IPS event monitor and reports not working

Dear after upgrading my IPS from E3 to E4 the event monitor and reports not working, can you please advice my to solve this issues

Hi All,
Filter settings below:
The filter works partially as I don't get alerts on the IPS itself.
Firewall LOG:
4          Feb 14 2014          15:33:22                              39715                    514          IPS requested to drop UDP packet from SOURCE_VLAN_NUMBER:/39715 to DESTINATION_VLAN_NUMBER:/514
IPS LOG (when enabled):
evIdsAlert: eventId=1352793300955167909 vendor=Cisco severity=low
originator:
    hostId: SSM02
    appName: sensorApp
    appInstanceId: 1192
time: Feb 14, 2014 15:33:22 UTC offset=0 timeZone=GMT00:00
signature:   description=IP Fragment Too Small id=1206 version=S212 type=anomaly created=20030801
    subsigId: 0
    sigDetails: Too many small IP fragments in datagram
interfaceGroup: vs0
vlan: 0
participants:
    attacker:
      addr: 172.x.x.x locality=OUT
      port: 39715
    target:
      addr: x.x.x.x locality=OUT
      port: 514
      os:   idSource=unknown type=unknown relevance=relevant
alertDetails: InterfaceAttributes: context="single_vf" physical="Unknown" backplane="GigabitEthernet0/1" ;
riskRatingValue: 50 targetValueRating=medium attackRelevanceRating=relevant
threatRatingValue: 50
interface: GigabitEthernet0/1 context=single_vf physical=Unknown backplane=GigabitEthernet0/1
protocol: udp
Our next step is to make a service policy exception on the firewall itself. We are also considering reloading the IPS device or at least the analysis engine.
Thanks for all your help so far. Any more suggestions are most welcome. I'll keep you up to date.
Regards
Mariusz

Similar Messages

IPS Event Action Filter is not working properly.

Hi,
We have a local syslog server which listens on UDP 514 port. As many UDP frames has been cut I've done some investigation and found dropped packets (action requested by IPS). This was 1206.0 signature which is "IP Fragmant Too Small". I have created a new entry in IPS Policies to filter this out, but it didn't help. As a test I have disabled the signature completly and all frames have been delivered fine. Another thing I've tried was bringing the new action filter to the top and enabled "Stop on Match" option. Still the same. The only one solution is to disable the signature, but we can't do it.
This is ASA-SSM-20 installed on ASA 5520 version 7.1(6)E4, mode: inline
Bug search tool didn't show any related bugs.
I have checked Database integrity and get "No errors found while performing database integrity checks.
My questions are:
1. What can cause an action to be ignored on IPS?
2. Is it worth to use "Repair Database" tool? If yes what is the impact.
3. Is it possible to check hit counts on each action filter?
Regards
Mariusz

Hi All,
Filter settings below:
The filter works partially as I don't get alerts on the IPS itself.
Firewall LOG:
4          Feb 14 2014          15:33:22                              39715                    514          IPS requested to drop UDP packet from SOURCE_VLAN_NUMBER:/39715 to DESTINATION_VLAN_NUMBER:/514
IPS LOG (when enabled):
evIdsAlert: eventId=1352793300955167909 vendor=Cisco severity=low
originator:
    hostId: SSM02
    appName: sensorApp
    appInstanceId: 1192
time: Feb 14, 2014 15:33:22 UTC offset=0 timeZone=GMT00:00
signature:   description=IP Fragment Too Small id=1206 version=S212 type=anomaly created=20030801
    subsigId: 0
    sigDetails: Too many small IP fragments in datagram
interfaceGroup: vs0
vlan: 0
participants:
    attacker:
      addr: 172.x.x.x locality=OUT
      port: 39715
    target:
      addr: x.x.x.x locality=OUT
      port: 514
      os:   idSource=unknown type=unknown relevance=relevant
alertDetails: InterfaceAttributes: context="single_vf" physical="Unknown" backplane="GigabitEthernet0/1" ;
riskRatingValue: 50 targetValueRating=medium attackRelevanceRating=relevant
threatRatingValue: 50
interface: GigabitEthernet0/1 context=single_vf physical=Unknown backplane=GigabitEthernet0/1
protocol: udp
Our next step is to make a service policy exception on the firewall itself. We are also considering reloading the IPS device or at least the analysis engine.
Thanks for all your help so far. Any more suggestions are most welcome. I'll keep you up to date.
Regards
Mariusz

