Impossible connecting with wireless network Netgear WNR 2000

I can not log on to my wireless network (Netgear WNR 2000) with my macbook. My other PC:s work fine and connect always. My Macbook only connect after I have restarted the router. When I use my Macbook in other places I can connect with wireless network. What is the problem?

I'm assuming that you're using the right network password! After that, the most common causes of difficulty are:
- The router not set up for DHCP and so cannot allocate an IP address to the MacBook
- The router has "MAC" Address Authentication (a security feature - don't mistake MAC for Mac[intosh]) turned on and the AirPort MAC address isn't in the pass list.
- The default "Automatic" location in System Preferences > Networks has been modified so that it no longer works.
Bob

Similar Messages

Netgear router won't let me connect with a network my new roomates use

I have had this problem before connecting to wireless networks, although not all of them. I just moved in with a friend who gave me the network name and password. Although my powerbook G4 sees her network, it shows an error message when i try to connect with the password. She set up the Netgear (WGT624 v3) router using her DELL and everyone else in the house (using PC's) don't have this problem. I'm wondering if we need to go through what she has set up on her computer, because I must have tried everything on mine! Does anyone know how to solve this problem?

Hi tracie,
thats OK I know how hard wi-fi is to setup, I've spent many hours in the past trying to figure out how to set mine up! Its usually the simplest of things.
Your MAC address or Airport ID (as Apple call it) is a string of a series of 6 two digit numbers/letters separated by a colon e.g. 00:2b:35:18:af:32
This identifies your Airport card on a network & your address can be viewed in System Pref.s/Network, then from the drop down "Show" menu choose "Airport" & then click the Airport tab that appears in the row of buttons & you should see your Airport card's MAC address (Airport ID). But if you cant find that option don't worry about it.
While your in Network Sys Pref click show port config. & drag the Airport entry to the top of the list.
If you do try WEP again, go to router's
Wireless Settings > Wireless network
& insure the Mode is set to "g and b" just incase.
Then > Security Options & click WEP.
Then in > Security Encryption > Authentication type
set to Shared key
Also > Encryption Strength
set 128bit
After that go down to > Security Encryption (WEP) Key
in Passphrase enter your new password & click the Generate button on the right - this will bring up your HEX key in the checked "Key" box below.
write this new generated key down & click Apply & log out.
Now on your PB open the Airport network entry window, change top box from "WEP Password" to "WEP 40/128-bit HEX"
Then enter the generated key you wrote down into the box below, & click ok/join.
Keep 'em crossed & you "should" join.

Can not connect to wireless networks with ipad 2

My ipad used to connect to the wireless net at home and in public areas.
Now all by the sudden it can't "see" the network.
Message: " could not connect to wireless network"
I have tried "everything" also on different networks,
except resetting the modem.
My iPhone works, as do all my other computers.
Modem is Zyxel P2812

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Very poor connection with wifi network with mini iPad.

I recently bought à new mini iPad. The connection with wifi network is lost very often and therefor not Stable. I tried the tips such as forgetting the network and connecting again, but that doesn't help. What can I do?

Do #5.
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Two Issues: Cannot connect to wireless networks; Cannot load certain sites

Hey everybody,
I have a MacBook Pro 15".
In just the past week, I've stumbled upon two sudden problems with my network/internet connectivity.
First, I can no longer connect to wireless networks, be it an infrastructure point or computer-to-computer ad-hoc networks. I'm not really sure why. I installed the latest AirPort Update (4.2.3, according to System Profiler). I also recently installed both iStumbler and KisMac v.21. When I started having issues, I thought that maybe one of these two programs might be the culprit, so I uninstalled both of them but I still have the same problem.
Second, I've had issues with not being able to connect to certain websites. I use both Safari and BonEcho as my browsers. The specific sites seem random:
www.weffriddles.com
www.macrumors.com
images.google.com
sports.yahoo.com
finance.yahoo.com
to list a few.
If you need any diagnostic information, please let me know.
Thanks in advance for any advice/help you can provide!
Tommy H.
MacBook Pro Mac OS X (10.4.9) browsers: Safari, BonEcho/ Airport Driver Version: 4.2.3

If you are trying to connect to a third-party router using WPA or WEP, there is a good chance that your Airport card was broken by Apple's 2007-02 Airport Update. There is no fix, and for many of us, our Macbooks and Macbook Pros are useless for wireless connections until Apple fixes the issue. At this point, Apple seems to be denying that there even is an issue, so we may all be in for a long wait indeed.
See this thread if you have some time:
http://discussions.apple.com/thread.jspa?threadID=883021&tstart=0

[SOLVED]I can't connect to wireless networks.

Hi all, i'm new in the world of Arch Linux but not on the Linux world.
I'm having problems with wireless networks, and i had read all what the wiki says and tried all but nothing worked. I wanna say that wired works perfect.
I think the problem comes from dhcpcd. Because in the begins the problem was that dhcpcd stuck on "Waiting for carrier", i read the wiki and seted the channel on auto but didnt work. Now i cant even connect to a wireless red.
iwconfig wlp2s0 essid "Name"
Nothing happens
Here are some of my list-unit-files:
$ systemctl list-unit-files
dhcpcd.service enabled
[email protected] enabled
[email protected] enabled
[email protected] disabled
netctl-sleep.service disabled
netctl.service disabled
[email protected] static
netctl@wlp2s0\x2dCandy.service enabled
NetworkManager-dispatcher.service enabled
NetworkManager-wait-online.service disabled
NetworkManager.service enabled
nscd.service disabled
[email protected] disabled
[email protected] disabled
wpa_supplicant.service disabled
[email protected] disabled
Here the --failed:
$ systemctl --failed
UNIT LOAD ACTIVE SUB DESCRIPTION
dhcpcd.service loaded failed failed dhcpcd on all interfaces
[email protected] loaded failed failed dhcpcd on enp7s0
[email protected] loaded failed failed dhcpcd on wlp2s0
[email protected] loaded failed failed Automatic wireless network co
[email protected]\x206283.service loaded failed failed Networking for netctl profile
My ip link:
$ ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp7s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT qlen 1000
link/ether 70:71:bc:92:00:1f brd ff:ff:ff:ff:ff:ff
3: wlp2s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT qlen 1000
link/ether 74:f0:6d:3d:ee:f4 brd ff:ff:ff:ff:ff:ff
What aditional info do u need?
Thanx for all guys, i have days trying to solve this problem.
Last edited by Niemand (2013-10-13 18:03:45)

ewaller wrote:Niemand,
Yes that is what I was working toward.
I am worried about one thing, however. I note that you are using an Android phone as your AP. Have you done that successfully with other machines? The reason I ask is some carriers here in the states (*cough*Verizon*cough*) make it as difficult as possible to tether their phones. I know that on my phone, I had to turn on NAT forwarding in the phone to make it work. That required I root the phone.
Yes it works perfect with anothers PCs and with this PC on Windows too. I tried on anothers Networks, D-Link Router, Micronet and others. I tried in a lot of connections but it doesn't work.
DarkCerberus wrote:You should try it with just NetworkManager.service or just netctl.service without the @ symbol - with my knowledge - dhcpcd, netctl and NetworkManager all conflicts together, try disabling the other network services like dhcpcd, netctl, NetworkManager etc. And just use one of them and see what the end result is.
I could't disable the following services:
[email protected]
[email protected]
I tried with:
- sudo systemctl disable [email protected]
- sudo systemctl disable [email protected]
- sudo netctl-auto disable-all
Then, i restarted and try again with:
$sudo iwlist wlan0 scan
$sudo iwconfig wlan0 essid "MOTO..."
$sudo dhcpcd wlan0
$ sudo dhcpcd wlan0
version 6.0.5 starting
wlan0: soliciting an IPv6 router
wlan0: soliciting a DHCP lease
wlan0: offered 192.168.43.17 from 192.168.43.1
wlan0: leased 192.168.43.17 for 43200 seconds
wlan0: adding host route to 192.168.43.17 via 127.0.0.1
wlan0: adding route to 192.168.43.0/24
wlan0: adding default route via 192.168.43.1
forked to background, child pid 700
IT'S WORKS!!
The status of the services are:
$ systemctl list-unit-files
dhcpcd.service disabled
[email protected] enabled
[email protected] enabled
[email protected] disabled
netctl-sleep.service disabled
netctl.service disabled
[email protected] static
netctl@wlp2s0\x2dCandy.service disabled
NetworkManager-dispatcher.service disabled
NetworkManager-wait-online.service disabled
NetworkManager.service disabled
nscd.service disabled
[email protected] disabled
[email protected] disabled
wpa_supplicant.service disabled
[email protected] disabled
Now my ip link is:
$ ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT qlen 1000
link/ether 70:71:bc:92:00:1f brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT qlen 1000
link/ether 74:f0:6d:3d:ee:f4 brd ff:ff:ff:ff:ff:ff
And my iwconfig:
$ iwconfig
eth0 no wireless extensions.
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:"MOTOROLA RAZR i 6283"
Mode:Managed Frequency:2.437 GHz Access Point: E0:75:7D:D0:56:98
Bit Rate=72.2 Mb/s Tx-Power=20 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality=70/70 Signal level=-35 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:1 Invalid misc:22 Missed beacon:0
In the begins i didnt have Ethernet but then i turn on manually eth0 and boths works perfect.
Thanks a lot for all.
[SOLVED]

