Intel 6205 wireless not working with Lenovo W520

Loving the new W520... very fast, if only the wireless would work. Unable to get wireless interface functioning, won't even show up in ifconfig. I've appended requested wireless information, thanks in advance for any assistance.
1) Machine Brand and Model (PC/Laptop):
Lenovo W520
Intel Centrino Advanced-N 6205
Note: Wireless switch on lefthand side enabled, bluetooth led lights up but wireless does not.
2) Wireless Brand, Model and Wireless Chipset:
$ lspci -nn
03:00.0 Network controller [0280]: Intel Corporation 6000 Series Gen2 [8086:0085] (rev 34)
3 ) check interface:
ifconfig does not show wireless
$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
4 ) Check for modules:
$ lsmod
iwlagn 215351 0
iwlcore 139688 1 iwlagn
mac80211 269644 2 iwlagn,iwlcore
cfg80211 167809 3 iwlagn,iwlcore,mac80211
5) Kernel boot messages
$ dmesg
[ 13.497936] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
[ 13.497938] iwlagn: Copyright(c) 2003-2010 Intel Corporation
[ 13.498058] iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 13.498089] iwlagn 0000:03:00.0: setting latency timer to 64
[ 13.498181] iwlagn 0000:03:00.0: Detected 6000 Series 2x2 AGN Gen2a, REV=0xB0
[ 13.499187] lp: driver loaded but no devices found
[ 13.502642] alloc irq_desc for 22 on node -1
[ 13.502645] alloc kstat_irqs on node -1
6 ) Network configuration
$ sudo lshw -C network
*-network UNCLAIMED
description: Network controller
product: 6000 Series Gen2
vendor: Intel Corporation
physical id: 0
bus info: pci@0000:03:00.0
version: 34
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress cap_list
configuration: latency=0
resources: memory:d5300000-d5301fff
7 ) Scan for networks:
not relevant as no wireless interface appears
8 ) Ubuntu Version:
Ubuntu 10.10
9 ) Kernel/architecture (including 32 vs. 64 bit):
2.6.35-28-generic x86_64
10 ) Restarting the network:
sudo /etc/init.d/networking restart
* Reconfiguring network interfaces... Ignoring unknown interface eth0=eth0.
[ OK ]
Additionally, modinfo shows the following:
$ modinfo iwlagn
filename: /lib/modules/2.6.35-28-generic/updates/compat-wireless-2.6.36/iwlagn.ko
alias: iwl4965
license: GPL
author: Copyright(c) 2003-2010 Intel Corporation <[email protected]>
version: in-tree:
description: Intel(R) Wireless WiFi Link AGN driver for Linux
firmware: iwlwifi-4965-2.ucode
firmware: iwlwifi-5150-2.ucode
firmware: iwlwifi-5000-2.ucode
firmware: iwlwifi-6000g2b-4.ucode
firmware: iwlwifi-6000g2a-4.ucode
firmware: iwlwifi-6050-4.ucode
firmware: iwlwifi-6000-4.ucode
firmware: iwlwifi-1000-3.ucode
srcversion: 8F7F4C6196599FCA596C837

Hi  sparhk, and welcome.
One of the Lenovo staff who frequents the forum put out a call to help you in a private forum.  I do a little Linux, so I poked into it.  To my amazement my first Google hit was your thread where you indicate you have solved the problem.  (At least, it _looks_ like you...)
May I respectfully suggest that a post back here indicating success would be a nice touch?  That way anyone who passes by looking for help with this issue will have a better chance of finding it.  For posterity, here it is (see post number 25):
[SOLVED] Intel 6205 wireless not working with Lenovo W520
Glad you got it working,
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc.  The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

Similar Messages

  • S10-3t bluetooth and wireless not working with windows 8

    S10-3t bluetooth and wireless not working with windows 8. I tried everything but doesn't work at all. I don't know where to find the new drivers that are comatible with windows 8 ???!!! please help me to solve this problem because i tried everything....

