Image Recovery for Cisco Aironet 1300 Outdoor Access Point

We purchased two 1300 APs for outside. There is a new release for the image that we wanted to use so, we have the latest security updates. We downloaded, logged onto the access point just fine, but the image never took. After four hours with a direct connection, it was still going and this morning we came in and it just keep rebooting. Our network guy states it looks like a corrupt image. We can barely do anything and since there is no "mode" button like the earlier models, I have not found anything on web sites or forums to help us reload a good image to the access point. I would appreciate any insight someone has and/or where to look for this. I logged on and downloaded about every manual on the 1300 I could find, but have not found a good way to fix this. Not even the upgrade tool will connect since it just keeps rebooting.

Hi Bruce,
Because (as you correctly noted) the 1300 does not have a mode button you could try this method;
Complete the steps in this section in order to reset Cisco IOS Software-based bridges:
If the privileged command prompt ap# is available in the CLI, the write erase command and the reload command erase the startup configuration and reset the unit.
If the GUI is available, choose System Software > System Configuration. Press the Reset to Defaults button.
Aironet 1300 Series Bridges do not have a MODE button to reset the AP to factory defaults. So, if neither the GUI or CLI is available with sufficient privileges, complete these steps to delete the current configuration and return the entire bridge settings to the factory defaults using the CLI.
Open the CLI with a Telnet session or a connection to the bridge console port.
Reboot the bridge by removing and reapplying power.
Allow the bridge to boot until the command prompt appears and the bridge begins to inflate the image.
Press ESC when you see lines that are similar to these on the CLI:
Loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_ja.20040314"
...#############################################################################Note: In order to access the boot loader, you must press ESC twice. But this action depends on the terminal-emulation software that you use.
Messages that are similar to these appear:
Error loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_
ja.20040314"
Interrupt within 5 seconds to abort boot process.
Boot process terminated.
The system is unable to boot automatically. The BOOT environment variable needs to
be set to a bootable image.
C1310 Boot Loader (C1310-BOOT-M), Version 12.2 [BLD-v122_15-ja_throttle.20040314 100]
bridge:At the bridge: prompt, issue the dir flash: command in order to view a directory of the Flash file system.
The directory is similar to this directory:
bridge: dir flash:
Directory of flash:/
2 -rwx 0 env_vars
5 drwx 384 C1310-k9w7-mx.v133_15_JA.20040314
3 -rwx 1128 config.txt
4 -rwx 5 private-config
3693568 bytes available (4047872 bytes used)
bridge:Delete or rename the files config.txt and env_vars, and reboot the bridge.
Note: Do not forget the / character before the filenames.
bridge: delete flash:config.txt
Are you sure you want to delete flash:/config.txt (y/n)?y
File "flash:/config.txt" deleted
bridge: delete flash:/env_vars
Are you sure you want to delete "flash:/env_vars" (y/n)?y
File "flash:/env_vars" deletedIssue the boot command in order to reboot the bridge at the bridge: prompt, or simply power cycle the bridge.
After the bridge reboots, reconfigure the bridge with the web browser interface, the Telnet interface, or Cisco IOS Software commands.
Note: The bridge is configured with the factory default values that include:
The IP address, which is set to receive an IP address with DHCP. If you do not have a DHCP server, you can access the bridge using the default IP address of 10.0.0.1 using HTTP/HTTPS or Telnet. Once you gain access to the bridge via Telnet or GUI, you can modify the IP address of the bridge.
Note: This default IP address of 10.0.0.1 becomes available only for a short period. So, make sure that you assign your own IP address to the bridge within that period of time.
The default username and password, "Cisco".
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_password_recovery09186a00800949d0.shtml#ca_1310_ser
One other thing, be careful with the new IOS that you aren't loading a LWAPP Recovery Image. (it almost sounds like what may have happened)
Hope this helps!
Rob

Similar Messages

  • Cisco aironet 1310 Outdoor access point

    I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
    I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it.  I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS.  I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?
    Thanks for any help you can give.

