IPod Touch 3G w/ stopped working with car stereo/docking speakers

After I upgraded to OS 4, my iPod Touch 3g stopped working through the USB port of my car stereo (just says "reading" and never progresses from there). It also stopped working through the docking station (basically a large clock radio) that I bought for my living room -- it will recharge and play music through the speakers but the docking station and its remote can no longer control the music (can't advance to the next song or anything else), so I have to physically change things on the ipod itself.
I was told by Crutchfield (where I'd purchased the car stereo) that this was a known problem with Apple -- that with OS4, many of the devices that previous worked with iPods no longer worked, and that this would be resolved in a later version of the OS that would provide some backward compatibility. However, I can't find anything at all about this.
If anyone knows more information about this, or has a link to where I might be able to read more, I'd appreciate the info. I selected and installed both the (almost new!!) car stereo and docking station specifically because they allowed me to connect and control my iPod, and now I've lost that functionality and the $$ I put into those devices (over $300 total)!

I apologize for posting a bit early.  Found an Alpine manual online and i needed to set the AUX port to off.  They also recommended a reset of the Touch.  After doing these two things it is now working.  Maybe this will help someone else.

Similar Messages

  • IPod Touch Stopped Working With Car Stereo

    Hello Everyone,
    I have an iPod Touch 4th generation that was working perfectly with the after market car stereo in my truck  The Stereo is an Alpine CDE-102 and I am using the iPod interface and correct cable.  After upgrading to IOS6 the car stereo fails to reconize the device and "SEARCHING" for a few minutes then gives the response "error - 1".  Has anyone else seen this or know of a solution?  Thanks!

    I apologize for posting a bit early.  Found an Alpine manual online and i needed to set the AUX port to off.  They also recommended a reset of the Touch.  After doing these two things it is now working.  Maybe this will help someone else.

  • My daughters imessage on her ipod touch has just stopped working - to get it going again I reset it with my email address but this doesn't allow her to send messages to any of her contacts.  When I try and put her email back in it says it can't verify it

    My daughters imessage & face time on her ipod touch has suddenly stopped working.  The only way i could get it going again was to reset it up with my email address.  This will not allow her to send messages to any of her contacts in her addess book.  I have tried to set up her email (which she previously used successfully) but it will not allow this it states 'unable to verify email because it is already in use' - anyone any ideas its is driving me mad !!

    Try here:
    iOS: FaceTime is 'Unable to verify email because it is in use'

  • I have and ipod touch 4g, it stop working out of nothing, tried everything..

    i have and ipod touch 4g, it stop working out of nothing, i tried to restore, i plugged in to another computer and to the outlet wall and nothing, didnt drop it or got wet, someone told me that it happens sometimes with this ipod generation. what can i do? i bought it to years ago.

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • The speakers on my iPod Touch 2nd generation stopped working.

    The speakers on my iPod Touch 2nd generation stopped working.  The volume doesn't even register - can't turn it up or down.  On occasion the headphones will work when plugged in.  Turned it off and on, tried reset, nothing works.  I bought it second hand so no AppleCare. What can I do?

    Try restoring the iPod via iTunes on your computer.  First from backup and if problem persists restore to factory defaults/new iPod.

  • HT1222 Hello,after the last apdate iOS 7.1.1 my iphone has stop work with the bose dock station. why it is happens?

    Hello,after the last apdate iOS 7.1.1 my iphone has stop work with the bose dock station. why it is happens?

    Natan turbo hadar,
    I have the same exact problem.
    I put an iPod shuffle on the Bose system, it plays just fine.
    My iPhone 4s works just fine connected to my car stereo.
    My iPhone 4s on the Bose will charge, it "thinks" it's playing, song shows, time line shows it's playing, can pause if I touch the phone's screen.
    The remote for the Bose WILL NOT pause it, forward to next song, etc. It does work with the iPod shuffle.
    So it's not the Bose, it's not connections, it's the iOS 7.1.1
    Everything worked fine before, any one else have suggestions?

  • IPhone 2.2.1 software on my iPod touch isn't recognized by my car stereo...

    Hey, First ever post in an online discussion. Hope I'm doin' this right...
    I'm trying to restore the factory software to my first generation 32G ipod touch from my MacBook because my car stereo does not recognize the new software. (my MacBook doesn't have iphone 2.2.1 installed, and Apple support told me a factory settings restore from my MacBook to my iPod touch is my only hope). It seems I can't do an old fashioned restore because my MacBook doesn't even see the iPod (presumably because the iPod has the newest software and the laptop doesn't).
    Anyone... Bueller...?

