Invalid Node structure/ computer running slow?

Hi everyone,
I recently dropped my even a couple of drops of diet coke near the DVD drive of my MacBook (2009).
Turned it off immediately and turned it upside down for a bit. Tune it back on and it worked fine. However, the second time I turned it on it wouldn't go past the login screen. Turned it off as then on again, and started up fine. Ran a disc diagnostic and it gave me the invalid node structure message. From there it started to run slow so I shut it off again. Haven't turned it on since. I'm thinking of taking it in to a shop since I don't want to mess with it anymore.
Is there any easy fix to this? If my hard drive is messed up, can I recover my data? I've never backed up (I know, I know..) so needless to say I'm a little stressed.
Thanks!

That does sound stressful. Sorry to hear you have had these problems.
The good news is that you can probably get your data back. Follow the steps in this document to remove the hard drive from your MacBook. Put the hard drive in an enclosure - you can get these for about $10-15. Connect the hard drive to another Mac and see if it shows up on the desktop. If it does, extract the data.
After that, take the whole thing in to a shop to have them see if they can correct the liquid damage. This may or may not work.
Best of luck.

Similar Messages

IMac Won't boot...Invalid Node Structure

My iMac is just...screwed up. It is a 2008 intel iMac that had worked fine for the last four years until lion. Everytime there was and update or I rebooted, my Mac would freeze at some point of the login. A permission repair or just repair disk would solve the issue an everyone and a while, a restore from backup. Recently my Mac started to slow down to the point it froze for several hours and force quit would never open. I held the button and since then I have been in trouble. The repair permissions had a ton of errors but successfully repaired. But when I repaired the disk, it's hit a couple of errors but ultimately failed right after "Invalid Node Structure" that error has been consistent every time I have attempted a fix and it failed.
I tried restoring from a backup to no avail. Then I wiped the drive and installed Lion (after a convienient 5 hours download) an it booted. I tried using it but it was extremely slow, let it sit over night and came back to it frozen. I had assumed it was slow due to indexing but after 12ish hours this didn't solve the issue. I clicked the apple button and it took a while to finally show up an restarted. Fro
There is wouldn't complete the boot. Froze at the apple logo or white screen with spinning mouse. Left that for several hours and stayed there. Tried repair and same issue. "ivalid node structure" redtating aftet that it just reboots and turns off a little bit after the chime. I have tried everything I could find on different forums without any success. I tried single user mode with the fsck commands and that failed also. I downloaded lion and made a recovery flash drive from another computer. I have since installed several new installations of lion after an erase and repartition. I took it to the apple store and they installed a fresh install of lion and it worked for a day then slowed down and froze. I would like to try everything possible before claiming the hardrive dead. Any other suggestions? (
I forgot to mention I have done PRAM resets in between the events I described as well as the SCM i think reset by unplugging. I have left it unplugged for over 12 hours, also have taken out all peripherals minus keyboard and mouse.

Oh I forgot to add, don't restore from TM or reverse clone, your data might have been messed up, rather cherry pick your good files from backup.
About much would a fix/Harddrive replacement cost?
You might want to get a estimate from Apple, while inside they can clean the filters and run a check.
If it's too much for you, then there are online services
OtherWorld Computing can replace the drive in iMac's
the new 2011's have the certain Apple drive heat for iMac software, not 2009, my mistake.
http://blog.macsales.com/10146-apple-further-restricts-upgrade-options-on-new-im acs
you might find a local service, Apple reseller might do it too, save the shipping costs.

