Infinity 2, IP Profiles and how to find it....

New to the forum and new to Infinity so go easy on me...
Was using Total Broadband until a few days ago.  Using the BT speed tester [ADSL and FTTC option] used to give upload, download speeds plus IP Profile information.  Plently of posts show screen shots of Infinity tests with this same checker, but it errors out for me each time I try to use it now I'm on Infinity.
Trying to work out what the profile is with the new connection but the beta speed tests linked from the Help pages don't give that information. 
The new Openreach modem is [unless I hack it] a brick to me...?  There's no way I can get any information out of it I assume...?
Waiting for my 10 days to elapse before I can be sure that the circuit has settled correctly, but right now I'm getting 47Mb down and 16 up which is significantly less than the estimated 66.5 down and 20 up. 
I was previously happy with the speed from Total Broadband, partly because I was getting over the estimated figures [after a line fault was fixed] and partly because it was a good overall figure based on my distance from the exchange.  Measured speeds were 15mb down and 1.1mb up, estimated were 12mb down and 1mb up.  Thus what I'm getting now is a bit disappointing really.  Don't get me wrong, it's still significantly more than I had but below the expectation BT set. 
The trend from the BT beta speedtest site, and also speedtest.net, shows a gradual drop from the initial speed test results of 54mb to what I now see....

Actually that is wired.
That was why I was so keen to find out the IP Profile, but for reason's I don't understand the BT Speed checkers seem to keep erroring out on me.  They do the actual up/download tests and then error out before displaying the results.
I found the link to the BT Wholesale speed checker in the forums in one of the posts I read doing some research and amazingly that worked, but only the once.
Now I know that the line appears good I can start checking other things.  Swapping cables, using my son's laptop instead of my desktop etc to try to isolate the issue.  It's always possible that the problem causing the slow download is causing the tests to fail too.....
My desktop is at the end of a long ethernet cable - well within the 100m allowed in the standard - but if that's damaged that could be it.  I can take a shorter cable and his latop and try right next to the homehub to see what changes.  Unhooking and replacing the cable to my desktop will be a nightmare of a job and I didn't want to start down that route if the IP Profile was 53mb and my download was 50mb..!
Looks like I have a fun weekend ahead of me...!

Similar Messages

  • When I open iPhoto 9.2.1 it says that my library needs to be upgraded but when I upgrade the library I am trying to open (33 GB worth of pictures from 2006) the new application says it cannot read the files and how to find them on the system to reimport?!

    When I open iPhoto 9.2.1 it says that my library needs to be upgraded but when I upgrade the library I am trying to open (33 GB worth of pictures from 2006) the new application says it cannot read the files and how to find them on the system to reimport?! and then I'd like to erase the original files since the space requirement is huge!!!! Why is upgrading software iPhoto such a pain. I've gotta get a presentation done and all I get for my money is roadblock!!!

    hello, it sounds like the library is damaged.
    Download iPhoto Library Manager and use its rebuild function. This will create a new library based on data in the albumdata.xml file. Not everything will be brought over - no slideshows, books or calendars, for instance - but it should get all your albums and keywords back.
    Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one. 

  • Where and how to find the storage locatation for the consignment stock

    where and how to find the storage locatation for the consignment stock (customer stock )  for more than one storage location .
    table :msku
    material no    -   werks - batch
    xxx                   sg11  - 200352ac
    table : mchb
    material no    -   werks  -lgort - batch
    xxx                   sg11   sg10   200352ac
    xxx                   sg11   gs11   200352ac
    note : each stock location having same batch no in different storage and my question how to find which link for msku to mchb .

    Hi,
    Try the table MARD: Storage Location Data for Material, where in the field LABST will give the stock field, against a given material/plant/Storage Loc.
    Regards,
    JLN

  • What do you mean by Time profile and how to configure it.

    Hi Gurus,
    can anybody tel me what do you mean by Time profile and how to configure it.
    we are using Capacity requiremtn planning.
    best regards
    prashanth

    Hi Prashanth,
    Time profile can be customized using transaction OPD2.
    It contains the time horizons for importing the data records as well as for evaluation and planning.
    the planning horizon must be smaller or equal to the database read period.
    SAPPM_Z002 is a sample time profile
    The list profile defines teh presentaion of the output lists,transaction used is OPDH.
    best regards
    vijay

  • HT3546 So i recently bought an Apple AirPort Extreme BaseStation (the mushroom shaped one) and was wondering if someone could tell me where and how to find a power cord and how to set it up with my Macintosh (2011 edition with 1.7.5) Thankyou! :)

    So i recently bought an Apple AirPort Extreme BaseStation (the mushroom shaped one) and was wondering if someone could tell me where and how to find a power cord and how to set it up with my Macintosh (2011 edition with 1.7.5) Thankyou!

