Iphone 6 plust update to 8.1 failed with unknown error (6)
Trying to update my iphone 6 plus to ios 8.1 using windows laptop running windows 7. It failed with giving message update failed with unknown error (6).
Exact error is:
The iPhone "iPhone" could not be restored. An unknown error occured (6).
After this whenever I connect iphone to my laptop itunes shows serial number as n/a and it keeps on asking me to restore but always fails.
Any help in resolving the issue (either completing the update or restoring to factory defaults) is highly appreciates.
Thanks.
Checked the update logs and see the following at the end:
[11:07:48.0460] requested restore behavior: Erase
[11:07:48.0461] device did not return saved USB log
[11:07:48.0461] device did not return saved panic log
[11:07:48.0462] previous restore failed with exit status 0x100
[11:07:48.0463] connected to service com.apple.mobile.restored
[11:07:48.0464] using protocol version 13
[11:07:48.0464] unable to open device_map.txt: No such file or directory
[11:07:48.0465] board config = n56ap
[11:07:48.0466] no value returned for BootArgs
[11:07:48.0467] _copyDeviceProperty() failed for restore bootargs
[11:07:48.0468] no value returned for MarketingPartNumber
[11:07:48.0469] _copyDeviceProperty() failed for mpn
[11:07:48.0469] requested restore behavior: Erase
[11:07:48.0470] value query for 'HardwareModel' returned 'N56AP'
[11:07:48.0471] Established proxy for device ID 4
[11:07:48.0522] <Restore Device 06B9BF48>: operation 35 progress -1
[11:07:48.0525] requested restore behavior: Erase
[11:07:50.0998] <Restore Device 06B9BF48>: operation 28 progress -1
[11:07:59.0151] no override trust object found
[11:08:20.0357] device returned CFError with code 6
[11:08:20.0361] dumping CFError returned by restored:
[11:08:20.0364] CFError domainXXXXXXXXXXXXXXXXXXXin code:6 description:Fatal FDR Error returned from RestoredFDRCreate()
[11:08:20.0368] Sending acknowledgement that final status was received
[11:08:20.0759] Restore completed, status:6
[11:08:20.0759] Failure Description:
[11:08:20.0759] Depth:0 Error:AMRestorePerformRestoreModeRestoreWithError failed with error: 6
[11:08:20.0759] Depth:1 Error:The operation couldn’t be completed. (AMRestoreErrorDomain error 6 - Failed to handle message type StatusMsg)
[11:08:20.0759] Depth:2 Error:The operation couldn’t be completed. (AMRestoreErrorDomain error 6 - Fatal FDR Error returned from RestoredFDRCreate())
Hi sailesh.chopra,
Thanks for the question. After reviewing your post, it sounds like you are not able to update because of an error 6. I would recommend that you read this article, it may be able to help you isolate or resolve the issue.
Resolve iOS update and restore errors - Apple Support
Check your security software
Related errors: 2, 4, 6, 9, 1000, 1611, 9006. Sometimes security software can prevent your device from communicating with either the Apple update server or with your device.
Check your security software and settings to make sure that they aren't preventing a connection to the Apple servers.
Thanks for using Apple Support Communities.
Have a nice day,
Mario
Similar Messages
-
i have updated my itunes but when im restoring my iphone 5 phone it keeps coming up with 'unknown error occurred (3) please help as i cannot even turn my phone on now
Hello there, BundyA.
Error 3 is usually associated to security software settings. The following Knowledge Base article provides some great information and links for troubleshooting the issue:
Resolve specific iTunes update and restore errors
http://support.apple.com/kb/ts3694
This section should prove useful:
Configure your security software
Check your security software and settings, which can block ports and prevent connection to Apple servers during update and restore.
Common errors: 2, 4, 6, 9, 1000, 1611, 9006, 9807, 9844. Sometimes as a result of this issue, a device might stop responding during the restore process.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro. -
CRM 2015 Update 0.1 Install Fails with SQL Error
Hi, anyone managed to install CRM 2015 Update 0.1?
The software installed fine but the DB updates fail with a SQL error. Just want to know if this is just my issue or if MS have a bug in the update. This is the SQL error:
System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.Data.SqlClient.SqlException: The current transaction cannot be committed and cannot support operations that write to the log file. Roll
back the transaction.