Power Mac G4 - invalid node structure

I am hoping someone can help me. I have a Power Mac G4 - 933....we had a power outage and the Mac would not turn on...the power light lit up when pressed but the computer wouldn't boot...I reset the PRAM and all was good...except a file I had was corrupted and couldn't be opened....after that, a month later, another power outage. This time I had more trouble as resetting the PRAM didn';t work...I reset the logic board (taking out the battery for 30 minutes then replacing) and that didn't work either...I tried several combinations of the above to no avail...I finally took out the battery for over and hour, powered up the computer without the battery and it started...so the battery was corrupted. I replaced the battery (correct one of 3.6 volts) and the computer fired right up. I ran disk utilities to see if all was okay. Checking preferences was fine but when I tried to verify, Disk Utilities came up with the message that it could not complete verifying and that it found "Invalid node structure" and that it could not repair the disk. I then tried fsck to repair and to no avail...fsck gave me several messages depending on the repair options I tried including one that included that the problem was in "memory 4, 23412"....it said it could also not repair due to "os/10 i/o error" and the second run I took at it with a different method told me there was a problem with "DIMM 2/J23 memory"...Apple's website says that if I get an uprepairable message from disk utility that I should back-up, erase and do a clean install...but with these messages indicating the problem is in the memory, since the battery runs the memory, could it be in there instead? ...of important note, I do not have the original install disk...the operating system running it is Tiger 10.4.11...I don't have the orignal disk and I have an empty 10.5 Leopard disk box with no idea where the disk is...I have snow leopard, but that cannot be installed on the G4....after running the last fsck attempt, the computer shut down and is back to only having the power light lit when pressed but no computer booting...where should I start/what do I do? I am hoping you all have good suggestions for me because some of my files were bnot backed up (I know...don't judge) and I got them onto a flashdrive right before the computer went down again, but I have no idea if they took,...further, I love this old dinosaur...

Hi, only thing I've seen repair that is DiskWarrior, you'd need an older version...
http://supportdb.alsoft.com:591/FMPro?-db=alsoftsupport&-lay=main&-max=15&-forma t=AlsoftSupport-qa.html&-script=counter&-token=177&-Skip=96&-find
But it does sound like you have some bad RAM, but have you blown the dust out yet & tried reseating the RAM?

Invalid node structure. Free solution!