Hp C4580 printer won't connect to wireless network, but see network is available.

I've sat through quite a few of the threads here with regard to photsmart C4580 printer not connecting to wireless network.
My issues started with a cartridge issue, which I resolved with a new cartridge, but only after trying out different solution offered on HP forum.
Now printer won't connect to my network which it has been connected to for over 2 years with no issues. The wireless network is working perfectly fine and I even printed out a HP photosmart C4500 series connectivity status and in this report printer can see the network I need to connect to.
I've tried downloading various programs from Scan doctor to complete install of all HP programs and even tried installing printer from Windows 7 "add a printer", but none can see this printer.
lastly I was hoping trying to locate IP address for printer which looks like it may help, but report says IP Address "not applicable".
I believe printer, wireless network and PC are working correctly, this there a way to switch printer to online so it can be seen.
Help would be great.

Hello there! Welcome to the forums @Cushionman ,
I noticed your post about the issues you are having with connecting the printer to your network. I am wanting to offer you my suggestion that might help you out!
Click this link and then choose Windows 7, and "Solution two: Manually resolve the issue", and follow the steps from there: The Printer is Not Found During Wireless Network Installation in Windows
Let me know the results
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

[SOLVED]cannot connect to wireless network due to a channel setting

Hello guys, I recently came across a problem with my wireless network.
It was first a system-wide upgrade(adapted from the pacman's log):
[2010-08-22 15:10] Running 'pacman -Syu'
[2010-08-22 15:10] synchronizing package lists
[2010-08-22 15:10] starting full system upgrade
[2010-08-22 16:14] upgraded avahi (0.6.25-3 -> 0.6.27-2)
[2010-08-22 16:14] upgraded nspr (4.8.4-1 -> 4.8.6-1)
[2010-08-22 16:14] upgraded nss (3.12.6-3 -> 3.12.7-1)
[2010-08-22 16:14] upgraded chromium (5.0.375.125-1 -> 5.0.375.127-1)
[2010-08-22 16:14] upgraded curl (7.21.0-1 -> 7.21.1-1)
[2010-08-22 16:14] upgraded freetype2 (2.4.1-1 -> 2.4.2-1)
[2010-08-22 16:14] upgraded gnome-keyring (2.30.3-1 -> 2.30.3-2)
[2010-08-22 16:14] upgraded gstreamer0.10 (0.10.29-1 -> 0.10.30-1)
[2010-08-22 16:14] upgraded orc (0.4.6-1 -> 0.4.7-1)
[2010-08-22 16:14] upgraded udev (160-1 -> 161-1)
[2010-08-22 16:14] upgraded gstreamer0.10-base (0.10.29-1 -> 0.10.30-1)
[2010-08-22 16:14] upgraded gstreamer0.10-base-plugins (0.10.29-1 -> 0.10.30-1)
[2010-08-22 16:14] upgraded k3b (2.0.0-2 -> 2.0.1-2)
[2010-08-22 16:14] upgraded linux-firmware (20100623-2 -> 20100807-1)
[2010-08-22 16:14] >>> Updating module dependencies. Please wait ...
[2010-08-22 16:14] >>> MKINITCPIO SETUP
[2010-08-22 16:14] >>> ----------------
[2010-08-22 16:14] >>> If you use LVM2, Encrypted root or software RAID,
[2010-08-22 16:14] >>> Ensure you enable support in /etc/mkinitcpio.conf .
[2010-08-22 16:14] >>> More information about mkinitcpio setup can be found here:
[2010-08-22 16:14] >>> http://wiki.archlinux.org/index.php/Mkinitcpio
[2010-08-22 16:14]
[2010-08-22 16:14] >>> Generating initial ramdisk, using mkinitcpio. Please wait...
[2010-08-22 16:14] ==> Building image "default"
[2010-08-22 16:14] ==> Running command: /sbin/mkinitcpio -k 2.6.35-ARCH -c /etc/mkinitcpio.conf -g /boot/kernel26.img
[2010-08-22 16:14] :: Begin build
[2010-08-22 16:14] :: Parsing hook [base]
[2010-08-22 16:14] :: Parsing hook [udev]
[2010-08-22 16:14] :: Parsing hook [autodetect]
[2010-08-22 16:14] :: Parsing hook [pata]
[2010-08-22 16:14] :: Parsing hook [scsi]
[2010-08-22 16:14] :: Parsing hook [sata]
[2010-08-22 16:14] :: Parsing hook [usbinput]
[2010-08-22 16:14] :: Parsing hook [keymap]
[2010-08-22 16:15] :: Parsing hook [encrypt]
[2010-08-22 16:15] :: Parsing hook [lvm2]
[2010-08-22 16:15] :: Parsing hook [filesystems]
[2010-08-22 16:15] :: Generating module dependencies
[2010-08-22 16:15] :: Generating image '/boot/kernel26.img'...SUCCESS
[2010-08-22 16:15] ==> SUCCESS
[2010-08-22 16:15] ==> Building image "fallback"
[2010-08-22 16:15] ==> Running command: /sbin/mkinitcpio -k 2.6.35-ARCH -c /etc/mkinitcpio.conf -g /boot/kernel26-fallback.img -S autodetect
[2010-08-22 16:15] :: Begin build
[2010-08-22 16:15] :: Parsing hook [base]
[2010-08-22 16:15] :: Parsing hook [udev]
[2010-08-22 16:15] :: Parsing hook [pata]
[2010-08-22 16:15] :: Parsing hook [scsi]
[2010-08-22 16:15] :: Parsing hook [sata]
[2010-08-22 16:15] :: Parsing hook [usbinput]
[2010-08-22 16:15] :: Parsing hook [keymap]
[2010-08-22 16:15] :: Parsing hook [encrypt]
[2010-08-22 16:15] :: Parsing hook [lvm2]
[2010-08-22 16:15] :: Parsing hook [filesystems]
[2010-08-22 16:16] :: Generating module dependencies
[2010-08-22 16:16] :: Generating image '/boot/kernel26-fallback.img'...SUCCESS
[2010-08-22 16:16] ==> SUCCESS
[2010-08-22 16:16] upgraded kernel26 (2.6.34.3-1 -> 2.6.35.2-1)
[2010-08-22 16:16] upgraded kernel26-headers (2.6.34.3-1 -> 2.6.35.2-1)
[2010-08-22 16:16] upgraded libdatrie (0.2.3-1 -> 0.2.4-1)
[2010-08-22 16:16] upgraded libgnome-keyring (2.30.1-1 -> 2.30.1-2)
[2010-08-22 16:16] upgraded libpciaccess (0.11.0-1 -> 0.12.0-1)
[2010-08-22 16:16] upgraded libxvmc (1.0.5-1 -> 1.0.6-1)
[2010-08-22 16:16] upgraded mdadm (3.1.2-2 -> 3.1.3-1)
[2010-08-22 16:16] upgraded pixman (0.18.2-1 -> 0.18.4-1)
[2010-08-22 16:16] upgraded poppler-data (0.4.2-1 -> 0.4.3-1)
[2010-08-22 16:16] upgraded powertop (1.11-2 -> 1.13-2)
[2010-08-22 16:16] upgraded pycairo (1.8.8-1 -> 1.8.10-1)
[2010-08-22 16:16] upgraded pygtk (2.17.0-1 -> 2.17.0-2)
[2010-08-22 16:16] upgraded qimageblitz (0.0.5-1 -> 0.0.6-1)
[2010-08-22 16:16] upgraded usbutils (0.87-1 -> 0.90-1)
[2010-08-22 16:16] upgraded vlc (1.1.2-2 -> 1.1.3-1)
[2010-08-22 16:16] upgraded xextproto (7.1.1-1 -> 7.1.2-1)
[2010-08-22 16:16] upgraded xf86-input-evdev (2.4.0-1 -> 2.4.0-2)
[2010-08-22 16:16] upgraded xproto (7.0.17-1 -> 7.0.18-1)
Then after a reboot, I wouldn't be able to connect to wireless network anymore.
