Iphone3g 2.01 - wlan: unable to join the network "xyz" with netgear dg834n
i m not able to connect to my netgear dg834n with my new iphone.
every time i´m trying it i get this error:
unable to join the network "xyz"
tests i did:
- restart of iphone
- reboot of iphone
- switching of security (and mac address control) on netgear
- tryout of all wlan security combinations on netgear
- turned netgear off and tried again
- dhcp and manal settings on iphone for tcp/ip (netgear has dhcp enabled)
i m using the newest available firmware for dg834n
any help ?
Add me to the list. . .and it happened right after the upgrade to 4.2.1. . .
Coincidence or just just a factor of wear and tear. I've tried 3 calls to Apple and they say the phone needs to be replaced.
A bunch of youTube videos watched and instructions followed to no avail.
It seems that the wireless portion of the circuit board connection is prone to cracking in the iPhone. I'm finding references to this gremlin dating all the way back to 2008. I'm wondering if there is a connection with high swings in temperature of surroundings. One clue to whether cracking exists on Circuit board connections is to pop your phone into a freezer for about 10 minutes and see if this permanently or temporarily allows the phone to be able to connect. . .
The only successful fix I've seen is reflowing the Circuit board by putting it in the oven but that takes a couple of shots of good vodka before seriously trying that. . .There are plenty of Google links on both the preparation and the fix. . .8^]
Similar Messages
-
My i-phone cannot connect to my wi fi-all of a suddon. My wife's i-phone 4 is connected to the wi-fi network.
I just tried to connect my daughter's i-phone 5, and could not connect message came up "unable to join the network "Sunday".
My I-pad is connected to Sunday also.
I tried the reset routine, and when I try to get on line, it asks for my password. I put it in and it stll says unable to hoin message.
Can someone help?Reset your network settings. Settings>General>Reset>Reset Network Settings
-
Just installed iOS 7.0.4 on the ipad, and can no longer connect to my home locked wifi. I choose the home wifi network and the message comes back with Unable to join the network "............" Dismiss. There is no prompt for the password for the locked network. . . . Any suggestions . . . . .
1. Turn router off for 30 seconds and on again
2. Settings>General>Reset>Reset Network Settings -
New iPod Unable to join the network after inputting password
Got my iPod this am..
looked too good to touch no pun intended.
I went through the instructions, interrupted with an offer to update_, which I did.
I then saw that the iPod was off line and went to set up the connection.
I do have a Time Capsule but I just use it as an external drive, I use Ethernet connections between it my Netopia router/modem which provides my Wi Fi for another computer.
I have a WPA-PSK security on the Netopia.
My Wi Fi shows up on available networks, I am asked for my password but then I get a message "Unable to join the network"
I must admit that my password is long (and a bit racy) my fingers a bit big, but I know that I have got it right on at least a few occasions.
I have tried entering the details on "Other network" with the same result.
Could my WPA-PSK be a problem?
I would be most grateful for any suggestions.
Various forms of this problem have appeared on this forum, but I think mine is a bit different.
Thank you.Thank you.
Went through that pretty well.
Finally solved it in 2 steps.
1. reset my modem/router to factory settings.
Odd situation, wireless settings, but dependent on ethernet connection.
2. read a post from Hong Kong re strange network settings.
On his advice, into network, changed location from Automatic to one of my choosing.
Bingo! everything came good.
Totally wireless connection. iPod jumped to it. Isn't it great when everything comes together?
I still wonder why it didn't take the signal from the WiFi part of my Modem/Router?
Probably just as well as it sorted my Time Capsule connections out, probably for the first time since I bought one back in early 2008, and its recent replacement when it joined the epidemic of sudden death recently.
Cheers -
I just returned from Europe and my ipad will not join my home WiFi network. It keeps giving me the message "Unable to join the network" Any ideas?
I turned off my airplane mode."That was Easy!" Thanks!
-
I bought a used i-pod touch 4 gen that I'm trying to set up. It isn't lettting me join my home wi-fi network. So I turn it on and I pick language, then country , then my wi-fi network. When I put in my password is says - unable to join the network. I have 4 other Apple products that I have that are working fine. Please help
Badunit you said "Continue setting up without the network. You can skip past it, right?"
It sounds like he is setting up the iPod via wif. You can't continue. What yo can do is reset the iPod
- Reset the iOS device.
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Then start the setup over again but this time connect the iPod to a computer and set up via iTunes. Then he can troubleshoot the connection proboem. -
When I try to connect to the wi-fi net work at my work place on my new iPad 3 I get a message, "unable to join the network". I have verified the password, so I know it is correct. I know the wi-fi works, because I can connect at home. I have already tried the following:
turn wi-fi off and on again
did a hard restart of my iPad
reset network connections back to factory settings
verified wi-fi is working as my computer accesses internet without issue.
verified that my software is up to date.
Does anyone have more suggestions?Couple of suggestions.
First, many companies have a gateway on their networks that block non approved devices. I work in such a place. You might check with an IT guy , and see if they have a block in place.
Second, the message you are getting means that you have not negotiated the security settings. So either the password is wrong ( case sensitive), or, in some cases, they want a network key as opposed to your normal password.