Uncommittable transaction is detected at the end of the batch. The transaction is rolled back.
All of the ORGs fail with this error, even when I try to apply the DB update via Deployment manager. I've had to back out the rollup.The issue appears when the update process creates the index cndx_BusinessDataLocalizedLabel. This is a known cause which is under investigation internally. Currently it seems to plan to release in CRM 2015 SP1
-
Updated my iphone 4, updated and then came up with an error
Hi
I updated my iphone 4, as it finished updating it came up that there had been an error and now iphone wont do anything except come up with the picture of a usb cable and a cdwith itunes on it. My phone is connected to laptop but itunes wont load up unless i load it? Any ideas will be greatfully received.Connect to iTunes on your regular PC/MAC
-
Sync failing with unknown error - previously worked
Over the past month, my desktop Firefox has started displaying the dreaded “Sync encountered an error while syncing: Unknown error.” message. I've tried disconnecting and reconnecting the browser, but it still does it.
Unlike other reporters, I'm not seeing any obvious issues that might pertain to my profile (e.g., corrupted places.sqlite). All seems innocuous until it ends with things along the lines of:
<some seemingly OK stuff snipped>
1406223828207 Sync.Service DEBUG Weave Version: 1.33.0 Local Storage: 5 Remote Storage: 5
1406223828207 Sync.Service INFO Sync key is up-to-date: no need to upgrade.
1406223828207 Sync.Service DEBUG Fetching and verifying -- or generating -- symmetric keys.
1406223828207 Sync.BrowserIDManager DEBUG _ensureValidToken already has one
1406223828410 Sync.Resource DEBUG mesg: GET success 200 https://sync-27-us-west-2.sync.services.mozilla.com/1.5/1006668/info/collections
1406223828410 Sync.Resource DEBUG GET success 200 https://sync-27-us-west-2.sync.services.mozilla.com/1.5/1006668/info/collections
1406223828411 Sync.Service INFO Testing info/collections: {"bookmarks":1406143818.46,"meta":1405163266.19,"clients":1406138521.09,"crypto":1399970739.18,"greasemonkey":1405163174.88}
1406223828412 Sync.CollectionKeyManager INFO Testing for updateNeeded. Last modified: 0
1406223828412 Sync.Service INFO collection keys reports that a key update is needed.
1406223828413 Sync.BrowserIDManager DEBUG _ensureValidToken already has one
1406223858621 Sync.Resource DEBUG mesg: GET fail 503 https://sync-27-us-west-2.sync.services.mozilla.com/1.5/1006668/storage/crypto/keys
1406223858621 Sync.Resource DEBUG GET fail 503 https://sync-27-us-west-2.sync.services.mozilla.com/1.5/1006668/storage/crypto/keys
1406223858622 Sync.Status DEBUG Status.login: error.login.failed => error.login.reason.server
1406223858622 Sync.Status DEBUG Status.service: success.status_ok => error.login.failed
1406223858622 Sync.ErrorHandler DEBUG Got Retry-After: 1884
1406223858622 Sync.Status DEBUG Status.login: error.login.reason.server => error.sync.reason.serverMaintenance
1406223858622 Sync.Status DEBUG Status.service: error.login.failed => error.login.failed
1406223858623 Sync.SyncScheduler DEBUG Got backoff notification: 1884000ms
1406223858623 Sync.SyncScheduler DEBUG Fuzzed minimum next sync: 1406225742623
1406223858623 Sync.Service WARN Got status 503 fetching crypto keys.
1406223858624 Sync.Service WARN Failed to fetch symmetric keys. Failing remote setup.
1406223858624 Sync.Service WARN Remote setup failed.
1406223858626 Sync.SyncScheduler DEBUG Clearing sync triggers and the global score.
1406223858627 Sync.SyncScheduler DEBUG Next sync in 2214594.8767703027 ms.
That 503 error is very common. Whilst fiddling, I think I saw a 502, but wouldn't swear to it.
With the logOnSuccess option enabled, I get something which, helpfully, appears to be completely different!