    Rusty:
    AP supports up to 16 SSIDs to be configured.
    Multiple SSIDs with VLANs configuration is done almost the same way you do with current Aironet APs.
    see here: http://tiny.cc/0qwnkw
    You also need one power injector per AP. Each AP should use it's own power injector.
    The two coaxial output in the power injector both are used to be connected to the AP (see below image).
    The RJ-45 connectors in the power injector one of them is for Console connectivity and the other for network ethernet connectivity.
    Check here: http://tiny.cc/7gxnkw
    HTH
    Amjad
    Rating useful replies is more useful than saying "Thank you"

  • PoE for Cisco 1242AG and 1310G Access Points

    Dear All,
    we purchased a Cisco 1242AG and a 1310G Access Point and in the DataSheet it was specified that these APs support Power-over-Ethernet. The problem is we don't see any RJ-45 port in either AP which could be used for connecting the AP to an PoE Switch. Can you please tell us how we can connect these APs to an 802.11af compatible PowerBridge (by Intermec) ? Thanks.

    Hi Thorsten,
    The 1242 should be good to go but the 1310 is powered quite differently. Have a look;
    AP 1240 Series - Hardware (see diagram)
    http://www.cisco.com/en/US/products/ps6521/products_installation_guide_chapter09186a008079b7f4.html#wp1071972
    Connecting the Ethernet and Power Cables
    http://www.cisco.com/en/US/products/ps6521/products_installation_guide_chapter09186a008079b7f4.html#wp1052781
    1300 Series Power
    Power
    The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
    The power injector is available in two models:
    Cisco Aironet Power Injector LR2 standard version (included with the access point/bridge)
    48-VDC input power
    Uses the 48-VDC power module (included with the access point/bridge)
    Cisco Aironet Power Injector LR2T optional transportation version
    12- to 40-VDC input power
    Note The power injector and the power module must not be placed in an outdoor unprotected environment. The power module must not be placed in a building's environmental air space, such as above a suspended ceiling.
    http://www.cisco.com/en/US/products/ps5861/products_installation_guide_chapter09186a008079b93b.html#wp1051840
    Dual coaxial cable to run from the power injector to the 1300. See attached notes:
    Cisco Aironet 1300 Series
    Cisco Aironet 1300 Series Access Point/Bridge Power Injector
    The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
    Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
    Ethernet Ports
    The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_installation_guide_book09186a00804d3095.html
    AIR-PWRINJ-BLR2
    F-Type Connectors
    Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
    Hope this helps!
    Rob

  • Cisco 802.11n Outdoor Access Point

    I have to propose to a client a 802.11n outdoor Acess point with external antenna, tha gain must be >8 dbi.
    Which cisco model should i use ?

    I have to propose to a client a 802.11n outdoor Acess point with external antenna, tha gain must be >8 dbi.
    DO NOT, under any circumstances, use 1260 or 3500e if you plan to use antennas > 6 dBi.  These two models DO NOT SUPPORT antenna gain higher than 6 dBi.  The only two 802.11n-capable WAP that can support high-gain antenna of > 6 dBi are the 1250 and the 3500p.
    Antenna Product Portfolio for Cisco Aironet 802.11n Access Points
    The 1250 is End-of-Sale (End-of-Sale Date:  12 January 2012) and requires 20.0w of PoE.  The 1250 can support antenna gain > 6 dBi.
    The 3500p was released around mid-2011 because people were howling/screaming about the lack of high-gain antenna support, thus the 3500p was developed alongside the AIR-ANT25137NP-R.
    Cisco recommends that the installation of the AIR-ANT25137NP-R should be done with proper sight-survey.
    [Sorry Scott.  Didn't want to be rude.  ]

  • Configuration of cisco aironet 1260 series access point..??

    i hv a cisco aironet 1262n access point and a normal router(without wlan)  with a broadband connection
    now i want to use my access point as a wifi hotspot 
    but i am not able to access it, through web browser
    i dont know how i connect wires so that i am able to access "  AP access page" and also i forgot its IP address too so can u pls tell me how do i reset it to default 

    Your AP is most likely loaded with a controller-based IOS.  You can easily convert this to autonomous IOS.
    Read this:  Using a TFTP Server to Return to a Previous Release

  • Cisco aironet 1200 Series access point dropping clients

    We are having an issue where our Cisco Aironet 1220 Series AP is constantly dropping clients. We have 3 APs mounted on a single tower, all out of each others range and freq. There are approximatly 30 clients on each AP. We are noticing an increase in dropped customers (up to 20 at a time). ANy suggestions? This only became an issue in the last few weeks, and nothing major has changed.