Invalid node structure. Free solution! Jan 2007.
Disk problem on an Intel Core Duo Macbook with 1.25 gig RAM and updated to OS X Tiger 10.4.8
Background.
About a month ago I ran into a problem with expose behaving oddly and after posting a question on this forum, the very helpful Dr Smoke advised me to clear my caches and to run 'repair disk.' from the installation CD. (This because I reported that a couple of times I had to do a hard reset.) I got expose fixed but discovered that my disk had serious errors in the directory structure, reported as "invalid node structure," and which Disk Utility could not repair. The laptop was running perfectly but several people posted advice that I should not leave this problem unattended to. Reporting this crisis again on the forum I was advised to buy Disk Warrior for a whopping $100 for what might be a once in a lifetime problem -or else I should back up my data and re-install everything. And I thought the Mac was more stable!! Up to 6 months ago I was a Windows user who often had such problems with the FAT but I was always able to cure them with Checkdisk or Scandisk. In fact MS Windows repaired it automatically after a hard reset. I feel that it is most unfair for Apple to not provide an effective utility to correct this kind of disk corruption. They bundle wonderful programs like iPhoto and iWeb but leave you in the lurch with a fundamental disk problem. With help again from Dr Smoke, I made my firewire disk bootable for Intel Macbooks (must be partitioned with the "GUID" option selected) and searched the forums for a way to get going again without forking out $100. I wouldn't mind if it was a program that did other useful jobs like on-the-fly partitioning but it was going to be an overkill for me. Learning a little from each of several other posts (sorry I didn't record the links) I put together the following solution which is easy to execute and the time consuming elements can be left to run at night or when away from the computer. You may see possible short cuts as you read through to make it even simpler, but here is my full story! Actually I was travelling around Eastern Europe and couldn't easily get disk Warrior or Tech Tools sent to me. I needed to find a solution from reading advice and downloading disk utilities off the Web.
I have a 40 gig ext. disk, mounted in a "hotdrive" enclosure which is useable either as firewire or USB 2. http://www.byteccusa.com.
My Bacbook disk is 60 gig but only 25 gig was in use.
My Macbook was up todate with every part of OS X including the firmware. except for Garage band which I do not use.
Step 1a. I downloaded 2 free disk cloning programs - Carbon Copy Clone and SuperDuper. I preferred the latter. Step 1b I read about Migration Assistant - part of OS X Tiger.
Step 2. I partitioned the Firewire disk in two (32 and 8 gig) for future convenience, and zeroed the disk after Dr Smoke's advice.
Step 3. I installed the basic OS X package onto my 8 gig "Firewire 2" using only Install (DVD) disk 1 which takes up less than 5 gig. (In Setup one chooses to not install the additional programs - iPhoto etc.) I checked that I could boot from it and that it was healthy by running "verify disk" when booted from the internal hdd.
Step 4. While booted from my internal HD, I cloned Firewire 2 onto Firewire 1 (32 gig) I verified the disk (no problems) then booted from it and assured myself that I had a fully working copy of OS X.
Step 5. I booted from firewire 1 and used Migration Assistant to import EVERYTHING - files, programs, the lot, from my internal HDD with the node structure problem. My firewire disk was now 25 gig the same as my internal HD. It had now two users, both shown as administrators. I booted to my newly-imported user ID - the original one that was on my internal HDD. The only problem reported by Migration Assistant was that Missing Synch for Palm might need to be re-installed which would not be surprising given what it does. Later when all was done, I discovered that the migrated programs had been placed in a folder on my desktop so I opened it and moved them all into the 'normal' Applications folder created by my new basic install. (Some programs don't like running from anywhere other than the Applications folder.)
Step 6. I worked from Firewire disk 1 for a day, trying out every program and it was working normally. One thing I noticed was that iTunes seemed to import as the original tiger 10.4.6 version so I needed to install the update to 7.02 which I had kept in my download folder. I tried to install the OS X update to 10.4.8 but a dialog informed me that I could not do that on this (external) disk. I don't know why, but later on I updated to 10.4.8 overnight using Mac Update.
Step 7. Make sure all your data has been backed up somewhere, and that there is nothing of value on your internal disk. Take a deep breath, and wipe it!! I did this using Disk Utility (from Firewire 1) and took the chance to partition my HD into 32, 18 and 6 gig. I chose GUID partitioning and zeroed the disk. No going back!
Step 8. I booted into Firewire 2 and installed SuperDuper. Then, from Firewire 2, I cloned Firewire 1 onto my internal HD 1 partition of 32 gig. SuperDuper does not call it cloning but rather 'copying all files.' It booted and works fine (as of Jan 10). Then I verified the disk when booted from one of the firewire partitions and all was well. Phew!
I ran sofware Update and it offered to update Java, OS X for Intel, Garageband and Quicktime.
So my node structure is cured and my internal hdd is partitioned without spending a penny and without having to re-install my programs one by one.
Note: There may be a few things to re-install or some prefs to reset but in general this method worked well. I mentioned having ro re-update iTunes.I also had to reset the Quicksilver prefs, and maybe I will yet come across something needing to tweaked again. (QS is a free launcher.) Oh yes, FireFox did not run well so I re-installed it.
I share this in appreciation for the help of Dr Smoke and others who answered my questions and for those whose posts were helpful to read, and for the benefit of others who may find them selves in the same predicament as me. And, oh yes, the trouble was not enough to cause me to go back to that other OS! Louis J
macbook Intel 13" Mac OS X (10.4.8) 2 Ghz model with 1.25 gig RAM