    Welcome!
    Last question first, as we need to know what operating system that the Mac is using.
    If you are not sure, click the Apple icon in the upper left corner of the screen, then click About This Mac, and post back with the OS X Version number that you see there.
    Two possible solutions on the power cord
    ORIGINAL OEM APPLE AIRPORT EXTREME BASE STATION POWER SUPPLY AC ADAPTER A1202 if you want a white power supply and white power cord to match up with the Apple device
    AC adapter for Apple AirPort A1034 Extreme B... if you don't care what color the supply and cord might be
    If you don't already have a Setup Guide.....look here:
    AirPort Extreme Base Station Setup Guide v4.2 (Manual)

  • What is a root folder and how to find folders afte...

    Can someone tell me what a 'root folder' is and how to find icons once you've moved it there?
    It's actually my boyfriend's phone and he uses it for construction site pictures and this morning he woke me up as he couldn't find it anymore. He needs to locate the folder asap as he needs to download pics onto the computer and send them to clients straightaway in batches.
    I connected the phone to the computer using the usb cord and it asks for options on the mass storage transfer. I selected 'images' and then on the control panel of windows, select digital still camera. At this point, the computer stalls as it is trying to search for the pictures folder but cannot locate.
    I'll never move anything to this 'root folder' again. I was just trying to put the icon on the main menu (the way you can do with a blackberry)
    He's already gone for work so took the phone with him, so I thought of giving this forum a try.
    Thanks for help in advance

    Hi there! 
    Well If what you did is you transfered the Pictures from one folder to another using your phone, the Root folder is the main folder so lets say you transfered it to the memory card the root folder is the memory card.
    Hope tis' help!
    "If you think this post is helpful, please click on the green button"

  • Hello. I'd like to get learning and become certified. What should I do and how to find the link for staring education?

    Hello. I'd like to get learning and become certified. What should I do and how to find the link for staring education?

    Hello there, g0ddess.
    The following link proves to be a great resource to get started with Apple  Training and Certification:
    Training and Certification
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • Why the App Store ask for sq.after using it for years and how do find the answers

    Why the App Store ask for sq.after using it for years and how do find the answers

    Reset security questions
    http://support.apple.com/kb/HT5312
    If you do not have a Rescue email, you need to contact apple support, they will guide you through the process of resetting your security questions.
    https://ssl.apple.com/emea/support/itunes/contact.html

  • Is it possible and how to find out what host, if any, is connected to a remote PXI prior to switching execution target programmatically or in devlopment environment?

    Is it possible and how to find out what host, if any, is connected to a remote PXI prior to switching execution target programmatically or in devlopment environment?

    This functionality is not available in LabVIEW RT. If you attempt to switch execution target to an RT controller already targetted by someone else, it will tell you too many hosts are connected and fail. Of course if it allows you to switch, then no one was connected. By attempting to switch execution target you can use the message above to determine if anyone is targetted or not, but if someone is, there is no way to determine who.
    If you are concerned about this sort of thing, you might check the RT target options in LabVIEW RT to change the IP access list for hosts that are allowed to switch execution target to it.

  • I created an administrator pseudo profile and made my profile standard. but when i restarted there another profile in my log-in page. when i log in to that unknown profile i cannot log-in. what is that profile and how can i delete it? thanks

    i have a rmbp 15" osx.. my case is this: i created an administrator pseudo profile and made my profile standard. wel i read from another forum, to strengthen my malware security.. but when i restarted there's another profile in my log-in page stating "needs updating". when i log in to that unknown profile i cannot log-in. what is that profile and how can i delete it? thanks

    Resetting User Account Password (10.7 +)
    1) Boot into your Recovery Partition holding down command + R at the startup chime
    2) Select 'Terminal' from your Utilities Menu Bar
    3) Type the following bolded command in: resetpassword
    4) From the window that appears, select your boot volume and the appropriate user account
    5) Type in the new password and confirm the new password
    6) Click Save, close this pane and quit Utilities
    7) Select your boot volume when presented with choose startup disk and reboot your machine

  • Where can I find the forum premiere elements? and how to find my own questions asked return?

    waar vind ik het premiere elements forum en hoe vind ik mijn eigen gestelde vragen terug?
    where can I find the forum premiere elements? and how to find my own questions asked return?

    arkitsa wrote:
    thank you 99jon, but still difficult to find your own questions back.
    Click on this:
    then this:
    and finally this:
    And your posts will be listed.

