Is there any limitation of firmware or hardware for QoS configuration (4400 controller & 1252 AP's)

Hi Experts,
Before proceeding for adding AP model 1131 and 1252 into my set-up , I need to know whether any limitation of firmware or hardware for QoS configuration in wireless set-up .
I have 4400 controller and 1130 & 1250 AP models.

Hi Vinod,
Since you have 4400 controllers, you can run upto WLC 7.0.x code. Refer this for more detail
http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
there is no specific limitation to 1131/1252 AP model as such, everything is WLC software dependent.
From later software 7.4.x,7.6.x,8.x, lots of improvement for QoS configuration & bandwidth control, but since your controller is old hardware, you cannot have those latest features.
here is a reference post on how QoS works in wireless environment
http://mrncciew.com/2012/11/28/understanding-wireless-qos-part-1/
HTH
Rasika
*** Pls rate all useful responses ****

Similar Messages

  • Are there any limitations for importing Apple Aperture Libraries for Lightroom 5.7 ? What can be the hardware limitation importing large Aperture Libraries like 200 gb ? Or is importing larger Aperture Libraries even possible at the moment for Lightroom 5

    Are there any limitations for importing Apple Aperture Libraries for Lightroom 5.7 ? What can be the hardware limitation for importing large Aperture Libraries like 200 gb ? Or is importing larger Aperture Libraries even possible at the moment to Lightroom 5.7 ?

    dj_paige wrote:
    As far as hardware restrictions, the only one I can think of is that you certainly need enough free space on your hard disk to accomodate the masters from your Aperture library.
    IIn which case, ensure all your masters are "referenced" in Aperture, and that you then go to Options in the Lightroom import box and import photos in their existing locations.

  • Is there any limitation of memory uses for apps in iPad2 or iPad3 ?

    Hi,
       Is there any limitation of memory uses for apps in ipad2 or ipad3 .For example an application can use 10% or 20% of available memory , is there anything like that or the apps can use the total available memory or like 90% of it ?
    I want to know about the memory distribution to the apps in ios .
    Would anyone suggest a right way ?
    Thanks

    iOS manages all memory. You should test your app in Instruments to be sure it is playing nice.
    See Advanced Memory Management Programming Guide

  • Is there any limitation of devices for purchased content?

    Hi there,
    Is there any limitation of devices i can download content i purchased on itunes store?
    For example if i bought a movie or and album, to how many devices maximum i can download this movie (of course with the same APPLE ID)
    Thank you in advance

    iOS manages all memory. You should test your app in Instruments to be sure it is playing nice.
    See Advanced Memory Management Programming Guide

  • Is there any limitation

    Is there any limitation to number of parameters to be passed to a procedure (when submitted using htp post )
    Thanks,
    NPR

    I believe Oracle has a imit of like 32k parameters, but there shouldn't be anything beyond that imposed by the way you're calling the procedure.
    Justin
    Distributed Database Consulting, Inc.
    http://www.ddbcinc.com/askDDBC

  • Is there any limitation on field size that can be defined in Idoc segments

    Hi all,
    I have extended a standard Idoc type and in my extended segment I have defined four fields GUID (char32), info1 (char255) , info2(char255) , info3(char255).
    This is a total of 797 bits which is well within EDIDD-sdata(char1000). But I am not able to put more than 132 characters in either info1, 2 or 3.
    Is there any limitation on this ?
    Regards
    Priyanka

    Hi Priyanka,
    I personally feel this error is not due to limitations but it might be due to the IDOC extension you had made and hence the default settings.
    Could you please try doing this -
    Note: Users require an authorization in order to carry out the procedure.
    The following correction is carried out with a fictitious attribute: 'info'.
    a) Call Transaction SE11.
    b) Enter the attribute name into the 'Domain' field, followed by '' (wildcard). For example: info
    c) The system displays the following hit list:
    info1
    info2
    info3
    d) Select the first domain and choose 'Change'
    e) Correct the number of characters. Forexample:
    Numberof characters   255
    f) Activate this domain
    Assign points in case this helps.
    Rgds
    Sum

  • Is there any limitations to the maximum number of dimensions in MP?

    hi all
    Is there any limitations to the maximum number of dimensions can be created in Multi provider. If so how what is the maximum number of dimensions that can be created in a multi provider?
    regds
    haritha

    Hi,
    Maximum number of dimensions 16. Out of 16, 3 are system defined
    1.Datapacket
    2.Time
    3.Unit
    It is restricted to 16 because the maximum no of dimensions in any database is 16.
    Reward points if helpful
    Cheers
    Raj

  • Is there any limitation of nested select.