    Do you still have your windows7 install files ? 
    ( installation image is usually in LENOVO_PART OKRBackup/Factory ) ? I lost them :\
    if yes I fear you have to enable it in win7 and then use it in win8
    http://rzr.online.fr/q/lenovo# g470 s103t (Please Contact me if your s10-3T is booting win7 or support bluetooth, 3g)
    Lenovo S10-3t | Model Name : 0651 | Mfg Date: 2010/06/08
    Lenovo G470 | Model Name : 20078 | M fg Date: 11/03/23 | BIOS: 40CN23WW(V2.09) 06/20/2011 | CPU: i5-2410M | Linux version 3.3.4lenovog470+ (root@lap) (gcc version 4.6.3 (Debian 4.6.3-4) ) #8 SMP Tue May 1 10:23:48 CEST 2012
    OS:GNU/Linux/Debian

  • X3000 wireless mouse not working with lenovo T440 - windows 7

    New mouse of HP x3000 model is not connects with lenovo T440 model which has windows 7 Enterprice edition. What could be the problem. I followed recommented steps.

    Hello @Ilakkuvan,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I have read your post on how your wireless mouse will not work on your Lenovo computer. I would be happy to assist you in this matter!
    Does the wireless mouse work when connected to another computer? Do other USB devices work on your computer? In the meantime, I recommend following the steps in this document on Troubleshooting USB Connections (Windows 7). This should help connect your mouse to the computer.
    Please re-post with the results of your troubleshooting, as well as the requested information above. I look forward to your reply!
    Regards
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • U430 Touch: wireless not working with windows 7

    My friend bought a U430 Touch with Windows 8. He hated Win 8 so I helped him downgrade to Win 7. Now the wireless dowsn't work. Ethernet works fine and we are able to get on the internet, but wireless does not work at all. I've been to Lenovo's site and downloaded the drivers from their support site, but nothing weems to work. Is there a special driver I'm missing?
    Solved!
    Go to Solution.

    It's possible that they are shipping with Intel only at the moment, but the Hardware Maintenance Manual lists two non-Intel cards: a Liteon, and a "non-Intel", whatever that means.
    Just sayin'
    Z.
    The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc.  The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

  • Intel Wimax 5350 not working with windows 7/t400

    As someone who uses server 2008 on my desktop, when i received my t400 a few days ago i balked at the idea of using vista.  so i decided to download and install 64bit windows 7 (from vista 32bit...i did a clean install though...i believe).  i had not heard of anyone having trouble with wireless drivers in windows 7 and indeed intel states on their website that windows 7 will automatically install the drivers for the 5350 wireless card.
    unfortunately, when windows 7 installation was complete the drivers were not installed and i did not have internet access.  so i had to take the usb wireless adapter from my desktop and plug it in to access the internet.  windows update did not fix the issue.  so i installed the visa 64bit intel drivers and windows told me that my wimax device was recognized, the drivers were installed, etc.
    except the wireless card still wouldn't work!  currently under network adapters it is listen as local area connection 2/network cable unplugged/intel wimax link 5350.  i don't understand this...shouldn't it be listed as a wireless network connect as my usb adapter is? 
    i think the problem might be that under device manager, i do not have a driver for network controller, pci serial port, or pci simple communications controller.
    this is quite frustrating and i really regret not having put more thought into this windows 7 installation.
    thanks for the help
    Solved!
    Go to Solution.

    I've got a T400 with a Intel 5350 and Windows 7 x64, I downloaded and installed the
    Intel® PRO/Wireless and WiFi Link Drivers-Only for Windows Vista* (3298KB) and the
    Intel® PROSet/Wireless WiMAX Connection Utility for Windows Vista* 64-Bit (9206KB) from the website listed below. 
    http://downloadcenter.intel.com
    Furthermore, my "Intel(R) WiFi Link 5350" and "Intel(R) WiMAX Link 5350" listed in the "Network Adapters" category, I dont have any "Wireless Network Connect" category at all.
    Hope this helps!
    Message Edited by Aiwi on 07-15-2009 02:04 PM