1406224011465 Sync.Service DEBUG Weave Version: 1.33.0 Local Storage: 5 Remote Storage: 5
1406224011465 Sync.Service INFO Sync key is up-to-date: no need to upgrade.
1406224011465 Sync.Service DEBUG Fetching and verifying -- or generating -- symmetric keys.
1406224011466 Sync.BrowserIDManager DEBUG _ensureValidToken already has one
1406224011678 Sync.Resource DEBUG mesg: GET success 200 https://sync-27-us-west-2.sync.services.mozilla.com/1.5/1006668/info/collections
1406224011678 Sync.Resource DEBUG GET success 200 https://sync-27-us-west-2.sync.services.mozilla.com/1.5/1006668/info/collections
1406224011679 Sync.Service INFO Testing info/collections: {"bookmarks":1406143818.46,"meta":1405163266.19,"clients":1406138521.09,"crypto":1399970739.18,"greasemonkey":1405163174.88}
1406224011679 Sync.CollectionKeyManager INFO Testing for updateNeeded. Last modified: 0
1406224011680 Sync.Service INFO collection keys reports that a key update is needed.
1406224011681 Sync.BrowserIDManager DEBUG _ensureValidToken already has one
1406224130781 Sync.Status DEBUG Status.service: success.status_ok => success.status_ok
1406224130781 Sync.Status DEBUG Status.service: success.status_ok => success.status_ok
1406224133509 Sync.Status DEBUG Status.service: success.status_ok => success.status_ok
1406224133509 Sync.Status DEBUG Status.service: success.status_ok => success.status_ok
1406224135853 Sync.Status DEBUG Status.service: success.status_ok => success.status_ok
1406224135853 Sync.Status DEBUG Status.service: success.status_ok => success.status_ok
1406224136820 Sync.Status DEBUG Status.service: success.status_ok => success.status_ok
1406224136820 Sync.Status DEBUG Status.service: success.status_ok => success.status_ok
1406224189681 Sync.Status DEBUG Status.service: success.status_ok => success.status_ok
1406224189682 Sync.Status DEBUG Status.service: success.status_ok => success.status_ok
1406224311683 Sync.Service WARN Got exception "Error: Aborting due to channel inactivity." fetching cryptoKeys.
1406224311683 Sync.Status DEBUG Status.login: error.sync.reason.serverMaintenance => error.login.failed
1406224311683 Sync.Status DEBUG Status.service: success.status_ok => error.login.failed
1406224311684 Sync.Service WARN Failed to fetch symmetric keys. Failing remote setup.
1406224311684 Sync.Service WARN Remote setup failed.
1406224311686 Sync.SyncScheduler DEBUG Clearing sync triggers and the global score.
1406224311687 Sync.SyncScheduler DEBUG Next sync in 2214594.8767703027 ms.
It all looks comms related to me, but my broadband isn't playing up.Hello,
Thanks for letting us know about your problem. It seems that there is some problem in your profile. Creating a new profile may fix your problem. Create a new profile and sync with your Firefox Account.
For Creating a profile, Please do following:
If Firefox is already included in your Linux distribution or if you have installed Firefox with the package manager of your Linux distribution:
# Close your Firefox.
# In '''Terminal''' run: <br/> <code>firefox -P</code>
# To start the Create Profile Wizard, click '''Create Profile...''' Button in the Profile Manager.
# Click {button Next} and enter the name of the profile. Use a profile name that is descriptive, such as your personal name. This name is not exposed on the Internet.
# To create the new profile, click '''Finish'''
For more instruction regarding creating a new profile, please see this article. [[Use the Profile Manager to create and remove Firefox profiles]] -
Queued files randomly failing with "Unknown error"
This making no sense. Any file I queue singularly into ME from premiere will export fine. If I queue up a bunch and let it go on its own, the files randomly fail. The log says unknown error.
I'm on win 7, I have 16 GB of RAM, I am using Mercury acceleration, ppreHeadless.exe is using 2.1 GB or RAM, resource monitor is telling em I have 5 GB of RAM not in use that is available and CPU usage is maxed.
ANY ideas what could be the issue?
EDIT:
Seems ot be happening randomly with singular vids as well. All possible updates are installed. It gets right to rendering the last frame of the file and then hangs and then the sheep yells at me.