    All I can suggest is to make an appointment at the Genius Bar of an Apple store
    Apple Retail Store - Genius Bar          

  • IPod touch 2G does't work with Kenwood car radio anymore

    Hi
    since a few days ago, my iPod touch 2G does not work anymore with my car radio Kenwood KDC-W4544U.
    When i connect the iPod to the radio, the radio display shows "Reading", which it normally shows for like 5 seconds. But now the "Reading" lasts forever, after 10 minutes of trying to let my radio read the iPod, i have no other possibility but listen to CD or radio...
    I have already shut down and restarted the iPod, synched it, even restored it via iTunes. I also tried three different connection cables.
    Is this a known problem and is there maybe a solution?
    Thanks in advance for an answer

    Problem could be solved by hard-resetting the radio

  • IPod touch 1g not charging properly with car charger

    I have a 1g iPod touch I'm using it with a Kensington 33199 fm transmitter/car charger. The iPod does not recognize the car charger power to put it into charge mode. The battery symbol does not change to a charging symbol...the unit does play audio out through the transmitter (which works fine), but it doesn't show the usual signs of charging. It seems to get a bit of a charge as the battery doesn't run down, but it also doesn't charge up. If I let the battery run down too far it won't work with the transmitter/charger at all.
    Anyone have this kind of problem with a car charger? It charges fine hooked to the computer or directly to an apple wall charger.

    If this is a 1G, then it should work. I haven't tried my 1G in the car yet, guess I should. I use a Griffin FM transmitter that charges as it plays back over the radio.
    I'll let you know what I find!

  • My ipod touch is no longer working with universal dock since downloading the new OS

    I have the Apple Universal Dock.  It had been working fine with my ipod touch.  I just downloaded the new OS and now my ipod touch will not work with the Universal Dock.
    Any ideas?

    Hi grecokev,
    Thank you for contributing to the Apple Support Communities.
    You mention that your iPod nano is no longer recognized by iTunes after an update. Reinstalling iTunes is a good troubleshooting step, and if the device still doesn't appear in iTunes, try the following steps next:
    Turn off your computer and your iOS device or iPod, then turn them on again.
    Check to make sure that you've installed all required updates for your computer.
    Verify that the 30-pin to USB cable or Lightning Connector to USB cable is free of debris and not damaged. If another cable is available, test with that cable instead.
    USB cables that are bundled with third-party products or accessories might work only to charge those products and might not transmit data. Also, if you're using a third-party case or extended battery pack, try removing the case and connecting the Apple-supplied USB cable directly to your device.
    You can find these steps in this troubleshooting article:
    iPhone, iPad, or iPod not recognized in iTunes for Windows - Apple Support
    If the steps above don't solve it, see the section of the article called "Verify that Apple Mobile Device Support is installed" for some additional steps to try on your PC.
    Best Regards,
    Jeremy

  • IPod Touch no longer works with car stereo after 4.0 update

    I updated my iPod to 4.0 a couple of days ago, and my Hyundai Santa Fe's built-in iPod interface no longer recognizes my iPod's music - it just says "empty iPod" or something of that nature. Is anyone else having this problem?? What should I do?

    Add me to the list. Brand blankety-new ipod touch that after 4.0.2 wouldn't work with the Subaru-factory-installed ipod connector in my '08 STI. The shut-it-off-and-restart-in-the-car method at least made it able to play music again but still no recharging.
    To add insult to injury I did the have-an-Apple-GENIUS call me thing. The first thing was that they called me....for about 1/4 of a second. The phone blipped for less than a ring and then I got an email saying, "Oh, we TRIED to reach you and you weren't there. Why don't you call us?". So I called and was immediately put on hold. When one of the geniuses finally picked up, I described the issue with great patience and his insightful answer was, "let me put you on hold while I talk to my supervisor." So I sat on hold for five minutes until...they just hung up...no answer, no, "gee we think you're SOL"....just "click". Thanks a boatload Mr. Jobs.

  • My original ipod touch charger has stopped working?

    I have a 32gb ipod touch 5th generation with an original ipod touch charger. It just stopped working one day and I couldn't charge my ipod anymore, I thought my charger was dead and broken so I decided to buy a new. It worked fine the first week, but then stopped working, is my ipod the problem? please help...

    Was it a genuine Apple cable? If so then if it is defective Apple will exchange it at now cost. Same for the original cable if it was not abused and you purchased the iPod less than a year ago.
    Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar                          

  • Camera on back of my iPod Touch 4 has stopped working, what's happened?