Invalid Node Structure is not a hardware failure, it never was (you may still have a hardware failure, but the Invalid Node error is not indicative of this problem.
Still, Disk utility will certainly fail to fix it, and DiskWarrior will probably fail too.
But don't despair. Try this, and don't give up till you've tried it at least three times.
First, get the name of the partition of the failing volume.   You can get it most easily by finding your disk in Disk Utility, selecting your partition (not the drive) and type cmd-i.    Look for "Disk Identifier" right at the top.
Then, open up Terminal, and type this:
sudo /sbin/fsck_hfs -yprd /dev/disk5s2
substituting your disk identifier for the one already here.   Keep the "/dev/" part.   Enter your password, and wait. It may take a while. I have had this fail several times before finally working so its important to keep trying.   It's faster than a reformat!!!
If the afflicted disk is your startup disk, you will need to do this in recovery mode: restart the computer, hold down option, and wait for the disk options to appear.   Select that, then proceed to Disk Utility and then Terminal as described above.
Good luck, and always keep a backup!
chris watts

IMac (March 2009) - Invalid Node Structure problem

Hi All
I was using my iMac as normal yesterday, when suddenly the system ground to a halt (something I never seen since using OS X). As I had work to do, after about an hour, I restarted, expecting it to be an app misbehaving or something straight forward, but on restart the same thing happened almost straight away.
So, I restarted again, only for the iMac to get stuck on the blue screen which follows the grey 'cog' screen. After looking through these discussions, and some other Mac forums, I booted from the installer disk, tried to run Disk Utility, which found issues and couldn't repair the disk.
I then tried Safe-User mode and fsck, which reported the aforementioned Invalid Node Structure problem. After checking a few more forums, I thought I would try to Erase the disk and reinstall Mac OS. I restored from my Time Machine backup, and finally got it to start, but the system moved at a snail's pace, and wouldn't open any apps or files.
I've tried again with fsck, and also fsck_hfs -r /dev/disk0s2 but all I get is the same error message:
disk0s2: I/O error.
Invalid Node Structure
(4, 38403)
** Volume check failed.
/dev/rdisk0s2 (hfs) EXITED WITH SIGNAL 8
So, does anyone know if there is anything I can do to save the iMac? Or does it need a new HD? It is my primary work computer, so I really need to get it back, and after buying it in the UK, am now in France for 6 weeks, so it's difficult for me to take it to an Apple specialist.
Any help would be greatly appreciated, thanks in advance,
Daniel

As the last user stated, Disk Warrior maybe able to correct it, however if you search the net, you will see there are more than one user with this problem. I had the same problem, however, my machine is out of warranty, It started like you are saying, I RAN disk warrior which corrected the problem long enough to boot the system. In a matter of 10 minutes or so, the system started pausing (apps hung, but in a matter of seconds recovered). I was checking the disk with fsck_hfs and fsck while booted from a USB drive with a maintenance install of 10.5.6. After running fsck the 5th time with different options suggested from the internet, I rebooted with my disk warrior DVD only to find the drive NOT mounted, Drive utility see's it (even can attempt to run disk repair, but it locks up the system when trying this). Disk Warrior doesn't even see the disk to run a directory repair, although in the "check s.m.a.r.t status it sees it as a sata device, and SAYS ITS NORMAL).
Since my iMac was out of warranty, I followed the online instructions to replace the hard drive (not too difficult) and everything is fine now.
The old drive still wont mount, but another utility I bought (data rescue II) has been able to quick scan it and access all the data, even though it wont clear a fsck fsck_hfs or disk warrior, anyways, get it back while you can, IT IS THE hard drive itself, and lots of other iMac users online with the same issue (can you say WHY is my iMac SOOO HOT on the apple in the back (right where the drive is and not sufficient cooling in my opinion, but hey, some people might want to lay their computers face down and fry eggs on the it or something... ))
-SD