  • Emagic mt4 and intel iMac does not work with 10.4.5

    Hi there,
    after updating my iMac on 10.4.5 my MT4 does not work any longer. It is still shown in the system profiler! But that`s it! After I`ve installed the latest driver (emagic v1.7), it was not shown in the audio/midi preferences. On my G4 with 10.3.9 it is still working properly. I have tried to use it with Garage Band 3, while I am waiting for Logic Pro 7.2 . It worked in the begining, but now the USB connection on the MT4 does not light up, but the midi devices. My question is: Do I need a driver using Logic Pro 7.2 with an Intel iMac? Includes the update the driver for Emagic MT4?
    thanks a lot for any reply, experiences and clues
    jay markus
    iMac Intel core 20''   Mac OS X (10.4.5)  

    Hi Glyn,
    I will try to get some driver information of apple. Emagic is apple now, so who else could that know?! I use an m-audio fw audio-interface. For that m-audio got a driver and it works by now. Fortunately! I will tell you if apple got a clue.
    Thanks for reply ( So I am not the only one in universe with that problem!)
    Best regards
    Jay
    iMac Intel core 20''   Mac OS X (10.4.5)  

  • Fingerprin​t reader on Lenovo KUF0452 keyboard not working with Lenovo X1

    Hi, I have a Lenovo KUF0452 keyboard with built-in fingerprint reader. Up until two weeks ago I had a two year old X1 Carbon laptop which co-existed happily with the keyboard - I could unlock Windows with a swipe of the keyboard's fingerprint reader. I've now replaced the old X1 with a brand new X1 Carbon and can no longer unlock Windows using the keyboard's fingerprint reader - I just get this error on the Windows 8.1 lock screen: "A match for the fingerprint was not found in the fingerprint database." I have the latest Lenovo Fingerprint Manager Pro installed and have used it to enroll a couple of fingerprints for the X1's fingerprint scanner, but when I try to use it to enroll fingerprints for the keyboard's scanner the app's progress bar doesn't move off 0%, so I assume the app isn't accepting the keyboard's fingerprint scanner as a valid input. The X1 is docked, with the lid shut, so I have no easy access to the laptop's fingerprint scanner which is why I want to use the keyboard's fingerprint scanner to unlock Windows. How can I get the keyboard's fingerprint scanner to work with my X1? Kind regards,

    hi Avikiru,
    Welcome to Lenovo Community Forums!
    Can you try,
       Remove the AC and the Battery
           Hold the Power Button down for at least 15 sec.
                  Reconnect just the AC and see if that'll work
    If not You can contact a Lenovo Support Team or a Local Technician to have the Keyboard connection checked.
    Regards
    Solid Cruver 
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • S10-3 Wireless - not working with Windows 7

    Hi, I bought the S10-3 two days ago and decided to load windows 7 (ultimate). The load was smooth but after I had finished the wireless was not working nut the wireless light on the front of the PC was on. The first strange thing I noticed was Fn5 did not work so the only on/off control I had was on the side switch. I eventually fixed this problem by downloading the driver from the internet , the wireless is the Atheros AR9285. Everything was well and proceeded to download anti-virus and other software.
    Then disaster, during the time of downloading windows had also been doing some updates and when the system restarted there is NO WIRELESS.
    It appears on boot that the "wireless" light indicator is ON and when windows fires up it goes off, I checked in the boot and it is enabled, I checked the driver again but it is OK but windows says it is not switched ON but I have checked the physical switch and it is ON.
    Any ideas appreciated.
    edit : correct machine model in postname 

    Hi and welcome, if all possible is switched on.. did you install the lenovo energymanagement ?
    where you can switch (softwarebased) seperately wireless devices... if wifi still isnt work...
    you have to bite in a sour apple and install windows 7 from a scratch again ... then first update all via windows updates , then ... install the lenovo energymanagement... , then, look in devicemanager if there is some questionmark ...  in normal case there is no need other driver to install...
    and all should be working... simply install a antivirus-program.. and all your need other personal stuff...
    sincerely KalvinKlein
    Thinkies 2x X200s/X301 8GB 256GB SSD @ Win 7 64
    Ideas Centre A520 ,Yoga 2 256GB SSD,Yoga 2 tablet @ Win 8.1

