Ihave a emac 1002 emc 1955 that igot from a auction,when i turn it on it never gets pass the loading screen and cant get into utilities

i have a emac 1002 emc 1955 that wont go pass loading screen and cant get into utilities,i got from a auction and dont want to take it apart if i dont have to so looking for a little help before it goes that far.thanks

Hi Mike, the Keyboard shouldn't matter, it should be OK in that respect.
Your kind of stuck without any Install Disc to try to repair it or reinstall, but...
Tough without the Install disc, but some things to try...
Does it boot to Single User Mode, CMD+s keys at bootup, if so try...
/sbin/fsck -fy
Repeat until it shows no errors fixed.
(Space between fsck AND -fy important).
Resolve startup issues and perform disk maintenance with Disk Utility and fsck...
http://docs.info.apple.com/article.html?artnum=106214
Tough without the Tiger Disk problems, but try fsck...
To use fsck, you must run it from the command line. Unlike using your mouse to open an application to do something, you'll need to type a text command at the prompt (#) to tell fsck what to do. The Terminal application (/Applications/Utilities) and single-user mode are two examples of command-line interfaces in which you can type such commands. To use fsck:
1. Start up your computer in single-user mode to reach the command line. Hold CMD+s keys down at bootup. Note: If necessary, perform a forced restart as described in the Emergency Troubleshooting Handbook that came with your computer. On desktop computers, you can do this by pressing the reset/interrupt button (if there is one) or holding down the power button for several seconds. On portable computers, simultaneously press the Command-Control-power keys. If your portable computer doesn't restart with this method, you may need to reset the Power Manager.
2. At the command-line prompt, type /sbin/fsck -fy
(SPACE between fsck AND -fy important)
3. Press Return. fsck will go through five "phases" and then return information about your disk's use and fragmentation. Once it finishes, it'll display this message if no issue is found: 
The volume (name_of_volume) appears to be OK  If fsck found issues and has altered, repaired, or fixed anything, it will display this message: ***** FILE SYSTEM WAS MODIFIED *****   Important: If this message appears, repeat the fsck command you typed in step 2 until fsck tells you that your volume appears to be OK (first-pass repairs may uncover additional issues, so this is a normal thing to do).
4. When fsck reports that your volume is OK, type reboot at the prompt and then press Return.
http://docs.info.apple.com/article.html?artnum=106214
Then Safe Boot, (holding Shift key down at bootup), & use Disk Utility from there to Repair Permissions, reboot once more.
Then Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
Does it boot into Open Firmware with CMD+Option+o+f ?
http://docs.info.apple.com/article.html?artnum=42642
reset-nvram (press Enter)
set-defaults (press Enter)
reset-all (press Enter)
Have you done a PRAM reset, CMD+Option+p+r...
http://docs.info.apple.com/article.html?artnum=2238

Similar Messages

TS2570 when i turn on my computer it stays on the grey screen and then turns off by itself. How can I fix that?

when i turn on my computer it stays on the grey screen and then turns off by itself. How can I fix that?

Hi , and a warm welcome to the forums!
Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive & clear caches.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
If 10.7.0 or later...
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.
Hold alt or option key at bootup, do asny boot choices show up?

How to I delete all contact on my iPhone at once. These are contacts ABOVE the contact folder that says From My Mac. I do not want to erase all of the other settings and content from my iPhone -- just the contacts.

How to I delete all contact on my iPhone at once? These are contacts ABOVE the contact folder that says, "From My Mac."
Someone said create a new empty folder on the computer and sync to that -- didn't work .
Another person said, "Reset information in settings to restore to the default." That would erase ALL of the conetent I have on the phone and I do not want to erase all of the other settings and content from my iPhone -- just the contacts.
There has to be a better way than gong through and deleting one-by-one.

Go into Settings...Mail, Calendar and Contacts and siwtch off the Contacts section from the account in question.
The phone should ask you if you want to keep or erase the contacts stored on you phone.
However, if they aren't synched to anything and only exist on your iPhone, you'll have to delete them all one by one

Used ipod nano 3 gen, have a lock that is lock can't get pass the lock how can i get pass the lock

have a used nano Gen. 3 ,and the lock is on after i charge it how do i pass the lock or is it possible. how do i get it out of lock

Yes. Reset network settings. Head to Settings -> General -> Reset and tap Reset Network Settings.
B-rock

I installed an software Update on my MacBook Pro and after that my laptop wont reboot passed the gray screen?