Invalid Node Structure on SSD

so i got a vertex 2, 120gb ssd drive a couple of weeks ago, but suddenly my computer crashes hard, my cpu turns out 89c (about 180F) in temp and "quickload D" uses up most of the cpu power. i force quit everything and DMG files just get some error i cant remember now. so i try restart right. but i just get the apple logo and some gray bar at the bottom that goes maybe 10% of the way and then it just shuts off. tried to boot a couple of times but nothing.
so then i boot from the snow leopard disc and run diskutl. and find "Invalid Node Structure" thats not reparable when verifying the disk. so now i have to reinstall. because i haven't come around to getting a system backup yet.
this goes without a hitch and the macbook is just fine now. no invalid node when running verification.
after scouring through OCZs forums i find this to be a reoccurring theme, but mostly on the vertex(1), and that not letting the computer go into hibernation will/might solve this.
so my long winded question is this. anybody else have this happen to them? have you fixed it? and what kind of SSD do you have?

Is your computer still under warranty? If so you might want to bring it to a genius bar. http://www.apple.com/retail/geniusbar/

Invalid node structure, files are visible in single mode

I did something stupid today. First i ran my mac until there was no disk space, resulted in failing booting up. Went into single mode and did a mount command and deleted some big files. And now the disk check is failing and still not able to boot ios. All the files showes up in single mode, but not sure how to proceed. When running fsck it gives invalid node structure error. Marry x-mas :) any ideas?

You might try using Disk Warrior to fix the error, but Disk Utility cannot. Short of DW you will need to repartition and reformat your hard drive unless the Recovery HD partition is still usable. If it is then you can do the following:
Install or Reinstall Lion/Mountain Lion from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Erase the hard drive:
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your startup volume (usually Macintosh HD) from the
      left side list. Click on the Erase tab in the DU main window.
3. Set the format type to Mac OS Extended (Journaled.) Optionally, click on
        the Security button and set the Zero Data option to one-pass. Click on
      the Erase button and wait until the process has completed.
4. Quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion/Mountain Lion and click on the Install button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.

Invalid Node Structure error

Hi All,
I need some information on how I might solve a problem. I ran my Disk Utility earlier today to verify the HD on my MacBook Pro because my computer just seemed a bit off. It froze the other night when I shut it down.
Here is the message I received:
Verifying volume "Macintosh HD"
Checking HFS Plus volume
Checking Extents Overflow file
Checking Catalog file
Invalid node structure
The volume Macintosh HD needs to be repaired
ERROR: The underlying task reported failure on exit
1HFS volume checked
Volume needs repair
I booted the computer from the original OS X Install Disc and tried to repair the hard drive, which didn't work. That's when I started reading the Tiger Forum. I have since discovered that this error cannot be repaired from the Install Disc and probably will require an erase and re-install. However, I did read about a 'fsck' command.
I would like to give this a try, but am not at all comfortable with running commands. Would someone be willing to walk me through this and/or offer any other suggestion for fixing this?
Thanks

Michelle,
Sounds like you are really learning a lot in a hurry. That's good. I can't tell you how long it will be before your system "acts up." I would take this opportunity to backup any really important data to DVD/CDs while you are in the process of getting an external drive and Disk Warrior.
Good question about whether your file system error will be copied to you external drive when you clone with SuperDuper or Carbon Copy Cloner. I don't know exactly but it will certainly be better to have a backup that may be slightly imperfect than to have no backup at all. Of course, after you fix the error on your internal drive with Disk Warrior, then you will reclone your repaired system to your external.
Regards,
Steve M.

