II can't burn any CD or DVD in my Mac Mini

Hello, I've had my mac mini (super drive) for a week when I tried to burn a data cd I got the error message "Sense Key=Medium error
Sense code=0x0C
Write Error".
After that:"The Drive Reported an Error
Sense Key=illegal Request
Sense Code =0X30,0X05
Cannot write medium,incopatible format
After that i tried to burn a cd in Finder but i had this message:
Disk Unit is not supported.error code"0X80020025
After rebooting i write the cd,but at the second copy i have the same problem
Any ideas of what the problem could be? I suspect the drive has gone bad but I'm not sure how to troubleshoot it. I have tried different types of recordable cd's with the same result. Any help would be appreciated. Desperate!!!
MAC MINI SUPERDRIVE Mac OS X (10.4)

I would take it in to a local mac reseller to test it out with different media. There are different types of blank media to write on with different speeds and specs. You could try buying different brands, but probably cheaper to bring it in. If it's a hardware problem, then they can replace it right there. Good luck.

Similar Messages

I can't burn any DVD or CD - burning process interrupts before it ends

Hi everybody !
Sorry for my bad english, but I assume you're all aware about the frenches are not very good at english.
I've got the following problem: I can't burn any dvd or cd. I've already tried with different programs such as Sonic, Nero 7.0, and I Tunes, and I got every time a mistake wich interrupted the burning process before it ends.
So I don't know what to day ! I've already tried to re install the drivers, but it's didtn't change anything.
In order to help you, I've saved an error log from nero. I hope it could be helpfull to someone who could help me !
Here is the log:
moi
5C82001080000000000666822849
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 02/11/2004 13:54:32
NT-SPTI used
Nero Version: 7.0.0.0
Recorder: <MAT****A DVD-RAM UJ-841S>Version: 1.60 - HA 1 TA 0 - 7.0.0.0
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <MAT****A DVD-RAM UJ-841S >Version: 1.60 - HA 1 TA 0 - 7.0.0.0
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : FUJITSU MHV2100BH PL atapi Port 0 ID 0 DMA: On
CdRomPeripheral : MAT****A DVD-RAM UJ-841S atapi Port 1 ID 0 DMA: On
CdRomPeripheral : AXV CD/DVD-ROM 2.1b axvodka Port 2 ID 0 DMA: Off
=== CDRom-Device-Map ===
MAT****A DVD-RAM UJ-841S D: CDRom0
AXV CD/DVD-ROM F: CDRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 2045MB (2095084kB)
Free physical memory: 1277MB (1308144kB)
Memory in use : 37 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
21.9.2006
CD-ROM (ISO)
21:04:46 #1 Text 0 File Isodoc.cpp, Line 6410
Iso document burn settings
Determine maximum speed : FALSE
Simulate : TRUE
Write : TRUE
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : TAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
21:04:47 #2 Text 0 File Burncd.cpp, Line 3007
MAT****A DVD-RAM UJ-841S
SmoothLink activs
21:04:47 #3 Text 0 File ThreadedTransfer.cpp, Line 525
ReadBuffer-Pipe got 81920KB of Memory
21:04:47 #4 Text 0 File Reader.cpp, Line 124
Reader running
21:04:47 #5 Text 0 File Writer.cpp, Line 113
Writer D: MAT****A DVD-RAM UJ-841S running
21:04:47 #6 ISO9660GEN -11 File Geniso.cpp, Line 3304
First writeable address = 0 (0x00000000)
21:04:47 #7 Text 0 File Burncd.cpp, Line 3301
Turn on Track-At-Once, using CD-R/RW media
21:04:48 #8 Text 0 File DlgWaitCD.cpp, Line 277
Last possible write address on media: 359844 ( 79:59.69)
Last address to be written: 318786 ( 70:52.36)
21:04:48 #9 Text 0 File DlgWaitCD.cpp, Line 289
Write in overburning mode: NO (enabled: CD)
21:04:48 #10 Text 0 File DlgWaitCD.cpp, Line 2568
Recorder: MAT****A DVD-RAM UJ-841S
21:04:48 #11 Text 0 File DlgWaitCD.cpp, Line 456
>>> Protocol of DlgWaitCD activities: <<<
=========================================
21:04:48 #12 Text 0 File ThreadedTransferInterface.cpp, Line 846
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 318787 (318787) = #318787/70:50.37
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 318785 blocks [D: MAT****A DVD-RAM UJ-841S]