After installing a software update on my Macbook Pro, it would not reboot passed the gray screen and then would shut down.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 8
This step applies only to a Mac Pro tower, not to any other model. A dead logic-board battery can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

I ttunes wants to keep on restoring my phone and I restored a few time now but can not get past the restore screen to load my purchaseed apps etc or sync my phone with new data, it sort of does not recognise the fact that i ihave synced already. Please he

I Tunes wants to conituiosly restore my phone and after every restore it just goes back to the restore screen and i can not get past that to get to my apps etc. It is as if the system does noet regognise the fact that the resotre has been done.................

Follow this very helpful user tip by wjosten:
Syncing to a "New" Computer or replacing a "crashed" Hard Drive

My emac won't get past the grey screen with spinning indicator

before i went to bed last nite it was fine. when i woke up i click on the screen and got the little rainbow ball. that lasted for about 5-10 minutes so i had to push the button. when i try to turn it on now it gets to the grey screen with the spinning indicator but won't get past that. any help would be appreciated

An Archive and Install will preserve you user settings and data. You will need a minimum of 5 GB free on the hard drive to perform an A&I; you can reduce the space required by about 1 GB by selecting the option to install language support only for the language you use (assuming you don't need multiple languages).
However, after seeing your other post (BTW, it'll be easier to keep track if relted issues are in the same thread), you do not want to try an A&I if Disk Utility is reporting anything about 'could not be repaired'. Doing so will would ensure problems down the road, if it worked at all. It's possible for one disk problem to mask another. Whenever Disk Utility (or any other repair utility) reports making repairs, it's good practice to repeat the repair until it reports no problems found or it becomes clear it cannot repair the disk.
DiskWarrior has an excellent track record at repairing problems that Disk Utility cannot (especially Disk Utility versions prior to OS X 10.4.2).
If the drive cannot be repaired, you may be able to keep it by doing an erase install with the write zeros (one pass) option. That will update the hard drive firmware record of bad disk sectors to avoid using. If there are only a few bad sectors, that may let you keep using the hard drive for several more years. An erase install will do just that to your data, through. If you have access to another Mac with either a large amount of free disk space of a DVD burner, you can try using the other Mac as host and the eMac as target in FireWire target disk mode. You can run the host's copy of Disk Utility on the eMac hard drive, and hopefully be able to mount the emac HD so that you can back up the data in your Home directory.

Can any one tell me how can I move to a different folder pictures, that I've cloned, without them staying aggregated? They all come together to the other folder and I don't want that- thanks

Can any one tell me how can I move to a different folder pictures, that I've cloned, without them staying aggregated? They all come together to the other folder and I don't want that… thanks

There's more to it than that.
Folders in Aperture do not hold Images. They hold Projects and Albums. You cannot put an Image in a Folder without putting it in a Project or an Album inside that Folder.
The relationship between Projects and Images is special: every Image must in a Project, and can be in only one Project.
Images can be in as many Albums you want. Putting an Image in an Album does not move it from the Project that holds it.
You can make as many Versions from a Master as you want.
What you want to do may appear simple to you, but it still much adhere to how Aperture works. I still can't tell exactly what you are trying to do (specifically: Images don't live in Folders; moving an Image from a Folder is non-sensical).
It can be very confusing (and frustrating) to get going with Aperture -- but it does work, and can be enormously helpful. If you haven't, take a look at the video tutorials on Apple's Aperture support site.
I feel as though I haven't helped you much -- but we need to be using the same names for interface items in order to get anything done -- and my sense is that you still haven't learned the names of the parts.

HT4623 I just updated my phone to ios6 and it says update completed, just a few ore steps and im done but wont let me go beyond that page when i press continue it just goes back to the ios6 screen "slide to update"???

i just updated my iphone to ios6 and now it wont let me use my phone it says i phone was updated there are just a few more steps then im done but it wont let me get past the first screen it just goes back to the slide to update screen....

If you are absolutely positively sure that the password you are typing in is your Apple ID password, I would try once more to enter the password. Be real careful as you type and make sure that Autocorrect is not changing what you are typing.
If no luck try to proceed without entering the password. If you can get the iPad functional go into
Settings > ITunes and App Store and log in there.
If you can log into to your Apple ID there you will also need to go to
Settings > Messages > Send and Receive and enter or check the email at which you want to receive messages,
Also
Settings > FaceTime > check or enter the email address you want to be reached by FaceTime.

My ipod 5th gen ios 7.0.6 crashed and keeps going from the apple logo, going to a black screen, back to the apple logo, then back to the black screen and so on. Furthermore, my laptop doesn't recognise that the iPod is connected. What do I do?