  • G505s - Touchpad hot key function not working with lenovo driver

    I'm using windows 8.1, Lenovo G505s laptop. Recently I got replacement from Lenovo regarding touchpad after that this Fn(F7) touchpad enable/disable not working. This is happening only when I installied touchpad driver provided by lenovo and works well with standard microsoft driver (Ofcourse, no multigesture support with that driver).
    We perfomed following operations:
    1. HotKey mode enable/disable in BIOS
    2.Reinstallation of OS
    3. Reinstallation of driver(manually)
    All cases with microsoft driver this function working but with touchpad driver it is not working. It's almost 90days (88thday) daily contacting both Lenovo customer support and service center people but no use.
    If anybody having this problem and have a solution please share! (My machine under warranty!)

    hi phani_kumar,
    It's likely that you have a Synaptics driver (you can verify this by its hardware ID or use a utility software like AIDA 64 Extreme Edition).
    - Link to picture (Synaptics)
    - Link to picture (ELAN
    If you're unable to install the driver below, can you follow this guide on how to disable driver signature enforcement then try to reinstall the driver again and observe if you can now toggle the Fn+F6.
    Windows 8/7/XP/Vista 64/32-bit Edition v17.0.19
    All Languages
    118.1 MB zip
    Regards
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Intel 5300 wireless not working (iwalgn)

    $ lspci | grep -i net
    03:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 (rev ff)
    $ uname -a
    Linux westley 3.1.2-1-ARCH #1 SMP PREEMPT Tue Nov 22 09:17:56 CET 2011 x86_64 Intel(R) Core(TM)2 Duo CPU T9400 @ 2.53GHz GenuineIntel GNU/Linux
    My wireless card worked perfectly for quite a long time, but lately it's been a bit flakey. Coming out of standby often causes it to fail, and rebooting will sometimes, but not always, fix the problem.
    The indicator light won't come on, and trying to bring the card up manually gives this:
    The laptop's a T400, if that's any help.
    $ sudo ifconfig wlan0 up
    SIOCSIFFLAGS: Connection timed out
    And dmesg looks like this:
    [34123.748035] iwlagn 0000:03:00.0: L1 Enabled; Disabling L0S
    [34123.750915] iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
    [34123.750915] iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
    [34123.784661] iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
    [34123.798853] iwlagn 0000:03:00.0: Radio type=0x0-0x2-0x0
    [34123.802162] iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
    [34123.818812] iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
    -- snip --
    [34124.383259] iwlagn 0000:03:00.0: MAC is in deep sleep!. CSR_GP_CNTRL = 0xFFFFFFFF
    [34129.396705] iwlagn 0000:03:00.0: Could not load the INST uCode section
    [34129.396712] iwlagn 0000:03:00.0: Failed to start RT ucode: -110
    [34129.396739] iwlagn 0000:03:00.0: Unable to initialize device.
    Any help would be greatly appreciated.
    Last edited by stillinbeta (2011-11-28 04:18:20)

    Until you get it fixed, you can tell pm-suspend to unload the wireless driver before suspending, then loading it again after resuming?

  • The zoom function is not working with lenovo A700 computer

    I have a lenovo A700 desktop computer with a touch screen interface. I recently downloaded the newest version of Firefox (4.0.1) and now the touch screen zoom in/out function with webpages is not working. This function is working with IE8 on the same computer so there seems to be something wrong with Firefox. It was working with the previous version of Firefox as well. Please help, thanks.

    jotan832,
    Have you tried restoring the iPhone and setting it up as a new phone? Sometimes these issues can be software based. More information on the restore process can be found here: http://support.apple.com/kb/HT1414
    To set up appointments for the Apple Store online, visit http://www.apple.com/retail/ to locate your store website, then choose the Concierge.
    Hope this helps,
    Raleigh