    Is there any limitation of nested select.If yes please let me know.

    Hi,
    There are no practical limits to nested SELECTs, but as other repliers have already pointed out they quickly become a performance hog. I have stopped using them for years, and when I teach ABAP performance classes I also quote them as one of the top "don'ts". With nested selects, the number of calls to the DBMS can easily become enormous, putting the database server under stress.
    A good alternative - the one I favour most myself - is to use SELECT INTO TABLE for the"outer" select, followed by appropriate SELECT FOR ALL ENTRIES statements to handle the inner levels.
    ABAP joins are another alternative. When properly written, a join will be faster than a nested select. The problem is however that very often joins are not properly written. SELECT statements should always respect the KISS principle (keep it simple, stupid) and with a join it is very easy to violate that rule. A join over 2 tables should probably be OK, but with 3 or more tables you want to be very careful. If you really want to code a complex join, I recommend that you also code the same logic with different means (INTO TABLE/FOR ALL ENTRIES or even nested selects) and then compare that with the join. By the way: don't just compare the performance, also make sure that the two return the same data. You wouldn't be the first to code a really fast join which unfortunately returns incorrect results.

  • Are there any limitations in the Student Edition

    Hi,
    I just purchased the Student Adobe Creative Cloud. Are there any limitations? Also, can I put this on both of my personal computers, or just one? Thanks!

    Hi Anuj,
    You can install the application on 2 machines with 1 license.
    Regards,
    Sheena

  • Alert Rules vs Alert Category - Is there any limitations for multiple rules

    I have an alert configuration implemented already and i want to add few more rules for the same alert category.  While creating the rules for new set of scenarios, I am able to create only one rule . Is there any limitations for having the rules per category ?

    Hi,
    If the Suppress Multiple Alerts of This Rule checkbox is selected (default setting), then no further alerts are generated once the rule has been met until the first alert has been confirmed.
    There is no limitation of creating alert rule for a particular alert category.
    Check out the steps of Alert rule configuration.
    Creating Alert Rules
    To create an alert rule in which you use a defined alert category, proceed as follows:
           1.      Give the rule a name (Description).
           2.      Select the alert category that you want to use by clicking the corresponding category in the alert category table.
           3.      If necessary, specify conditions for the sender or receiver, or both.
    ○       If your rule results in alerts that must be assigned to a specific message, select the option Yes for the Bound to Message condition.
    ○       If your rule results in alerts that are not assigned to a message, that is, they are caused by errors that occurred before the message was sent, select the option No for the Bound to Message condition.
    In this case you cannot enter any further details about the sender or receiver.
    ○       If the rule is to cover both cases, select the Not Relevant option.
           4.      If required, restrict the errors further to:
    ○       Errors reported from the Integration Engine (with or without error category or error code)
    ○       Errors reported from the Adapter Engine (with or without adapter type)
    You can enter an asterisk (*) in steps 3 and 4. You can enter just the asterisk, or enter it at the start, end, or start and end of a string.
           5.      To add the new rule to the list of alert rules, choose Add Rule.
    If the Rule Activated check box is selected (default setting), the rule is automatically activated when you add it and is displayed as active.
    If the Suppress Multiple Alerts of This Rule checkbox is selected (default setting), then no further alerts are generated once the rule has been met until the first alert has been confirmed.
    Once you have created a rule, it is automatically displayed in the list of alert rules. If you want to display the conditions of a rule, select a rule in the list and choose Show Conditions.
    Hope this will help you.
    Regards
    Aashish Sinha
    PS : reward point if helpful

  • Is there any limitation to render smx tcode in portal

    hey is there any limitation to render smx tcode in portal . as a transaction iview.

