Issue for connecting iPad to Reflection in laptop via Cisco WLC

                   Hi guys,  recently we have purchased Reflection - an AirPlay mirroring software. Basically install Reflection in the laptop and you can view the screen of the iPad or iPhone via wireless network. we have tested in home wireless network no problem, but when connect to the cisco network, the iPad didn't recognize the REFLECTION installed in the laptop.
we are running WLC 5508,  WLAP AP-1331AG, 
we can ping from laptop to the iPad
laptop and ipad can access network without any issue.
there is no any application port has been blocked between the client via wifi
extra details for REFLECTION: http://www.reflectionapp.com/
would appreciate if you have any guestion or expereienced same issue and know the answer... Cheers.    Roy

hi all, thanks for the swift reply.   especially to Scott, the link is very usful, I have confgured the WLC according to the documentation, but problem still persists.
The Reflection is basically acting as Apple TV and in the home wireless network it works fine.
Connection method:    both Reflection installed in laptop and iPad is in same VLAN 38, which is wireless Vlan. both connected via wifi, I can ping each other,  so I don't think there is need to confgure the multicasting routing in the router.
The configuration in the WLC:
     1,  CONTROLLER -- GERNERNAL -- MULTICAST -- enable global multicast mode on  --  enable IGMP Snooping on.
     2, CONTROLLER -- GERNERNAL -- AP Multicast Mode - Multicast 239.0.0.0
     3, WLANs -- select the WLAN ID -- confgured the multicast interface
     4, Monitor  -- Multicast link -  displays following details.              
Group address
Vlan
MGID
224.0.0.251
38
1161
224.0.255.135
38
1160
239.255.255.250
38
1159
     5, I can also see the multicast packet broadcast from laptop to 224.0.0.251.  
I have read some of your guys discussion about issue with Bonjour, but my siuation is a bit different, both device are connecing via wifi, the REFLECTION is not connected to a switch.      Any advice? 

Similar Messages

  • Driver for connecting IPad with bluetooth to PC with Windows vista

    Where can I find a driver allowing me to connect My PC with My IPad by bluetooth?

    iPad, iPhones and iPod Touches cannot be connect to any mac or pc via bluetooth

  • Can an individual create a voice memo for free on their Windows based laptop via Apple website and then send it to perhaps an iCloud client?

    I am hard of hearing and will likely become deaf one day, so for me receiving voice memos (not telephone voice messages) on my iPhone is a nice treat!  Unfortunately not everybody has an Apple device.  Some of my family members and friends have tried to create a voice memo via Windows Media Player and sent it to my email, but as most know... I can't play the voice memos on my iPhone even after trying to use a conversion program to convert the voice memo. 
    So my question is... Can any individual (regardless of device they use) create a voice memo for free on the Apple website and sent it to an Apple client?
    i absolutely love my iPhone.  The accessibility options are wonderful to have for people who are deaf or hard of hearing.  But having this one accommodation done for the hard of hearing people specifically
    Thank you!
    Angèle

    cfr wrote:
    @lahwaacz,
    Could you point me to documentation regarding bugs/problems with laptop-mode tools? I'm using that right now and it has always worked pretty well but I'm currently seeing higher temperatures (~10C higher on average) and trying to figure out why.
    My fan operates continually but not, I think, very aggressively. But it has always done that so I assume it is normal for this laptop. (Have no idea really but it doesn't seem out of the way - it is a laptop, after all...)
    I don't know anything about fan control, my laptop controls fan speed automatically, I can't even get current fan speed.
    The main problem with laptop-mode-tools is that it's very huge, and the bigger the program is, the slower is the execution. Another problem is that it's connected to both battery and AC adapter ACPI events (see /etc/acpi/events/lm_{ac_adapter,battery}). On my laptop, those events are sent at the same time, resulting in running laptop-mode-tools twice. Most people once configure laptop-mode-tools to their liking and their hardware, so I think there is no need for such an extensive software like laptop-mode-tools, if something simpler does the same (or better) job.
    Also laptop-mode-tools can conflict with pm-utils (which are installed on many systems as dependency for some packages):
    https://wiki.archlinux.org/index.php/La … able_on_AC
    https://bbs.archlinux.org/viewtopic.php?id=106989

  • Logon issues when connecting to the R/3 system via System Template

    Hi All,
    I have created a System object for connecting to the R/3 system.
    the R/3 system is on ITS server.
    i have set the connector properties, ITS server details, User Management properties.
    Connector Porperties: Application Host: -
    , logical system name -
    , SAP client---,SID---, System number -
    server port-----,System type : sap_R3
    ITS server details : ITS host name, ITS path :/scripts/wgate, Protocal :http
    Usermanagement properties :    Logon method : SAPLogontickets, user mappingtype : Admin/user.
    Alias :Given the alias for the system created.
    i have also checked with the connection tests. The ITS Connection is green. but the connection test for the connector is red.
    Also the Portal user is not the same as the SAP backend user. So for this i have also made the user mapping, Under System Administration ---> Usermapping . ( we are using EP6.0)
    When i finally created a SAP trasaction iview based on the Alias. and tried to preview it. it is  showing me the error   "
    Name or password is incorrect, please reenter" .
    but in the preivew if i give the user id and password which i have mapped under the user mappings  it is entering the SAP trasaction.
    kindly suggest what can be the issue?
    Thanks & Regards,
    Kavitha