Monitoring and Reporting on ACS 5.1 not working

Hello,
I have not managed to get the Monitoring to work on the ACS 5.1. This is an eval version. Advanced monitoring and reporting is installed on the ACS. This is my configuration on the Cisco Router
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 0 default start-stop group tacacs+
aaa accounting commands 1 default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa accounting connection default start-stop group tacacs+
logging origin-id ip
logging facility syslog
logging source-interface GigabitEthernet1/1
logging host 1.1.1.1 transport udp port 20514
logging monitor informational
epm logging
On the ACS, when I open the dashboard --> ACS health -> I get Status not available.
Global Instance under Logging Categories been configured for local logging
Thanks

The view logprocessor is not running
ACS role: PRIMARY
Process 'database'                  running
Process 'management'                running
Process 'runtime'                   running
Process 'adclient'                  running
Process 'view-database'             running
Process 'view-jobmanager'           running
Process 'view-alertmanager'         running
Process 'view-collector'            running
Process 'view-logprocessor'         not monitored
Does anyone know how to start it??
Thanks

SSRS 2008 R2 Calendar Control not working and report not refreshing on pressing enter in Chrome.

SSRS 2008 R2 Calendar Control not working and report not refreshing on pressing enter in Chrome.

SSRS reports are always best viewed in IE and the report result what you see in IE always will not be same and consistent in thirdy party browswers.
So consider using IE as workaround.
Also please refer:
https://social.msdn.microsoft.com/Forums/vstudio/en-US/2188de10-cff9-4e24-b14f-da5121f1c4a4/ssrs-calender-control-not-visible-in-chorme-on-server?forum=sqlreportingservices
Workaround here:
http://www.rajbandi.net/Fixing-SSRS-Report-Viewer-control-date-picker-in-Google-chrome/
-Vaibhav Chaudhari

My large monitor is not showing the screen of my MAC airbook on it. All cables are hooked up. I reset the pram and still not working. Message on black monitor says"check signal cable...?

My large monitor is not showing the screen of my MAC airbook on it. All cables are hooked up. I reset the pram per the instructions I received at the MAC store and the monitor is still not working. Message on blacked out monitor says"check signal cable". All cables are attached and monitor and MAC are both plugged into power source...Help ?

Go to System Preferences, Display. Click on dectect displays.

ASK THE EXPERTS - WAAS MONITORING AND REPORTING

Welcome to the Cisco Networking Professionals Ask the Expert conversation. This is an opportunity to learn about Cisco Wide Area Application Services monitoring and reporting with Michael Holloway and Joe Merrill. Michael is an escalation support engineer in the Application Delivery Business Unit focusing on escalations to engineering related to the Cisco Wide Area Application Services (WAAS) product. He has worked with Cisco WAAS since its initial development, and with the first product beta.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
Joe Merrill is an escalation support engineer in the Application Delivery Business Unit focusing on escalations to engineering related to the Cisco Wide Area Application Services (WAAS) product. He has worked with Cisco WAAS since its initial development, and with the first product beta.
Remember to use the rating system to let Michael and Joe know if you have received an adequate response.
Michael and Joe might not be able to answer each question due to the volume expected during this event. Our moderators will post many of the unanswered questions in other discussion forums shortly after the event. This event lasts through August 27, 2010. Visit this forum often to view responses to your questions and the questions of other community members.