    How about searching Arch wiki?
    http://wiki.archlinux.org/index.php/KDE#Fonts
    http://wiki.archlinux.org/index.php/Fonts

  • Is there any limitation in xtract structure,while doing enhancement.

    is there any limitation in xtract structure, while doing enhancement.

    Hello Satish
    There is no limitation as such defined by SAP but let me teel you one thing, if your extract structure contains a lot of enhancement than it s better you go for using two extractor and then use Multiprovider for viewing all the data....basically when you enhance structure you customer exits which slower down the performence....
    For example you have 0FI_GL_4 extructure and want to see the payment detail by some SD attributes like sales office divisoion..bla bla bla...if small enhancement is there you can include these field in 0FI_GL_4 extract structure but if it is significant than you should create another extractor for getting SD related data and merge them in BW side in Multiprovider
    Thanks
    Tripple k

  • Is there any way to set the default for *.doc document so that Pages opens them automatically?

    I have a number of Ms Word documents because I used to have Word for Mac before the last OS release.  Now, of course, when I double-click on them, I get a message saying that PowerPC isn't supported.
    Now Pages will open these files.  Is there any way to change the default for *.doc files so that a double-click will open them in Pages? 
    (Instead of me going to the trouble of finding out where they are actually located on the hard drive so that I can open pages and say - here, open this file--even though you didn't create it--)

    Click on a .doc file and type Cmnd I to open Get Info. In the Open with: menu select Pages, then click on Change All…
    Walt

  • Is there any way to create an installer for Mac OS and Linux OS once a stand alone application is created?

    Is there any way to create an installer for Mac OS and Linux OS once a stand alone application is created?  I have created an executable application that I want to distribute to Mac and Linux users (different applications were created in the respective OS).  I was wondering if there is any way to create an installer?  I think there probably isn't...  If the user were to simply download the Labview Run-time Engine from ni.com would they be able to run the application or is it more complicated than that?
    Thanks so much for your time.

    I think Shane tried to say, that it is on the Mac OS X installation DVD, NOT the LabVIEW for Mac OS X installation medium. And that could very well have changed in recent Mac OS X versions as well. They used to have Xcode on it too, but that seems gone as well.
    Rolf Kalbermatter
    CIT Engineering Netherlands
    a division of Test & Measurement Solutions

  • Is there any way to create a reminder for "today"?

    Is there any way to create a reminder for "today" in the new Reminders app? I used to be able to pull up the "today" list and add things that would go to my default list but automatically show up for today but now it looks as though that option is gone.  Additionally, any way to get dates/times to show up with reminders in the Notification Center?

    Hey chewie314,
    Thanks for the question. From the information you provided, it sounds like you might be looking for the "Scheduled" view. This view will show all of your reminders that are scheduled in a list. To access the schedule view, click the icon:
    Reminders - iPhone User Guide
    http://help.apple.com/iphone/7/#/iph88463e18
    Thanks,
    Matt M.

Maybe you are looking for

  • Error while add a stock to an item

    hi@all, here is a difficult problem i wasn't able to solve. I want to add a new stock to an item in the ItemMasterData at the StockData. After i added the Name of the stock to the table and i click on Update SBO shows me this Message: Another user-mo

  • Some thoughts on Previews

    To provide a little background on why I am thinking about how previews are used in Lr it might help to understand my workflow. I import my raw files, cull the ones I do not want to keep, keyword and add metadata, and tweak in develop. I then export t

  • Problem with update QuickTime player for OS X 10.5.8

    Hello everybody. I have Mac OS X 10.5.8 and today I couldn't open iTunes because as it was written in opened window my QuickTime has the old version (7.4). But there is no new version for OS X 10.5.8. What should I do? How to improve it?

  • Autodeploy of blazeds failure on weblogic11g

    Hi, I copied the blazeds.war, ds-console.war, and samples.war to the autodeploy directory and all three got this kind of error.  Weblogic 11g is really 10.3.4.  Does anyone have any clues.  This is a brand new weblogic installation with no other inst

  • Multiple tabs,sliders or pull-out trays in DPS

    Hello! How can I have multiple pull-out tabs in DPS on the same page. My screen shots show the tabs on the right and then the last tab pulled out. But it seems that this tab stops all the functionality of the other tabs, i.e. they dont pull out. Has