21:04:48 #13 Text 0 File ThreadedTransferInterface.cpp, Line 1058
Prepare recorder [D: MAT****A DVD-RAM UJ-841S] for write in TAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc not fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 653182976, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
-150 | lead-in | 0 | 0x41 | 0x00
-150 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
318787 | lead-out | 1 | 0x41 | 0x00
21:04:48 #14 Text 0 File ThreadedTransferInterface.cpp, Line 1126
Removed 2 run-out blocks from end of track 1. Length: 318787 -> 318785.
21:04:48 #15 Text 0 File SCSIPassThrough.cpp, Line 34
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
21:04:48 #16 Phase 24 File dlgbrnst.cpp, Line 1724
Caching of files started
21:04:49 #17 Text 0 File Burncd.cpp, Line 4129
Cache writing successful.
21:04:49 #18 Phase 25 File dlgbrnst.cpp, Line 1724
Caching of files completed
21:04:49 #19 Phase 32 File dlgbrnst.cpp, Line 1724
Simulation started at 24x (3 600 Ko/s)
21:04:49 #20 Text 0 File ThreadedTransferInterface.cpp, Line 2669
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
21:04:49 #21 Text 0 File MMC.cpp, Line 21541
Set BUFE: SmoothLink -> ON
21:10:08 #22 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
21:10:10 #23 Phase 33 File dlgbrnst.cpp, Line 1724
Simulation completed successfully at 24x (3 600 Ko/s)
21:10:11 #24 Phase 36 File dlgbrnst.cpp, Line 1724
Burn process started at 24x (3 600 Ko/s)
21:10:11 #25 Text 0 File ThreadedTransferInterface.cpp, Line 2669
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
21:10:11 #26 Text 0 File MMC.cpp, Line 21541
Set BUFE: SmoothLink -> ON
21:12:16 #27 SPTI -1040 File SCSIPassThrough.cpp, Line 306
CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1040)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x10
Sense Qual: 0x00
CDB Data: 0x2A 00 00 01 76 C0 00 00 20 00 00 00
Sense Area: 0xF1 00 03 00 01 74 5D 0A 00 13 00 00 10
Buffer x03390000: Len x10000
0x72 F1 87 E5 D3 3D 4A 96 F9 B0 73 83 D3 14 72 A1
0xF3 49 6E 93 44 25 04 6D E5 CE 44 5F 3E C6 79 47
0xDD DD EA 3A FD 71 4D 32 CB 35 F3 DF 4B 18 BD 7D
21:12:16 #28 CDR -1040 File Writer.cpp, Line 302
Illegal block size for command
D: MAT****A DVD-RAM UJ-841S
21:12:16 #29 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
21:12:17 #30 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader
21:12:17 #31 CDR -201 File WriterStatus.cpp, Line 200
Invalid write state
D: MAT****A DVD-RAM UJ-841S
21:12:17 #32 TRANSFER -18 File WriterStatus.cpp, Line 200
Could not perform EndTrack
21:12:17 #33 Text 0 File MMC.cpp, Line 16273
<MAT****ADVD-RAM UJ-841S > start Close Session
21:12:30 #34 SPTI -1040 File SCSIPassThrough.cpp, Line 306
CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1040)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x10
Sense Qual: 0x00
CDB Data: 0x00 00 00 00 00 00 00 00 00 00 00 00
Sense Area: 0x71 00 03 00 00 00 00 0A 00 13 00 00 10
21:12:30 #35 CDR -1040 File WriterStatus.cpp, Line 249
Illegal block size for command
D: MAT****A DVD-RAM UJ-841S
21:12:30 #36 TRANSFER -19 File WriterStatus.cpp, Line 249
Could not perform Fixation
21:12:30 #37 Text 0 File WriterStatus.cpp, Line 258
falling back to disc fixation
21:12:30 #38 Text 0 File MMC.cpp, Line 16273
<MAT****ADVD-RAM UJ-841S > start Close Session
21:12:30 #39 SPTI -1046 File SCSIPassThrough.cpp, Line 306
CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1046)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x30
Sense Qual: 0x05
CDB Data: 0x5B 01 02 00 00 00 00 00 00 00 00 00
Sense Area: 0x70 00 05 00 00 00 00 0A 00 AA 00 00 30 05
21:12:30 #40 CDR -1046 File WriterStatus.cpp, Line 249
Illegal disc
D: MAT****A DVD-RAM UJ-841S
21:12:30 #41 TRANSFER -19 File WriterStatus.cpp, Line 249
Could not perform Fixation
21:12:30 #42 Phase 38 File dlgbrnst.cpp, Line 1724
Burn process failed at 24x (3 600 Ko/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 25/04/2005 11:03:00 (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
So, thanks to you !
See you !
Romain