I tried "netcfg Wireless_Archer(my wireless profile's name)" as usual, it replied:
[root@mzws log]# netcfg Wireless_Archer
:: Wireless_Archer up [BUSY]
> WPA Authentication/Association Failed
[FAIL]
Next I tried to bing the network up manually. I followed the "Wireless Setup" and "WPA supplicant" wiki, then I get a timed out problem:
[root@mzws ~]# ifconfig wlan0 up
[root@mzws ~]# iwlist wlan0 scan
wlan0 Scan completed :
Cell 01 - Address: D8:5D:4C:59:52:EC
Channel:13
Frequency:2.472 GHz (Channel 13)
Quality=66/70 Signal level=-44 dBm
Encryption key:on
ESSID:"Archer"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
12 Mb/s; 24 Mb/s; 36 Mb/s
Bit Rates:9 Mb/s; 18 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=000000000bf666fe
Extra: Last beacon: 70ms ago
IE: Unknown: 0006417263686572
IE: Unknown: 010882848B960C183048
IE: Unknown: 03010D
IE: Unknown: 2A0100
IE: Unknown: 32041224606C
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
Preauthentication Supported
IE: Unknown: DD0900037F01010008FF7F
IE: Unknown: DD1A00037F0301000000D85D4C5952ECDA5D4C5952EC64002C010808
Cell 02 - Address: 00:22:B0:8C:76:D7
Channel:1
Frequency:2.412 GHz (Channel 1)
Quality=22/70 Signal level=-88 dBm
Encryption key:on
ESSID:"szpatrick"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s
18 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 12 Mb/s; 24 Mb/s; 48 Mb/s
Mode:Unknown/bug
Extra:tsf=000000e93e5b9174
Extra: Last beacon: 1340ms ago
IE: Unknown: 0009737A7061747269636B
IE: Unknown: 010882848B961224486C
IE: Unknown: 030101
IE: Unknown: 32040C183060
IE: Unknown: 0706474220010D10
IE: Unknown: 33082001020304050607
IE: Unknown: 33082105060708090A0B
IE: Unknown: DD050050F20500
IE: Unknown: DD0E0050F204104A0001101044000102
IE: Unknown: 050400010000
IE: Unknown: 2A0100
IE: Unknown: 2D1A6E1013FFFF0000010000000000000000000000000C0000000000
IE: Unknown: 3D1601050100000000000000000000000000000000000000
IE: Unknown: 7F0101
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : CCMP TKIP
Authentication Suites (1) : PSK
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : CCMP TKIP
Authentication Suites (1) : PSK
IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
IE: Unknown: DD1E00904C336E1013FFFF0000010000000000000000000000000C0000000000
IE: Unknown: DD1A00904C3401050100000000000000000000000000000000000000
IE: Unknown: DD07000C4304000000
Cell 03 - Address: 00:25:68:EB:3F:FC
Channel:11
Frequency:2.462 GHz (Channel 11)
Quality=26/70 Signal level=-84 dBm
Encryption key:on
ESSID:"vodafone3FFB"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s
Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s
Mode:Master
Extra:tsf=00000002f6c23184
Extra: Last beacon: 570ms ago
IE: Unknown: 000C766F6461666F6E6533464642
IE: Unknown: 010882848B960C121824
IE: Unknown: 03010B
IE: Unknown: 050400010000
IE: Unknown: 200100
IE: Unknown: 2A0104
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: Unknown: 32043048606C
IE: Unknown: DD180050F2020101020003A4000027A4000042435E0062322F00
IE: Unknown: DD1E00904C334E101BFFFF000000000000000000000000000000000000000000
IE: Unknown: 2D1A4E101BFFFF000000000000000000000000000000000000000000
IE: Unknown: DD1A00904C340B071B00000000000000000000000000000000000000
IE: Unknown: 3D160B071B00000000000000000000000000000000000000
IE: Unknown: DD0900037F01010000FF7F
IE: Unknown: DD0A00037F04010020000000
IE: Unknown: 0706494520010D14
[root@mzws ~]# wpa_supplicant -B -Dwext -i wlan0 -c /etc/wpa_supplicant.conf
[root@mzws ~]# iwconfig wlan0
wlan0 IEEE 802.11bgn ESSID:"Archer"
Mode:Managed Frequency:2.472 GHz Access Point: D8:5D:4C:59:52:EC
Bit Rate=1 Mb/s Tx-Power=14 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=66/70 Signal level=-44 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
[root@mzws ~]# sleep 10s;dhcpcd wlan0
dhcpcd[4076]: version 5.2.7 starting
dhcpcd[4076]: wlan0: rebinding lease of 192.168.1.102
dhcpcd[4076]: wlan0: carrier lost
dhcpcd[4076]: wlan0: carrier acquired
dhcpcd[4076]: wlan0: rebinding lease of 192.168.1.102
dhcpcd[4076]: wlan0: broadcasting for a lease
dhcpcd[4076]: wlan0: carrier lost
dhcpcd[4076]: wlan0: carrier acquired
dhcpcd[4076]: wlan0: rebinding lease of 192.168.1.102
dhcpcd[4076]: wlan0: broadcasting for a lease
dhcpcd[4076]: wlan0: carrier lost
dhcpcd[4076]: wlan0: carrier acquired
dhcpcd[4076]: wlan0: rebinding lease of 192.168.1.102
dhcpcd[4076]: timed out
I tried the "iwconfig wlan0 channel auto", but that didn't work. Here's the output of "lspci | grep -i net":
[root@mzws ~]# lspci | grep -i net
00:19.0 Ethernet controller: Intel Corporation 82567LF Gigabit Network Connection (rev 03)
03:00.0 Network controller: Intel Corporation WiFi Link 1000 Series
So what's the problem here? I searched the forum and google, and it seemed that I connected to a wrong router(for sometimes I only one "carrier lost" then "timed out"), but how was that happened? Things worked quite well before the upgrading as well as in my Windows environment.
Any reply would be appreciated! Thanks in advance!
Last edited by karbon (2010-08-23 06:40:10)

Thanks Proofrific, but I believe it's not, for the DHCP server is a built-in module in my wireless router.
I am now able to connect to my wireless network now. And it seems to be a little kernel bug as I discovered a thread(sorry but I forgot which one) in the forum discussing a similar problem.... Somebody in that post suggested a work-around to change the channel, as their default setting is channel 13 or 12.
I tried and it did work! Just simply open your router's setting page and then change the channel from auto to 3(in my case), and netcfg worked well now. For the manual configuration, I suppose the "iwconfig wlan0 channel 3" should be issued.
Thanks everyone in the forum for providing their solutions!

Power Mac Dual 1.8 Ghz: How do I connect to wireless network?

HELP!!!
I have this Power Mac Dual 1.8 Ghz with 10.4.11 OS. I used to use wire cable to connect the internet, but now the place I rent recently only provides wireless network. I was able to connect wireless network with my Windows Laptop.
Question: How do I connect my Dual 1.8 OS 10.4.11 with wireless network? I only see Internal Modern, Built-in Ethernet and Build-in FireWire options.

