Intersense Inertiacube, IC3, ITrax2, InterTrax2 -- third party driver for Labview

Hi,
I've been attempting to use the third party driver located at:
http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=1540162FC7953043E0440003BA7CCD...
to communicate with an Intersense Inertiacube via Labview 8.2.  It does work, but it causes sporadic Labview crashes as well.  Typically Labview will crash in one of the following scenarios (in order of frequency):
- upon editing any VI after running and successfully stopping the Intersense communicating VI
- upon stopping the Intersense communicating VI (not the halt button, but a healthy stop)
- upon starting the Intersense communicating VI (very rare, and typically only after several successful starts/stops of the VI)
My hunch is that this is a memory management issue related to the third party DLL wrapper (isense_dll_wrapper.dll).  Does anyone have any experience with this?  Anyone know the history of who wrote the wrapper?  Is the source code available?  Is there a way of having the DLL open/run in its own memory space, separate from Labview's memory space? 
Is there a way of having the VI run in a separate memory space from the rest of Labview (so at least if it does crash it won't take all of Labview with it)?
Thanks for your time,
~ Jay

If anyone knows how to contact Sacha Emery, ATE Systems Engineer @ NI, he may have more information regarding this.  (He may even have the DLL wrapper source code.)  His name is in the ITrax2 Readme.txt file as the creator.
~ Jay

Similar Messages

  • Looking for third party driver for Bentley Nevada 208P data acquisition unit.

    We have a Bentley Nevada 208P data acquisition unit used with their Adre system (software/hardware). We would find it benifitial to utilize it on another application other than monitoring proximitors, and do some calculations on the voltage signals received outside Bentley's Adre system software. We are using LabView on other applications. Has anyone tried this?

    From what I can find about this instrument it looks as though it communicates via Parallel port. I don't think NI has anything which is specific to this instrument, but if Bentley Nevada publishes the command set/communication specs you could probably use VISA to communicate with it (unfortunately they won't allow access to their manuals online without a password so I can't find out anything more specific).
    Best of luck,
    Ryan K.

  • What third party drive do I use to connect my umi-7764 to a phytron stepper motor (zss66)

    I would like to connect my phytron stepper motor (zss66) to my UMI-7764, do I need a third party drive ?
    And if i need one, which one ?
    Thank !
    Seb (I am french so if you want to aswer french, let's go )

    Sebastien,
    l'UMI 7764 n'est qu'un bloc de connexion. En aucun cas celui ci ne délivre de puissance. Donc il vous faudra nécessaire un bloc puissance entre l'UMI et votre moteur. L'UMI 7764 ne délivre aucune puissance.
    (N'oubbliez pas d'aimenter l'UMI avec une alimentation 5V externe. Ce 5V est à connecter sur le connecteur situé au debut du boitier).
    National Instruments fourni des drives (MID 76XX)dont les specs sont limités en courant. (Elles sont affiché dans le lien ci dessous). Dans le cas de l'utilisation d'un drive NI, il n'est plus nécessaire d'utiliser l'UMI 7764.
    Le choix de votre drive se fera en fonction du nombre de phase de votre stepper, et de son courant nominal.
    Voici un lien sur lequel vous trouverez une liste de drive pour stepper. (Voir
    le bas de la page web)
    http://www.ni.com/devzone/advisors/motion/driveadv​isor.htm
    Je ne connais pas les spec de votre stepper, mais si vous désirez l'utiliser avec un UMI 7764, le plus simple serait de contacter la fbricant de ce moteur, et d'obtenir une liste de drive que celui conseille.
    Raphael TILLET
    Ingénieur Application
    NI FRANCE
    Cordialement,
    Raphael T

  • After upgrading to OS Mavericks, I realized that the Partition for Windows is gone. I have really important data on this drive without a back up. Is there any way I can get this data before reformatting. Is there any third party software for receiving the

    After upgrading to OS Mavericks, I realized that the Partition for Windows is gone. I have really important data on this drive without a back up. Is there any way I can get this data before reformatting. Is there any third party software for receiving the data or any possible way? Money is not a limitation to this fix. Please help!!!

    sure pretty simple.  make a backup of your current settings
    http://support.apple.com/kb/HT1766?viewlocale=en_US
    then restore device from old backup you need pics off of
    then import pics to computer
    http://support.apple.com/kb/HT4083
    you may need to save pics to camera roll first
    then restore the new backup and sync pics back to phone via itunes
    Peace, Clyde

  • Motion control: PXI 7350 controller and UMI 7774 to interface with third-party driver UDK5114NW2

    Dear community,
    This is about Motion control in Labview: I try to control a step motor by using a PXI 7350 controller and UMI 7774 to interface with  third-party driver UDK5114NW2. The problem is 5 Disable LEDS on UMI 7774 board always lit even when I check "enable" on "Motion I/O setting" in configuration of PXI 7350 motion controller. Furthermore, when I start to control step motor, it is not working and I found disable LED on UMI board still lit. I don't know how to solve this problem. Can someone help me to figure out? Thank you in advance!
    Hau Nguyen.