    Hi
    Even I was facing almost the same kind of problem. But in my case it was wired clients to the workgroup bridge 350.
    I had done lot of testings and reading at that time to resolve this problem.
    However in your case I feel your problem can be resolved by keeping the option "Reliable multicast for Workgroup bridges" disabled in the APs under dot11radio interface settings. This is possibly because the radios cannot associate to more than 20 clients at a time if the option is in the enable mode.
    You need to keep this option enabled in a root bridge when you have problems of dropping the wired clients to the workgroup bridge.
    By keeping this option enabled, you are actually asking the Root bridges to consider the Workgroup bridges as Infrastructure devices and not as clients thereby making the roots to send all the multicasts to the WGBs. However in that case it losses the efficiency of associating more than 20 clients.
    Let me know if this resolves your problem.
    Regards

  • Cisco Aironet 1240 AG Access Point - configure Mac Address using Telnet

    Hi there,
    I’ve got a problem hopefully someone can help me with. I have the above mentioned AP and it is configured, working well and providing wireless access to several laptops on our domain.
    The thing is I can’t get access to the web-based interface to add new laptops Mac addresses to the AP as I currently have them secured with local list Mac address authentication but my user name and password when entered in the web browser login dialog box won’t allow me in although strangely it does allow me to login using the same credentials when I telnet into the AP.
    Does anyone know why I can’t get logged in using the web interface even though the user name and password does appear to be correct as I can telnet in? Also if you have any suggestions how I could sort this without having to perform the password recovery procedure, as I don’t want all the config on the AP wiped and want to avoid having the set the whole thing up again.
    As I workaround if anyone knows what the commands are to allow me to add the Mac addresses of the new laptops so they are added to the local list Mac address authentication list so the new laptops are secured that would be great.
    Thanks in anticipation,
    Tony

    Your AP is probably configured to use the enable secret as the password. Try entering nothing for the username, and enter your enable secret for the password ('Cisco' by default).
    If that doesn't work, post your running-config and we'll be able to see why it's doing that. It's a standard configuration, and no worries because wiping the AP won't be necessary since you can successfully Telnet in.
    Jeff

  • Cisco Aironet 1300 Series Power

    Can the 1310ap receive it's power from a POE switch?

    Hi Edward,
    Sadly the 1310 cannot be powered by PoE ,but, the Power Injector can be up to 100 meters away from the unit.
    Dual coaxial cable to run from the power injector to the 1300. See attached notes:
    Cisco Aironet 1300 Series
    Cisco Aironet 1300 Series Access Point/Bridge Power Injector
    The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
    Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
    Ethernet Ports
    The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
    Power
    The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
    AIR-PWRINJ-BLR2
    F-Type Connectors
    Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
    Hope this helps!
    Rob

  • 1300 Series Access Point/Bridge Power Injector - Using power over ethernet

    Can I use power over ethernet to supply the Injector with power?

    Hi Mikael,
    Sorry, this will not work. Have a look at these specs;
    1300 Series Power
    Power
    The access point/bridge receives inline power from the Cisco Aironet Power Injector (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the access point/bridge. The power injector is an external unit designed for operation in a sheltered environment, such as inside a building or vehicle. The power injector also functions as an Ethernet repeater by connecting to a Category 5 LAN backbone and using the dual-coax cable interface to the access point/bridge.
    The power injector is available in two models:
    Cisco Aironet Power Injector LR2 standard version (included with the access point/bridge)
    48-VDC input power
    Uses the 48-VDC power module (included with the access point/bridge)
    Cisco Aironet Power Injector LR2T optional transportation version
    12- to 40-VDC input power
    Note The power injector and the power module must not be placed in an outdoor unprotected environment. The power module must not be placed in a building's environmental air space, such as above a suspended ceiling.
    http://www.cisco.com/en/US/products/ps5861/products_installation_guide_chapter09186a008079b93b.html#wp1051840
    Dual coaxial cable to run from the power injector to the 1300. See attached notes:
    Cisco Aironet 1300 Series
    Cisco Aironet 1300 Series Access Point/Bridge Power Injector
    The Cisco Aironet 1300 Series Outdoor Access Point/Bridge Power Injector,converts the standard 10/100 BaseT Ethernet interface that is suitable for weather protected areas to a dual F-Type connector interface for coax cables that are more suitable for harsh outdoor environments. The Power Injector also provides power to the outdoor unit over the same cables with a power discover feature and surge protection. To support longer cable runs from your wireless network switch or router, the Power Injector LR is designed to accommodate up to a 100 meter coaxial cable run plus 100 meters of indoor cat5 cable?enabling total cable runs up to 200 meters. The Cisco Aironet 1300 Series Outdoor Access Point/Bridge ships with the Power Injector LR2 and an AC power supply.
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a008022551d.html
    Cisco Aironet 1300 Series Outdoor Access Point/Bridge Hardware Installation Guide
    Ethernet Ports
    The access point/bridge dual-coax Ethernet ports consists of a pair of 75-ohm F-type connectors, linking the unit to your 100BASE-T Ethernet LAN through the power injector. The dual-coax cables are used to send and receive Ethernet data and to supply inline 48-VDC power from the power injector to the access point/bridge.
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_installation_guide_book09186a00804d3095.html
    AIR-PWRINJ-BLR2
    F-Type Connectors
    Dual coaxial cable carries full-duplex Ethernet, DC power, and full-duplex console port (RS-232 connection)
    From this link:
    http://www.cisco.com/en/US/products/ps5861/products_data_sheet09186a00802252e1.html
    Hope this helps!
    Rob