Hi
The error log doesnt provide any very useful information.
According to this error log the simulation was running correct but the burning process was not started.
In such case its very hard to say why it happens. Possibly the drive is damage and cannot calibrate the lens properly or you use not compatible medias.
The burning process depands also on the fiels and data which youwant to burn.
Some data, CD, DVDs are encrypted and its not possible to burn and to copy it.
In other case you could also try to burn the medias with lower speed and not with 24x.
But in worth case you the drive has a malfunction and you have to replace it ;(

Can't burn any DVD on my macbook pro

I can't burn any DVD on my macbook pro, also some of previusly burned DVD are not recognized now & cant be mounted. I tryed choosing different software Burn, KKitchen, Titanium Toast 11, LiquidCD, NTIDragonBurn_v4_OSX, ExpressBurn_i (also burn from Finder) and different brands of DVD -- same diagnostics -- Medium error. One brand (TDK DVD+R) is unstable burn one or two disc tnan begin spoil DVD discs. Have you any solutions?
Model Name:          MacBook Pro
Model Identifier:          MacBookPro8,2
Processor Name:          Intel Core i7
Processor Speed:          2,2 GHz
Number of Processors:          1
Total Number of Cores:          4
L2 Cache (per Core):          256 KB
L3 Cache:          6 MB
Memory:          4 GB
Boot ROM Version:          MBP81.0047.B27
SMC Version (system):          1.69f3
OPTIARC DVD RW AD-5970H:
Firmware Revision:          3APE
Interconnect:          ATAPI
Burn Support:          Yes (Apple Shipping Drive)
Cache:          2048 KB
Reads DVD:          Yes
CD-Write:          -R, -RW
DVD-Write:          -R, -R DL, -RW, +R, +R DL, +RW
Write Strategies:          CD-TAO, CD-SAO, CD-Raw, DVD-DAO
Media:          To show the available burn speeds, insert a disc and choose View > Refresh

Have you read this post? may help you
https://discussions.apple.com/message/18149044#18149044

Can't burn any CD/DVD ?

Hello,
this is my BIG problem :
i have a P965 Neo motherboard + Dual Core E6600 + 2x 1GbDDR2 800 Corsair + 1x Seagate SATA II 320Gb + 1x ASUS DVDRW.
I have BIOS v1.6, and Jmicron v17.08 installed.
In Bios the IDE/RAID control is set to IDE. The IDE busMaster is set to Enabled.
The hard is plugged in SATA 1 ( the blue one).
In control panel the Primary Ide chanel (the hard-disk) is working in UDMA mode 6, and the secondary Ide chanel (the DVDRW) is working in UDMA mode 4.
When i want to burn any CD or DVD with Nero, Roxio or anything else, i have this nice message :
DMA driver error. CRC error. Burn failled. ???
Have someone a clue, because i give up.

Quote from: eftos
In control panel the Primary Ide chanel (the hard-disk) is working in UDMA mode 6, and the secondary Ide chanel (the DVDRW) is working in UDMA mode 4.
When i want to burn any CD or DVD with Nero, Roxio or anything else, i have this nice message :
DMA driver error. CRC error. Burn failled.
Solved !
I change the IDE cable with one of 80 wires.
This is MAGIC !!!
The 80-conductor cable was first defined with the original Ultra DMA modes 0, 1 and 2, covering transfer speeds up to 33.3 MB/s.
The cable is considered "optional" for those modes.
However, for any Ultra DMA modes above mode 2, the 80-conductor cable is mandatory.
cheers

Can i use ANY external CD/DVD drive with the NEW mac mini?