Problem when booting - Invalid Node Structure

Hey!
I decided to put my MacBook G4 up to date. So I installed several updates of my software. So far so good. Then I tried to check with Disk Utility wether there were any problems on the file system. I ran "repair Disk Permissions" and some errors where found and corrected. I tried "Verify Disk" and it announced there where some errors namely "Invalid Node Structure". As I couldn't repair the disk as it was the current boot disk I decided to run Disk Utility from a CD. Unfortunately I didn't have my original cd so I asked a friend to use his. He gave me his "MacBook Pro - Mac OS X Install Disc"s (Mac OS X 10.5) and I ran it on my PowerBook G4 (Mac OS X 10.4 installed). It gave the same result like when I ran it from my hard drive. When I tried to repair it, it started and stopped after some seconds (between 20 and 40 seconds) saying it was unable to repair it.
After that the computer does not mount from hard drive (10.4 installed) anymore, only from cd. I tried booting in single user mode and executing /sbin/fsck -fy but I had the same result ("disk0s10: I/O error. Invalid node structure (4, 7698) **Volume check failed.").
I think I can resolve the problem by starting my mac in firewire mode, backing up my data and reinstalling Mac OS X (would a repair from 10.4 Disk Utility work?) but I would be happy if there were any faster / more elegant way to do so as I cant use my install cds for 10.4 right now as I am in an other country for some time.
Any help?

Hi Ja!, and a warm welcome to the forums!
Unfortunately DU & fsck can't fix all that much, your best bet is DiskWarrior, you need the CD though.
http://www.alsoft.com/DiskWarrior/
If DW can't fix it, you might try Data Rescue II...
http://www.prosofteng.com/products/data_rescue.php
(Has a Free Demo to see if it could or not, but you'll need another drive to recover to).
Or FileSalvage...
http://www.subrosasoft.com/OSXSoftware/index.php?%20mainpage=product_info&productsid=1
to recover what you can.
PS. Don't use Leopard Install Disk to work on Tiger Hard disks, it's always messed up my Tiger Disks ehen I did.
Also, not a good idea to even Repair Permissions if there are Disk problems like you have, you don't want to write anything to a disk that has problems, that means even trying to boot off it until you fix it.

Invalid node structure error when verifying hard disk, please help

My 27" Mid 2011 iMac is having hard disk issues. I attempted to repair the disk but received an error that said the disk cannot be repaired and needs to be re-formatted. I have all my files backed up to an external hard drive so I erased and formatted the disk. After reformatting, I ran the verify disk function and got the message saying the HD appears to working properly. I reload OSX Lion and within a day, my computer freezes up and acts as if something is wrong. When I run the verify disk, I get the Invalid Node Structure error multiple times and then the message saying the disk cannot be repaired and I need to reformat the drive. I have completed this process several times and have had no luck. I have looked at a few forums with people who have had somewhat similar problems but am still unsure. I have seen people recommend programs like Disk Warrior to repair issues the hard disk utility cannot but I don't want to spend $100 dollars on this program if my hard disk is damaged and needs to be replaced. Any suggestions? Thank you

Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.
Back up all data on the internal drive(s) before you hand over your computer to anyone. There are ways to back up a computer that isn't fully functional — ask if you need guidance.

Recurring Invalid Node Structure

Hello All,
My Macbook Pro is just 9 months old. It started getting extremely slow and gets hung periodically. Checked the logs. It is showing Disk I/O error. Ran disk utility with the Mac OS installation disk. It shows "Invalid Node Structure".
I then erased all data from hard drive by Zeroing out and reinstalled OS. It starts running fine but only for few days. It gives the same problem again. I tried fcsk utility also from single user mode. it resolves the problem but only for a few days. The problem appears again!!
I thought erasing and reinstalling would resolve the problem unless the hard drive needs to be replaced.Any suggestion would be very helpful.
Thanks,
Sopan

Recurring Invalid Node Structure problems can sometimes be well nigh unrepairable, Sops. They sometimes indicate progressive failure of the drive itself.
I'd be inclined to download the trial copy of "SMART Utility" from http://www.volitans-software.com/smart_utility.php and test the drive with it to make sure this isn't essentially a hardware problem with the drive before accepting the 'SMART" status from Disk Utility . SMART Utility provides much more information in a situation like this, and, though it can sometimes be almost too "critical" , in a situation where you have already tried zeroing without success I'd be inclined to believe it.
With the price of drives down where they are today it probably makes sense to simply get the drive replaced if you run into recurring issues of this kind. In your case you are still under hardware warranty anyway. It is very frustrating to spend hours or days sorting out a drive with "Invalid Node Structure" only to find it recurs a couple of weeks later anyway because it has a hardware defect.
Cheers
Rod