    Dear Community,
    I said wrong, 4 disable LEDS on UMI 7774 Board instead of 5 as my previous post. Why nobody help me to solve this problem. I can not turn off disable LEDs on UMI 7774 Board so I can not start the strp motor. Please help me!
    Hau Nguyen. 

  • Disabling a Third Party Drive/Moto​r thru a Relay

    I can’t seem to get my INHOUT signal to disable my drive/motor.  I have the PCI-7342 Stepper/Servo Motion Controller with the UMI-7764 connected to a third party drive and servo motor.  My third party drive requires a constant 24 volt signal to enable my drive/motor.   I have the INHOUT connected to a relay in order to control this 24 volt signal.  When there is 5 volts at my relay this will enable my drive, when the 5 volts goes low then my drive will be disabled.  I have the drive wired up per the attached schematic.  Any suggestions would be appreciated.
    Thanks,
    Nick Argyros
    [email protected]
    Nick Argyros
    Interconnect Devices Inc.
    Electrical Test Engeiner
    [email protected]
    Attachments:
    Motor Wiring Diagram.pdf ‏131 KB

    If you use the source current of the INH output it probably will not be able to drive a 5V relay. Jochen's calculations are valid for the limiting current, i.e. the current where the output voltage will be zero. With a resistive output the output voltage will depend on the current needed by the relay coil and will never reach 5V.
    It is better practice to use the 64mA sink capability of the INH output. But of course in this case the relay will be activated when the output is low. In your case you may wire the relay between +5V (do NOT use the +5V pin of the 734x connector!!! - you may use a +5V terminal of the UMI box provided your UMI power supply can supply the UMI box plus the relay current) and INH, and use the N.O. contact of the relay.
    If this is not desired I would suggest to add an extra output transistor (any small signal transistor can sink 100mA or more) connected as an inverter or a driver IC such as an ULN2803. A single transistor has a saturation voltage of less than 0.5V, and most, if not all, relays rated at 5VDC will switch reliably at 4.5V. Check the relay specs for the 'must on' voltage.
    Never, I said NEVER, connect a relay to a semiconductor device without a snubber diode. The diode should be connected across the coil terminals (and close to them), with the cathode to the (+) terminal. It will short the inducted high voltage when the relay is de-energized. Some relays have integrated snubber diodes.
    Also, I see from your diagram that the emergency switch can be operated at a certain relay position only. At least in Germany this would be illegal since the emergency switch has to be independent from any other control circuitry.

  • Integrate project open (third party tool for time sheet management) in EP

    Hello Experts,
    I have third party tool for time sheet management (Project Open) and EP7.0 SP17. I tried to integrate third party tool with portal by using the App integrator. But it is not working properly. Again and again its asking authentication. I followed same steps to integrate this tool by using App integrator in portal.
    we filled the system properties Server name is projects.company.local and Web Application URL is /intranet/.
    What i made mistakes in this, please help me.
    Regards
    Kumar

    If anyone knows how to contact Sacha Emery, ATE Systems Engineer @ NI, he may have more information regarding this.  (He may even have the DLL wrapper source code.)  His name is in the ITrax2 Readme.txt file as the creator.
    ~ Jay

  • Third party plugin for premier pro cs6

    I installed a third party plugin for premier pro cs6 on my mac and it's not loading... How can get premiere to see it in the program?

    hi todd,
    cart in front of the horse syndrome - wrote BEFORE reading the article. sorry ;-)
    am coming from 10 years of vegas, unhappily so, but at my age 60+, i'm wary of anything new....

  • How do I allow third party cookies for a website and how do I turn off pop-up blocker?

    How do I allow third party cookies for websites and how do I turn off pop-up blocker?

    Allow third party cookies at Safari > Preferences > Privacy > Block Cookies - "Never".
    Turn off the pop-up blocker at Safari > Preferences > Security > Block pop-up windows = unchecked

  • How do you add a third party sensor to LabVIEW for Lego Mindstorms​?