Again, if you can find one, talk to an IT guy and see if he has some suggestions. -
IPhone 5 wi-fi "unable to join the network"
My new iPhone 5 is my first iPhone and I've had it about a week. I'm still in the process of setting it up but cannot connect to my home (secured) wi-fi. I've been reading other Apple forums and Google suggestions and it appears this is a known Apple issue? My phone came with iOS 6 installed so I have no update available. I've turned off my router and shut off my phone, rebooting both but I still get an error message when entering our wi-fi password: "unable to join the network". I've turned off cellular and re-tried wi-fi to no avail. I am NOT impressed with my first Apple product. What a hassle. Does anyone have any other suggestions to try or am I stuck waiting months for an Apple fix?
There are a couple of things that you can try. First, try disabling the security on your wifi network and see if the phone will connect. Check the type of security you are using. Some have reported the iPhone reacts differently to some wifi security. Check to see if there is a firmware update to the router. This is usually the biggest culprit of the bunch. Once routers have been updated and restarted, troubles disappear.
-
I had no problem connecting to my network and now all of a sudden I can't connect my iPad. Instead of prompting me for a password it comes back and says unable to join the network ("name") and then the option is Dismiss. Anyone else have that problem? I've gone thru all my settings and can't seem to find a way to log into my network. Don't get the option to put in my password. It just give me the name of my network and option of dismiss instead of password.
1. Turn router off for 30 seconds and on again
2. Settings>General>Reset>Reset Network Settings -
Unable to Join the network ...
I've seen similar posts with the same title but none of these solutions work for me. The problem is that I can not connect to my home Wi-Fi network. Following are the details:
- I have a new iPod Touch with OS 2.2.1
- My wireless router is an Airport Extreme running 7.4.2
- My wireless security is WPA2 Personal
- I have no problem connecting other devices such as Mac laptops and desktops so I know the correct password and the usual settings
- I have also been able to connect my Touch to another wireless network with WPA2 security! This leaves me to believe there must be some incompatible setting on my Airport Extreme.
- I have gone through the various trouble-shooting steps on Apple's support site, to no avail. I have reset both the Touch and the Airport many times
- The Touch can see my network but when I enter the (correct) password I get the error "Unable to Join the Network ..."
Any help would be appreciated! I can certainly take my Touch to my local genius bar, but that won't help if the problem is with my Apple wireless router.If you can see your network, then you are at least not making the same mistake as many AE users - leaving the router broadcasting in N mode only.
Are you using anything like MAC address filtering on your network? Is DHCP on? The easiest thing you can try is a) reset the touch network settings; b) log back into your network using Settings > WiFi > Other network and re-entering your network name (case sensitive), security, and password (also case sensitive).
Try that and let us know what happens. -
After getting 4G with AT&T I am unable to join my network and get the error message: Unable to join the network "Jude". How do I fix this? Thank yo
Try power-cycling your wireless router (unplg for 30 seconds, plug back in). Here's a longer list of troubleshooting steps: http://support.apple.com/kb/TS1398.
-
I have a new Apple iPad2 which will not connect to my wi fi despite a new router. When I tap the correct address it comes up with the message "Unable to join the network TalkTalketc... It does connect in other peoples' houses . Am I right in thinking that the trouble is with TalkTalk?
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
im on pay as you go.. still trying to set up wifi to my home network.. im putting in the password (sky broadband) and i keep getting the message
Unable to join the network...
driving me crazy now - please help !Other possibilities:
Your router firmware is out of date. Check the manufacturer's website for an update
You have MAC (Media Access Control) filtering enabled on the router, that restricts access to "known" devices and the new iPhone is not on the table of known devices
Your router has a setting limiting the number of simultaneous allowed devices
Your routers SSID ("name") is still the default (e.g., LINKSYS, DLINK, NETGEAR, etc). Your phone has encountered other routers with the same name as you have traveled, and the phone is confused as to which router is the real one. If your router's name is still the default you should change it. -
How to solve the issue of 'Unable to join the network' on my iPhone 5!?
I used to connect to a wifi network on my iPhone 5 and suddenly i could not connect anymore to this network. My phone kept showing 'Unable to join the network'. I tried 'forget this network' and resetting the network settings but none of these solutions worked. Can anyone help me to resolve this issue?
Hi Jason,
Please try with scope provided: Maven – Introduction to the Dependency Mechanism
Kind Regards,
Alex -
Recently, my iphone 4s lost connection with the wifi network I set up on my imac desktop. The message I receive is "unable to join the network..."
Can anyone offer a solution to this problem? Thanks!Oh, so the problem has nothing at all to do with the iPhone ... it is that you cannot remember the network password! No wonder the iPhone cannot join the network.
Why not simply destroy the network and set up a new one with a password you remember?
Maybe you are looking for
-
HP U160 with Windows 8.1 Surface Pro3
I have recently purchased a Surface Pro3 and I own the HP U160 portable monitor. The monitor works with all of my other laptops running Windows 7, but I can't get it to work with Windows 8.1. I updated the drivers on the HP website for Windows 8, b
-
Hi All! When i create an Addon Application I Register String to connect to SAp by: Right click in my app/properties/Debug/ and input command line Agruments. And in myclasses I call: Private Sub SetApplication() '// Use an SboGuiApi object to
-
Hi,,, does anyone guide me with abap sample code using EOIO? thanks dennis ogawa Dennis
-
1333 or 1600 worth extra 360 $?
Dear Gentlemen!I was so inattentive that I bought this type memory for my X79 platform (i7 3930K): G.Skill 32GB 2133MHz (that time this was on stock, and the seller said there will not be any problem) Now I read about the memory problem with I7 3930K
-
How to extend plant to sales organization
What is the TCode?