You can go the OWM route and get the airport extreme card and antenna
http://www.dvwarehouse.com/Apple-Airport-Extreme-Wireless-Card-802.11G-M8881-p-3 1367.html
http://www.dvwarehouse.com/Apple-Airport-External-Antenna-for-G5-2004-2005--MacP ro-Early-2008-A1066-922-6043---NEW-p-33986.html
Google the part numbers for more vender choices,
Or, you need to get a PCI WiFi card and antenna. BDAqua or Japamac have posted alternatives which are actually a little cheaper than the Apple parts.
The third alternative is a USB-based wireless adapter.

Need HELP! connecting to wireless network; IP Address problems!

I am trying to connect to wireless networks using the AirPort built into my MacBook Pro. There are two specific networks I am trying to connect to, both are WEP protected. I know the passwords and can get into each of them but I cannot connect to the internet, which is the main reason for connecting to them in the first place! When I go into System Preferences and click on Network, I see that next to AirPort it says I am connected to the network but may not be able to connect to the internet because my computer has a Self Assigned IP address. I assume this means my computer is not receiving an IP address from the network. I am set on full auto with DHCP. So what's wrong? Please Help!!!

That indicates that the MacBook Pro did not successfully communicate with the DHCP server on the network. Do those networks have access control (MAC address filtering) enabled? If so, the best solution is to reconfigure the base station so that this feature is disabled. This adds no real security since MAC addresses are easily discovered and cloned.
If you can't disable access control, you will need to add the MAC address of the wireless interface of your MacBook Pro to the list of allowed clients.

[SOLVED] Cannot connect to wireless networks any more after update

Hello,
I updated my system some days ago and, after that, I can't connect to wireless networks any more.
My network card is ath9k and I'm currently using wicd.
When I try to connect to my wireless network, I get "Veryfing AP association" message, then it fails to connect.
Here's the dmesg output :
[ 6369.650201] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6369.824358] r8169 0000:05:00.0 eth0: link down
[ 6369.824375] r8169 0000:05:00.0 eth0: link down
[ 6369.824398] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6369.936721] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6371.462702] r8169 0000:05:00.0 eth0: link up
[ 6371.462718] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6373.214209] wlan0: authenticate with 00:1c:10:57:47:17
[ 6373.236813] wlan0: send auth to 00:1c:10:57:47:17 (try 1/3)
[ 6373.248706] wlan0: authenticated
[ 6373.248735] ath9k 0000:09:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 6373.248737] ath9k 0000:09:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 6373.248739] ath9k 0000:09:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 6373.250756] wlan0: associate with 00:1c:10:57:47:17 (try 1/3)
[ 6373.253150] wlan0: RX AssocResp from 00:1c:10:57:47:17 (capab=0x411 status=0 aid=3)
[ 6373.253379] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 6373.253418] wlan0: associated
[ 6373.253431] ath9k 0000:09:00.0 wlan0: failed to set key 0
[ 6405.384916] wlan0: deauthenticating from 00:1c:10:57:47:17 by local choice (reason=3)
[ 6405.387398] cfg80211: Calling CRDA to update world regulatory domain
[ 6409.789779] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6409.890892] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6410.069734] r8169 0000:05:00.0 eth0: link down
[ 6410.069750] r8169 0000:05:00.0 eth0: link down
[ 6410.069778] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6410.263183] r8169 0000:05:00.0 eth0: link down
[ 6410.263212] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6411.717705] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6411.898268] r8169 0000:05:00.0 eth0: link down
[ 6411.898297] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6413.630832] r8169 0000:05:00.0 eth0: link up
[ 6413.630848] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6415.903790] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6416.089275] r8169 0000:05:00.0 eth0: link down
[ 6416.089302] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6416.089327] r8169 0000:05:00.0 eth0: link down
[ 6416.386308] r8169 0000:05:00.0 eth0: link down
[ 6416.386338] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6418.067675] r8169 0000:05:00.0 eth0: link up
[ 6418.067691] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
This particular line caught my attention: " wlan0: de-authenticating from 00:1c:10:57:47:17 by local choice (reason=3)". So I searched for it (without the MAC address) on the internet and found several solutions for it, involving wpa_supplicant, dhcpcd, IPv6 (disable it on /etc/sysctl.d/40-ipv6.conf) and card power management (operation not supported, don't have option on BIOS), but none of them worked for me.
Here's an excerpt from /var/log/wicd/wicd.log:
2014/03/01 11:48:15 :: Connecting to wireless network Curiosity
2014/03/01 11:48:15 :: Putting interface down
2014/03/01 11:48:15 :: Releasing DHCP leases...
2014/03/01 11:48:15 :: Setting false IP...
2014/03/01 11:48:15 :: Stopping wpa_supplicant
2014/03/01 11:48:15 :: Flushing the routing table...
2014/03/01 11:48:15 :: Putting interface up...
2014/03/01 11:48:17 :: Attempting to authenticate...
2014/03/01 11:48:19 :: Setting static IP : 192.168.2.188
2014/03/01 11:48:19 :: Setting default gateway : 192.168.2.1
2014/03/01 11:48:19 :: Verifying AP association...
2014/03/01 11:48:19 :: Attempt 1 of 10...
2014/03/01 11:48:24 :: Attempt 2 of 10...
2014/03/01 11:48:27 :: Attempt 3 of 10...
2014/03/01 11:48:30 :: Attempt 4 of 10...
2014/03/01 11:48:33 :: Attempt 5 of 10...
2014/03/01 11:48:36 :: Attempt 6 of 10...
2014/03/01 11:48:39 :: Attempt 7 of 10...
2014/03/01 11:48:42 :: Attempt 8 of 10...
2014/03/01 11:48:45 :: Attempt 9 of 10...
2014/03/01 11:48:48 :: Attempt 10 of 10...
2014/03/01 11:48:51 :: Connection Failed: Failed to ping the access point!
2014/03/01 11:48:51 :: exiting connection thread
2014/03/01 11:48:55 :: Sending connection attempt result association_failed
2014/03/01 11:48:55 :: Autoconnecting...
2014/03/01 11:48:55 :: Attempting to autoconnect with wired interface...
2014/03/01 11:48:55 :: Putting interface down
2014/03/01 11:48:55 :: Releasing DHCP leases...
2014/03/01 11:48:55 :: Setting false IP...
2014/03/01 11:48:55 :: Stopping wpa_supplicant
2014/03/01 11:48:55 :: Flushing the routing table...
2014/03/01 11:48:55 :: Putting interface up...
2014/03/01 11:48:58 :: Setting static IP : 192.168.2.188
2014/03/01 11:48:58 :: Setting default gateway : 192.168.2.1
2014/03/01 11:48:58 :: Connecting thread exiting.
2014/03/01 11:49:01 :: Putting interface down
2014/03/01 11:49:01 :: Releasing DHCP leases...
2014/03/01 11:49:01 :: Setting false IP...
2014/03/01 11:49:02 :: Stopping wpa_supplicant
2014/03/01 11:49:02 :: Flushing the routing table...
2014/03/01 11:49:02 :: Putting interface up...
2014/03/01 11:49:04 :: Setting static IP : 192.168.2.188
2014/03/01 11:49:04 :: Setting default gateway : 192.168.2.1
2014/03/01 11:49:04 :: Connecting thread exiting.
2014/03/01 11:49:07 :: Sending connection attempt result success
I've been connecting through wire since then and it's extremely uncomfortable being planted in one place.
Thanks.
Last edited by joaowojwicz (2014-04-03 12:17:53)