    The camera on the back of the iPod Touch 4G (The one on the silver metallic side) has stopped working completely. The front facing one still works.
    Please help. I have had many problems with the iOS software, and I am getting frustrated!
    Regards,
    Alex.

    Have you tried the standard fixes:
    - Reset the iPod:
    Reset iPod touch:  Press and hold the On/Off Sleep/Wake button and the Home
    button at the same time for at least ten seconds, until the Apple logo appears.
    - Restore the iPod via iTunes.  First from backup and if problems persist restore to factory defaults/new iPod
    - If problem still occurs make an appointment at the Genius Bar of an Apple store since you likely have a hardware problem.  If so, they will give you a replacement under your warranty.

  • Ipod Touch 2nd Generation stopped working..totally dead!

    Hey.
    Hoping that someone out there can help me out..my 2nd generation Ipod Touch has stopped working..wont charge..wont turn on..nada! It did the same thing last week but eventually it charged up and worked again. However this time its totally unresponsive.
    I used it last night..turned it off and awhile later tried to turn it on again but it didnt respond. I tried to charge it overnight but its completely dead. I plugged it into a computer and a window appeared to say that everything is updated but still nothing. When I unplugged it and tried again the wondow did not appear.
    Its had connectivity issues for awhile now but I assumed initially that it was just dodgy internet connections rather than a problem with the Ipod itself..clearly not!!
    Ive tried all the solutions offered on the Apple website but it appears to be totally dead. I only bought it in February this year..its an Apple refurbished model.
    Aside from the obvious frustration of now not being able to use it..to complicate matters I'm travelling in South America for the forseeable future so dont have readily available access to a Apple dealer etc.
    As its still relatively new I should be covered by the warranty but just wondering what anyone out there would advise I do in order to either get it repaired or replaced given that I'm travelling etc.
    Theres no authorized dealers in Cusco where I'm currently living..there appears to be one in Bolivia where I'm heading in a few weeks but I dont even have my receipt with me so I'm not even sure I can get it fixed under the warranty.
    Would really appreciate any advice from someone that is a bit more familiar with Apple products and/or has some advice about warranties etc.
    Many thanks in advance.

    Any chance this could simply be a battery issue????? I do use it a **** of a lot..! Anyone any idea how much new batteries are?

  • IPod no longer works with car stereo since upgraded MBA & iTunes

    My iPod classic has worked just fine connected to my car stereo since i bought it last june. I just bought a new Macbook Air (OS 10.7.3) & installed ITUNES 10.6.1. After I synched my ipod for the first time its recognised by the car but i get a "can't read data" message. I re-formatted my ipod but its exactly the same. Do you think its the upgrade- or the cable? Has anyone else found a bug with this version of Itunes or the OS? I have my doubts a cable would make the difference, and my old ipod nano that i haven't synched for a while works fine.

    If standalone works fine, then, most likely the 30 pin connect may have some dirt or lint, prevent data transfer.
    You can try to blow it clean, if you have a can of compressed air or gas.
    Alternatively you can connect it to the car stereo and do the RESET, while connnected.as follows
    Toggle the Hold switch, make sure you dont see the red mark when you do the  next step
    Reset the iPod -> Press Menu and Center button simultaneously for about 10 secs or till the Apple Logo comes ON
    Then release the buttons
    Select your preferred language.
    Here is the Apple support Article on the 5Rs
    http://www.apple.com/support/ipod/five_rs/classic/
    The Reset sequence may send a signal to the Car stereo to do the right thing

Maybe you are looking for

  • " Screen Tearing" with EVGA GTX 970

    Hi everyone, when watching clips with movement or moving windows on windows somewhere else I get the "tearing effect" on my monitor. Meaning I see vertical lines while movement on my monitors, mainly in the middle. I do not see this line in PP CC 201

  • At new .....statement in ALV

    I have created an ALV report . In the report, the requirement is to display the material name and its description whenever it changes. How can i use the at new matnr...or on change of matnr in an ALV report .. Please help me out.. Thanking you in adv

  • Is there an external graphics card available for the Mac Mini?

    Is there an external graphics card available for the Mac Mini?

  • Workflow for converting PAL DVD to NTSC

    Hi, I have read this thread "http://discussions.apple.com/message.jspa?messageID=7387015#7387015" but am a little unclear and would appreciate some help. I have shot 3 short movies in PAL anamorphic, edited in Final Cut Express HD 3.5, exported using

  • DPM Console crashing.

    DPM Console Crashing. Event ID 948 and 999. Detail error log in eventvwr is below. Please help urgent. The description for Event ID 999 from source MSDPM cannot be found. Either the component that raises this event is not installed on your local comp