Ipad battery not charging and a lot of other problems after 7.1.2

I don't believe that i am saying this the update 7.1.2 is a bloody mess
The battery does not charge and It only charges when the ipad is turned off! WHAT!?
The internet is really gone for me.I cant login to facebook and instagram always some error.
it keeps saying some server problem for the last week.
Please Help I saw some other discussion related to this too
Please Apple maybe you just lost a customer

Is it a third party charger or the one that came with the purchase? Does your iPad give you any message on the screen? if not, you can get on with a live support agent via live chat: https://getsupport.apple.com/Issues.action

Similar Messages

  • My Ipad will not charge and Ihave booted it and still no chargeing tryed computer and wall plug

    my Ipad will not charge and Ihave booted it and still no chargeing tryed computer and wall plug

    The best way to charge an iPad is to use the charger that came with it connected to a known good wall outlet. The following might be the problem.
    No power in the outlet.
    Bad charger unit. Try a different charger.
    Bad cable. Try a know good cable.
    Dirt in the connector on the iPad. Check and clean.
    A fault in the charging software. Reset your device. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider should one appear until the Apple logo appears. Let go of the buttons and let the device restart. See if that fixes your problem.
    A hardware failure. Make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support.

  • My iPad will not charge and will not switch on, blank screen.....

    IPad dead
    My iPad will not charge and will not switch on, blank screen.....

    Have you tried a soft-reset to see if that gets the iPad to turn on and/or to charge ? Press and hold both the sleep and home buttons for about 10 to 15 seconds, after which the Apple logo will hopefully appear - you won't lose any content, it's the iPad equivalent of a reboot.

  • My iPad will not charge and every time I charge it. It comes up with the iTunes icon and I will not charge, it is not a new I pad and the same charger I use for the I pad I use for my I phone and it will charge. What is wrong?

    My iPad will not charge and every time I charge it. It comes up with the iTunes icon and I will not charge, it is not a new I pad and the same charger I use for the I pad I use for my I phone and it will charge. What is wrong?

    What exactlyare you seeing on the iPad's screen ? If it's the iTunes icon and a cable then that means that it's gone into recovery mode - you will need to connect it to your computer's iTunes and you should be able to use that to reset it back to factory defaults and you can then restore/resync your content to it.

  • My ipad is not charging and cannot on

    my ipad is not charging and cannot on

    I am having the same issue with my iPad Air since upgrading to iOS 8.3. I need to close all open apps and power off the device with the plug attached, it then reboots and is receiving a charge. This did not happen prior to the update and it happens whatever charger/cord combination I connect.

  • Personal hotspot missing and music volume not working and lots of other problem after updated 4s to ios8 ? Apple disappointed this time badly.

    Personal hotspot missing and music volume not working and lots of other problem after updated 4s to ios8 ? Apple disappointed this time badly.

    GO to Setting > Cellar Data > VPN Settings > Add any user and password under Personal Hotspot, then you will see it's activated again as usual

  • Macbook pro shows battery not charging and the power cord has a dim green light

    hi,
      my mac book pro the battery is shown as not charging and the power cord has a dim green light ,  but the battery condition is seen as normal in system profiler , below are the details
    Battery Information:
      Model Information:
      Serial Number:  9G00102XU8VPC
      Manufacturer:  DP
      Device name:  bq20z451
      Pack Lot Code:  0000
      PCB Lot Code:  0000
      Firmware Version:  0003
      Hardware Revision:  0002
      Cell Revision:  0100
      Charge Information:
      Charge remaining (mAh):            1365
      Fully charged:            No
      Charging:            No
      Full charge capacity (mAh):            4409
      Health Information:
      Cycle count:   482
      Condition:   Normal
      Battery Installed:       Yes
      Amperage (mA):       112
      Voltage (mV):       11421
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes):       15
      Disk Sleep Timer (Minutes):       10
      Display Sleep Timer (Minutes):       5
      Wake On AC Change:       No
      Wake On Clamshell Open:       Yes
      Wake On LAN:       Yes
      Current Power Source:       Yes
      Display Sleep Uses Dim:       Yes
      Battery Power:
      System Sleep Timer (Minutes):       10
      Disk Sleep Timer (Minutes):       10
      Display Sleep Timer (Minutes):       2
      Wake On AC Change:       No
      Wake On Clamshell Open:       Yes
      Display Sleep Uses Dim:       Yes
      Reduce Brightness:       Yes
    Hardware Configuration:
      UPS Installed:       No
    AC Charger Information:
      Connected:     Yes
      ID:     0x0000
      Wattage (W):     0
      Revision:     0x0000
      Family:     0x0000
      Serial Number:     0x00000000
      Charging:     No
    my system sofware overview is as follows
    System Version:  Mac OS X 10.6.8 (10K549)
      Kernel Version:  Darwin 10.8.0
      Boot Volume:  Macintosh HD
      Boot Mode:  Normal
    can you please tell me whats wrong with my mbp and how do i resolve it