ewaller wrote:Well, let's start with a couple sanity checks. Look at the output of uname -a and of pacman -Qi linux and ensure that the running kernel (uname) is the same version that is installed.
Then. please post the output of lspci -nn and of ip link
Then, take a look at the output of sudo iw wlan0 scan
and see if you can see your AP. Also, verify that your wireless is called wlan0 by checking the ouput of ip link
Okay
>>log: uname -a
Linux Canopus 3.13.5-1-ARCH #1 SMP PREEMPT Sun Feb 23 00:10:07 CET 2014 i686 GNU/Linux
>>log: pacman -Qi linux
Name : linux
Version : 3.13.5-1
Description : The Linux kernel and modules
Architecture : i686
URL : http://www.kernel.org/
Licences : GPL2
Groups : base
Provides : kernel26=3.13.5
Depends On : coreutils linux-firmware kmod mkinitcpio>=0.7
Optional Deps : crda: to set the correct wireless channels of your country
Required By : None
Optional For : None
Conflicts With : kernel26
Replaces : kernel26
Installed Size : 61687.00 KiB
Packager : Thomas Bächler <[email protected]>
Build Date : Sat 22 Feb 2014 20:11:46 BRT
Install Date : Mon 24 Feb 2014 02:50:00 BRT
Install Reason : Explicitly installed
Install Script : Yes
Validated By : SHA256 Sum
>>log: lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09)
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09)
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05)
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05)
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5)
00:1c.1 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 [8086:1c12] (rev b5)
00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 [8086:1c16] (rev b5)
00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b5)
00:1c.7 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 [8086:1c1e] (rev b5)
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05)
00:1f.0 ISA bridge [0601]: Intel Corporation HM67 Express Chipset Family LPC Controller [8086:1c4b] (rev 05)
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 05)
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
09:00.0 Network controller [0280]: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
0b:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04)
Yes, my wireless is called wlan0. I linked something to /dev/null to get the predictable names
>>log: ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
link/ether 94:39:e5:f2:17:3f brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
link/ether 18:03:73:93:4d:1b brd ff:ff:ff:ff:ff:ff
I'll just paste my wireless connection here.
>>log: sudo iw wlan0 scan
BSS 00:1c:10:57:47:17(on wlan0)
TSF: 59645240249 usec (0d, 16:34:05)
freq: 2462
beacon interval: 100 TUs
capability: ESS Privacy ShortSlotTime (0x0411)
signal: -31.00 dBm
last seen: 260 ms ago
Information elements from Probe Response frame:
SSID: Curiosity
Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0
DS Parameter set: channel 11
ERP: Barker_Preamble_Mode
ERP D4.0: Barker_Preamble_Mode
Extended supported rates: 6.0 9.0 12.0 48.0
karol wrote:
Post the list of packages that were updated.
When posting configs, code or command output, please use [ code ] tags, not [ quote ] tags https://bbs.archlinux.org/help.php#bbcode
like this
It makes the code more readable and - in case of longer listings - more convenient to scroll through.
Okay, put code tag now. Here's the whole log since Feb, 24th. This was the day I started having problems.
[2014-02-24 02:32] [PACMAN] Running 'pacman -Suy'
[2014-02-24 02:32] [PACMAN] synchronizing package lists
[2014-02-24 02:32] [PACMAN] starting full system upgrade
[2014-02-24 02:49] [ALPM-SCRIPTLET] ==> Appending keys from archlinux.gpg...
[2014-02-24 02:49] [ALPM-SCRIPTLET] gpg: 3 marginal(s) needed, 1 complete(s) needed, PGP trust model
[2014-02-24 02:49] [ALPM-SCRIPTLET] gpg: depth: 0 valid: 1 signed: 6 trust: 0-, 0q, 0n, 0m, 0f, 1u
[2014-02-24 02:49] [ALPM-SCRIPTLET] gpg: depth: 1 valid: 6 signed: 60 trust: 1-, 0q, 0n, 5m, 0f, 0u
[2014-02-24 02:49] [ALPM-SCRIPTLET] gpg: depth: 2 valid: 60 signed: 4 trust: 60-, 0q, 0n, 0m, 0f, 0u
[2014-02-24 02:49] [ALPM-SCRIPTLET] gpg: next trustdb check due at 2015-03-31
[2014-02-24 02:49] [ALPM-SCRIPTLET] ==> Locally signing trusted keys in keyring...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Locally signing key 0E8B644079F599DFC1DDC3973348882F6AC6A4C2...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Locally signing key 684148BB25B49E986A4944C55184252D824B18E8...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Locally signing key 44D4A033AC140143927397D47EFD567D4C7EA887...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Locally signing key 27FFC4769E19F096D41D9265A04F9397CDFD6BB0...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Locally signing key AB19265E5D7D20687D303246BA1DFB64FFF979E7...
[2014-02-24 02:49] [ALPM-SCRIPTLET] ==> Importing owner trust values...
[2014-02-24 02:49] [ALPM-SCRIPTLET] ==> Disabling revoked keys in keyring...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key F5A361A3A13554B85E57DDDAAF7EF7873CFD4BB6...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 7FA647CD89891DEDC060287BB9113D1ED21E1A55...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key BC1FBE4D2826A0B51E47ED62E2539214C6C11350...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 4A8B17E20B88ACA61860009B5CED81B7C2E5C0D2...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 63F395DE2D6398BBE458F281F2DBB4931985A992...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 0B20CA1931F5DA3A70D0F8D2EA6836E1AB441196...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 8F76BEEA0289F9E1D3E229C05F946DED983D4366...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 66BD74A036D522F51DD70A3C7F2A16726521E06D...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 81D7F8241DB38BC759C80FCE3A726C6170E80477...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key E7210A59715F6940CF9A4E36A001876699AD6E84...
[2014-02-24 02:49] [ALPM-SCRIPTLET] ==> Updating trust database...
[2014-02-24 02:49] [ALPM-SCRIPTLET] gpg: next trustdb check due at 2015-03-31
[2014-02-24 02:49] [PACMAN] upgraded archlinux-keyring (20140124-1 -> 20140220-1)
[2014-02-24 02:49] [PACMAN] upgraded hicolor-icon-theme (0.12-2 -> 0.13-1)
[2014-02-24 02:49] [PACMAN] upgraded banshee (2.6.1-2 -> 2.6.2-1)
[2014-02-24 02:49] [PACMAN] upgraded bluez (5.14-1 -> 5.15-1)
[2014-02-24 02:49] [PACMAN] upgraded bluez-cups (5.14-1 -> 5.15-1)
[2014-02-24 02:49] [PACMAN] upgraded bluez-hid2hci (5.14-1 -> 5.15-1)
[2014-02-24 02:49] [PACMAN] upgraded bluez-libs (5.14-1 -> 5.15-1)
[2014-02-24 02:49] [PACMAN] upgraded bluez-plugins (5.14-1 -> 5.15-1)
[2014-02-24 02:49] [PACMAN] upgraded bluez-utils (5.14-1 -> 5.15-1)
[2014-02-24 02:49] [PACMAN] upgraded cairo-perl (1.103-2 -> 1.104-1)
[2014-02-24 02:49] [PACMAN] upgraded cups-filters (1.0.45-1 -> 1.0.46-1)
[2014-02-24 02:49] [PACMAN] upgraded dbus-glib (0.100.2-1 -> 0.102-1)
[2014-02-24 02:49] [PACMAN] upgraded dialog (1:1.2_20140112-1 -> 1:1.2_20140219-1)
[2014-02-24 02:49] [PACMAN] upgraded easytag (2.1.9-1 -> 2.1.10-1)
[2014-02-24 02:49] [PACMAN] upgraded ethtool (1:3.11-1 -> 1:3.13-1)
[2014-02-24 02:49] [PACMAN] upgraded flashplugin (11.2.202.336-1 -> 11.2.202.341-1)
[2014-02-24 02:49] [PACMAN] upgraded libpng (1.6.8-1 -> 1.6.9-1)
[2014-02-24 02:49] [PACMAN] upgraded gdk-pixbuf2 (2.30.4-1 -> 2.30.5-1)
[2014-02-24 02:49] [PACMAN] upgraded glib-perl (1.301-1 -> 1.304-1)
[2014-02-24 02:49] [PACMAN] upgraded gparted (0.17.0-2 -> 0.18.0-1)
[2014-02-24 02:49] [PACMAN] upgraded pango-perl (1.224-2 -> 1.225-1)
[2014-02-24 02:49] [PACMAN] upgraded gtk2-perl (1.247-2 -> 1.249-1)
[2014-02-24 02:49] [PACMAN] upgraded imagemagick (6.8.8.6-1 -> 6.8.8.7-1)
[2014-02-24 02:49] [PACMAN] upgraded kdesdk-poxml (4.12.2-1 -> 4.12.2-2)
[2014-02-24 02:49] [PACMAN] upgraded libass (0.10.2-2 -> 0.11.1-1)
[2014-02-24 02:49] [PACMAN] upgraded libfm (1.1.2.2-2 -> 1.2.0-3)
[2014-02-24 02:49] [PACMAN] upgraded libftdi (1.1-2 -> 1.1-3)