Very good questions. Let me try and take them one at a time. Some of the answers you will likely find in the CM GUI help (upper-left corner is the Help button), or in the online documentation. But let's add a little more color and detail.
1)When we pull bandwidth Optimization report, on Y-Axis the graphs says Effective Capacity .What is Effective Capacity?
Basically, the "effective increased bandwidth capacity" is telling you how much additional WAN bandwidth you've gained because of the optimization. It will chart somewhere between 1 times and 100 times. Typically it charts all traffic, though you can configure it to chart traffic for specific Applications.
The CDM online help gives the formulas used to chart the graph:
Effective WAN Capacity = 1 / (1-% Reduction Excluding Pass-Through)
% Reduction Excluding Pass-Through = (Original Excluding Pass-Through - Optimized) / (Original Excluding Pass-Through)
2)what is reduction % excluding and including passthrough
Looking at the formulas given above might help you understand. The one is a reduction ratio compared to only the original traffic that is optimized. The other is a reduction ratio compared to all original traffic, whether it is optimized or not. So, if you want to know what kind of optimization you are getting for the traffic that you configured to have optimized, look at the "excluding pass-through" numbers. If you want to know the positive effect that optimization is having on your full traffic load, take a look at the "including pass-through" numbers.
3)What is effectivity capacity including and excluding passthrough ?
The effective capacity is what kind of throughput you can potentially realize on the WAN -- assuming you would fill it to 100% capacity -- because of the level of optimization you are seeing. The "including" numbers show you the effect of optimization compared to all the traffic passing through the WAE whether it is optimized or not. The "excluding" numbers show the effect of optimization compared only to the traffic that is receiving optimizations.
4)With the help of which report, we can show the customer that the file download which took 10 mins in first attempt, is downloaded in 10secons in next attempt?
This one is a little trickier. The reports are much broader than a single connection. They are for all traffic, or for traffic that matches specific defined Applications. You could create a separate Application and matching classifiers for the client and/or server IP addresses and/or ports, run the test, then configure the charts to only show you the data for that Application. By default, statistics for an Application aren’t charted unless you check the "Enable Statistics" box when defining/editing the Application.
5)How to show that the bandwidth utilization has decreased by which %.
You want to look at the % reduction numbers you asked about in #2 above.
6)Which report says that the applications have become this much time faster?
These questions are normally put forwarded by many customers ? Can you please help me with your expertise answer ?
This is probably the hardest question to answer.
"Faster" isn't always easy to define. You are probably talking about user experience rather than statistics found in a network device. What determines that experience? A web page fully populating with all the pictures? A CIFS-based application that saves a file? A custom application that collects data from different servers over different protocols to perform some operation? Much of that is subjective and based on multiple individual requests, sometimes over different protocols.
What we can provide are statistics to show the effect of WAN optimization and application acceleration for specific types of traffic. We can't show you that displaying a web page is N times faster with WAAS, because we don't know which of all the many HTTP requests that are made are specific to the user experience. But we can show that each of the requests received so much overall optimization, so much optimization from DRE, so much optimization from LZ, so much added benefit from HTTP acceleration.
What you would probably do is collect some base-line timings for performing certain user activities, then perform the same operations both cold (first pass) and warm (subsequent passes). Back up those timing numbers with reports from the CM GUI, and perhaps even the "show statistics connection connection-id ". Which reports to use? Start with those Optimization and Acceleration reports. Those are the reports we expect will give the most complete/accurate pictures of the benefit of WAAS. You can also create and even schedule custom reports as needed.

CDR report not working

Hi,
We have LYNC 2013 and Monitoring is enabled. the CDR report is not working. even User Activity summary for telconferencing and for audio, reports not working.
Kindly suggest troubleshooting steps.
Can we have any SQL query to fetch the report from database?
Thanks
jitender

Hi Raju,
From Monitoring server , CDR report is not working. Even "User Activity Report" not working and giving below error for "Telephony Conference" and as well for "A/V Conference"
" No results match the report filters. Change the filter values and submit the query again."
Thanks
jitender

Cisco ACS 5.2 (esx 4 vm) and Monitoring and Reports failure

I am evaling the Cisco ACS 5.2 Virtual Appliance on ESX4 and everything is working fine except for the "Monitoring and Reports" no matter what browser I try, it just keeps loading new tabs of the welcome screen, in the case of some browser versions it does this and does not stop.
I have tried the following browsers on Win7 Pro: IE 8, Firefox 4, Firefox 3, Chrome 12.
I have tried the following browsers on MacOS 10.6: FireFox 4, Safari 5.0.5
In Safari 5.0.5 it calls up one new window, but doesn't load anything in the right hand frame.
This is a fresh install, with an eval license. I am rather annoyed that it doesn't work out of the box, especially when there was not documentation that mentioned that anything needed to be setup for this to work after initial install, unless I missed something.
I installed the VM with the base 5.0.26 ISO and then applied patches 5.0.26-1 through 5.0.26-5.
Can anyone provide any help on this?