Edit 2: Exporting them right of Premiere works just fine.Hello,
Thanks for letting us know about your problem. It seems that there is some problem in your profile. Creating a new profile may fix your problem. Create a new profile and sync with your Firefox Account.
For Creating a profile, Please do following:
If Firefox is already included in your Linux distribution or if you have installed Firefox with the package manager of your Linux distribution:
# Close your Firefox.
# In '''Terminal''' run: <br/> <code>firefox -P</code>
# To start the Create Profile Wizard, click '''Create Profile...''' Button in the Profile Manager.
# Click {button Next} and enter the name of the profile. Use a profile name that is descriptive, such as your personal name. This name is not exposed on the Internet.
# To create the new profile, click '''Finish'''
For more instruction regarding creating a new profile, please see this article. [[Use the Profile Manager to create and remove Firefox profiles]] -
Sync fails with "Unknown Error" no clear UI shows what happened
I'm using the latest Firefox 3.6 with the latest sync extension on some machines and the latest Firefox beta (4.0b6) on another machine. A few weeks ago the sync stopped work on my Firefox Beta and the only error I could see is: Error while syncing: Unknown error.
I took the time today to to see what happens and saw on the log (about:sync-log) that:
2010-10-20 13:17:02 Net.Resource DEBUG GET success 200 https://phx-sync054.services.mozilla.com/1.0/dcordeiro/info/collections
2010-10-20 13:17:02 Net.Resource DEBUG GET success 200 https://phx-sync054.services.mozilla.com/1.0/dcordeiro/storage/meta/global
2010-10-20 13:17:02 Service.Main DEBUG Weave Version: @weave_version@ Local Storage: 2 Remote Storage: 3
2010-10-20 13:17:02 Service.Main WARN Upgrade required to access newer storage version.
2010-10-20 13:17:02 Service.Main CONFIG Starting backoff, next sync at:Wed Oct 20 2010 16:22:39 GMT-0200 (BRT)
2010-10-20 13:17:02 Service.Main DEBUG Exception: aborting sync, remote setup failed No traceback available
This raises two questions. First, the UI does not shows exactly what happened. This kind of issues with upgrades on the sync platform should be expected.
Second, this shows that a regular user shouldn't be using sync with different Firefox versions. This is quite usual, I think (a more stable version on work and newer version on home) and should be expected.Error: The Microsoft Software License Terms have not been completely downloaded and cannot be accepted.
Sync failed: Failed to sync some of the updates. Source: Microsoft.SystemsManagementServer.SoftwareUpdatesManagement.WsusSyncAction.WSyncAction.SyncUpdates $$<SMS_WSUS_SYNC_MANAGER>
Too many consecutive failures. Aborting sync. $$<SMS_WSUS_SYNC_MANAGER>
Any suggestions would be appreciated.
Even I had similar issue however it got resolved by itself, so it could be something to do with external to CM12 as Umair mentioned. Also some more details troubleshooting and solution available in the following thread http://social.technet.microsoft.com/Forums/en-US/09ed08ef-876e-493d-b139-6fc3d9500447/sccm-software-update-errorlicense-terms-could-not-be-downloaded?forum=configmanagerdeployment
Anoop C Nair (My Blog www.AnoopCNair.com)
- Twitter @anoopmannur -
FaceBook Forum For SCCM -
Ipad2 restore fails with unknown error(1) with "iTunes and recovery" mode logo
Ipad2 64GB was sluggish and we tried to update with latest iOS update, security 2014-005 and latest iTunes on iMac 12.01 It enters a recoverymode with the iTunes logo and connector symbol displayed on the screen. Recognized that iPad is connected and proceeded to restore to factory condition. Goes through several stages, FW verification, restore etc but fails to proceed past a certain point and puts up an unknown error (1) occurred message. Disabled firewall and tried restore and it failed in the same spot. Tried using power + home button combos to enter DFW or restore mode. None of them worked. Took it to the Apple store and was told that it can't be debugged further because it did not yet boot up ( if it has the iTunes and connector symbol it must be in some state that it can be interacted with?) It's physically in a perfectly beautiful condition, nothing funky (jail breaking etc ) done to it, well taken care of. The tech said that he can offer a replacement for 299$ after he tried to restore it twice without success. I am surprised that this tech thinks that it cannot be probed with some low level FW tools through the serial connector to determine the system state. Any suggestions?