[2014-02-24 02:49] [PACMAN] upgraded libindi (0.9.6-7 -> 0.9.7-1)
[2014-02-24 02:49] [PACMAN] upgraded linux-firmware (20140123.418320b-1 -> 20140217.343e460-1)
[2014-02-24 02:50] [ALPM-SCRIPTLET] >>> Updating module dependencies. Please wait ...
[2014-02-24 02:50] [ALPM-SCRIPTLET] depmod: ERROR: Module 'hci_vhci' has devname (vhci) but lacks major and minor information. Ignoring.
[2014-02-24 02:50] [ALPM-SCRIPTLET] >>> Generating initial ramdisk, using mkinitcpio. Please wait...
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'default'
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux.img
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Starting build: 3.13.5-1-ARCH
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [base]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [udev]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [autodetect]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [modconf]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [block]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [filesystems]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [keyboard]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [fsck]
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Creating gzip initcpio image: /boot/initramfs-linux.img
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Image generation successful
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'fallback'
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Starting build: 3.13.5-1-ARCH
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [base]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [udev]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [modconf]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [block]
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: aic94xx
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: smsmdtv
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [filesystems]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [keyboard]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [fsck]
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Creating gzip initcpio image: /boot/initramfs-linux-fallback.img
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Image generation successful
[2014-02-24 02:50] [ALPM-SCRIPTLET] >>> WARNING: AT keyboard support is no longer built into the kernel.
[2014-02-24 02:50] [ALPM-SCRIPTLET] >>> In order to use your keyboard during early init, you MUST
[2014-02-24 02:50] [ALPM-SCRIPTLET] >>> include the 'keyboard' hook in your mkinitcpio.conf.
[2014-02-24 02:50] [PACMAN] upgraded linux (3.12.9-1 -> 3.13.5-1)
[2014-02-24 02:50] [PACMAN] upgraded linux-headers (3.12.9-1 -> 3.13.5-1)
[2014-02-24 02:50] [PACMAN] upgraded lirc-utils (1:0.9.0-69 -> 1:0.9.0-70)
[2014-02-24 02:50] [PACMAN] upgraded lynx (2.8.7-7 -> 2.8.8-1)
[2014-02-24 02:50] [PACMAN] upgraded man-pages (3.58-1 -> 3.60-1)
[2014-02-24 02:50] [PACMAN] upgraded mercurial (2.9-1 -> 2.9-2)
[2014-02-24 02:50] [PACMAN] upgraded mutter (3.10.3-1 -> 3.10.4-1)
[2014-02-24 02:50] [PACMAN] upgraded networkmanager (0.9.8.8-1 -> 0.9.8.8-3)
[2014-02-24 02:50] [PACMAN] upgraded networkmanager-pptp (0.9.8.4-1 -> 0.9.8.4-2)
[2014-02-24 02:50] [PACMAN] upgraded pcmanfm (1.1.2-2 -> 1.2.0-1)
[2014-02-24 02:50] [PACMAN] upgraded postgresql-libs (9.3.2-4 -> 9.3.3-1)
[2014-02-24 02:50] [PACMAN] upgraded ppp (2.4.5-8 -> 2.4.6-1)
[2014-02-24 02:50] [PACMAN] upgraded python2-configobj (4.7.2-6 -> 5.0.1-1)
[2014-02-24 02:50] [PACMAN] upgraded python2-urwid (1.1.1-1 -> 1.2.0-1)
[2014-02-24 02:50] [PACMAN] upgraded python2-zope-interface (4.0.5-2 -> 4.1.0-1)
[2014-02-24 02:50] [PACMAN] upgraded sbc (1.1-1 -> 1.2-1)
[2014-02-24 02:50] [PACMAN] upgraded t1lib (5.1.2-4 -> 5.1.2-5)
[2014-02-24 02:50] [PACMAN] upgraded totem-plparser (3.10.0-4 -> 3.10.1-1)
[2014-02-24 02:50] [PACMAN] upgraded vimpager (1.8.5-1 -> 1.8.6-1)
[2014-02-24 02:50] [PACMAN] upgraded vlc (2.1.3-1 -> 2.1.4-1)
[2014-02-24 02:50] [PACMAN] upgraded webkitgtk (2.2.4-2 -> 2.2.5-1)
[2014-02-24 02:50] [PACMAN] upgraded wine (1.7.12-2 -> 1.7.13-1)
[2014-02-24 02:50] [PACMAN] upgraded xarchiver (0.5.2-6 -> 0.5.3-1)
[2014-02-24 02:50] [PACMAN] upgraded xcb-util-wm (0.4.0-1 -> 0.4.1-1)
[2014-02-24 02:50] [PACMAN] upgraded xmlto (0.0.25-3 -> 0.0.25-5)
[2014-02-24 02:50] [PACMAN] upgraded youtube-dl (2014.02.13-1 -> 2014.02.22.1-1)
[2014-02-24 12:51] [PACMAN] Running 'pacman -Suy'
[2014-02-24 12:51] [PACMAN] synchronizing package lists
[2014-02-24 12:51] [PACMAN] starting full system upgrade
[2014-02-24 12:57] [PACMAN] upgraded ffmpeg (1:2.1.3-1 -> 1:2.1.4-1)
[2014-02-24 12:57] [PACMAN] upgraded libwbclient (4.1.4-1 -> 4.1.5-1)
[2014-02-24 12:57] [PACMAN] upgraded python2-configobj (5.0.1-1 -> 5.0.1-2)
[2014-02-24 12:57] [PACMAN] upgraded s-nail (14.5.2-4 -> 14.6-1)
[2014-02-24 12:57] [PACMAN] upgraded smbclient (4.1.4-1 -> 4.1.5-1)
[2014-02-24 12:57] [PACMAN] upgraded samba (4.1.4-1 -> 4.1.5-1)
[2014-02-24 12:57] [PACMAN] upgraded xbmc (12.3-8 -> 12.3-9)
[2014-02-24 13:19] [PACMAN] Running 'pacman -Syy'
[2014-02-24 13:19] [PACMAN] synchronizing package lists
[2014-02-24 13:20] [PACMAN] Running 'pacman -Suu dhcpcd'
[2014-02-24 13:20] [PACMAN] starting full system upgrade
[2014-02-24 13:24] [PACMAN] Running '/usr/bin/pacman -U /home/joaowojcikiewicz/z-aur/downgrade/downgrade-3.3-1-any.pkg.tar.xz'
[2014-02-24 13:24] [PACMAN] installed downgrade (3.3-1)
[2014-02-24 16:04] [PACMAN] Running 'pacman -Suy'
[2014-02-24 16:04] [PACMAN] synchronizing package lists
[2014-02-24 16:04] [PACMAN] starting full system upgrade
[2014-02-24 16:04] [PACMAN] upgraded vim-spell-br (20120506-1 -> 20120802-1)
[2014-02-24 16:04] [PACMAN] upgraded vim-spell-en (20120506-1 -> 20120802-1)
[2014-02-24 18:30] [PACMAN] Running 'pacman -Suy'
[2014-02-24 18:30] [PACMAN] synchronizing package lists
[2014-02-24 18:30] [PACMAN] starting full system upgrade
[2014-02-24 20:13] [PACMAN] Running 'pacman -Suy'
[2014-02-24 20:13] [PACMAN] synchronizing package lists
[2014-02-24 20:13] [PACMAN] starting full system upgrade
[2014-02-24 21:31] [PACMAN] Running 'pacman -Suy'
[2014-02-24 21:31] [PACMAN] synchronizing package lists
[2014-02-24 21:31] [PACMAN] starting full system upgrade
[2014-02-24 21:53] [PACMAN] Running 'pacman -Suy'
[2014-02-24 21:53] [PACMAN] synchronizing package lists
[2014-02-24 21:53] [PACMAN] starting full system upgrade
[2014-02-24 22:38] [PACMAN] Running 'pacman -R networkmanager'
[2014-02-24 22:39] [PACMAN] Running 'pacman -R networkmanager-openvpn networkmanager-pptp networkmanager network-manager-applet'
[2014-02-24 22:39] [PACMAN] Running 'pacman -R networkmanager-openvpn networkmanager-pptp networkmanager network-manager-applet kdeplasma-applets-networkmanagement telepathy-mission-control'
[2014-02-24 22:39] [PACMAN] Running 'pacman -R networkmanager-openvpn networkmanager-pptp networkmanager network-manager-applet kdeplasma-applets-networkmanagement telepathy-mission-control empathy telepathy-kde-common-internals'
[2014-02-24 22:40] [PACMAN] Running 'pacman -R networkmanager-openvpn networkmanager-pptp networkmanager network-manager-applet kdeplasma-applets-networkmanagement telepathy-mission-control empathy telepathy-kde-common-internals skype4empathy telepathy-kde-accounts-kcm telepathy-kde-approver telepathy-kde-auth-handler telepathy-kde-contact-list telepathy-kde-contact-runner telepathy-kde-desktop-applets telepathy-kde-filetransfer-handler telepathy-kde-integration-module'
[2014-02-24 22:40] [PACMAN] Running 'pacman -R networkmanager-openvpn networkmanager-pptp networkmanager network-manager-applet kdeplasma-applets-networkmanagement telepathy-mission-control empathy telepathy-kde-common-internals skype4empathy telepathy-kde-accounts-kcm telepathy-kde-approver telepathy-kde-auth-handler telepathy-kde-contact-list telepathy-kde-contact-runner telepathy-kde-desktop-applets telepathy-kde-filetransfer-handler telepathy-kde-integration-module telepathy-kde-send-file telepathy-kde-text-ui'
