In which add-family,routing policy should apply for MPBGP ?
Hi,
IN MPBGP protocol, where i will apply routing policy to apply as- path prepand so that Route would be secondary to neighbor.
IGP-OSPF and BGP over MPLS is running.
on Which address-familiy nbr,should i apply, is it in VPNV4 or IPV4 or IPV4 VRF ?
if i want 10.36.128.0/26 prefix should go to Neigbhor MPLS R2, what should i use access-list or Prefix list?
please provide the reply with its config .
Topology like
regards,
Ajay
Hi Harlold,
Thanks for reply...
Please find the topology diagram
1. Yes ,both are MPLS Network.
2. L3VPN intraAS.
3.Mpls router 1 and 2 are PE to connect the SPs MPLS rtr.
4.My administration is upto Router R1.
5.Both MPLS Router R1 and R2 belongs to other Vendor which giving us mpls service . and they want from to advertise only VRF MGMT subnets only with AS Prepend .
So i want to where should Route-map apply? is it in address-family vpnv4 or ?
router bgp 64513
synchronization disable
neighbor 10.49.5.230 remote-as 64513
neighbor 10.49.5.230 update-source loopback1
address-family vpnv4
neighbor 10.49.5.230 activate
neighbor 10.49.5.230 send-community both
neighbor 10.49.5.230 route-map ONM_TO_AIR
Route-map ONM_TO_AIR
match ip add prefix-list ONM_TO_AIR
set as-path prepend 64513 64513 64513 64513.
ip prefix-list ONM_TO_AIR permit 10.49.30.128/26
will it work?
or I have to match extcommuntity in Route-map as it apply to vpnv4 add-family ?
Regards,
Ajay
Similar Messages
-
Trying to decide if I should apply for the Citi Double Cash
I have a ton of inquiries. Wanting to garden, but I want to try. Just approved for a Venture for $5k a few days ago. CLI with Citi AAdvantage yesterday. Denied for both Delta Exp and Amex. Denied for even a Macys CLI even though that's just a soft pull. I think the Delta wasn't even a pull because when I went to check on the status, it was "canceled" instead of denied - may have been because I applied for the Amex the day prior. Really wanting that Citi Double. I know, I'm an addict now.
Citi likes to pull EQ and EX, which are your lowest scores respectively. That, coupled with your INQ's, probably won't bode well for your recon. I wouldn't apply for DC again until you see that you're prequalified online for it (where you are given a specific APR range). Cold apping for it is risky, especially if you have a lot of INQ's. The DC is probably Citi's toughest card to get given its UW requirements. Sorry to hear about the decline.
-
Which Business Event fires when candidate applies for a vacancy?
Can somebody please confirm the workflow business event which fires when a candidate applies for a vacancy?
Is there an easy way of finding this out or some doco which mentioned what events are called when?
Thanks.Hi Shruti,
Theoretically speaking you can edit the workflow process and achieve your objective (Using Workflow Builder) by designing what triggers to be fired once the AutoCreate Configuration Item completes.
See if the following docs give you any hints:
Oracle Order Management Using Oracle Workflow in Oracle Order Management
AutoCreating Configuration Items and Final Assembly Orders (Oracle Bills of Material Help)
AutoCreate Configuration Items (Oracle Bills of Material Help)
Thanks &
Best Regards, -
I want a i pad?but which is the one i should go for, model.
I would like an i pad 2,i think but with 6 to choose from and a light usser which do i go for model wise.Any sugestions gratly apreaseated.
What are all the differences between the iPad 3rd Gen and the iPad 2? Is the iPad 2 worth the cost savings?
http://everymac.com/systems/apple/ipad/ipad-faq/differences-between-ipad-3rd-gen -2012-ipad-2-2011.html
What are all the differences between the iPad 3rd Gen models? Which should I buy?
http://everymac.com/systems/apple/ipad/ipad-faq/differences-between-ipad-3rd-gen -early-2012-models.html
Should I Buy a New iPad? Or an iPad 2?