We just got the newest Mac Mini and want to get an external drive for importing and burning CD's and DVD's.
Can we use ANY external CD/DVD drive or do we NEED to use the "Apple MacBook Air SuperDrive."
Thanks
Eliot

Maybe.
I've had some situations where a non-Apple DVD drive would not do a particular job. When I tried the same project with the Apple SuperDrive everything worked perfectly.
This is an area where I would not try to save money.
http://store.apple.com/us/product/MC684ZM/A

Can't burn Verbatim Archival grade DVDs

Hi there! I own a Powermac G5 Dual 2.0 Ghz with Tiger updated and a Pioneer dvd recorder Mod. DVR-110D Firmware ver. 1.37. I can't burn Verbatim Archival grade DVD-R because I always get the following error code: 0x8002006E. It happens with Finder burn and Toast 8 too! Is a solution there to fix this problem? Thanks for your help
Greetings Fabry
Powermac G5 2Ghz Dual Mac OS X (10.4.10)

Hi Fabrizio!
I am particularly interested in your problem because I was about to buy some of those very disks!
In fact, I started this thread some time ago:
http://discussions.apple.com/thread.jspa?messageID=4140243&#4140243
I have been googling the error code, and from a variety of Mac related forums it appears that, as Templeton suggests, it is an incompatibility between the burner and the media.
Some have had the problem with Matshita, some with Pioneer superdrives. Some have had success with exchanging one superdrive for another, some with using different media.
What is strange is that Verbatim DVD-R of the 'regular' kind are the preferred brand here. I have read that F Shippey, who I hope will chip in here if he sees this thread, has tried the Verbatim Archival grade DVDs.
We need a bigger user sample!
Have you tried burning them at only 2x or 4x in Toast?
Do you have any problems burning 'normal' Verbatim DVDs?

Can I burn photos onto a DVD/CD for non-Mac users?

Can I burn photos onto a DVD/CD for non-Mac users?

You can burn a plain CD/DVD by just dragging the photos there; but, that may or may not be playable by everyone. To be sure that the result would be playable in any computer or CD/DVD player, it would be better to use either one of the apps already on your system - such as iPhoto. I don't use that myself - I use other third party software - but take a look at iPhoto help. And, you could make it more interesting by creating a slideshow - also in iPhoto, or iMovie. To give it the final cool touch, bring it into iDVD to give it a polished look if you'd like. You can burn it then from any of the above.
If you happen to have Toast (an excellent burning app), you could use that as well (that is my preferred way to work). In Toast, you have multiple choices: burn a data CD/DVD for Mac only, for Mac & PC, etc, burn a picture CD, video DVD, etc, etc.

Suddenly I can't burn any tunes to disc. I receive an error report - 4280. What's the problem? It all worked fine last week.

Suddenly I can't burn any turnes to disc. I receive an error report - 4280. What's the problem? It was all fine last week.

Additional information:
-also ran "Repair" with new download of iTunes
-am using the same spindle of CDs that worked perfectly a month ago. Tried another brand also to be safe. None worked.
-ran CD/DVD diagnostics within iTunes with Apple Care - no issues apparent
-also tried write-speed 20X on advice of Apple Care (don't know why they thought 20X would be the magic number after the other 3 I tried didn't work)
-tried running itunes in another user account on the computer - same problem, same error code
-Apple suggested it was a copyright issue. I can't even burn music that I created/recorded myself, so that doesn't make sense.
-They thought maybe Quicktime wasn't installed properly, so we checked a film in Windows Media - it played, meaning Quicktime was fine apparently.
Solution:
Unclicked CD text option & Sound Check, ran burn from the File drop down menu (max speed) on a Philips CD-R and it worked! Had been right clicking the playlist name and selecting Burn option from there. That being said, it did not work on 2 other brands prior, with same settings. Not sure why. Just happy it's working again. Is it a brand issue?

If I download a video from my video camera to a new (current 1/12) iMac 21 inch, how can I burn it to a DVD using the computer itself. Is this possible? Do I need to buy additional software. Two salespeople at the Apple were a little confused about this.

If I download a video from my video camera to a new (current 1/12) iMac 21 inch, how can I burn it to a DVD using the computer itself. Is this possible? Do I need to buy additional software. Two salespeople at the Apple were a little confused about this. Thank you.