I am evaling the Cisco ACS 5.2 Virtual Appliance on ESX4 and everything is working fine except for the "Monitoring and Reports" no matter what browser I try, it just keeps loading new tabs of the welcome screen, in the case of some browser versions it does this and does not stop.
I have tried the following browsers on Win7 Pro: IE 8, Firefox 4, Firefox 3, Chrome 12.
I have tried the following browsers on MacOS 10.6: FireFox 4, Safari 5.0.5
In Safari 5.0.5 it calls up one new window, but doesn't load anything in the right hand frame.
This is a fresh install, with an eval license. I am rather annoyed that it doesn't work out of the box, especially when there was not documentation that mentioned that anything needed to be setup for this to work after initial install, unless I missed something.
I installed the VM with the base 5.0.26 ISO and then applied patches 5.0.26-1 through 5.0.26-5.
Can anyone provide any help on this?

Crystal report not working on 64 bit machine

Hello friends,
Hope everyone is doing good. I have an issue and you all are requested to help me out.
I have build an Application using VS 2008, i used Oracle 10g as database and Crystal report 2008 for reports. The Application and reports are working fine when i deploy it on 32 bit machine, but when I deploy it on a 64 bit machine, my Application works fine but reports are not displayed, when ever i run report it ask Db credential with the following message
"The report you requested requires further information."
then Server, user ID and password filed, I off course supplied credential but no results.
For resolving the issue i installed VS 2008 on 64 bit machine with redist CR Viewer and tried to verify database for the report thinking this might be an issue, but in CR designer it gives me following error when i tried to verify database or create new connection using OLEDB provider for Oracle
Crystal Reports ActiveX Designer
Logon failed.
Details: ADO Error Code: 0x
Source: Microsoft OLE DB Provider for Oracle
Description: Oracle client and networking components were not found. These components are supplied by Oracle Corporation and are part of the Oracle Version 7.3.3 or later client software installation.
Provider is unable to function until these components are installed.
OK
I tried the following fixes as well:
- Installed CR viewer for 64 bit machine
- Registering ORAOLEDB10.dll
- Reinstalling VS 2008
The Application works fine but Crystal reports are malfunctioning. Please help!!!!!!!!!!!!!!!
Thanks a ton in Advance
Happing coding and resolving issues
Danish Mustafa Khan

Also, see [this|https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/10d5fa88-2013-2c10-c9a5-f11963607d4e] article.
Ludek
Follow us on Twitter http://twitter.com/SAPCRNetSup

Event.hits property does not work at Adobe 9

I have just discovered that the property "event.hits" does not work at Adobe Reader 9 properly.
I have some JavaScript, which uses this property:
if (event.hits.length > 0)
var targetPos = event.hits[0].position;
Now, at Adobe Reader 9 the value of "event.hits[0].position" is not correct.
At Adobe 8 Standard this JavaScript works very well!
Can you comment this issue?

Hello to everyone!
There is a some PDF file, which works fine on Adobe 8 and does not work properly on Adobe 9.
You can download this file from the following hyper-link:
http://www.pdf3d.co.uk/pdf/box97.pdf
When I open this file on Adobe 8 then gold arrow works fine.
In this case the gold arrow (pointer) has a true location on the box.
When I open this file on Adobe 9 then gold arrow has a false location.
In this case the gold arrow (pointer) has a false location on the box.
Could somebody can to me a some suggestion?
Thank you,
Peter

Cisco Secure ACS 5.4/Monitoring and Report Viewer - SNMP Settings

Hello Everyone.
I hope this is the right forum for my question.
We just purchased 8 1121 ACS 5.4 appliances. I have some familiarity with the older 1113 and 1120 appliances running ACS 4.2. So I have a lot to learn.
Right now I'm trying to understand the Monitoring and Report Viewer System Configuration. I set the SNMP V2 read comm. string to the same string I configured from the CLI.
etc-labacsb1-1/admin# show runn | inc snmp
snmp-server contact "ACS1121;XXXXX"
snmp-server location "B1 Lab"
snmp-server community XXXXXX ro
1) It was not the same string as configured on CLI. Does setting this give me access to query more than system type or server type MIB objects.
2) Can you provide an example? (for example to query a switch - snmpwalk -v 1 -c XXXXXX hostname 1.3.6.1.4.1.9.9.43)
3) What is the MIB object tree OID (1.3.6.1.4.1.9.???) for these ACS appliances?
Thanks in advance.
Ray Westphal
EHI

that's correct. here is what we have in ACS 5.4 for snmp.
ACS 5.4 supports Simple Network Management Protocol (SNMP) to provide logging services. The SNMP agent provides read-only SNMPv1 and SNMPv2c support. The supported MIBs include:
•SNMPv2-MIB
•RFC1213-MIB (MIB II)
•IF-MIB
•IP-MIB
•TCP-MIB
•UDP-MIB
•CISCO-CDP-MIB
•ENTITY-MIB
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.4/device_support/sdt54.html#wp71020
~BR
Jatin Katyal
**Do rate helpful posts**