  • Beginner Needs Help with Aironet 1131G Wireless Access Point

    I have a new Cisco Aironet 1131G Wireless Access point.  It is picking up an IP address and I can ping that address.  However, I can't access it via the web-based GUI or the CLI.  I have preformed the reset.  Any suggestions would be greatly appreciated.
    Thanks.

    Hi,
    I cannot access means what?? are you not able to go to CONFIG T prompt from CLI?? and if you are in the same subnet as that of the AP, are you not able to open up the GUI?? if you are not able to then, issue the command "show version" on the AP CLI and see if your image is "RCVKW8" image. if so u need to convert the same to IOS using the below method..
    http://www.cisco.com/en/US/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap22-trouble.html#wp1038660
    lemme know if this answered your question..
    Regards
    Surendra
    ====
    Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

  • Cisco Aironet 1300 QoS

    Hello, I have 2 Cisco Aironet 1300 Bridges which provide data and voice communication between 2 buildings. Up until recently QoS has not been needed, but lately there appears to be congestion due to reports of poor voice quality. Building A houses a V3000 NBX Telephone system, Building B houses approximately 30 remote IP phones. Building A and Building B are approximately 100 yards apart. No VLAN's. Due to myself being an extreme noob to Cisco bridges, I was hoping some of you may have had experience in setting this up and hopefully provide some tips. I need to prioritize traffic on UDP ports 2093-2096 and TCP port 1040. Thank you in advance for any suggestions. My current running config is below:
    Using 1283 out of 32768 bytes
    version 12.3
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname LHS-WeightRoom-WCV
    ip subnet-zero
    aaa new-model
    aaa authentication login default local
    aaa authorization exec default local
    aaa session-id common
    dot11 ssid wcv
    authentication open
    guest-mode
    dot11 ssid wcvcisco
    authentication open
    infrastructure-ssid optional
    username root privilege 15 password 7 0247335A05320A2244
    username Cisco privilege 15 password 7 074E164D403D1C061F
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    ssid wcv
    ssid wcvcisco
    speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
    54.0
    station-role root bridge
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    bridge-group 1
    bridge-group 1 spanning-disabled
    hold-queue 80 in
    interface BVI1
    ip address 10.141.8.6 255.255.254.0
    no ip route-cache
    ip default-gateway 10.141.8.5
    ip http server
    ip http authentication aaa
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    control-plane
    bridge 1 route ip
    line con 0
    line vty 0 4
    end

    Here is the URL for the configuration of Cisco Aironet 1300 QoS. Follow the guide it may help you
    http://www.cisco.com/en/US/docs/wireless/access_point/1300/12.3_4_JA/configuration/guide/o13qos.html

  • Cisco Aironet 1300 series

    Hello,
    i have 2 cisco aironet 1300 series configured as root bridge and non root bridge, i managed to configure them and they are associating only when they adjacent , when i separate them them communication fail , could you please help me to solve this . thx 

    Those are very old bridges. So if they are still functioning okay, do they require external antennas or not and do you have external antennas if they do?
    Antenna Interface 
    • AIR-BR1310G-x-K9 or AIR-LAP1310G-x-K9: Air interface (integrated directional antenna) 
    • AIR-BR1310G-x-K9-R or AIR-LAP1310G-x-K9R: Two RP-TNC type connectors for external antennas 
    -Scott