    Hi All,
    Thanks for all your replies. And sorry from my side for the late reply.
    I have followed all the suggestions made by every one of you.
    Also Arun, i have checked with the blogs that you have sent. All the settings done by me are exactly the same as defined in the blogs.
    but still the same error persists.  also When i tried to Login with the same user id as that of portal . It is working fine.
    Also while going through the blogs i have found that.. While doing the Connection tests. One of the test,  Connection test for the connectors is failed. i am unable to know the reason for failure.
    is this because of this reason, is the iview is asking for the re entering of user id and password ?
    kindly help.
    Also in most of the blogs i have found that for searching the  Message server. When we are not sure of name of the message server the  go to Transaction SMICM..... Where should this Tcode be entered. is it in the r/3?
    Thanks & regards,
    M.Kavitha harika.

  • HT204387 connect iphone 5s to windows laptop via bluetooth

    I am trying to connect my iPhone 5s to my Windows Laptop via Bluetooth.  The laptop can see the iPHone but cannot connect.  What can I do?

    Hello Rick,
    Congratulations on your new iPhone 5s!  To wirelessly sync your iPhone with iTunes, you need to be connected using a Wi-Fi network.  I found an article that has the steps outlined on how to sync your iPhone wirelessly with iTunes:
    Wi-Fi syncing
    Open iTunes
    To set up Wi-Fi syncing, connect your iOS device to your computer with the included USB cable. Select your device under Devices on the left-hand side.
    In the Summary tab, select "Sync with this [device] over Wi-Fi".
    Whenever the computer and the iOS device are on the same network, the iOS device will appear in iTunes, and you can sync it. The iOS device will sync automatically when all of the following are true:
    The iOS device is plugged in to power
    iTunes is open on the computer
    The iOS device and the computer are on the same Wi-Fi network
    While the iOS device appears in the left-hand column of iTunes, you can select the content tabs and configure sync options.
    Click Apply or Sync to sync the iOS device.
    You can find the full article here:
    iOS: Syncing with iTunes
    http://support.apple.com/kb/ht1386
    Thank you for posting in the Apple Support Communities.
    Best,
    Sheila M.

  • Impossible to connect iPad 3 to iMac 2008 via Bluetooth.

    Anyone out there getting annoyed with connecting iPad 3 to iMac 2008 using bluetooth ?
    iMac says the device is paired, iPad says "Not paired"
    Anyone to help me out ?

    Hi TOFFA_83,
    If you are having pairing issues with your iPad, you may find the following article helpful:
    iOS: Troubleshooting Bluetooth connections
    http://support.apple.com/kb/TS4562
    Regards,
    - Brenden

  • When connecting ipad to iPhones personal hotspot via wifi it is showin up as 2 connections when only 1 device is connected. Is someone hacking my phone?

    When connecting ipad to my iPhones personal hotspot via wifi it is showin up as 2 connections when only 1 device is connected. Is someone hacking my phone? I only figured out I had a problem when my partner did the exact same set up and it showed up as only 1 device connected. I have changed the password and turned it off/on and etc. the really weird thing is now when my ipad is turned off and I turn my iphone personal hotspot on it shows up with 1 connection (when I don't have anything connected) for about 5 secs and then goes off and then 1 device connected for about 5 secs and then back off. This just keeps going on and off. What is going on. Could my phone have a bug or be hacked. Please help as it is kinda freaking me out. Thanks.

    Hello asrt17,
    This may occur if your iPhone is connected to your computer via USB, as it will automatically share the connection via USB.
    iOS: Troubleshooting Personal Hotspot
    http://support.apple.com/kb/TS2756
    When Personal Hotspot is enabled, your iOS device automatically shares your Internet connection with your computer when connected using USB.
    Example: When you connect iPhone to your computer to charge or sync with iTunes. To avoid unnecessary data charges, turn off Personal Hotspot when not in use.
    Cheers,
    Allen

  • Has anyone had problems connecting iPad mini to Jawbone speakers via Bluetooth?

    Has anyone had problems connecting iPad mini to a Jawbone speaker system via Bluetooth?

    What versions BT are involved? Is AVD2P suppoted on both?