  • HT5557 I have mistakenly started a audio that read my text and books.  What is that and how do find it?

    I have mistakenly started a audio that read my text and books.  What is that and how do find it?

    If there is a box around what it's reading that's Voiceover and you can ask Siri to turn it off.
    if you run two fingers down the page and it reads thats speak screen. Go to settings> general> accessibility> speech> speak screen> off.

  • What is CPI-C  and how to find the username and password for a 4.7c install

    Dear Friends,
    Please tell me what is a CPI-C username is ??
    When do we use it?
    And how/from where  could  I find the CPI-C user name and password of a particular system(4.7c)?
    Please give me a detail knowledge.
    waiting for replies ....
    thx,
    jeevan

    OS X 10.7 Lion, 10.8 Mountain Lion & 10.9 Mavericks
    Reset Password starting from Recovery HD
    Start the computer,then press and hold down command and R keys to start into recovery partition.
    When you see the Apple logo, release the keys.
    Wait until  OS X Utilities window shows up.
    Move the mouse to the menubar at the top and click "Utilities", then select "Terminal"
    from the drop down.
    Terminal window will appear.
    Type in   resetpassword   and press enter on the keyboard.
    Leave the Terminal window open.
    Reset Password Utility window will open with Macintosh HD selected.
    Select the user account from the popup menu box.
    Enter a new password.
    Reenter the new password for the user.
    Enter a hint.
    Click the "Save" button.
    Click  in the menubar and select Restart.
    Log in.
    If Keychain dialog box appears, select “Create New Keychain”.

  • How to find a badi and how to find the method/methods for a transaction?

    Hi all,
    i need to give a text either while creating customer (vd01) or changing customer(vd02)...thsi is via extras->texts.....then I have to double clik the text and go to change editor...and then i have to clik on insert line and then choose text element radiobutton on screen and then give it a name and then save it..this should be done for all customers....my problem is i am unable to find a badi and the appropriate method for thsi..i have placed break point in method read_add_on_data in the badi customer_add_data....i tested both by transactions va01 and va02 but of no use..also there are so many methods..can u tell me how do i find the appropriate method of the appropriate badi.....

    Hi,
       For XD01/XD02/XD03 The following BADI's are useful
    business Add-In CUSTOMER_ADD_DATA  and  business Add-In CUSTOMER_ADD_DATA_CS .
    *<b>Reward points</b>
    Regards

  • 2d Direct draw, and how to find out if the application is a java apps

    I am running a banner application that was written in java. And in some instances, we are seeing the banner flicker every 5 seconds or 10 seconds. The banner application is written by some other government branch and on their documentation they say that the flickering is due to java's 2D directdraw used by some other java application (not their banner application). I personally haven't seen this on our test VMs but it is being seen on some physical workstation at the client site.
    I am trying to find out the application that is using java's 2D directdraw in our environment. Some of the question I have is
    1) Is there anyway to find out what application is using java 2D directdraw? ( I know how to disabled it globally for java but don't want to do that, I would rather just disable it for one application than disabling it on all java application)
    2) Is there anyway to find out what applications are depended in JVM on a machine? So that I can narrow the list of application to test.
    3) Is there anyway to find out if a application is written in java. Our environments have a lot of applications installed on them and I'm not sure which one use JVM and which one don't. If there is a way to know that then I can narrow down my issue and try to solve it.
    Thank you for your help, I really appreciate it,
    Sudeep.

    Hi,
    if the database is running, start a sqlplus session. You will see in the banner something like '64Bit Production' (for 64-bit) or only 'Production' for 32-bit. Alternatively, especially if the database is not running, go to $ORACLE_HOME/bin and type 'file oracle'. The returning strings shows either 32-bit or 64-bit.
    Best regards
    Werner

Maybe you are looking for