Hey Ngtrishank,
Thanks for the question. Based on the information you have provided, I concur with the Apple Store’s conclusion. Error 1 is usually related to a hardware issue with the device. While there are a few steps you can attempt in the following resource, in most cases Error 1 signifies that the device needs to be serviced. For more information on troubleshooting Error 1, see this article:
Resolve iOS update and restore errors - Apple Support
http://support.apple.com/en-us/ts3694
Check for hardware issues
Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
These errors mean that your device or computer may have a hardware issue that's preventing the update or restore from completing.
If you’d like to learn more about your Service options for this device, check out the following link:
iPad Other Repair Options - Apple Support
http://www.apple.com/support/ipad/repair/other/
Thanks,
Matt M. -
BPM getting failed with unknown error in inbound queue
Hi ,
I am using BPM for simple IDOC collection( time based collection) .Its working fine also .However once it fail we can see the BPE failed in inbound processing error in smq2 and status is system faliure.
on debugging we can see a unknown error in transformation step that error in conversion [NN]. to proxy Z_interface name ( the proxy which automatically get created for transformation step. ) data related issue.
When we check the same input data in IR its working fine in message mapping . we are unable to find any other error either in BPM or in the input data.
The most surprising thing is that when we deleted the message from queue and re-triggered the IDOC once again from SAP system then its worked fine .
Can any body kindly suggest what can be the probable reason of this .As we are afraid that if the same thing will happen in production what we will do without any expalination we can't delete queue and retrigger IDOCs there.
Regards,
saurabhOne option would be to raise an exception for such steps....in the Exception handler you can repeat the same step....in your case it will be the mapping (n:1) .....are you sure that the process failed in Transformation step and that the data was correct....i mean all the 5 IDOCs were sent as an input to the mapping?
Can you ensure that during this time there was no connection issue between the BPM and the mapping runtime (IE)....may be you can check with your BASIS.
Regards,
Abhishek. -
My uploads to Facebook fail with Unknown Error
Every attempt to upload my projects to Facebook fail with the message "Error, Unknown Error" message.
I have tried projects from 15 down to just 5 minutes.
I have tried projects with 6 down to just 1 clip.
I have tried wireless and wired connections.
I went into preferences and reset my web settings, then rebooted.
I have tried online "live" support (useless).
So here are a few screen captures of how my attempts to share to facebook go:
It renders ok...
It Uploads ok...
It gets all the way to the last few seconds in the transferring step...
then errors out...
Can anyone suggest anything I can try?Try using Publish & Share/Computer/AVCHD with the YouTube preset -- then manually upload the file to YouTube.
Although Adobe tries to keep up with it, YouTube continues to be a bit of a moving target, when it comes to interfacing with it. Rather than fight with it, I find it's best to just output an AVC/Mp4 file and load it to the site myself. -
PC Companion - Outlook sync fails with unknown error
trying a sync with outlook 2010 leads to an unknown error, the log reads:
09:18:29,37 [PCCompanion 14/09/11] Activate CalendarManager
09:18:45,15 [MapiThk 13/05/06] Outlook 2010 detected.
09:18:45,15 [Syncengine 13/05/22] Get default PIM database name 3
09:18:45,18 [Syncengine 13/05/22] Result \\Microsoft Exchange.pst
09:18:45,22 [Syncengine 13/05/22] Get default PIM database name 11
09:18:45,22 [Syncengine 13/05/22] Result \\WindowsContacts.cts
09:18:45,22 [PCCompanion 14/09/11] Activate Synchronization
09:19:19,65 [Device 14/09/18] Check device status...
09:19:19,65 [Device 14/09/18] Check device status finished.
09:19:47,14 [CAgdOutlook 13/01/08] InitAutomation
09:19:47,14 [CAgdOutlook 13/01/08] OpenCalendar
09:19:47,14 [CAgdOutlook 13/01/08] -------------------------------------------------------
09:19:47,14 [CAgdOutlook 13/01/08] m_hLibrary FAILED
PC Companion 2.10.228
Solved!
Go to Solution.Glad to hear that it works now
In case it happens again, try to manually select the folders you want to synchronize with in MS Outlook. In PC Companion, click Settings when you're in the synchronization app and the select the option for personal data on the left and then click Properties for Contacts and Calendar to select folder.