  • Problème d'installation d'ios cisco aironet 1300

    au fait j'ai un cisco aironet 1300 et je n'arrive pas à installer l'ios par ce que 'il ne me donne pas la main pour gérer. Au lieu de m'afficher root> il m'affiche que bridge: avec des commandes qui ne permettent pas d'installer l'ios.
    Si vous pouvez m'aider à reinstaller lle système
    Merci d'avance

    Salut mamadou, quand tu es au prompt, tu tapes :
    ether_init
    flash_init
    set IP_ADDR 192.168.133.160
    set NETMASK 255.255.255.0
    set DEFAULT_ROUTER 192.168.133.1
    Mets bien en majuscules et remplaces l'adresse IP le masque et la passerelle par ce que tu veux sur ta borne
    puis tape :
    tftp_init
    tar -xtract tftp://192.168.130.222/images/c350-k9w7-tar.122-13.JA1 flash:
    remplaces l'ip par celle de ton serveur tftp, et le fichier image par celui correspondant à ta borne que tu auras avant copié sur ton serveur tftp
    tu vas voir pas mal de logs, appuie sur entrée ou sur la barre d'espace pour faire défiler
    une fois l'extraction terminée tu tapes
    set BOOT flash:/c350-k9w7-mx.122-13.JA1/c350-k9w7-mx.122-13.JA1
    remplaces c350.... par le nom de ton image
    puis tu tapes boot pour booter ta borne
    A++

  • Regarding cisco 1400 and 1500 outdoor access point doubt

    Hi,
    I have a requirement of installing 1400 outdoor access point in bridge mode .
    client has got three remote offices which will be connected through 1400 outdoor access point.
    but i came across about lightweight and autonomous version where i am quite confused.
    which version is available in market especially for 1400
    If i could get information about 1500 also , it would be great help .
    If i want to connect all the remote offices in brigde mode . which will be convinient for me ?
    If I could get any link with datasheet for both the access point seperately, it would be great.

    Hi,
    1500 is for MESH network.. 1400 is for bridging in autonomous mode.. most of the time we use 1400 for bridging between two diffrent sites..
    1400 bridges do not work in LWAPP mode.. its always Autonomous.. where in the 1500 canot work in autonomous as well and needs a WLC..
    here is the datasheets for 1400 and 1500..
    http://www.cisco.com/en/US/partner/prod/collateral/wireless/ps5679/ps5279/ps5285/product_data_sheet09186a008018495c.html
    http://www.cisco.com/en/US/docs/solutions/Enterprise/Mobility/emob41dg/ch8_MESH.html
    lemme know if this answered ur question!!
    Regards
    Surendra

  • Cisco Aironet 1300 - Coverage area

    Hi,
    could you please tell me what is the max coverage area that supports on Cisco Aironet 1300 with integrated antenna (13 dbi).

    Check out the following URLs
    http://www.cisco.com/en/US/products/hw/wireless/ps458/products_tech_note09186a008009459b.shtml
    and
    http://www.cisco.com/en/US/products/ps5861/prod_brochure09186a0080230777.html

Maybe you are looking for

  • Using CLI to enter Mac local list on 1200 Series

    I have a number of 1200 series Ap's that are set up for MAC Authentication based on a local list only. From the GUI these addresses are entered from the Advanced Security Screen. I wnt to find a method for entering them from the CLI but am running in

  • Zen Xtra 60GB error c

    I have problem with creative zen xtra 60GB. i cannot copy music and data from and to player. i try everything what i could. I try clean up, reload os, update even format all. Nothing helped i still cannot copy. Please help me

  • Control Panel LCD Screen is too dark.

    Is there a way to brighten the LCD screen on the control panel? Thanks. This question was solved. View Solution.

  • PR-Release Stretegy

    Hi! While creating the release strretegy of PR and during creation of release group with class. the system prompt the following message & cann't save. " Please check release classes (see long text) Message no. ME492 Diagnosis Here you can assign rele

  • From GL account number to amount

    Hello, May I know if I have a particular GL account number, how can I get the amount posted to that GL account from a particular period using logical database PNP? Thanks a lot! Regards, Anyi