The DVD recorder I'm referring to is one I've use for years. It is not attached to my aging iMac in any way. I simply play the video from my camcorder (mini-dv tape based Canon HV20) into the DVD recorder and create a DVD that can be played in any DVD player. I can only do minimum editing so what goes in is what I get. This has been fine for creating dupes of the various things I shoot.
If I buy a new iMac (21 inch), I'd like to be able to download the video to the iMac through iMovie, work with it to whatever degree I wish, and burn it to a DVD that can also be played in any DVD player -- or to use as a master to dupe copies.
What I'm understanding from you and others is that this would be possible if Apple had included iDVD in the software that comes with the iMac, or if I purchase the iLife Family Pack, or buy the correct version of Toast. I'm hoping I can persuade Apple to sell me an iMac with iDVD installed.
Essentially I want to move from a basic process of creating DVD copies to the more sophisticated process of creating one from an iMac.
Thank you again for your help and wisdom.

How can I burn a movie to dvd when I don't have iDVD on the new macbook pro?

I have recently purchased a macbook pro and I have made a movie in iMovie, however i don't have iDVD as it no longer comes on macs so how can I burn this movie to DVD without this program? Is there a program already on my laptop or do I need to purchase one and if so what can I purchase?

ToastTitanium from roxio
http://www.roxio.com/enu/products/toast/titanium/overview.html?ClickID=dxsztmmzk 0ookbzn2brmtsr2hcomcnhysxrs

How can I burn a CD or DVD for regular data files?

How can I burn a CD or DVD for regular data files using anything other than itunes?

If you need simple burning, do as Robert said. However, if you need more advanced options, take a look at Roxio Toast 10 Titanium. There is also a Pro HD version if you need more video burning options.

I created a slide show in photoshop elements 10, can i burn it to a dvd or send it to a friend?

i created a slide show in photoshop elements 10, can i burn it to a dvd or send it to a friend?

Share -> Send to iDVD. Only iDVD or similar can create a DVD.
Regards
TD

IMovie does not "share" to iDVD. How can i burn an iMovie to DVD? I do have a copy of iDVD on my Mac

IMovie 11 does not "share" to iDVD. How can i burn an iMovie to DVD? I do have a copy of iDVD on my Mac

My advice, keep iDVD on your Apple Mac as it is a great software and let's hope Apple will introduce it again in imovie 10. Since you may have imovie 10.0 (2013) up-dated from imvovie 9.0 (which included iDVD for burning your home made films on imvoie 9.0,) you can proceed as follows to burn it on a DVD:
a) your film is completed on imovie 10.0. Under share transfer it to "Theatre" (default).
b) open iDVD and drag the film ex "Theatre" on the space "movie" of i.DVD.
c) Inser a DVD and clic on "burn"...
It worked for me.

I keep getting error 4310 and can't burn any cd's

I have no idea why all of a sudden I can't burn any cd's. I continue to get an "error 4310" as it cancels the burn.
It seems this started after upgrading to Windows 8.1 but I am not sure because now I also tried my Windows Media
Player and that won't work either...something about codecs. I am illiterate when it comes to fixing computers but if
there's a simple fix can someone please help.

Hey amyroseofclyde,
Thanks for the question. After reviewing your post, it sounds like the iPhone is not appearing in iTunes. I would recommend that you read this article, it may be able to help you isolate or resolve the issue.
iOS: Device not recognized in iTunes for OS X - Apple Support
Thanks for using Apple Support Communities.
Have a nice day,
Mario

Remote Disc Can't recognize Blank disc, but it does recognize other discs. I am trying to burn something from my itunes on my mac mini to a blank disc on my windows computer. What could be wrong?

Remote Disc Can't recognize Blank disc, but it does recognize other discs. I am trying to burn something from my itunes on my mac mini to a blank disc on my windows computer. What could be wrong?
I can see other discs such as music and stuff so I know I have installed it correctly but how come I can't see the blank disc that I need to burn?

You can't burn discs remotely, you can only read data discs remotely (i.e. you cannot play movie DVDs either).
Either copy the files to the remote computer or get an external drive.

II can't burn any CD or DVD in my Mac Mini

Similar Messages

Maybe you are looking for