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page. -
DPM 2012 R2 - update roll up 2 failed with fatal error
i successfully updated DPM to rollup 1 , but when i try to install roll up 2 i get " Fatal Error"
i tried reboot the server still same issue.
I ve pasted the log below , is anyone able to point me on the right path to get it updated successfully ?here are some of the failure points
0F10 1FBC 03/25 19:52:26.070 10 main.cpp(1958)
WARNING Failed: Hr: = [0x80070426] StopService failed for service[VssNullProvider] and returned
0F10 1FBC 03/25 19:52:32.835 10 main.cpp(1848)
WARNING Trying to open windows service failed for Service = [VssNullProvider]
0F10 1FBC 03/25 19:52:32.835 10 main.cpp(1849)
WARNING Failed: Hr: = [0x80070424] : Encountered Failure: : lVal : hr
0F10 1FBC 03/25 19:52:32.835 10 main.cpp(2049)
WARNING Failed: Hr: = [0x80070424] : Encountered Failure: : lVal : GetServiceHandle(schSCManager, lpService, hService)
0698 0680 03/25 21:28:08.854 18 dsmsendersubtaskbase.cpp(646)
[00000000015E3A40] 0CE35248-6FF7-4B20-B989-1EA86BB1F84B NORMAL
Failed to read MaxBufferSize from registry. Using default size: 262144
0698 0680 03/25 21:28:08.886 20 nativeutils.hpp(42)
0CE35248-6FF7-4B20-B989-1EA86BB1F84B WARNING Failed: Hr: = [0x80070002] : Encountered Failure: : lVal : r.GetValue(pszKey, pT)
0698 0A6C 03/25 21:28:08.901 20 cc_session.cpp(161) [000000000161A3E0]
0CE35248-6FF7-4B20-B989-1EA86BB1F84B NORMAL Hr: = [0x80070002] DM: SetTcpSendWindow failed for connection 000000000161A3E0, Ignoring the failure
0698 0B2C 03/25 21:28:13.261 06 coorddefaultsubtask.cpp(586) [00000000015E1AD0]
0CE35248-6FF7-4B20-B989-1EA86BB1F84B WARNING Failed: Hr: = [0x80990a11] : Encountered Failure: : lVal : FindWorkItem(pCommand->m_guidWorkItem,
workItem)
0698 0B2C 03/25 21:28:13.261 06 coorddefaultsubtask.cpp(157) [00000000015E1AD0]
0CE35248-6FF7-4B20-B989-1EA86BB1F84B WARNING Failed: Hr: = [0x80990a11] : Encountered Failure: : lVal : pCoordCommand->Dispatch()
0698 0B2C 03/25 21:28:13.261 05 defaultsubtask.cpp(546)
[00000000015E1AD0] 0CE35248-6FF7-4B20-B989-1EA86BB1F84B WARNING Failed: Hr: = [0x80990a11] : Encountered
Failure: : lVal : CommandReceivedSpecific(pCommand, pOvl)
0698 0B2C 03/25 21:28:13.261 05 defaultsubtask.cpp(751)
[00000000015E1AD0] 0CE35248-6FF7-4B20-B989-1EA86BB1F84B WARNING Failed: Hr: = [0x80990a11] : Encountered
Failure: : lVal : CommandReceived(pAgentOvl)
0698 0B2C 03/25 21:28:13.261 03 runtime.cpp(1376)
[00000000015A2160] 0CE35248-6FF7-4B20-B989-1EA86BB1F84B FATAL ] -
Mac OS X 10.6.7, Firefox 4.0.1.
Sync Now from the menu likewise fails.
Attempting to get the sync quotas from the Preferences also comes back with a similar error.To add a clarifying point in my case, which may or may not be universal for the others having this problem as well: it came within minutes of the update to 4.0.1, so it seems likely it has to do with the new version. OP said it used to work but started happening recently, so it could be the same cause as mine, given the recent release of the update, and OP's indication that 4.0.1 is also in use.
-
I followed the same procedure in adding a device for the second and for the third. The second one worked, but not the third.
