IPad only shows a grey screen.

Yesterday evening my iPad turned off by itself. Now when it start it only shows a grey screen. A reset causes the Apple logo to appear momentarily I cannot get the iPad into recovery mode.
The battery is fully charded, was plugged in over night.
Originial iPad running 5.1.1
Only chnage yesterday was I updated one App.
Tried standard reset using home and power button.
Interesting the Apple Logo appears to have a yello mark on it, but that may just be an illusion.
ITunes seems to see the device but says it need to be unlocked. " iTunes cannot backup "iPad "iPad name" because it is locked with a passcode."
Thanks in advance.

Thanks for your reply.
I tried that. Nothing appears on the iPad screen although the backlight come on but in iTunes I get the same error. " iTunes cannot backup "iPad "iPad name" because it is locked with a passcode.

Similar Messages

  • TS2570 i need help with my computer, it only shows a grey screen

    i need help!!!!

    Give this a try if you have an Apple logo and spinning gear displayed on the screen:
    Reinstalling Lion/Mountain Lion Without Erasing the Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

  • My New ipad3, when i click onthe camera app, the front camera works but the other camera only shows a black screen ! Is there something wrong with my iPad ?

    My New ipad3, when i click onthe camera app, the front camera works but the other camera only shows a black screen ! Is there something wrong with my iPad ?

    Try a Reset [Hold the Home and Sleep/Wake buttons down together for 10 seconds or so (until the Apple logo appears) and then release. When the screen goes blank power On again in the normal way.] It is absolutely/appsolutely safe!

  • The video app on my iPad now only shows a black screen. Used to work fine then crashed in the middle of a short video.

    The video app on my iPad now only shows a black screen. Used to work fine then crashed in the middle of a short video.  When I open the app the screen is just blank. As it is a default app I can't delete and reinstall. Anybody else experience this?

    Try searching for the name of one of your videos on the iPad's spotlight search screen - swipe your first homescreen to the right, type in it's name, and if it finds it tap on it to see if it plays.
    If that doesn't work then try closing the Videos app via the taskbar : from the home screen (i.e. not with the Videos app 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Videos app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
    A third option if the two above don't work is a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

  • My ipad is freez...it only show a home screen. but i can turn off my ipad but not shut down...and i went to my computer and i go to itune. i try to restart my ipad but it say turn off your.find my iphone..but i cant my ipad is freezing.can help me plz.

    my ipad is freez...it only show a fome screen. but i can turn off my ipad but not shut down...and i went to my computer and i go to itune. i try to restart my ipad but it say turn off your.find my iphone..but i cant my ipad is freezing.can help me plz.

    Have you tried to reset it? Hold down the sleep and home keys for about 20 seconds and see if you can get it to reboot.

  • My ipad is freez...it only show a fome screen. but i can turn off my ipad but not shut down...and i went to my computer and i go to itune. i try to restart my ipad but it say turn off your.find my iphone..but i cant my ipad is freezing.can help me plz.

    my ipad is freez...it only show a fome screen. but i can turn off my ipad but not shut down...and i went to my computer and i go to itune. i try to restart my ipad but it say turn off your.find my iphone..but i cant my ipad is freezing.can help me plz.plz help me.................thx u

    Option 1
    Try force iPad into Recovery Mode. Follow step 1 to 6 very closely.
    http://support.apple.com/kb/HT1808
    Note: You need to be patient and repeat the above many times to recover your iPad

  • IPad freeze up and appear to be dead and only show a black screen

    My iPad2 freeze up and appear to be dead and only show a black screen, why is it so?

    Have you tried a reset ? Press and hold both the sleep and home buttons for about 10 to 15 seconds, after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot. It happens occasionally judging by the posts on here, but only once so far to me.

  • I am having a minor problem to my iphone. It crashed and when i tried to restore it, its only showing the home screen without any icons whatsoever. How can i fix this issue?

    my iphone crashed and isn't showing any icons or apps. Its only showing the home screen. How can I fix or resolve it.

    Restore your iphone
    If you can't update or restore your iPhone, iPad, or iPod touch

  • My MacBook Pro shows a grey screen  at start-up how do I fix this problem?

    My MacBook Pro shows a grey screen when I try to login and won't go onto my homepage. Why has this happened and how do I fix it?