http://www.maclife.com/article/blogs/should_i_buy_new_ipad_or_ipad_2
iPad Q&A
http://www.everymac.com/systems/apple/ipad/ipad-faq/differences-between-ipad-3rd -gen-early-2012-models.html
A Few Questions (and Answers) About the New iPad
http://pogue.blogs.nytimes.com/2012/03/15/a-few-questions-and-answers-about-the- new-ipad/?ref=personaltechemail&nl=technology&emc=edit_ct_20120315
New iPad: A Polishing of the Old
http://www.nytimes.com/2012/03/15/technology/personaltech/the-new-ipad-is-much-t he-same-only-better.html?nl=technology&emc=edit_ct_20120315
iPad 1, 2 and New Specifications
http://www.everymac.com/systems/apple/ipad/index-ipad-specs.html
How much content will fit on my iPod or iPhone?
http://support.apple.com/kb/HT1867
If you think you may get an iPad 2:
Refurbished iPad Prices
http://store.apple.com/us/browse/home/specialdeals/ipad
New 16GB iPad 2 Prices
http://store.apple.com/us/browse/home/shop_ipad/family/ipad/select_ipad2
Cheers, Tom -
Which version of SQL server should install for persistent chat?
hi
after i got error that i put picture below
i decided to install sql server again for service persistent chat
but i don't know which version should i download? and again i don't know how i should delete last sql server?
which one i should download?
1-2008 Express
2-2008 R2 enterprise
3-2008 R2 SP2 - Express EditionAs per the above error you are trying to install 2008 sql server which is not supported.
you have to install SQL Server 2008R2 or 2012. Check this link
http://technet.microsoft.com/en-us/library/gg398495.aspx
Whenever you see a helpful reply, click on Vote As Helpful & click on Mark As Answer if a post answers your question. -
I inserted a MP4 video on a page - GMX Tree Service - Tree Trimming, Stump Grinding, Tree Removal Services and Firewood Sales in Toms River NJ - and it plays correctly and is in the correct direction on my PC, but when you view it on your IPad or phone it shows up sideways. Is there additional code necessary to make it play in the correct direction?
Right. You're using XHTML doc type with HTML5 <video> tags. So the W3C code validation is showing invalid code errors. If you're going to use HTML5, you must be consistent throughout.
I don't know which version of DW you have, but in CS5 forward you have the option to use HTML5 doc types. Go to Modify > Page Properties > Title/Encoding. Click on screenshot.
If your version is older than that, you'll need to do it manually in Code View.
See HTML5 syntax
HTML5 Introduction
Nancy O. -
No guidance as to which version of desktop one should load for a particular handheld
I know that different versions of the desktop software are geared for the latest and greatest new models. I have a 7130 dinasour. I want to know what is the most recent software that is good to safely load that will work well with my device, not the Bold or Storm. This should be easily findable on the website. grrrrrr
Anyone have advice for me???
Also, I use ACT to sync contacts, and I always get the message about ASCII import/export not available. What is thebest way to import notes and other text files into the blackberry for us non-outlook users??
Much thanks for any help
Leonard
Solved!
Go to Solution.Correct, 4.3 and above won't work.
Not sure about the ASCII Importer. Are you using 4.2 now and it's not working?
The following choices should be available in DM 4.2: http://www.blackberry.com/btsc/KB04312
If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
Remember to resolve your thread by clicking Accepted Solution. -
Which IOS 7 Beta 2 model applies for an Ipad 4 without LTE networks ?
Hi. The Ipad 4 have 3 models for download the IOS 7 beta 2... but which one without LTE networks ???
Today I went to the Apple store and they replaced the iPad:
Issue: Customer stated that it restarted often after updated iOS 7.0.2
Steps to Reproduce: Verified that there is numerous panic on iPad diagnostics.
Proposed Resolution: Swap
The clues of trouble included difficulty in loading, restarts even when not in use and draining battery. And there were maybe 100+ panics. The original iOS-7.0.0 load appeared to work correctly, why it didn't with 7.0.2 is not known to me, but it pays to have the extended warranty and an Apple store not too far away! -
Which add-on should I use for displaying Page Rank?
Please tell me the add-ons that I can use for letting me know the Page Rank of a website.
Google PR and Alexa PR is needed.
Thank YouHave you tried [https://addons.mozilla.org/bn-BD/firefox/addon/seo-status-pagerankalexa-toolb/ SEO Status PageRank/Alexa Toolbar] ? I don't know of Google PR...sorry!