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-text-ui (0.7.1-2)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-send-file (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-integration-module (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-filetransfer-handler (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-desktop-applets (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-contact-runner (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-auth-handler (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-approver (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-accounts-kcm (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-contact-list (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed skype4empathy (20110407-4)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-common-internals (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed empathy (3.10.3-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-mission-control (5.16.0-1)
[2014-02-24 22:41] [PACMAN] removed kdeplasma-applets-networkmanagement (1:0.9.0.9-1)
[2014-02-24 22:41] [PACMAN] removed network-manager-applet (0.9.8.8-1)
[2014-02-24 22:41] [PACMAN] removed networkmanager-pptp (0.9.8.4-2)
[2014-02-24 22:41] [PACMAN] removed networkmanager-openvpn (0.9.8.4-1)
[2014-02-24 22:41] [ALPM] warning: /etc/NetworkManager/NetworkManager.conf saved as /etc/NetworkManager/NetworkManager.conf.pacsave
[2014-02-24 22:41] [PACMAN] removed networkmanager (0.9.8.8-3)
[2014-02-25 03:40] [PACMAN] Running 'pacman -Suy'
[2014-02-25 03:40] [PACMAN] synchronizing package lists
[2014-02-25 03:40] [PACMAN] starting full system upgrade
[2014-02-25 03:44] [PACMAN] upgraded youtube-dl (2014.02.22.1-1 -> 2014.02.24-1)
[2014-02-25 12:23] [PACMAN] Running 'pacman -Suy'
[2014-02-25 12:23] [PACMAN] synchronizing package lists
[2014-02-25 12:24] [PACMAN] starting full system upgrade
[2014-02-25 12:24] [PACMAN] upgraded dmenu (4.5-3 -> 4.5.13.5ed5e90-1)
[2014-02-25 12:24] [PACMAN] upgraded telepathy-glib (0.22.0-1 -> 0.22.1-1)
[2014-02-25 12:24] [PACMAN] upgraded tumbler (0.1.29-1 -> 0.1.30-1)
[2014-02-25 12:25] [PACMAN] upgraded youtube-dl (2014.02.24-1 -> 2014.02.25-1)
[2014-02-25 14:55] [PACMAN] Running 'pacman -Suy'
[2014-02-25 14:55] [PACMAN] synchronizing package lists
[2014-02-25 14:55] [PACMAN] starting full system upgrade
[2014-02-25 15:19] [PACMAN] upgraded ipython2 (1.1.0-1 -> 1.2.1-1)
[2014-02-25 15:19] [PACMAN] upgraded python2-pip (1.5.2-1 -> 1.5.4-1)
[2014-02-25 17:13] [PACMAN] Running 'pacman -Suy'
[2014-02-25 17:13] [PACMAN] synchronizing package lists
[2014-02-25 17:13] [PACMAN] starting full system upgrade
[2014-02-25 18:10] [PACMAN] Running 'pacman -Suy'
[2014-02-25 18:10] [PACMAN] synchronizing package lists
[2014-02-25 18:10] [PACMAN] starting full system upgrade
[2014-02-25 18:41] [PACMAN] Running 'pacman -S fbgrab'
[2014-02-25 18:41] [PACMAN] installed fbgrab (1.0-7)
[2014-02-26 13:19] [PACMAN] Running 'pacman -Suy'
[2014-02-26 13:19] [PACMAN] synchronizing package lists
[2014-02-26 13:19] [PACMAN] starting full system upgrade
[2014-02-26 13:25] [PACMAN] upgraded libmariadbclient (5.5.35-1 -> 5.5.36-1)
[2014-02-26 13:25] [PACMAN] upgraded mariadb-clients (5.5.35-1 -> 5.5.36-1)
[2014-02-26 13:25] [PACMAN] upgraded mariadb (5.5.35-1 -> 5.5.36-1)
[2014-02-26 13:25] [PACMAN] upgraded python2 (2.7.6-2 -> 2.7.6-3)
[2014-02-26 13:25] [PACMAN] upgraded s-nail (14.6-1 -> 14.6.1-1)
[2014-02-26 13:26] [PACMAN] upgraded xbmc (12.3-9 -> 12.3-10)
[2014-02-26 16:00] [PACMAN] Running '/usr/bin/pacman -S --asdeps qt>=4.6'
[2014-02-26 16:02] [PACMAN] Running '/usr/bin/pacman -S --asdeps qt>=4.6'
[2014-02-26 16:42] [PACMAN] Running 'pacman -Suy'
[2014-02-26 16:42] [PACMAN] synchronizing package lists
[2014-02-26 16:42] [PACMAN] starting full system upgrade
[2014-02-26 17:25] [PACMAN] Running 'pacman -Suy'
[2014-02-26 17:25] [PACMAN] synchronizing package lists
[2014-02-26 17:25] [PACMAN] starting full system upgrade
[2014-02-26 17:25] [PACMAN] upgraded libaccounts-glib (1.15-1 -> 1.16-1)
[2014-02-26 17:25] [PACMAN] upgraded libaccounts-qt (1.10-1 -> 1.11-1)
[2014-02-26 17:52] [PACMAN] Running 'pacman -Suy'
[2014-02-26 17:52] [PACMAN] synchronizing package lists
[2014-02-26 17:52] [PACMAN] starting full system upgrade
[2014-02-26 17:53] [PACMAN] upgraded signon (8.55-1 -> 8.56-1)
[2014-02-26 18:08] [PACMAN] Running 'pacman -Suy'
[2014-02-26 18:08] [PACMAN] synchronizing package lists
[2014-02-26 18:08] [PACMAN] starting full system upgrade
[2014-02-26 21:52] [PACMAN] Running 'pacman -Suy'
[2014-02-26 21:52] [PACMAN] synchronizing package lists
[2014-02-26 21:52] [PACMAN] starting full system upgrade
[2014-02-26 22:08] [PACMAN] upgraded grep (2.16-1 -> 2.18-1)
[2014-02-26 22:41] [PACMAN] Running 'pacman -S xchat'
[2014-02-26 22:41] [PACMAN] installed xchat (2.8.8-13)
[2014-02-27 00:02] [PACMAN] Running 'pacman -Suy'
[2014-02-27 00:02] [PACMAN] synchronizing package lists
[2014-02-27 00:02] [PACMAN] starting full system upgrade
[2014-02-27 01:41] [PACMAN] Running 'pacman -Suy'
[2014-02-27 01:41] [PACMAN] synchronizing package lists
[2014-02-27 01:41] [PACMAN] starting full system upgrade
[2014-02-27 12:20] [PACMAN] Running 'pacman -Suy'
[2014-02-27 12:20] [PACMAN] synchronizing package lists
[2014-02-27 12:20] [PACMAN] starting full system upgrade
[2014-02-27 12:26] [PACMAN] upgraded net-snmp (5.7.2-8 -> 5.7.2.1-1)
[2014-02-27 12:26] [PACMAN] upgraded youtube-dl (2014.02.25-1 -> 2014.02.26-1)
[2014-02-27 16:01] [PACMAN] Running 'pacman -Suy'
[2014-02-27 16:01] [PACMAN] synchronizing package lists
[2014-02-27 16:01] [PACMAN] starting full system upgrade
[2014-02-27 16:05] [PACMAN] upgraded wpa_supplicant (2.0-4 -> 2.1-3)
[2014-02-27 19:58] [PACMAN] Running 'pacman -Suy'
[2014-02-27 19:58] [PACMAN] synchronizing package lists
[2014-02-27 19:58] [PACMAN] starting full system upgrade
[2014-02-27 20:00] [PACMAN] Running 'pacman -S terminus'
[2014-02-27 20:00] [PACMAN] Running 'pacman -S terminus-font'
[2014-02-27 20:01] [PACMAN] installed terminus-font (4.38-4)
[2014-02-27 21:04] [PACMAN] Running 'pacman -Suy'
[2014-02-27 21:04] [PACMAN] synchronizing package lists
[2014-02-27 21:04] [PACMAN] starting full system upgrade
[2014-02-27 22:51] [PACMAN] Running 'pacman -Suy'
[2014-02-27 22:51] [PACMAN] synchronizing package lists
[2014-02-27 22:51] [PACMAN] starting full system upgrade
[2014-02-28 12:09] [PACMAN] Running 'pacman -Suy'
[2014-02-28 12:09] [PACMAN] synchronizing package lists
[2014-02-28 12:09] [PACMAN] starting full system upgrade
[2014-02-28 16:51] [PACMAN] Running 'pacman -Suy'
[2014-02-28 16:51] [PACMAN] synchronizing package lists
[2014-02-28 16:52] [PACMAN] starting full system upgrade
[2014-03-01 12:10] [PACMAN] Running 'pacman -S bluez'
[2014-03-01 12:19] [PACMAN] Running 'pacman -S xf86-input-joystick linuxconsole'
[2014-03-01 12:20] [PACMAN] installed xf86-input-joystick (1.6.2-3)
[2014-03-01 12:20] [PACMAN] installed linuxconsole (1.4.6-1)
[2014-03-01 12:21] [PACMAN] Running '/usr/bin/pacman -U /home/joaowojcikiewicz/z-aur/rejoystick/rejoystick-0.8.1-3-i686.pkg.tar.xz'
[2014-03-01 12:21] [PACMAN] installed rejoystick (0.8.1-3)
[2014-03-01 12:22] [PACMAN] Running '/usr/bin/pacman -U /home/joaowojcikiewicz/z-aur/joystick/joystick-20051019-12-i686.pkg.tar.xz'
[2014-03-01 12:48] [PACMAN] Running 'pacman -Suy'
[2014-03-01 12:48] [PACMAN] synchronizing package lists
[2014-03-01 12:48] [PACMAN] starting full system upgrade
[2014-03-01 12:49] [PACMAN] upgraded glibc (2.19-2 -> 2.19-3)
[2014-03-01 12:49] [PACMAN] upgraded device-mapper (2.02.105-1 -> 2.02.105-2)
[2014-03-01 12:49] [PACMAN] upgraded cryptsetup (1.6.3-2 -> 1.6.4-1)
[2014-03-01 12:49] [PACMAN] upgraded feh (2.9.3-1 -> 2.10-1)
[2014-03-01 12:49] [PACMAN] upgraded libtirpc (0.2.3-2 -> 0.2.4-1)
[2014-03-01 12:49] [PACMAN] upgraded readline (6.2.004-2 -> 6.3-1)
[2014-03-01 12:49] [PACMAN] upgraded lvm2 (2.02.105-1 -> 2.02.105-2)
[2014-03-01 12:49] [PACMAN] upgraded ppp (2.4.6-1 -> 2.4.6-2