  • ITunes (64bit)  - freezes when checking updates for connected iPad

    Hello: I have the latest version of iTunes (same problem on previous versions). It's on a clean Win 7 64bit PC, i7, 8gb ram. If i connect a device it eventually brings up iTunes, goes into a sync and completes without error. If I then select my iPad in the left pane and click on the button to check for updates, iTunes freezes. I have waited many minutes and I get no response. Windows task manager does not show it as non-responsive. I end the task, start iTunes again and it works fine.
    This is a repeatable issue. Happened with previous two versions of iTunes too. I believe I uninstall-ed and reinstalled iTunes previously.
    I have Microsoft Security essentials and nothing else really unusual. It always works after I kill the task and try again!
    Any ideas?
    I have a MBP but to be honest, I am reluctant to use iTunes on it. The app seems bloated and troublesome.

    I guess iTunes for Windows is not supported... Time to remove it.

  • HT204266 Password issue for new iPad

    My apple password that works just fine on my MAC, will not work on my iPad.  When trying to purchase Aps, I keep getting an error message that the password is invalid.  I can't figure out what I'm doing wrong!

    make sure the account name or apple id does not have a typo in it.  mine did the first time, i mistakenly typed .net instead of .com   sign out of the account and retype the apple id and password from scratch.
    -mvimp

  • Can't connect ipad to Mountain Lion iMac via Internet sharing?

    Hello,
    I've always used Internet Sharing to create a wifi hotspot from my iMac, so that I can get an internet connection on my iPad.  After updating to Mountain Lion this does not seem to work.  Anyone know how?
    The hotspot generated by my iMac's internet sharing has never worked with my Kindle, but I would at least expect it to work with Apple's own products.  Hoepfully someone knows a solution?
    Thanks
    Bob

    Seems that the issue is something to do with connecting via WPA2. When I set Internet Sharing to use WEP (by option-clicking the security menu), I'm then able to see the network shares and the printer.

  • Connecting iPad 2 with Time capsule via speedport

    Hey guys!
    Can I connect my iPad 2 with my Time capsule which is connected to my Router (speedport)? I don't want to Switch the wifi Connection between Router and TC all the Time.
    I Hope you can help me with this!
    Regards

    Open the network preferences and make sure the ethernet is getting an IP from the TC.. you do not need to change any settings .. all you need is network connection.. if the ethernet is working just turn off airport for the time the backup is going on. Once you turn off airport in the MBP the connection will be forced to ethernet. You can do it more correctly by rearranging the order of preference for network connection.. but for now.. just turn off airport.

  • Unable to connect iPad to samsung galaxy s5 via hotspot?

    I'm able to connect the iPad to an iPhone with no problem.

        Let's see what's going on tellme! What error do you get when connecting to Galaxy S5? How far do you get when connecting?
    Thank you
    VanessaS_VZW
    Follow us on Twitter @VZWSupport

  • HT6114 This update broke my ability to connect a TV to my laptop via HDMI. Anyone else?

    Anyone else having the same problem? Is Apple aware of the problem? This is a big problem for me because I sometimes use the TV as my monitor for gaming and I also use this feature at work to send my screen to the projector when giving presentations. Can I roll back to 10.9.1?

    That's pretty much what fixed it zrfox. I hooked up the Vision:M to the computer so that it was listed in Device Manger. Right Clicked it's entry in Device Manager and Uninstalled it. I then unplugged it from the computer and waited a few seconds and plugged it back in and it was reinstalled correctly. It seems to be working OK now.
    I guess I'll have to wait for newer firmware or WMP Beta 2. :-)
    Thanks again for the replies everyone. Much Appreciated!

  • Unable to connect dell xps 802.11ac laptop to cisco 1250 AP?

    I have a new dell xps 15inc with the dell 802.11ac wireless card but it will not connect to the Cisco 1250 AP, however it connect to other APs just fine. I wondering if the Cisco 1250 AP is just to old and if there is any documentation proving this.
    Thanks ahead of time.

    On the dell wireless card, what happens if you force the card to use 802.11 a/b/g only and disable 802.11n/ac?

Maybe you are looking for

  • Missing titles on export or closing out project/reopening

    in FCPX everytime we export (either with the export in FCPX or sending to compressor) or close out project and reopen project -some of our titles go missing and  show up as back as the  default title or placement of our title gets moved back to defau

  • Case Statement with Group By

    Hello, I am trying to build a query that returns the 3 months of a quarter. Below are the two case statements that I am trying to use. I am getting a "Not a group by expression" in the first case statement, and a "nota a single-group group function i

  • PROBLEM in function module extractor

    Hi , i m facing a problem in creating a function module as extractor in srm but its not working plz letme know the way i can create the zfunction module as extrator. i created a datasource ZSRM_CS in which i m using BBP_PDS_CND as extraction structur

  • Source of supply for material

    Hi! Is it possible to have the supplier defaulted based on the inforecord when I enter a material number in the shopping cart? If possible, is there a difference between classic and extended classic in this case? Regards SF

  • IPhone browser won't open an inline PDF

    I receive notices from the federal court Pacer system (http://www.pacer.gov/) that include a single-use link to download a PDF of a given court filing.  On a computer, I am able to view and save the PDF.  But on my iPhone (and iPad) I can only see th