    First check the connections on the power adapter and the MBP.  Make certain that they are clean and see if the spring loaded connectors on the power adapter are not stuck.
    Try a SMC reset:
    http://support.apple.com/kb/ht3964
    If available, try another power adapter.
    If no success, bring the MBP and the power adapter to an Apple store genius bar for a free evaluation.
    Ciao.

  • My iPad is not charging and it gets very hot

    My iPad isn't charging and it's get really hot.. What is wrong with it?

    Hello there simisammy,
    If the iPad is not recognized in iTunes then I recommend this article iOS: Device not recognized in iTunes for Windows found here http://support.apple.com/kb/TS1538.
    This is a basic over view of the troubleshooting involved with it.
    To begin troubleshooting this issue on your iOS device, first follow the steps in the appropriate troubleshooting assistant below:
    iPhone Troubleshooting Assistant
    iPod touch Troubleshooting Assistant
    iPad Troubleshooting Assistant
    If the issue persists after following the troubleshooting assistant, continue with the steps below, testing to see if the issue is resolved after each section.
    Collapse All Sections | Expand All Sections
    1. Update iTunes
    2. Check the USB cable
    3. Verify that Apple Mobile Device Support is installed
    4. Restart the Apple Mobile Device Service
    5. Verify that the Apple Mobile Device USB Driver is installed
    6. Check for third-party software conflicts
    When that is finished I would recommend this article
    iOS: Unable to update or restore
    http://support.apple.com/kb/ht1808
    Regards,
    Sterling

  • Battery not charging and MBP not waking up from sleep

    I've got both of these issues happening. Sounds like I just have to wait it out on the sleep issue until a point at which Apple will issue a fix. The battery not charging is becoming especially frustrating though. I've had the computer for about a month and it just started a few days ago. I've checked the battery to see if it qualifies for replacement and it has the correct model number but the s/n has a different last for digits. I've unplugged/removed battery/held down the power button and no change, the battery still does not charge. Seeing as the MBP will run with the power cable inserted and the battery removed, I'm assuming that the cable's ok, the light has rarely come on at all lately -- no green or amber. Any advice here? I'm getting pretty frustrated with this thing.

    I met the same issue, the difference is while i touch the track pad or move mouse or hit keyboard, the screen responds rapidly and then back to black. tap the keyboard, it beeps... I can do nothing except "command+control+power" to restart or long press power to power off it.
    I found it only happens after I installed 10.8.2, it works well before 10.8.2 update.
    any help please?

  • My ipad is not charging and the button is not working

    my ipd2 is not syncing and is not charging and last thing the button is not working i have had it only two weeks!!