As far as I know, all software is up to date.ok.. I tried this three times and kept getting that access denied thing when I clicked post my questions. So now maybe I wont have to typ this a fifth time....
I have a MAC computer with Sync. Was set up under sync Beta. I have an Android phone synced to it that was synced using the pair this device function. It works perfectly. I just got a new Android Tablet and am trying to add it to my sync and it does not seem to have the pair my device function. It insists I log into my sync account. So I try it and it tells me invalid userid/password. I verify and it is the exact email address userid that shows as being my sync account on the MAC. I verify the password on the MAC and it tests out fine. Try the tablet again and invalid.. So I try to reset my password on the tablet and am told my email address/account name does not exist. I just verified it AND Synced my MAC using it!! I have my recovery Key but there is no place to input it into the tablet. There is no place on tablet to enter the link device codes. How can my account be valid and in use on two devices but invalid and nonexistant on the new one? And How do I get the New one to sync with other two? -
Mappingtool fails with unknown error
Hello,
I keep trying to learn JDO with KODO, but I've hit another roadblock.
I've created a basic metadata file, then ran jdoc on it which was fine.
However, when trying to run mappingtool, I get the following error:
0 INFO [main] kodo.Tool - Mapping tool running on type "class
edu.uiuc.cs427.domain.Market" with action "refresh".
297 INFO [main] kodo.Tool - Mapping tool running on type "class
edu.uiuc.cs427.domain.MarketContainer" with action "refresh".
297 INFO [main] kodo.Tool - Mapping tool running on type "class
edu.uiuc.cs427.domain.TradingSettings" with action "refresh".
297 INFO [main] kodo.Tool - Recording mapping and schema changes.
Exception in thread "main" kodo.util.FatalInternalException: The
metadata for type "class edu.uiuc.cs427.domain.Market" did not come from
a file, and
therefore we cannot determine where to place the corresponding mapping
information. If you are using metadata from a jar or other resource,
you shoul
d use one of the other available mapping factories.
at
kodo.jdbc.meta.FileMappingFactory.getMappingFile(FileMappingFactory.java:203)
at
kodo.jdbc.meta.FileMappingFactory.storeMappings(FileMappingFactory.java:139)
at kodo.jdbc.meta.MappingTool.record(MappingTool.java:454)
at kodo.jdbc.meta.MappingTool.run(MappingTool.java:870)
at kodo.jdbc.meta.MappingTool.main(MappingTool.java:801)
The metadata is surely from the file package.jdo, so I don't know why
it's saying it did not come from a file.
Here's my package.jdo:
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE jdo PUBLIC "-//Sun Microsystems, Inc.//DTD Java Data Objects
Metadata 1.0//EN" "http://java.sun.com/dtd/jdo_1_0.dtd">
<jdo>
<package name="edu.uiuc.cs427.domain">
<class name="Market"
identity-type="datastore"
persistence-capable-superclass="edu.uiuc.cs427.domain.MarketContainer"
> <!-- end class tag -->
</class>
<class name="MarketContainer"
identity-type="datastore"
> <!-- end class tag -->
<field name="tradingSettings"
> <!-- end field tag -->
</field>
<field name="children"
> <!-- end field tag -->
<collection
element-type="edu.uiuc.cs427.domain.MarketContainer"
embedded-element="false"
> <!-- end collection tag -->
</collection>
</field>
<field name="parent"
> <!-- end field tag -->
</field>
<field name="name"
> <!-- end field tag -->
</field>
</class>
<class name="TradingSettings"
identity-type="datastore"
> <!-- end class tag -->
</class>
</package>
<!--
To use additional vendor extensions, create a vendor-extensions.xml
file that
contains the additional extensions (in extension tags) and place it
in your
projects merge dir.
-->
</jdo>I have some more information on this:
I tried changing the MappingFactory to metadata instead of the default
file. When I do this, I do not get an error, but nothing gets added to
my package.jdo file either.
It seems like the file I/O is simply not working here for some reason.
When I choose the db MappingFactory, the mapping information gets put in
the database correctly. When I give mappingtool the -f option it will
output the file correctly. However, the default file or metadata are
simply not doing proper I/O. I'd like to stick with the default file
MappingFactory.