  • Fingerprint reader on Lenovo KUF0452 keyboard not working with Lenovo X240

    Hi,
    I have a Lenovo KUF0452 keyboard with built-in fingerprint reader. Up until a month ago I had a Lenovo X220 laptop which co-existed happily with the keyboard - I could unlock Windows with a swipe of the keyboard's fingerprint reader.
    I've now replaced the X220 with an X240 and can no longer unlock Windows using the keyboard's fingerprint reader - I just get this error on the Windows lock screen:
    A match for the fingerprint was not found in the fingerprint database.
    I have Lenovo Fingerprint Manager Pro v8.01.35(x64) installed and have used it to enroll a couple of fingerprints for the X240's fingerprint scanner, but when I try to use it to enroll fingerprints for the keyboard's scanner the app's progress bar doesn't move off 0%, so I assume the app isn't accepting the keyboard's fingerprint scanner as a valid input.
    The X240 is docked, with the lid shut, so I have no easy access to the laptop's fingerprint scanner which is why I want to use the keyboard's fingerprint scanner to unlock Windows.
    How can I get the keyboard's fingerprint scanner to work with my X240?
    Kind regards,
    /Neil 

    hi jenniby,
    Welcome to Lenovo Community Forums!
    I believe it is the Lenovo B570 you're saying, 
    Try doing a power drain,
        Remove AC adapter and Battery, then hold down the power button for at least 15 sec. this will drain off the power from the MOBO.
    Reconnect everything and see if that works,
    Also try using an external Keyboard to test out the Windows.
    If that did not work I suggest Calling Lenovo Technical support for Hardware Concern.
    Regards
    Solid Cruver
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • MBA bootcamp intel hd 3000 not working with projectors

    If I use the mini display to DVI to connect to a projector, it will work if the displays are mirrored, but if I extend the display, where the projector has a higher resolution, the projector display will have artifacts, noise, and if it has a lot of pictures or videos on the screen, the display sometimes stops working. Even if i set the display resolution to match the same as the laptop, I still get noise and artifacts unless I mirror the displays. Any ideas?
    Then if I true to use the mini port VGA to the same projector but Windows won't recognize the projector. I've seen several reports about this. I have the latest Intel graphics driver and my bootcamp partition is running Windows 7, fully updated and patched. I've read some people are suggesting buying a 3rd party mini port to VGA connector to solve this problem. But can anyone confirm?
    Lastly, this seems to only happen with my MBA with the Intel HD 3000 graphics. I have another MBA with the Nvidia 300M and the mini port to DVI works fine.

    Hi all,
    I have same problem with my MBA 13", can't project to projector & some LCD TV via using Mini VGA port in Windows 7. Any solution and pls help.

  • Imac intel internal speakers not working windows8

    Imac intel internal speakers not working with windows 8 external and head phones work just fine

    Macs don't support Windows 8 at this moment. Wait until Apple launches drivers for that new Windows edition

  • The volume keys on my Logitech K760 wireless keyboard do not work with my 2.3 GHz, Intel Core i5 Mac mini which runs Mac OS X 10.7.4. Anyone know how to correct this without having to re-code firmware?

    My first post to the Apple Support Community so it looks like all I wanted to know is covered in the title. The research I have done led me to solutions that I am not comfortable trying for fear of irreparably damaging my keyboard and/or Mac mini. Does anyone have a simpler solution? Please? Hellooooo?
    Just in case the title is too long to show, I have re-pasted here:
    The volume keys on my Logitech K760 wireless keyboard do not work with my 2.3 GHz, Intel Core i5 Mac mini which runs Mac OS X 10.7.4. Anyone know how to correct this without having to re-code firmware?

    BDAqua wrote:
    Hello & welcome to the Forums!
    I think Spark cured this for another person and the same problem...
    http://www.shadowlab.org/Software/spark.php
    http://scripts.sil.org/cms/scripts/page.php?site_id=nrsi&id=ukelele
    http://doublecommand.sourceforge.net/
    Thank you for the response. Unfortunately, I could not figure out how to work the above applications. I thought that i had managed to assign the appropriate function keys in Spark to their volume counterparts, but it had no effect. Below is a screen shot. Do you see anything amiss?

Maybe you are looking for