    Hello ipadisbroken,
    Thank you for using Apple Support Communities.
    For more information, take a look at:
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/ts3281
    Have a nice day,
    Mario

  • "Battery Not Charging"... Cold weather problem

    I think I have figured out that that charging device does not work when the computer is cold.
    This is the 2nd time it has happened. I reset PRAM and PMU with no change. Then later it spontaneously fixed itself when the sun started hitting the van. Thinking possibly when the computer is cold it happens, since it was 17º this morning and the computer was asleep all night. I had run the battery that evening depleting it totally. However, the night before it was -11º and the problem did not happen, possibly because I had left it running all night with no disk spindown.
    Also, looking backwards at Oct 29 of the first occurrence, yes we did have a cold spell and a snowstorm, I remember now it hit about 17º.
    So it seems like this is a problem when the charging device is cold (actually my cellphone does the same thing). The solution would be to keep the disk spinning full time while it is below about 25º. Or maybe even put some insulation over the computer.
    I had a 1.6 PowerBook earlier that never showed this problem. It charged normally down to -5º. So perhaps this is an Intel oddity.
    I realize I am running the MacBook at 63º below tech specs, so please refrain...

    I think I have the same problem. Macbook Pro indicates shortly it doesn't charge, then turns to charging. But the last time it stuck to 'battery not charging'. Then I played for about fifteen minutes, warming up the video card (and it does get warm) and now it charges again.
    It remains a strange problem and I will see the MacStore about it.

  • IPad battery not charging

    My ipad is about 9 months old, used daily, and this evening developed a 'not charging' message in the top corner (next to the battery icon) with an intermittent message flashing on the screen saying that 'charging is not supported with this accessory'.  I do regular battery calibration (every 6 weeks or so) and have had no recharging problems. 
    Is this a visit to an Apple store or something fixed at home?

    I recently started experiencing the exact same issue. For the past year I have been using my ipad the most in my office. I have it set up on my desk with the usb cable and an older wall outlet cube from one of my first iphones and it would be left charging all day. Everything was working perfectly until a few weeks ago. When I would plug the usb in, it would initially give the the charging indicator, then it would display the small power plug graphic as if it was fully charged, then it would switch rapidly back and forth between 'fully charged' and 'charging', and would finally end up saying 'not charging'. Shortly after that, the message would appear that 'charging is not supported with this accessory' even though these are all Apple parts. I tried several different cables and had the same results. Finally, I decided to switch out the charging outlet cube itself, and that did the trick. Now it charges exactly like it is supposed to with no issues. I hope this works for you because it sounds like we are dealing with the exact same thing. I was also concerned that I would have to take it in for repair or replacement, but fortunately, one of the simplest solutions worked. Good Luck!

  • New battery not charging and no power supply reported

    The battery for my G4 17inch powerbook had expired and a new one was needed. A brand new battery has been purchased and inserted into the machine. With the old battery the charger would go green then quickly amber before going off. With the new battery the light never comes on and in the battery info in the operating system it is listed as a new battery with 1 charge but the power supply section is not listing the power as connected. However with no batterys inserted the power supply will power and run the machine.
    Can anyone offer any advise of something I could try or is it likely to be a dead laptop / charging circuit?
    Thanks

    There's 4 components in the charging circuit: power adapter, DC-in card, battery, and logic board. If you can run on power without the battery, and does not run when you insert a battery, that suggests that the DC-in board may be OK. So ... power adapter works, assume DC-in card works, new battery assume it works ... if you accept those assumptions, then you have a logic board issue.

  • Battery Not Charging and stuck at 0%

    Hi,
    I have a MacBook Pro on which the battery suddenly appears to have died. It was working fine, I switched it off when I went away for the weekend and on Monday morning it's behaving as if a battery wasn't plugged in. As soon as I unplug the power the laptop turns off.
    Battery Information in System Profiler says;
    Charge Information:
    Charge remaining (mAh): 0
    Fully charged: Yes
    Charging: No
    Full charge capacity (mAh): 0
    Health Information:
    Cycle count: 169
    Condition: Check battery
    Battery Installed: Yes
    Amperage (mA): 0
    Voltage (mV): 12511
    What's the opinion of this board - just a dead battery? The laptop is almost exactly 2 years old, what are the chances of Apple kindly giving me a replacement?
    Thanks in advance.
    Paul

