Integration of SMS with Cisco LMS 3.2

Hi,
Need assistance to confirm if SMS alerts can be integration with LMS 3.2. If yes, could you please walk me though the process.
Rgds.....Navinder

No,
Trap email and syslog are possible from DFM for DFM alerts
Mail and script are possible from RME syslog handler
It is easy to create a sms mailgateway though.
Opensoure software that can sms via a gsm connected to pc is also easy to find. E;g; gnokii
Cheers,
Michel

Similar Messages

Icmp Jitter collector configuration with Cisco LMS

Hi,
I am trying to collect jitter information of cisco Routers which are added in Cisco LMS
I have configured collector icmp jitter for them but somehow no stats are visible in lms and its says in IPM that u have no jitter collectors configured.
Do i need to enable anything on the Router as well to export stats to LMS ?
Thanks

Hi,
show ip sla application
IP Service Level Agreements
Version: Round Trip Time MIB 2.2.0, Infrastructure Engine-II
Time of last change in whole IP SLAs: *07:35:21.730 UTC Thu Mar 13 2014
Estimated system max number of entries: 27977
Estimated number of configurable operations: 27976
Number of Entries configured : 1
Number of active Entries : 1
Number of pending Entries : 0
Number of inactive Entries : 0
Supported Operation Types
Type of Operation to Perform: dhcp
Type of Operation to Perform: dns
Type of Operation to Perform: echo
Type of Operation to Perform: frameRelay
Type of Operation to Perform: ftp
Type of Operation to Perform: http
Type of Operation to Perform: icmpJitter
Type of Operation to Perform: jitter
Type of Operation to Perform: pathEcho
Type of Operation to Perform: pathJitter
Type of Operation to Perform: slm controller
Type of Operation to Perform: slm frame-relay interface
Type of Operation to Perform: slm frame-relay pvc
Type of Operation to Perform: slm interface
Type of Operation to Perform: tcpConnect
Type of Operation to Perform: udpEcho
Type of Operation to Perform: voip
IP SLAs low memory water mark: 38288719
The device is a Cisco 1841

Integrating windows AD with cisco ACS

hi all i am looking for the requirements and any documents in setting up the acs with windows AD for user authentication.
i am basically testing this.
i am having a cisco switch a switch acs serevr 4.1 and windows xp host and windows 2003 server.
can someone pls tell me the procedure for this on the acs and the AD.
any help would be appreciated.
regards
sushil

hi thanks for the link.
but can u tell me when installing the acs where it asks for slecting the database the acs only or the windows database should we select the windows database.
so when we are configuring the acs for 802.1x authentication and authorisation.
we should select the create the users as in the AD right.but the password for them should be redirected to the AD right.
can u pls guide me on this.
regards
sushil

Integrating Microsoft NAP with Cisco ASA

Hello everyone,
I'm quite new to the Cisco world. I wonder if and how it is possible to marry Cisco ASA with Microsoft NAP (in Terms of VPN Enforcement). Does anybody know some helpful documents? Is an ACS Server/Appliance necessary?
Thanks in advance and kind regards

Hello Jatin,
thanks for your reply.
Microsoft states that authentication via PEAP is necessary for NAP to work:
"One security feature of PEAP is the transmission of Statement of Health (SoH) messages."
(see http://blogs.msdn.com/b/openspecification/archive/2009/06/05/peap-phase-2-encapsulation-examples-for-a-client-authenticating-with-ms-chapv2.aspx?Redirected=true)
However, I found this topic which states that PEAP auth. is not possible with the ASA: https://supportforums.cisco.com/thread/2028742
Is that true?

Cisco LMS 3.2 SYSLOG not storing after 10 days

Hi ,
Im facing one issue with Cisco LMS 3.2
Issue : The logs is generating only for 10 days and post that im not able to see the logs. I have not done any config changes. The only change i have done is i have completely reinstalled the LMS. i did multiple troubleshoot but not able to resolve this isse. It would be great If any some one is able to help me in this isse. Thanks.
Regards,
Juliet

Dear Vinod
Thanks for ur response and the problem has been resolved.
The purge policy was set to 60 days only .The problem in reports viewing setting.
Syslog folder under LMS would store syslog reports of both the device as well as applications for defined folder size , which in your case was 1 MB ( same can be viewed under log generator option). The older reports would get deleted from the folder upon reaching the limit.
The only way to view device syslog is under following option : Reports -> Reports Generator in LMS GUI where we will have to choose syslog with desired attribute.
Regards,
Juliet