IMessage and FaceTime not working on Mac Pro and message stating to contact Support came on

iMessage and FaceTime not working on Mac Pro and a message stating to contact Support came on with a verification code. It was working on 8/29 but stopped on 8/30. When I called support to even speak with anyone they wanted $19. I don't want to pay $19 for an Apple problem. I cleared my key chain, also reset my apple ID password but still not working. Works fine on my iPhone.

There is no official public documentation of that error message as far as I know, but according to reports, it can mean (at least sometimes) that the same Apple ID is being used with the iTunes Store or one of the other Apple content stores, and the payment method is invalid. Sign in to the store and review your account. You do not, of course, have to provide any billing information to set up an account to use only with iMessage, as it's a free service.
Otherwise, do what the error message tells you to do. According to reports, you won't be charged for the call if you select "Apple ID" as the product you need support for, and cite the customer code in the alert as the "validation code" to the support representative.

PowerMac 5.1 drag and drop not working, any suggestions?

Powers Mid 2010 5.1 running 10.10.3, drag and drop not working smoothly, won't engage to drag. Any suggestions?

Thanks for the return, well, just trying to relocate a web screen or move a saved application from the desktop into a folder. I use Final Cut Pro Ten extensively and sometimes I want to drag something off my desktop into the time line on the FCPX. When I left click and hold on the item to drag it doesn't seem to engage then when it does move it quits along the way to the drop point. I hope that makes since too you? I use a Logitech two button with a scroll wheel wired mouse and have twin 32" monitors. Thanks Latranner

Timemachine and link not work property...

At home I have 10.4.2 and no digidesign hardware.
Timemachine and link not work property...
I send them: when I use ol algorythm- they caclulating 1 mono file (3 min lengh) about 15 min at dual G5. It is normal? And when I use new algorytm- nothign happen whith file. No result. (1 week it work fine).
Link in matrix not work
And what system I shood to use at studio whith PT?

