ISE Upgrade File Copy Error

Question

According to the Upgrade Guidelines for 1.2:
Copy the upgrade bundle to the local disk using the copy command from the Cisco ISE CLI: copyftp-filepath ise-upgradebundle-1.1.x-to-1.2.0.899.i386.tar.gz disk:/   Again, after you copy the upgrade bundle to the local disk, check to  ensure that the size of the upgrade bundle in your local disk is the  same as it is in the repository. Use the dir command to verify the size of the upgrade bundle in the local disk.
When I attempt to run this command, I keep getting the error:
"% long command detected at '^' marker"
using the following command:
" copy repository FTPDPZ ise-patchbundle-1.2.0.899-1-82500.x86_64.tar.gz"
I have also tried to replace the repository + name with an IP address, with just the repository name, and with 100 other things.
I tried to look up what a "long command" is, but I come up with nothing.
What is the proper verbage to utilize this command?

Answer 1

David,
It figures, doesn't it?  No worries.  The repository system is a confusing one, but it is what we have.  I have found detailed instructions on using it, but they are for the Cisco Prime LMS product.  The process is the same (I used these unstructions when doing my ISE 1.2 Upgrade), just substitute file names as necessary.
Step 1 Log into the shell and navigate to the location where the upgrade file, lms4_2_3_lnx_k9.zip is stored.
myhost/admin# shell
starting shell...
[myhost/ root-ade ~]
Note The  login name that appears in the command prompt depends on the login name  entered by the user while installing LMS on VM Console.
Step 2 Unzip the lms4_2_3_lnx_k9.zip file to extract Cisco_Prime_LAN_Management_Solution_4_2_3.tar.gz.
[myhost/ root-ade myloc] unzip lms4_2_2_lnx_k9.zip
Step 3 Copy the Cisco_Prime_LAN_Management_Solution_4_2_3.tar.gz to local disk partition of LMS 4.2.2 installed server (/localdisk).
Step 4 Log in with your credentials to the VM Console through Vsphere client.
Step 5 Create either a local or remote repository. A repository contains URL and credential details
myhost/admin# configure terminal
myhost/admin(config)# repository <>
myhost/admin(config-Repository)# url ?
  Enter repository URL, including server and path info (Max Size - 80)
cdrom:  Local CD-ROM drive (read only)
disk:   Local storage
ftp:    URL using a FTP server
http:   URL using a HTTP server (read only)
https:  URL using a HTTPS server (read only)
nfs:    URL using a NFS server
sftp:   URL using a SFTP server
tftp:   URL using a TFTP server
Step 6 Combine the URL to the repository that uses a local or remote storage.
a. The following IOS CLI shows how to combine the URL to a repository that uses a local storage:
myhost/admin(config-Repository)# url disk:
myhost/admin(config-Repository)# exit
myhost/admin(config)# exit
myhost/admin# write mem
Generating configuration...
myhost/admin#
b. The following IOS CLI shows how to combine the URL to a repository that uses an anonymous FTP server:
myhost/admin(config-Repository)# url ftp://<>
myhost/admin(config-Repository)# user <> password plain <>
myhost/admin(config-Repository)# exit
myhost/admin(config)# exit
myhost/admin# write mem
Generating configuration...
myhost/admin#
You can use the above mentioned steps for other protocols.
Step 7 Run the below command in the VM console in VSphere client.
myhost/admin# application upgrade Cisco_Prime_LAN_Management_Solution_4_2_3.tar.gz <>
Save the ADE-OS running configuration? (yes/no) [yes]?
Step 8 Press Enter to continue with LMS 4.2.3 upgrade.
An Application upgrade successful message appears.
Here is the doc that contains these instructions:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2.3/release/notes/lms4_2_3_release_notes.html#wp1183869