Facing issue in integrating with Cisco ISE

We are trying to integrate our product(Cisco Prime Infrastructure) with Cisco ISE for Authentication and Authorizations. We already support PAP/CHAP, and not trying to add support for EAP-TLS.
Currently during our integration, facing TLS payload errors. We are using jradius library for talk to Cisco ISE for authentication and facing the below TLS error in ISE logs. Tried with Cisco ISE 1.2 and 1.3 versions.
Event                                    5400 Authentication failed
Failure Reason                 11500 Invalid or unexpected EAP payload received
DetailedInfo                      TLS packet parsing failed: total accumulated size plus this last fragment size is greater than expected total TLS message size
Any pointers to resolve this problem or any other free java based client library instead of jradius which is tried out successfully with Cisco ISE would also be great.
Regards
Chandrakumar

DECLARE
CURSOR s_cur
IS
SELECT eno FROM emp;
TYPE fetch_array IS TABLE OF s_cur%ROWTYPE;
s_array fetch_array;
BEGIN
OPEN s_cur;
FETCH s_cur
BULK COLLECT INTO s_array;
CLOSE s_cur;
FORALL i IN 1 .. s_array.COUNT
INSERT INTO (select eno from emp_temp)
VALUES s_array (i);
END;
Its working, but not understood the concept.
INSERT INTO (select eno from emp_temp)
VALUES s_array (i);
How it works?

Ask the Expert: C-Series Integration with Cisco Unified Computing System Manager

Welcome to the Cisco Support Community Ask the Expert conversation. This conversation is an opportunity to learn and ask questions about Cisco C-Series Integration with Cisco Unified Computing System® Manager (Cisco UCS® Manager) with Cisco experts Vishal Mehta and Manuel Velasco.
Cisco UCS C-Series Rack-Mount Servers are managed by the built-in standalone software, Cisco Integrated Management Controller (Cisco IMC). When a C-Series rack-mount server is integrated with Cisco UCS Manager, the IMC no longer manages the server. Instead you will manage the server using the Cisco UCS Manager GUI or Cisco UCS Manager command-line interface (CLI).
Cisco UCS Manager 2.2 provides three connectivity modes for Cisco UCS C-Series Rack-Mount Server management. The following are the connectivity modes:
Dual-wire management (shared LAN On Motherboard [LOM]): Shared LOM ports on the rack server are used exclusively for carrying management traffic.A separate cable connected to one of the ports on the Payment Card Industry Express (PCIe) card carries the data traffic.
SingleConnect (Sideband): Using Network Controller Sideband Interface (NC-SI), the Cisco UCS Virtual Interface Card 1225 (VIC1225) connects one cable that can carry both data and management traffic.
Direct Connect Mode: Cisco UCS Manager Version 2.2 introduces an additional rack server management mode using direct connection to the Fabric Interconnect.
Vishal Mehta is a customer support engineer for Cisco’s Data Center Server Virtualization Technical Assistance Center (TAC) team based in San Jose, California. He has been working in the TAC for the past 3 years with a primary focus on data center technologies such as Cisco Nexus® 5000, Cisco UCS, Cisco Nexus 1000V, and virtualization. He presented at Cisco Live in Orlando 2013 and will present at Cisco Live Milan 2014 (BRKCOM-3003, BRKDCT-3444, and LABDCT-2333). He holds a master’s degree from Rutgers University in electrical and computer engineering and has CCIE® certification (number 37139) in routing and switching and service provider.
Manuel Velasco is a customer support engineer for Cisco’s Data Center Server Virtualization TAC team based in San Jose, California. He has been working in the TAC for the past 3 years with a primary focus on data center technologies such as Cisco UCS, Cisco Nexus 1000V, and virtualization. Manuel holds a master’s degree in electrical engineering from California Polytechnic State University (Cal Poly) and CCNA® and VMware VCP certifications. Remember to use the rating system to let Vishal and Manuel know if you have received an adequate response.
Because of the volume expected during this event, our experts might not be able to answer every question. Remember that you can continue the conversation in the Data Center, under subcommunity, Unified Computing, shortly after the event. This event lasts through May 23, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hello Sebastian,
The different modes of connecting C-Series with UCSM come into play depending on the type of infrastructure you already have along with C-Series and NIC model.
Cisco UCS C-Series Rack-Mount Servers are managed by the built-in standalone software, Cisco Integrated Management Controller (CIMC) .
Powerful features provided by Cisco UCS Manager can be leveraged to manage C-Series server by integrating C-Series Rack-Mount Server with UCSM.
This not only gives you rich-feature set but also one management plane to operate UCS-B Series Chassis and UCS-C Series Rack Server.
You will manage the server using the Cisco UCS Manager GUI or Cisco UCS Manager CLI.
Cisco UCS Manager 2.2 provides three connectivity modes for Cisco UCS C-Series Rack-Mount Server management.
The following are the connectivity modes:
• Dual-wire Management (Shared LOM):
Shared LAN on Motherboard (LOM) ports on the rack server are used exclusively for carrying management traffic. A separate cable connected to one of the ports on the PCIe card carries the data traffic. Using two separate cables for managing data traffic and management traffic is also referred to as dual-wire management.
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_0100.html
This mode is recommended when you have C-Server which does not have or cannot support VIC 1225 card (such C-200 server)
• SingleConnect (Sideband):
Using Network Controller Sideband Interface (NC-SI), Cisco UCS VIC1225 Virtual Interface Card (VIC) connects one cable that can carry both data traffic and management traffic.
This feature is referred to as SingleConnect.
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_011.html
This most recommended Integration model when using FEX and VIC 1225 card
• Direct Connect Mode:
Cisco UCS Manager release version 2.2 introduces an additional rack server management mode using direct connection to the Fabric Interconnect.
This mode will eliminate the need for FEX module as Servers are directly plugged into the base ports of Fabric Interconnect
http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c-series_integration/ucsm2-2/b_C-Series-Integration_UCSM2-2/b_C-Series-Integration_UCSM2-2_chapter_0110.html
Please let us know if you need more information. Thank you!
Thanks,
Vishal