How can you repair "invalid node structure and invalid b-tree node size"

I have a MacBook Pro 17" and the original install disk is Mac OS 10.4. I have an update 10.6 install CD, but I cannot use it to boot up my computer. My computer had been running on 10.6 when the problem occurred.
It seems my harddrive has crashed. It only boots to apple logo and spins. I have reset the pram. Started up in safe mode with shift pressed down and started up on the start up disk, where I did repair disk and got this "invalid node structure invalid b-tree node size". Then it said repair failed to complete. I tried booting again but it still failed. I thought doing a restore might solve the problem. I have a month old backup with time machine which is on a lacie external drive, but when I try to restore using my original 10.4 install disk, I can only choose the lacie hardrive icon (by dragging) and cannot choose the folder in the backups with the latest backup. When I tried to restore, it says my source is not a valid option. Is this because it is a 10.4 startup disk.
Basically I have two questions: Is there a way to fix my problem without doing a restore and if I have to restore, how do I restore my time machine backup? Will I need to do a reinstall with 10.4 and then update to 10.6?
I really hope to find a way to have my computer back to how it was when it started spinning and if not, at least as it was when I did the latest backup 3 weeks ago.
Please help me!!!
Rebecca

You should be able to boot to the Snow Leopard upgrade disc — you had to do so to install the upgrade in the first place. If you can't boot to it now, either the disc is scratched or dirty or your drive's lens is dirty; for the latter problem, a drive cleaning disc is an inexpensive, frequently-used and often successful remedy, available at any store that sells DVDs.
Because you're running Snow Leopard now, you should repair your hard drive directory using the Snow Leopard version of Disk Utility, not the one on your Tiger installer disc. If you aren't able to do so even after trying to clean your drive, you could buy and use DiskWarrior to rebuiild the damaged HD directory. But DW costs nearly $100, and though it would probably do the trick, that's a bunch of money. You'll have to weigh its cost against the value of the new or changed data on your drive that hasn't been backed up in the last three weeks. If you can get along without that data, then erasing your hard drive and restoring from your last backup is the no-cost, immediate (as opposed to waiting for a DW startup disk to arrive in the mail) solution.

Please help! Invalid node structure and invalid record count

My MacBook Pro is about 6.5 years old. I upgraded to Snow Leopard 2 years ago and added RAM at the same time. My first problem ever occurred three days ago when my computer got super sluggish, I restarted and got the gray screen with apple and spinning wheel...no boot up. I ran disk utility from the snow leopard install disk and found "invalid node structure" and "invalid record count". After reading on here what to do...try to repair the disk and so on with no success I went out and bought Disk Warrior. Got home expecting to fix everything and Disc Warrior won't boot...I just get a file with a question mark and the disc is ejected. I tried erasing the hard drive but was only able to use the "don't erase data" option. Then I tried to reinstall Snow Leopard with no luck. Now I am stuck. Any ideas?
One thing to note is I am to the point of not caring about the files on the hard drive, I was a dummy and never backed them up...lesson learned! I just want my computer back without having to spend $1000+ for a new one. Then again I am always willing to do that too as a last resort.
PLEASE HELP!

When you contact Alsoft, make sure you let them know that you are using Snow Leopard (10.6.8).
Try the following in the meantime -
Disconnect all peripherals from your computer.
Boot from your install disc & run Repair Disk from the utility menu. To use the Install Mac OS X disc, insert the disc, and restart your computer while holding down the C key as it starts up.
Select your language.
Once on the desktop, select Utility in the menu bar.
Select Disk Utility.
Select the disk or volume in the list of disks and volumes, and then click First Aid.
Click Repair Disk.
Restart your computer when done.
Repair permissions after you reach the desktop-http://support.apple.com/kb/HT2963 and restart your computer.
Try DiskWarrarior again if it's combatible with the os system.
YOu cannot reformat until you get your issue corrected.