I'm using Windows XP, I start up a command prompt using the jdoCmd.bat
file, I go to my build's classes directory which has the proper
package.jdo file at the base, and then I run:
jdoc package.jdo (works fine)
mappingtool -a refresh package.jdo
Any help on this problem?
Thanks
Don Diego wrote:
Hello,
I keep trying to learn JDO with KODO, but I've hit another
roadblock. I've created a basic metadata file, then ran jdoc on it which
was fine. However, when trying to run mappingtool, I get the following
error:
0 INFO [main] kodo.Tool - Mapping tool running on type "class
edu.uiuc.cs427.domain.Market" with action "refresh".
297 INFO [main] kodo.Tool - Mapping tool running on type "class
edu.uiuc.cs427.domain.MarketContainer" with action "refresh".
297 INFO [main] kodo.Tool - Mapping tool running on type "class
edu.uiuc.cs427.domain.TradingSettings" with action "refresh".
297 INFO [main] kodo.Tool - Recording mapping and schema changes.
Exception in thread "main" kodo.util.FatalInternalException: The
metadata for type "class edu.uiuc.cs427.domain.Market" did not come from
a file, and
therefore we cannot determine where to place the corresponding mapping
information. If you are using metadata from a jar or other resource,
you shoul
d use one of the other available mapping factories.
at
kodo.jdbc.meta.FileMappingFactory.getMappingFile(FileMappingFactory.java:203)
at
kodo.jdbc.meta.FileMappingFactory.storeMappings(FileMappingFactory.java:139)
at kodo.jdbc.meta.MappingTool.record(MappingTool.java:454)
at kodo.jdbc.meta.MappingTool.run(MappingTool.java:870)
at kodo.jdbc.meta.MappingTool.main(MappingTool.java:801)
The metadata is surely from the file package.jdo, so I don't know why
it's saying it did not come from a file.
Here's my package.jdo:
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE jdo PUBLIC "-//Sun Microsystems, Inc.//DTD Java Data Objects
Metadata 1.0//EN" "http://java.sun.com/dtd/jdo_1_0.dtd">
<jdo>
<package name="edu.uiuc.cs427.domain">
<class name="Market"
identity-type="datastore"
persistence-capable-superclass="edu.uiuc.cs427.domain.MarketContainer"
<!-- end class tag --></class>
<class name="MarketContainer"
identity-type="datastore"
<!-- end class tag --><field name="tradingSettings"
<!-- end field tag --></field>
<field name="children"
<!-- end field tag --><collection
element-type="edu.uiuc.cs427.domain.MarketContainer"
embedded-element="false"
<!-- end collection tag --></collection>
</field>
<field name="parent"
<!-- end field tag --></field>
<field name="name"
<!-- end field tag --></field>
</class>
<class name="TradingSettings"
identity-type="datastore"
<!-- end class tag --></class>
</package>
<!--
To use additional vendor extensions, create a vendor-extensions.xml
file that
contains the additional extensions (in extension tags) and place it
in your
projects merge dir.
-->
</jdo>
Maybe you are looking for
-
My modem is down and can I get the jump-drive to install OS X Lion?
I was informed by my ISP (Hughes.net) that my modem is not functioning to download large files. They are sending a new modem; in the meantime I paid for the Lion upgrade and cannot install it. Can I get the jump-drive sent to me?
-
Regarding Receiver Communication Channel (Concurrency problem)
Hi Masters , In Receiver Communication Channel which is connected to oracle data base ..while updating records Status from N to C . i am getting following errors : **Message processing failed. Cause: com.sap.aii.af.ra.ms.api.RecoverableException: Cha
-
Number of elements in an array
Hi, I have been trying looking for a simple function to get number of elements is an array. Have gone though older posts but could not find answer to it. The function should work for following examples: char* name = "nInstruments" float state[] = {1.
-
Forecasting in DP: At aggregate level or at detailed level?
Hello All, I have selection ID in APO DP 4.0 comprising of may products. I forecast them as a whole using some forecast method (may be seasonality method). How SAP DP forecasts? Does it individually forecast for each product or does it forecast at ag
-
Scripting error changing field required state
I need to update all fields in a document to be not required. I read the value but cannot set it. I get the following error in the debugger. NotAllowedError: Security settings prevent access to this property or method. Field.required:10:click undefin