Cisco Prime LMS appliance Compatibilty with Cisco Prime NCS

Hi,
Is it possible if we can install Cisco Prime LMS 4.2 in the appliance which is inbuilt with Cisco Prime NCS .
We have PILMS42-1.5K-U license available with us.
Rgds,
Kamal

One can install either LMS 4.2 or NCS on the a physical (software on PRIME-NCS-APL-K9 hardware) or virtual appliance (software installed on customer-provided VM).
The two products (NCS and LMS) cannot coexist on a given appliance instance. This is due to change in the future as LMS and NCS merge under the Cisco Prime Infrastructure 2.0 release but for now they are distinct and separate products with a common approach and similar look and feel but requiring separate servers, whether physical or virtual.
Please refer to the ordering and licensing guide here.

Tutorial: Azure AD Integration with Canvas LMS

Click reply and tell us what you think:
Tutorial: Azure AD Integration with Canvas LMS
Markus Vilcinskas, Knowledge Engineer, Microsoft Corporation

Thanks for this. Do you have a similar set of instructions to use the "use an existing single sign-on" option so we could leverage our Azure Identities but with our ADFS system (we're not currently syncing passwords to Azure AD)?

Afaria 7 SP3 integration with Cisco ISE

Hi,
I am trying to find the configuration procedure that is needed for Afaria MDM to integrate with Cisco ISE 1.2.
1. What service should be installed/enabled?
2. Which port or service path (<IP:port/abc/xyz?>) it will listen for the communication from Cisco ISE?
3. Cisco ISE uses REST API to communicate with Afaria. Does this require REST API installation or service activation?
4. What type certificates are supported in Afaria for this integration.
5. Anything that related to this topic.
Appreciate if someone can provide the configuration procedure or any information possible.
Regards,
Mudasir Abbas

From the user guide it seems that LDAP only allows you to strip the prefix/suffix and can't add the suffix.
http://www.cisco.com/en/US/docs/security/ise/1.1/user_guide/ise_man_id_stores.html#wp1054421
Strip start of subject name up to the last occurrence of the separator
Strip end of subject name from the first occurrence of the separator
Regards,
Jatin
Do rate helpful posts-

Design guide for integrating unigy with cisco HUCS 7.1.1 Environment

Hi,
I have a requirement to integrate unigy dealer board with cisco HUCS environment. please provide if any design and integration document is there.
Regards,
baskaran.M

Fix you contact resolution to your LDAP and you'll get just that, what you're seeing right now is expected as the fact you get JID and not the friendly username, means you're not looking at LDAP.
Right now you're also unable to dial, assuming you have softphone or deskphone control, from jabber as the DNs for the contact, are also brought over with the contact resolution from LDAP.
Make sure you have SRVs, or manually configure the integration in jabber-config.xml.