Sangean digital radio with wireless network music player

Hi. I have just purchased a Sangean digital internet radio with wireless network player.
Can I link this to itunes on my 2010 Mac?
Is there any way I can easily convert my Itunes library to windows media player to support this functionality?

A couple of things that come to mind to check... Does the SBWM device connect to your wireless network when you turn it on? SBWM device on power up / init finishes with 2 solid green indicators. If it ends with 2 solid green then you can check the network assigned IP from the remote / system settings, make sure you're on the same subnet as your PC. If SBWM lights end up with solid blinking green the SBWM did not connect to the wireless network. If this is the case make sure your DSL modem has the radio turned on. Make sure the DSL modem has the 802.b protocol turned on. Do you use network security. The highest level security the SBWM will support is WEP 28, if your new DSL modem is set for WPA or higher the SBWM will not be able to connect to the network. If you were using WEP security on your old cable modem the key in the new DSL modem will need to be identical to what you had on your cable modem, or you'll have to do the SBWM network setup via USB to load the new WEP key to the SBWM device. Hope these suggestions are of use. W3

Can I connect to wireless networks far away?

How do I connect to wireless networks further away?
Is there a way I can improve my laptops wireless range so I can connect to wireless networks further away?

Hi!
You can only connect to wireless networks that the notebook recognizes. If the notebook recognizes a wireless network, you can connect to them. If it doesnt recognize (because it is further away) you can not connect.
Furthermore you can not improve the wireless range from the laptop. You can do this on a WLAN router, not on the notebook.
Bye

How to establish a trusted connection with JDBC for SQL SERVER 2000

Hi!I am using jdk 1.4 and eclipse 3.3.
I create a servlet in eclipse with in-build tomcat.
When I run it ,it was working perfectlly has it was suppose to work.
In this servlet I connect to a sql 2000 database using jdbc-odbc bridge driver.
But when I tried to deploy the servlet on tomcat 5.5 manully on the same machine ,it gave me error saying
[Microsoft][SQLServer JDBC Driver][SQLServer]Login failed
for user 'sa'
I searched around some post and found that ok ,I need trusted connection
But I have 2 Questions
1). Why was in eclipse I was able to connect to the SQL server and why not in the servlet which I deployed manully on tomcat.
2). How do I create a trusted connection with JDBC for SQL server 2000
Thnaks for your help in advance.

Hi! duffymo ,QussayNajjar ,dvohra09 .
Thank for help.
The ideas are really great.
I am trying generate reports for my company.
When I used eclipse the code worked perfectly.
below is code which I used
out.println("Calling For Class Name<br>");
Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
out.println("Calling For Class Name success Now calling database <br>");
1). jdbcConnection = DriverManager.getConnection("jdbc:odbc:SQLJasper");
2). jdbcConnection = DriverManager.getConnection("jdbc:odbc:Driver={SQL Server};Server=ServerName;Database=tempdb");
3). jdbcConnection = DriverManager.getConnection("jdbc:odbc:Driver={SQL Server};Server=ServerName;Database=tempdb","UID=UserName","Password=Password");
out.println("connecting to database success<br>");
I had tried to connect the database using this three way.
In 1st I tried using DSN name .
Next 2 self explainer for expert like you.
I used to 2nd variant to connect in eclipse and it worked fine.
I not an expert in java ,I just doing some research on jasperReport.
My best guest is that eclipse is using some library files of which I have no clue.
Thank's for your help,I appretiate it.
Once again thank a billion.
Sorry for the messy righting.

IPod nano does not connect with wireless earphone via bluetooth transmitters.

My iPod nano(6th) can not connect with wireless earphone via bluetooth transmitter.
I want to know which is wrong iPod nano or bluetooth transmitter...Now I tried with i10s because I thought previous one (motolora) might be wrong.
But both can not connect.

Sounds good. Hopefully they can provide you with an accurate answer.
B-rock

Impossible connecting with wireless network Netgear WNR 2000

Similar Messages

Maybe you are looking for