    "is there anyway i can auto-update battery firmware, whenever it is released? "
    Check Software Update. Or go to:
    HD/System/Library/SystemConfiguration & look for a file called batteryupdater.bundle. Select Get Info for the file.
    If its version number is 1.2 or 1.3 you should be fine If not, or if you cannot locate a batteryupdater.bundle file (by using Spotlight, searching manually or using a 3rd party search feature) then download an update from Apple's website & install it. If installing has no effect, you probably need a new battery.
    Make sure you calibrate your battery every month or 2. You will need to read your user manual to determine the correct amount of times for _*your model*_ MBP.
    Make sure your MBP is getting proper ventilation. According to the user manual it states in part:
    +"Do not operate your MacBook Pro on a pillow or other soft material, as the material can block the airflow vents. Never place anything over the keyboard when operating your MacBook Pro. Never push objects into the ventilation openings."+
    See User Tip: Apple notebook batteries – maintenance and troubleshooting
    ========================
    It would help if you would complete My Settings which is located in the column on the right under your name and filling in the information asked for. Thank you.

  • Battery not charging and makes weird noise when power cord plugged in

    I have an issue that a few people have mentioned here, my PowerBook won't recognize when a power adapter is plugged in. I've bought two power adapters recently (that I probably DON'T need now) so I know it's not a bad adapter.
    For a few months it has been switching back and forth between wall and battery power but usually only when I was really working the machine either video or photo editing but it has been getting worse.
    The thing that is happening to me that I haven't seen mention is my computer makes a fast ticking noise when it is plugged in. Once I unplug it, it stops. And while it was off and plugged in the computer was making a weird whistling noise.
    Is this a bad DC/sound card issue and does Apple still do these types of repairs at a Genius Bar or am I on my own?
    Thanks for any and all help.

    I know exactly what you mean. My 17 inch PB has been quite "noisy" since I received it, but i wrote it off (I was too ecstatic that work bought me a PB). Just recently the sound has been getting louder. I'm starting to think the sound was actually electrical interference that was being picked up by the speakers. Actually today I was in a meeting (speakers still working) and the squeeling sound was getting louder (almost embarrasing loud considering I'm the apple diehard in a pc dominated office). I decided to reset my computer (not something I do often)It seemed to subside for a bit.
    Well today, it looks as though my speakers have died on me. I'm not getting any sounds out of them. I'm not a newb when it comes to macs (been using macs since os9, about '99) so I've tried everything I can think of to get the speakers to come back. I believe I'm experiencing a hardware failure (reset many times, check all settings).
    Hmph.....Pretty frustrating. No iTunes during work makes me sad. I'll have to check and see if my external sound still works tomorrow.
    -Kevin
    Powerbook G4 17", Cube, PowerMac G4, Imac G5   Mac OS X (10.4.7)  

Maybe you are looking for

  • Runtime Errors CONNE_IMPORT_CONVERSION_ERROR

    Error in IMPORT statement: Change of length on conversion. Hi this is an error i had when creating a source system for a client. Runtime Errors CONNE_IMPORT_CONVERSION_ERROR Occurred on 21.02.2005 at 14:08:20 The error probably occurred when installi

  • Aperture 3 and Mobile User Accounts: Don't even think about it

    Hi all. This is more a warning to other with a similar setup than anything else. I use both a desktop mac and a portable. As so, and since I have a Mac Mini Server, my user is what Apple calls a "Mobile User". Basically what it does is this: it allow

  • SQL Loader Control file help!!!

    Hi All, I was in the process of writing a control file for sql loader for an activity i am performing and would appreciate inputs from you all. I have a table patient containing 44 columns, i have a column 'SEC_LANG_NAME' in which i have to insert da

  • Reverse F.05 Postings

    Hi, We have passed the foreign exchange revaluation as on 31.03.2008 in Tr. Code F.05 which posted for  some GR IR Accounts.  We require to do only ONE GL AC.. Hence please advice me  how to reverse entrie of remaining gl a/c. Regards RRR Edited by:

  • P2035 takes 2 minutes to print each page

    2035 printer and a Windows 7 computer.  First page prints normally.  Each Additional page takes 2 minutes to print. I have unplugged the printer and downloaded every available driver update.  The toner is a new HP unit.  Any ideas?