CRash when change lengh of region whith new algoruthm
Date/Time: 2005-08-24 12:11:29.752 +0400
OS Version: 10.4.2 (Build 8C46)
Report Version: 3
Command: Logic Pro
Path: /Applications/Logic Pro.app/Contents/MacOS/Logic Pro
Parent: WindowServer [91]
Version: 7.1.0 (7.1.0(877))
Build Version: 1A73
Project Name: LogicPro710_ApplicationData
Source Version: 900001
PID: 288
Thread: 0
Exception: EXCBADACCESS (0x0001)
Codes: KERNPROTECTIONFAILURE (0x0002) at 0x0000007e
Thread 0 Crashed:
0 com.apple.logic.pro      0x0059a8c8 0x1000 + 5871816
1 com.apple.logic.pro      0x0037183c 0x1000 + 3606588
2 com.apple.logic.pro      0x00370000 0x1000 + 3600384
3 com.apple.logic.pro      0x002983b4 0x1000 + 2716596
4 com.apple.logic.pro      0x00298a84 0x1000 + 2718340
5 com.apple.logic.pro      0x00298c28 0x1000 + 2718760
6 com.apple.logic.pro      0x0005e264 0x1000 + 381540
7 com.apple.logic.pro      0x0005c6e0 0x1000 + 374496
8 com.apple.logic.pro      0x002aa538 0x1000 + 2790712
9 com.apple.logic.pro      0x00571e10 0x1000 + 5705232
10 com.apple.logic.pro      0x0016c090 0x1000 + 1486992
11 com.apple.logic.pro      0x0017864c 0x1000 + 1537612
12 com.apple.logic.pro      0x00178ad8 0x1000 + 1538776
13 com.apple.logic.pro      0x0016c150 0x1000 + 1487184
14 com.apple.logic.pro      0x0018e388 0x1000 + 1627016
15 com.apple.logic.pro      0x0018e588 0x1000 + 1627528
16 com.apple.logic.pro      0x0017d0cc 0x1000 + 1556684
17 com.apple.logic.pro      0x00124170 0x1000 + 1192304
18 com.apple.logic.pro      0x002fed40 0x1000 + 3136832
19 com.apple.logic.pro      0x003026a8 0x1000 + 3151528
20 com.apple.logic.pro      0x00300a94 0x1000 + 3144340
21 com.apple.HIToolbox      0x931229f4 DispatchEventToHandlers(EventTargetRec*, OpaqueEventRef*, HandlerCallRec*) + 692
22 com.apple.HIToolbox      0x9312214c SendEventToEventTargetInternal(OpaqueEventRef*, OpaqueEventTargetRef*, HandlerCallRec*) + 372
23 com.apple.HIToolbox      0x93128ed0 SendEventToEventTarget + 40
24 com.apple.HIToolbox      0x93229ffc SendEventFromMouseDown + 156
25 com.apple.HIToolbox      0x93205998 HandleClickInContent + 368
26 com.apple.HIToolbox      0x93155d6c HandleWindowEvent + 1584
27 com.apple.HIToolbox      0x931655c8 StandardWindowEventHandler + 160
28 com.apple.HIToolbox      0x931229f4 DispatchEventToHandlers(EventTargetRec*, OpaqueEventRef*, HandlerCallRec*) + 692
29 com.apple.HIToolbox      0x9312214c SendEventToEventTargetInternal(OpaqueEventRef*, OpaqueEventTargetRef*, HandlerCallRec*) + 372
30 com.apple.HIToolbox      0x93128ed0 SendEventToEventTarget + 40
31 com.apple.HIToolbox      0x93229ffc SendEventFromMouseDown + 156
32 com.apple.HIToolbox      0x931b6b08 HandleWindowClick + 572
33 com.apple.HIToolbox      0x931b6560 HandleMouseEvent + 456
34 com.apple.HIToolbox      0x931655bc StandardWindowEventHandler + 148
35 com.apple.HIToolbox      0x931229f4 DispatchEventToHandlers(EventTargetRec*, OpaqueEventRef*, HandlerCallRec*) + 692
36 com.apple.HIToolbox      0x9312214c SendEventToEventTargetInternal(OpaqueEventRef*, OpaqueEventTargetRef*, HandlerCallRec*) + 372
37 com.apple.HIToolbox      0x93128ed0 SendEventToEventTarget + 40
38 com.apple.HIToolbox      0x931b5530 HandleMouseEventForWindow(OpaqueWindowPtr*, OpaqueEventRef*, unsigned short) + 236
39 com.apple.HIToolbox      0x931b4aa8 HandleMouseEvent(OpaqueEventRef*) + 368
40 com.apple.HIToolbox      0x9312923c ToolboxEventDispatcherHandler(OpaqueEventHandlerCallRef*, OpaqueEventRef*, void*) + 496
41 com.apple.HIToolbox      0x93122c44 DispatchEventToHandlers(EventTargetR

Ultraslim wireless keyboard and mouse not working

Hi , I purchased the Lenovo Ultraslim Wireless Keyboard & Mouse (pn: 57Y4700) about 4 months ago for use with my T60 laptop (which i use with a docking station and large lenovo monitor at work).
Everything was woking fine until last Monday when I can into work after the weekend and neither the mouse or keyboard worked. I replaced the batteries in both, rebooted the machine several time, switch the USB ports for the nano receiver, but nothing seems to have worked.
I looked online for troubleshooting options, but did not find anything.
The mouse and keyboard don't seem to have a "sych" button - if I recall correctly everything worked right out of the box.
My theory is that the nano reciever was damaged (not sure how) -- but don't know how to proceed:
can the nano reciever be replaced;
any other options to troubleshoot;
any chance that this could be a software problem
Thanks

Hi coffee12345,
Welcome to the HP Forums!
I have read your post on your wireless keyboard and mouse not working with your desktop, and I would be happy to help you! To begin, I need to ask you a few introductory questions:
What is the Product and Model Number of your desktop?
What version of Windows are you using?
Is this a recent issue, or has it been like this since day one?
Are you using a USB hub to connect your peripherals or is it directly plugged into the computer?
Please re-post with the necessary information, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

IPS event monitor and reports not working

Similar Messages

Maybe you are looking for