    I recently purchased an IR Sensor from Mindsensors (DIST-Nx-Long-v3) which I need for a SLAM (Simultaneous Localization and Mapping Application) that I am developing using the LabVIEW for Lego Mindstorms software.  I installed the Mindsonsors IR Sensor, and it works under NXT-G and RobotC, but am having trouble finding a way to get LabVIEW for Lego Mindstorms to install the sensor.
    The Mindsensors website gives the following instructions for installing the IR Sensor:
    1.Unzip the folder mindsensors.com LVEE
    2.Open a blank vi in LVEE
    3.On the Block Diagram Go to Tools->Advanced->Edit Palette Set...
    Unfortunately, on the Block Diagram of the LabVIEW for Lego Mindstorms, there is no "Advanced->Edict Palette Set" under Tools.
    As an alternative, I consulted the documentation that came with LabVIEW for Lego Mindstorms.  The Schematic Editor of LabVIEW for Lego Mindstorms lists several sensors, i.e. the Lego Mindstorms sensors and several Hi-Teach (HT) sensors, but there are no procedures listed in the documentation for adding other third party sensors to the Functions Palette.
    So, how does one go about adding a third party sensor to LabVIEW for Lego Mindstorms?

    Hi Ethan,
    As you can see from my Word document, I am a little light on the proper terminology.  That's because LVLM comes with inadequate documentation.
    I have already followed your recommended protocol for installing a 3rd party sensor (in fact, its the protocol recommended by Mindsensors) with the application set in the Remote Mode (.lvrbt), and it does create a sub-palette with all the Mindsensors functions on it.  But when I drag the Mindsensors icon to the Block Diagram and select "Distance Sensor," the Distance Sensor (an IR sensor) doesn't work (even though the Mindsensor's Distance Sensor does work with NXT-G, RobotC and LVLM under other circumstances (see below)).
    If I repeat the above process with the application set in the Direct Mode (.vi), I also get the sub-palette with all the Mindsensors functions on it.  When I drag the Mindsensors icon to the Block Diagram and select "Distance Sensor," the Distance Sensor does work.
    What I need for my mapping application is for the Distance Sensor to work in the Remote Mode.  I called NI tech support and the first engineer told me to simple drag the Mindsensors Functions (.vi) onto the Block Diagram.  I did this, but when I selected the Distance Sensor, the icon appeared, but the sensor did not work.  Since I have no idea what's under the hood of the vi or a function, I assumed that simply dragging the vi/function onto the desktop didn't install the vi/function properly.  I went back to the Applications Engineer, and he confessed that he did not understand the LVLM product.
    My frustration is being punted to new people, none of whom so far (other than you, of course) understand LVLM.

  • Is there any third party software for itunes that will do this:

    Is there any third party software for itunes that will organize the browser window. Ideally I would like the third browser window (album name) organized by "main albums" "compilations" "bootlegs" "singles"
    It would look like this for the Beatles
    Main
    1963 Please Please Me
    1965 Help
    etc.
    Compilations
    1970 Red Album
    1990 Greatest Hits
    etc.
    Bootlegs
    1985 Ultratrax 1
    etc.
    CD Singles
    1999 Whatever
    This info would be marked on either the info or option tab when labeling.
    If this has not been made, one of you nerds should make it, it would be great and you could charge $3 for it and I buy it. and so would 100,000 other people.

    If you haven't already, try looking through the Apple Downloads specifically for iTunes.
    http://www.apple.com/downloads/macosx/ipod_itunes/
    There might be something there that is at least similar to the app your looking for.
    edit: There is one shareware that is an iTunes plugin called Multi-tunes. With it you can create multiple iTunes libraries, one library called "Main" one called "Bootlegs" etc, and Multi-Tunes will allow you to quickly switch between them from within the iTunes window. Not exactly what your looking for but close.
    http://www.apple.com/downloads/macosx/ipoditunes/multitunesdavidcaldwell.html
    Message was edited by: Zookalicious

  • Interface or Third Party Software for viewing SAP Org. Structure in SAP

    Hi All:
    Has any one used a third party software for viewing the SAP Organizational Structure in portal (for MSS).
    Or has developed a custom java iview that would display the org. structure in Portal. (EP 6.0)?
    Thanks

    Yes. I have seen it....with Visio. Sadly, No. I do not have the technical details. Sorry.