Invalid Node Structure errors keep coming back,

Hi people!
about 2 weeks I upgraded my internal HDD on my Mac Book 13" Unibody to a Western Digital Scorpion Blue 640gb... no big deal doing so. I booted up with the OX S 10.6 DVD and partitioned the drive into two and formatted each. I then installed OS X 10.6, then ran the software update. After every thing was complete I plugged in my USB 1TB drive and used Time Machine to create a backup.
After about a week of normal use I woke up one day to have my Mac Book take nearly 10min to boot, and when it did it was barely moving. I booted with the OS X DVD and ran Disk Utility and in reported Invalid Node Structure and I could not repair it. But the errors were only on the partition with OS X on it.
As I didn't have any files on that partition that I needed I did a Restore from Time Machine Backup that was on my USB drive. And all was good again. However this has happen about 3 times in the last 4-5 days. Each time I restore from the Time Machine backup and all is fine.
I thought I had it pinned down to a particular open source app that I was using but I restored the drive again last night and did not use that app this time... and this morning I am getting signs that something is going astray again (slow boot up times and slow shut down times etc). I am going to boot to the DVD and run Disk Utility again... but I am wondering is this software or can this new HDD be a dude? I never had this problem with the factory 160Gb Fujitsu drive that the Mac Book came with - although I never did partition that drive.
Any thoughts?
Cheers,
Chris

Hi streamworksaudio;
After you do that if this happens again, I would be really suspicious that drive is on the way out. I would be religious about backups and start checking around for a replacement.
Allan

MBP 15" - Hard drive crash - invalid node structure

Hello,
I migrated from a life of pc to mac a month ago and was very pleased with how things worked out. Until two hours ago when the computer freezed (it was showing the rotating ball but no response to any commands). I thought I could force quit some app but it was not responding at all so I waited for 15 minutes before I shut it down via the power button. When I powered it back on there was a catalogue with a question mark blinking on the screen. It seems it cannot find any startup disk.
On the apple support forums it says I might be able to repair the disk via the install CD (Disk utility). I tried it but it says
Verifying volume "Macintosh HD"
Checking Journaled HFS Plus volume.
Checking Extents Overflow file.
Checking Catalog file.
*Invalid node structure*
The volume Macintosh HD needs to be repaired.
Error: Filesystem verify or repair failed.
(something like that. It all takes about 10 sec)
and stops.
On some other forum I found out that fsck -fs could work but nothing really happened there either.
Is there any solution to this?

it seems it's running the fsck command on the DVD drive, which is free of errors. yey for that at least!
"df" gives me
Filesystem 512-blocks Used Available Capacity Mounted on
root_device 15173432 15169920 0 100% /
devfs 208 208 0 100% /dev
fdesc 2 2 0 100% /dev
mount -uw tells me
root_device on / (hfs, local, read-only )
devfs on /dev (devfs, local)
fdesc on /dev (fdesc, union)
that read only cannot be good!
alright so back in disk utility I find that my disk is called disk0s2
running fsck -yf /dev/disk0s2 gives me
BAD SUPER BLOCK: MAGIC NUMBER WRONG
LOOK FOR ALTERNATE SUPERBLOCKS? yes
SEARCH FOR ALTERNATE SUPERBLOCK FAILE: YOU MUST USE THE -b OPTION TO FSCK TO SPECIFY THE LOCATION OF AN ALTERNATE SUPER-BLOCK TO SUPPLY NEEDED INFORMATION; SEE fsck(8).
so I run
fsck -yf -b 32 /dev/disk0s2 since it's in the manual but get
BAD SUPER BLOCK: MAGIC NUMBER WRONG
Am I on the right track here?

Invalid Node structure/ computer running slow?

Similar Messages

Maybe you are looking for