My ipod 5th gen ios 7.0.6 crashed and keeps going from the apple logo, going to a black screen, back to the apple logo, then back to the black screen and so on. Furthermore, my laptop doesn't recognise that the iPod is connected. What do I do?
Please help me out as this is very irritating. This has been happening for the last 20-30 minutes. It had roughly half battery left.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

After upgrading to Mountain Lion, I repurchased Garageband and I can't get passed the complete installation. I don't seem to have the "com.apple.garageband.plist" file that has been a common solution. Any suggestions?

After upgrading to Mountain Lion, I repurchased Garageband and I can't get passed the complete installation. I've read through several posts that all reference the "com.apple.garageband.plist" solution. I don't seem to have the referenced .plist. Any solutions or suggestions?

Did you upgrade from SnowLeopard?
I can't get passed the complete installation
What exactly is happening? Is GarageBand trying to download over and over again?
all reference the "com.apple.garageband.plist" solution. I don't seem to have the referenced .plist.
The property list stores your preferences, but also the settings from the last run of the application. If that file is corrupted in some way, you might see third behaviour.
You must have this file, for it will be recreated automatically, if it is missing, or you have a permissions problem with your user library.
Perhaps you did look in he wrong place.
in MacOS 10.7. or later the User Library is hidden. To find the Preferences Files use the Finder's "Go" menu:
Quit GarageBand, if it is running.
Click onto you Desktop to bring the Finder forward.
In the Finder Menu press "Go" and hold down the "option/alt" key, until your user library appears in the drop-down menu
Select "Library" and in the Finder window that opens navigate to the "Prederences" folder; move com.apple.garageband.plist to the Desktop.
Log off and on again (don't skip that step!). Retry GarageBand and see if it GarageBand is now downloading the missing content properly.
If that does not fix the problem, post back and explain in more detail what the download problem is.
Why did you "repurchase" GarageBand? If you already owned GarageBand '11, it should be unnecessary.
Regards
Léonie

I have Iphone 4s, and the phone will activate itself again. How do I get changed Apple ID on my phone so that I get using the new username and password that is verified? I would like an answer as soon as possible ... Thank you very much.

I have Iphone 4s, and the phone will activate itself again. This I have verified, but when I shall put this onto my phone, so the phone will not approve the newusername and password. How do I get changed Apple ID on my phone so that I get using the new username and password that is verified? Silly to buy a new phone just for this .... The phone is almost three years old. How long can weexpect this to last? I would like an answer as soon as possible ... Thank you very much.

It sounds like your device might be in Activation Lock. Is it asking your to enter in an Apple ID & password, but only showing you the first letter of the email address and then some dots? Example: j•••••@icloud.com?
If so, do you recognize that email? Do you have an Apple ID that fits the same format? If so, then go to www.cloud.com, log in with that Apple ID & password, and see if under Find My iPhone it shows this device. If so, turn off the device, then remove the device from the list.

I bought the iPad and got it home and when I turned it on, all I see is the iTunes logo w/ a usb connector and arrow. How do I clear that and go to the home screen??? HELP!

i bought the iPad and got it home and when I turned it on, all I see is the iTunes logo w/ a usb connector and arrow. How do I clear that and go to the home screen??? HELP!

You need to Set Up the iPad... Connect it to iTunes...
See here for Getting Started...
http://www.apple.com/support/ipad/
and here...
iPad User Guide iOS 5
http://manuals.info.apple.com/en_US/ipad_user_guide.pdf

I got some books from the itunes store and put them into my library. I created a playlist so that I could burn them to cds. The title is there but no contents. It won't even play the playlist. How do I get the contents of the book?

I got some books from the itunes store and put them into my library. I created a playlist so that I could burn them to cds. It won't even play the book, there are no contents. How do I get the contents of the book?

I'm guessing this is a problem unique to me as there have been no replies at all... Thanks a bunch folks

My Ipod touch is stuck in the password screen and I can't turn it off or cancel. The screen that it is stuck at says :enter the password for the exchange account "exchange"

My Ipod touch is stuck in the password screen and I can't turn it off or cancel. The screen that it is stuck at says :enter the password for the exchange account "exchange"

Try resetting the iPod. Nothing will be lost.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears

Ihave a emac 1002 emc 1955 that igot from a auction,when i turn it on it never gets pass the loading screen and cant get into utilities

Similar Messages

Maybe you are looking for