-
Which card should i apply for?
Hi,I have about 6500 in credit card debt with no baddies. About 55% utilization. I am thinking about applying for a card to transfer my balance over @ 0%. Scores are 660,663,666. What do you guys recommend?
drvbasic wrote:
Hi,I have about 6500 in credit card debt with no baddies. About 55% utilization. I am thinking about applying for a card to transfer my balance over @ 0%. Scores are 660,663,666. What do you guys recommend?Have you requested a CLI with the current card? Who is it with? What is the current APR? Have you contacted them to see if they would lower your APR (cap1 does this frequently) in the mean time?(Balance transfers take 7 days to a month!) Request CLI on all other cards. What other cards do you have? Your scores are good enough for Amex ...possibly. See if they prequal you for 0 for 15months. Doubt they would give you a limit higher than 5k. you could split it between two new cards? I would say 6500 is not quite enough for a consolidation loan. What do you fellow myficoers think? Worst case scenario, your credit takes a hit for opening a new account, the new limit will lower your total UTIL, so may see it go up, but when you do the BT it will swing back a bit, but overall you could be higher than lower with scores. Transfer it all to the new card, pay it down fast, and you may be surprised at the results. Your inquiries are high now, so you could just be forced to app for cap1. Only the qs, qs1, venture1, and prestige will offer 0% interest. Leave capital one as a last resort because they wont care about adding 1 or 2 more inquiries...Venture1 will have the higher limit most likely so do that first. -
Hi all: This has me scratching my head. We run ZCM 11.2.2 mu2 on all servers and workstations. The primary server is on an OES2 SP3 box while all clients run Windows XP sp3, ZCM 11.2.2 mu2 and the Novell client.
I have a particular group of users which has two policies assigned to them. The first is a user-associated Windows XP user Group Policy, and the second is a Windows XP Workstation computer policy. ZENworks adaptive agent shows them as successful.
The policy in question is a Windows XP User Group Policy. When I run rsop.msc, the resulting GP set clearly shows none of the user group policy settings present, but as stated above, the adaptive agent does show them as successful. The only thing I can think of is that the user group policy is being over-written by another policy. In the past there was a setting make sure the user policy was applied last.
Any suggestions on how to fix this? Thanks, Chris.Originally Posted by Chris
Hi all: This has me scratching my head. We run ZCM 11.2.2 mu2 on all servers and workstations. The primary server is on an OES2 SP3 box while all clients run Windows XP sp3, ZCM 11.2.2 mu2 and the Novell client.
I have a particular group of users which has two policies assigned to them. The first is a user-associated Windows XP user Group Policy, and the second is a Windows XP Workstation computer policy. ZENworks adaptive agent shows them as successful.
The policy in question is a Windows XP User Group Policy. When I run rsop.msc, the resulting GP set clearly shows none of the user group policy settings present, but as stated above, the adaptive agent does show them as successful. The only thing I can think of is that the user group policy is being over-written by another policy. In the past there was a setting make sure the user policy was applied last.
Any suggestions on how to fix this? Thanks, Chris.
The setting is still there, when you assign the policy in step 2 it will ask the following:
Specify how policy conflicts should be resolved.
User Last - device associated policies applied first followed by user associated policies
Device Last - user associated policies applied first followed by device associated policies
Device Only - user associated policies ignored
User Only - device associated policies ignored
Thomas -
Does a route-policy override BGP split-horizon rule in IOS-XR?
If I receive a default route from a non-client, can I turn around and send it to another non client if I have the following applied to the non-client?
prefix-set send-default
0.0.0.0/0
end-set
route-policy DEFAULT-POLICY
if destination in send-default then
pass
else
drop
endif
end-policy
neighbor-group BLAH
remote-as XXXXX
password encrypted XXXXXXX
description iBGP to Decryptors
update-source Loopback0
address-family ipv4 unicast
route-policy DEFAULT-POLICY out
soft-reconfiguration inbound always
neighbor X.X.X.X
use neighbor-group BLAH
endHi Carlopez,
For BGP to inject a default rotue you need the "default-information originate" command, unfortunately, you can't redistribute or regenerate a route via the RPL method you described.
regards
xander -
Rt-filter or route-policy in a route-reflector
Hi,
I want to implement a route reflector that i will use in two differents networks with differents VPNL3. So i do not want that my route reflector advertise the prefixes form a network to the other. I am using an ASR9000 with IOS XR 4.3.2 as route reflector.
