AEBS) does NOT have a built-in DSL/Cable modem. You will still require a Cable modem in order to access your ISP's Internet service.
I just have read and have not come to the complete conclusion that the Airport extreme base station is a standalone wireless router.
The AEBS IS a wireless router, but it is NOT a combination wireless router & cable modem.

Recovering Old Datas on New Drive + Setting Airport Extreme Base Station old and new ones

Hello All,
Situation:
-iMac 24" Alu/2008/2.8 Ghz Intel Core 2 Duo/ 2Go DDR2 SDRAM
-2 Airport Extreme Base Stations mushroom type,
-1 Airport Extreme Capsule Model: A1143
The original 320 Go Hard Drive of my iMac crashed few months ago. A "technician" installed a new Hard Drive 235 Go while trying to recover all datas from old one. Failed.
No back up. The old disc needs to be unlocked in a dustless atmosphere. Quite expensive at the moment.
I decided to install OS X from sratch with the original Install Disc delivered with my iMac.
OS X is 10.5
Once on line I updated all pre-installed softwares. Among which Aiport Utility 5.6.1 today.
Problem:
I would like to get bigger hard drive disc, 1To for example. Does this still exist for this iMac 2008 Alu ?
How can I do to get my iMac again to OS X 10.9 ?. Does this mean I need to buy all intermediate levels again ?
How do I get my softwares (the ones on the original Disc: Pack office, Pages, Numbers, etc ...) back on track again, since my iMac is now more like down to factory level ?
Extending my internet provider from the WiFi router via my 3 Airport Extreme Base Stations: 2 mushroom type that need OS X + Airport Utility softwares at a certain level, while the Capsule might need another level. Right now I tried to set up the 3 of them with this Aiport Utility and though they all recognize the provider network, I can never conclude to extend it with the Base Stations: it drops the case. (WDS trouble which I don't even know what it is, or the Base Station simply desapears from Airport Utility scan, ...)
Thank you all for you attention.
Your comments are welcome especially if you have any knowledge on these various subject.
Can't wait to read your piece of advice.
Lionnel From Paris (France).

me too... i connected my hard drive with all my music but i cannot see any of the music that used to be in my itunes... i checked and its there (when I connect the HD directly to my computer) but not when is plugged into the Airport Extreme... Please help!

Setting up airport extreme base station with Mac and PC

I have an '02 iBook with an airport card installed and an airport extreme base station. my roommate has a PC and has the DSL connection in her room. i want to wirelessly network my iBook via the airport base. how do i do this? (my base was given to me without any manuals/disks etc)

Your Netgear wireless router is your network's base station. Your parent's PC will not be "serving as a base station" - its presence on the network isn't at all relevant to what you want to do.
To connect your G5 to the Netgear wireless router's network - click on your Mac's Airport menu, click on the name of your Netgear wireless router's network (it will appear in the list when you click on the Airport menu), and enter the wireless network password (if applicable) when prompted by the MacOS. That's is - you are connected!

I have an airport extreme base station and have no clue how to set up a private wireless network instead ton open one i have now.

I have an airport extreme base station and have no clue how to change to a pawword type network from the network i have now that is free to the neighbor hood.

Which version of the AirPort Utility are you using?

Connecting Airport Extreme Base Station and HiTron CGN3

A recent installation of Internet/CableTV services by Rogers.ca replaced my Airport Extreme Base Station WiFi network with one based on the Hitron CGN3 Cable Modem/Router. Many of the WiFi enabled evices in the home were switched to the new network without too much hassle. However, my multiple NEST CO/Fire alarms failed to connect and after some hunting I established that the CGN3, although apparently ipv6 'compatible' has this protocol not enabled. There is no input facility in the modem setup to activate the protocol. The importer of the device seems to have chosen to not respond to such tech issues.
It now comes down to either using the CGN3 as a Modem/WiFi server or extending the network to include the Airport Extreme on the CGN3 (don't know how to do that) or vice versa, extending the Airport network to include the CGN3 (don't know how either).
QUESTION:
Does anyone have any idea on how to make the Airport Extreme and HiTron Modem/Router function together since the Extreme has the ipv6 protocol enabled and NEST (and other 'Internet of Things') devices will reconnect, no problem.
More Info:
The only reason for the CGN3 to remain as a WiFi server is its range which seems to cover the required service area with a more powerful, stable signal than the Airport. That is somewhat important since TV services come over the Internet and mobile devices apps available from the Apple store can be used as very capable program guides/selectors and remotes for the HDPVR and secondary HD boxes that feed the TVs, eliminating a remotes collection and associated programming and infra-red transmission hassles. I believe the Cable boxes would accept getting the TV signals from the CGN3 and function commands from the Airport Extreme networks. That remains to be proven. Level 2 Technicians at Rogers and NEST Labs have looked at this and can't access the CGN3's ipv6 function to activate it. They don't know much about the Airport Express.
Second Thought:
On the other hand, a second apple Airport base station would extend the network range to rival the CGN3 and the WiFi function of the CGN3 could be turned off. I tried to connect the two routers by LAN cable but they don't seem to see each other and I don't know enough about network settings to get any further.

Whichever airport you use.. express or extreme doesn't matter much..
It should be setup in bridge mode. Plug an ethernet cable from LAN port on the CGN3 to WAN port on the Apple router.
Go into the airport utility and run through the setup. Don't be too worried if it chooses the wrong setup.. you can go back and edit it after the setup is complete.
You will want to open the Edit.
Then go to the various tabs to ensure it is setup the way you want..
On the Network tab.. bridge mode.
On the wireless tab, create a wireless network.
I recommend you use names that are short, no spaces and pure alphanumeric. eg AEwifi In my case with Time Capsule I use separate wireless names for the two bands. TC24ghz and TC5ghz but that is up to you.. it can make life easier.. then set channels can also make things easier.
Ensure your IPv6 is setup correctly.
The actual internet option will be dhcp.
You will have two wireless networks.. but both will use the CGN3 as router.. the airport if it worked in the past should work. Even if it is not the dhcp server. BUT let me add there is another way to fix this if this setup doesn't work.. please post back your result.. no luck then I will show you how to setup a static IP with the Apple router.

If I set up separate 2.4 and 5GHz networks on my Airport Extreme base station, is it possible to extend just the 5HGz network?

Similar Messages

Maybe you are looking for