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
    There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
    a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
    b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
    c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a startup failure can be resolved by resetting the NVRAM.
    Step 4
    If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
    Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
    If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
    If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
    Step 9
    If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.  
    Step 10
    Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 11
    Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
    Step 12
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 13
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • IPad only shows 11 pages of Apps!! Help!!

    I have over 350 apps (half of those from iphone/ipod touch). After successfully syncing them, my iPad only shows 11 pages of apps. There is supposed to be 17. Is anyone else experiencing this with such a capacity of apps

    "You can create up to 11 screens." Page 11 of the iPad User Guide
    If you have a lot of applications, you can use Spotlight Search to locate and open them.

  • My iPad Mini iOS7 is showing only Apple Logo which happened during software update. I tried to restore using iTunes but it asking me to response from iPad. But my ipad only shows apple logo. How can i response? How to solve this problem?

    My iPad Mini iOS7 is showing only Apple Logo which happened during software update. I tried to restore using iTunes but it asking me to response from iPad. But my ipad only shows apple logo. How can i response? How to solve this problem?

    FORCE IPAD INTO RECOVERY MODE
    1. Turn off iPad
    2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
    3. Plug USB cable into computer's USB port
    4. Hold Home button down and plug the other end of cable into docking port.
    DO NOT RELEASE BUTTON until you see picture of iTunes and plug
    5. Release Home button.
    ON COMPUTER
    6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
    7. Select "Restore iPad"...
    Note:
    1. Data will be lost if you do not have backup
    2. You must follow step 1 to step 4 VERY CLOSELY.
    3. Repeat the process if necessary.

  • I don't know what's wrong with my 3GS. It only shows the black screen with white apple. Turning it on then off doesn't help.

    I don't know what's wrong with my 3GS. It only shows the black screen with white apple. Home button and turning the phone off then on doesn't seem to do anything.

    Thanks Lucas,
    I've tried doing that with no results. Same screen keeps showing. Maybe it'd be more helpful if I told you a bit more info.  My phone was randomly playing music, and the voice control would also suddenly start without me touching the phone.  Then I let the battery die and started to recharge when on the screen it indicated to plug into my computer/iTunes, I tried to restore but was getting an error message (can't remember what it said now). Battery died and now my current issue of the black screen with white apple.  I'd love to be able to restore my phone but now its not showing as a device on my iTunes. HELP! Any other suggestions?

  • Skype Video Calling only showing a black screen

    Hi,
    When I make a viseo call, my computer only shows a black screen. The other person can see me just fine, but my video show just a blank screen. It's definitely a problem on my computer as it has happened with a couple of different people. 
    Both screens that should be showing video (the one that shows them, and the one that shows me) are showing black.
    I've had a look around but haven't been able to find any solutions. 
    Any help would be much appreciated.
    thanks
    Solved!
    Go to Solution.

    Most likely the issue is with your display adapter.
    Please,  run the DirectX diagnostics tool.
    Go to Windows Start and in the Run box type dxdiag.exe and press the OK button. This will start the DirectX diagnostics program. Run this diagnostics and save the results to a file. Please, attach this file to your post.
    Be aware that you will have to zip this file before attaching it here.

  • My ipod only shows a black screen and an apple logo

    My ipod only shows a black screen and an apple logo. It wont connect to iTunes, and charging doen't work. HELP PLEASE!

    Try a reset. Hold the home and power buttons at the same time until the screen goes dark for a moment, then the Apple boot logo should reappear. If it doesn't work, it's broken, take it to the Apple store or another authorized repair service.

  • MY COMPUTER ONLY SHOWS A BLACK SCREEN, WITH ONLY THE POP UP SHOWING .....VIEW AND TRACK YOUR DOWNLOADS

    MY COMPUTER ONLY SHOWS A BLACK SCREEN, WITH ONLY THE POP UP SHOWING .....VIEW AND TRACK YOUR DOWNLOADS

    Hi,
    First plaese unplug any external device (except the mouse and keyboard), then hold on the power button, perform a cold reboot, what is the result?
    If doesn't work, please press F8 (or other button, depend on your PC model) boot your compute into recovery console.
    You can restore your system to a previous point or perform a startup repair, please refer to the following link:
    What to do if Windows won't start correctly
    http://windows.microsoft.com/en-in/windows-vista/what-to-do-if-windows-wont-start-correctly
    Yolanda Zhu
    TechNet Community Support

Maybe you are looking for