I tried two differents configurations in a testing enviroment and both work fine, one applying route-policy filtering by RD, and another using RT-filter. But i do not know what is better to implement on production. I will appreciate if somebody could help me to decide what is the best to implement in a production Network, thinking in the resources of the network and in the IPv6 deployment (i could not configure RT Filter with address-family ipv6)
With route-policy
rd-set RD_XXX
65000:*
end-set
route-policy to_XXX
if rd in RD_XXX then
pass
else
drop
endif
end-policy
route-policy to_YYY
if rd in RD_XXX then
drop
else
pass
endif
end-policy
router bgp 65001
neighbor-group XXX
remote-as 65001
address-family vpnv4 unicast
route-reflector-client
route-policy to_XXX out
neighbor-group YYY
remote-as 650001
update-source Loopback0
address-family vpnv4 unicast
route-reflector-client
route-policy to_YYY out
with RT-Filter
router bgp 65001
address-family ipv4 rt-filter
neighbor-group XXX
address-family ipv4 rt-filter
route-reflector-client
soft-reconfiguration inbound always
neighbor-group YYY
address-family ipv4 rt-filter
route-reflector-client
soft-reconfiguration inbound always
RegardsHi,
One benefit I see with rt-filter is, this feature provides considerable savings in CPU cycles and transient memory usage, generally this will be beneficial when you have large number of prefixes to be filtered, as you do not need to define route-policy for all the prefixes, and also it simple to configure (only one command )
Look at the Restrictions for BGP: RT Constrained Route Distribution in below document
http://www.cisco.com/en/US/docs/ios/ios_xe/iproute_bgp/configuration/guide/irg_rt_filter_xe.html
HTH
Regards,
Sandip -
For Switzerland country unable to add family dependedts
In ESS u2013 Family Members/dependents, we are not able to add a child / Spouse. It shows an error. Insured number is vacant but there is no field for insurance number in the portal.
Any helpfull suggestions please
Regards,
Murali
Edited by: Murali Manohar on Jan 18, 2009 11:55 AMYes I believe so as well. The reason why they do this... If you have the money to add a line you should have money to have all lines active which is the original intent for suspend a line without billing.
-
Problem with route-policy and taging
Hey!
I'm trying to apply the following configuration but are receving the follow error:
!!% Policy [aggregate-routes] uses the 'tag' attribute. There is no 'tag' attribute at the bgp aggregation-dflt attach point.
route-policy aggregate-routes
set community test
set community test1
if tag eq 1000 then
set community (65000:1,65000:2,65000:3)
endif
end-policy
router static
address-family ipv4 unicast
10.1.1.0/24 Null0 tag 1000
router bgp 65000
address-family ipv4 unicast
aggregate-address 10.1.1.0/24 route-policy aggregate-routesHello.
Please find set/match attributes per attach point in the following document - http://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k_r4-2/routing/configuration/guide/b_routing_cg42asr9k/b_routing_cg42asr9k_chapter_0110.html#con_1240966
Match tag is not supported for the attach point.
Maybe you are looking for
-
HT204053 Set up Find my Mac with two iCloud accounts, same iTunes account?
My wife and I use the same iTunes store account, but separate iCloud accounts. When I try to add "Find my Mac" on her Macbook Air, it indicates that only my user ID can use that service. How can I put her computer on her iCloud account, so that we
-
Communication in distributed systems book
hi all i am lookig for good book which describe communication in distributed systems
-
Ellipse recoginition in images
Hi, I'm trying to implement an algorithm (not Hough transform) for ellipse recogintion in images, and I find few few information about this in the net (I suppose I'm not knowing how to find it) and even less code or documentation as an example and gu
-
Issue with PXI 6528 test panels
We are using a real time 8106 controller in a PXI rack with some 6528 digital I/O boards. We have loaded all necessary drivers to the system and can see the cards in Max but are unable to run Test panels as the options to set the port bit states are
-
Release stratergy not effecting
Hi, after making any changes in PO release statergy is not effecting ? Regards rahul