  • Access to my Office 365 third-party app for external user : "a User account is not registered for the account"

    In my third-party web application of Office 365, I want to have access to the contacts, events and emails of all the users from the organizations who installed my app. The thing is I don't want that all these users have to grant me access, I just want one
    admin of the org to grant access for my app and then be able to retrieve the data I need for all the users.
    To test for one organization, I logged in as the admin and proceed to the Oauth2 authentication to retrieve the access token and in the first request (the GET one to retrieve an authorization code) i add the parameter
    prompt=admin_consent.
    With this access token, I can access the data (emails, contact, event) of the admin
    for instance for the contacts
    uri: https://outlook.office365.com/ews/odata/Users(adminemail)/Contacts
    but not the data of the other users of this org with this uri
    uri: https://outlook.office365.com/ews/odata/Users(useremail)/Contacts
    The only thing I can do is retrieve an access token for each user but it supposed that each user has to authorize the access to the app but it's very cumbersome. So, i don't see what enables the parameter prompt=admin_consent and how to use it. Does anybody
    know what it does?
    And my question is: how can I do to access the data of all the users of one organization when the access has been granted by one admin?
    Thank you!

        
    This was answered on StackOverflow by Dushyant Gill.  http://stackoverflow.com/questions/25316175/access-to-my-office-365-third-party-app-for-external-user-a-user-account-is-n/25316678#25316678
    You are sending the OAuth request to a tenant specific endpoint of Azure AD. Note the {key_provided} part of your Url - that part represents the tenantid or a registered domain name of an Azure AD tenant. Azure AD throws this error is the user signing in
    is not a user in that tenant.
    Multi-tenant applications like yours have two options:
    Perform home realm discovery yourself and send the SSO request to the correct tenant-specific endpoint of Azure AD: when a new Azure AD organization signs-up for your application, record its tenant ID, and registered domain names. On your login page, ask
    the user for their email and try to discover what Org they belong to using the suffix the email.
    Use the common endpoint of Azure AD. Instead of the {key_provided} part of the URL, use 'common'. In this case Azure AD will determine the user's tenant and sign-in the user. The token that your application will receive will still be from the user's tenant
    (iss claim).
    2 is more convenient for apps. However #1 has an advantage when the user's Organization has customized their sign-in page with the company logo etc - in the case of #1 the user will directly be taken to the customized and familiar sign-in page.
    I recommend a combination of the two: try determining the user's organization and sending them to the tenant specific SSO endpoint. If you're not able to - send them to the common endpoint.

  • Third Party Integration for Template Based Hire in PS 9.1

    Hi All,
    I am implementing template based hire on PS 9.1.
    I am receiving the applicant details from a third party vendor in a xml message.
    Requirement is to insert the applicant details into template based hire records (HR_TBH_HDR and HR_TBH_DATA).
    I am able to subscribe the field values from xml message. But facing the problem while inserting the values into base records.
    I am trying to use Component Interface on HR_TBH_JOB component. The pages on this component are dynamically build and so the records.
    If anyone has worked on the third party integration for Template Based Hire in PS 9.1, please let me know your suggestion for insertion into template based hire records.
    Thanks,
    Vijay

    Hi Michel,
    I am not getting any error message as I haven't completed the coding yet.
    I will go more on the technical stuff so that the issue will be more clear.
    I am using the Integration Broker setup to receive the xml message from third party.
    I have written the app package and added that as handler into the service operation. as of now I am able to subscribe the xml message. I am having the field values into the variables.
    For insertion of those values into template based hire (TBH) records (HR_THB_HDR and HR_TBH_DATA) I created a new CI on HR_TBH_JOB component.
    But when I analysed this component I came to know that Pages, Sections on the Pages and the fields of the sections are dynamically build based on the Template.
    On HR_TBH_DATA page PeopleSoft is using derived record (HR_TBH_SCR_WRK). Field values are assigned to this record fields bsaed on the section of the template.
    Here is issue I am facing while coding. As there is only one record (HR_TBH_SCR_WRK) to store the all the values from the template, I am not able to understand that how to assign the variables to CI variable. I am looking for the logic, so that the CI will work normally.
    If you have any sugestion to insert the data into TBH records other than using CI, will be appriciated.
    Thanks

  • Developing Third Party Connectors for the Universal Worklist

    Hi,
    We need to develop a third party connector for the Universal worklist.
    In order to retrieve the workflow items we want to use a web service that will be developed according our needs.
    The documentation that I found regarding the UWL states that in terms of connectivity we can use Web based protocols such as HTTP and Web Services, but i couldn't find any example for this, besides the SONIC.
    Has someone already developed a third party connector? Examples?
    Thanks in advance.
    Best regards,
    José

    Hi,
    Have a look at these PDFs...
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/405729e9-314f-2a10-eab6-fcebe6fe8cba
    http://help.sap.com/javadocs/nwce/current/uw/UWL%20Custom%20Connector%20API.pdf
    Regards,
    Srinivas.

Maybe you are looking for