Integration with Cisco Call Manager?

We have Cisco VOIP phones and we would like to continue managing calls with Cisco Call Manager. We currently have voicemail on Cisco Unity. We currently have Exchange 2010, but plan to start using Exchange 2013 soon.
However, we would like to migrate voicemail service from Cisco Unity to Exchange Unified Messaging and also want to take advantage of most of the voicemail-related features of UM such as voice to text sent to email, voice mail waiting indicator light on
the phones and sending voice mail audio attachments to email.
Is Exchange 2013 Unified Messaging compatible Cisco phones that are managed by Cisco Call Manager?
We have 500 users and 2 Exchange 2010 servers (1 CAS and 1 Mailbox Server). We now have a few Exchange 2013 licenses available in addition to our existing 2010 licenses that are already used on our existing 2 servers. Can we keep the 2 existing
Exchange 2010 servers as they are and create a new Unified Messaging server on Exchange 2013 in the same environment or do we need to upgrade all the 2010 servers to 2013 if we use Unified Messaging on 2013?

Hi Sachin,
We do run a hybrid Callmanager to Nortel Meridian setup (works well).
Here are some great docs;
Cisco Unified CallManager
Case Study: Nortel 61C PBX to Cisco IP Telephony Migration
From this good doc;
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_white_paper09186a00801115e0.shtml
Nortel Meridian PBX and Cisco CallManager Integration
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a008011888c.shtml
Cisco Unified CallManager System Guide, Release 4.2(1)
Cisco DPA Integration
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a008055cd53.html
Hope this helps! Let me know if you need additional info.
Rob

Can i have IVR feature with ccm 6.0.1 integrated with cisco unity connection 2.0.1

Hi
can i have IVR feature with ccm 6.0.1 integrated with cisco unity connection 2.0.1.
And tell me a solution how can i go for IVR with this design.
Thanks.
veera.

Yes, you can have a basic IVR with CUC, no one can tell you how to design your CUC, that's up to you and your requirements.
All you need are call handlers, caller input and greetings.
If you need someone to do all this for you, engage with a local Cisco partner.

Honeywell Integration with Cisco IPT

Hi,
One of my customer has BMS fom Honeywell. He needs to integrate this system with Cisco IPT 8.6.
IP telephony system shall be capable of providing a software adjustable temperature setpoint at each telephony terminal, this point info shall be synchronized with the BMS in order to provide the telephony user the ability to adjust the room temperature setpoint from the telephony set, or from the room wall module, and the final value of the point shall be determined as of the final order received from one of the two destinations.
The link between the two systems, BMS and IP Telephony, shall be in one of the below methods:
•1- Open protocol connection (BACnet, OPC DA, or Modbus)
•2- SDK development tool provided by Honeywell Building Solutions.
How can the above be achieved? What components do i require to achieve the above functionality?
Appreciate your help.

Hi,
I am providing you with the below CUCM interop link, where in different product inetrop testing is done with CUCM and is supported.
http://www.cisco.com/en/US/solutions/ns340/ns414/ns728/networking_solutions_products_genericcontent0900aecd805b561d.html
Please see any of the similiar protocol is used with some other product which is listed here.
Hope it helps.
Anand
Please rate helpful posts !!

Cisco LMS 4.0 Graph some time not coming

I have installed cisco lms 4.0.
I have added 10 devices, previously it was working fine, Since last few days some time syslog and graph are not coming. after every reboot on server it started working. It is happening on daily.plz help me out with permanent solution
and also i have added manualy one device 7609-s router but not able to see cisco view
Error:-
Cannot find applicable device package for 10.133.224.131.
This error could be due to one of the following:
- The device package for this device type is not installed.
- Device support for this device type is not available.
- You are trying to open a component inside a device.
To correct the problem, either install a device package for the device type, or open the parent device to manage the component.
In device attribute it is showing 868 integrated router, I had try to delete and add again but problem is still same...
Windows 2008 r2 standard
RAM-16 Gb, Swap memory 8096

Evrything looks good. Are you able to access LMS in the server itself? Try to install another browser on your server and try to login.
Try both :
http://x.x.x.x:1741
https://x.x.x.x:443
Share NMSROOT/MDC/tomcat/logs/stdout.log and stderr.log.
-Thanks

Integration of SMS with Cisco LMS 3.2

Similar Messages

Maybe you are looking for