Itunes killed my ipod classic

itunes recently killed two classic 160gb ipods I have within a week of each other when the new version of itunes (10?) was released.  I received at different times the following errors
"can't connect to drive f:\"  error 
"the ipod cannot by synched. The desk can not be read or written to"  error
"the ipod cannot by synched. An unknown error occured (-124)" error
"the ipod cannot by synched. The required folder cannot be found" error
"disconnect  retry  cancel" error
My ipod began skipping songs, it would no longer sync and itunes would freeze when the ipods were connected to my computer.
My ipod shows that it is synchronizing when it is not (I had to set it to manual sync to avoid other errors).   then itunes doesn't run or respond within windows.  I eject the ipod. nothing happens.  I have to physically disconnect the ipod without ejecting in itunes to get itunes to run.
I've reset the ipods.  I put them in Disk Mode. I've connected them to other computers that have itunes 10.  Nothing works.  Nothing.  I've read every discussion group, loaded every driver.  Prayed to every saint. 
I use an old itunes version (8.0.2.20) because I prefer it to the newer versions that don't have the    Genre     Artist     Album    list categories along the top of itunes.  After declining yet another update, my two ipod classic (160 gb) would no longer synchronize, producing the errors above.   At the iPod store on Chestnut St in SF, I get a sneer and a shrug, and I am told I can get my (out of warranty) iPods repaired for $179 each + $59 for the one whose battery died when I (tried but failed to) manually load overnight the music I lost.
Apple ate $600 of my products and 60+ hours of my time.  May I please just sell them back my classic ipods and buy different MP3 players?  Apple is my least favorite consumer company in my history of buying products of any kind. 
Has anyone experienced similar synchronization errors using windows or a Lenovo T500 or itunes 8.0.2.20 with classic 160gb ipods?   If so, would you please recommend a solution to solving my synchronization problems?    Thanks in advance. 

rdf san francisco wrote:
My ipod shows that it is synchronizing when it is not (I had to set it to manual sync to avoid other errors). 
No such thing as "manual sync"! You either use Sync to synchronize your iPod with iTunes (look up synhronize - or synchronise in a dictionary) or you manually manage. If you have somehow managed to manually sync, that's probably why you're having problems.
rdf san francisco wrote:
 I eject the ipod. nothing happens.  I have to physically disconnect the ipod without ejecting in itunes to get itunes to run.
That's definitely not a good idea. If you physically disconnect an iPod (or other storage media) from your computer while the computer is talking to it, you will probably cause corrupted files on the iPod.
The best way to recover from "iPod won't eject" is to turn off the computer, then physically disconnect the iPod. (Once the computer is turned off, you know that it cannot be talking to the iPod.
rdf san francisco wrote:
I use an old itunes version (8.0.2.20) because I prefer it to the newer versions that don't have the    Genre     Artist     Album    list categories along the top of itunes. 
What?
That's simply not true!
Go (in iTunes) to and select View/Column Browser/Show Column Browser. If it is already showing or once you have it showing, go back into View/Column Browser and below the option to Hide Column Browser will be a menu for Artist, Album, Genre etc. Unfortunately, each one has to be selected one-at-a-time.
My advice to you is install the latest version of iTunes. Then try connecting your iPods to the new version and then get iTunes to check for and install the latest version of software (also known as the operating system or iOS) onto the iPod. Check each and every iPod. If iTunes tells you that the iPod needs a restore, make sure that's done with the latest iTunes.
If you are stuck at that point, post back into this thread again with precise information about what does or does not happen.
By the way - if you connect your iPod to a different iTunes, you run the risk of deleting everything off your iPod if you do not follow the prompts carefully. In addition, if that iTunes updates the operating system of the iPod, then almost certainly that iPod will no longer work with iTunes 8.

Similar Messages

  • Problem syncing itunes 12 with ipod classic on a PC

    Hi I just purchased a new Lenovo Yoga Pro 3 and installed the latest itunes 12 on it, but it won't sync with my ipod classic.  The itunes detects my ipod classic, but won't sync the music files and just ejects the ipod instead.  I have tried installing an older version of itunes onto my computer (version 11) but version 11 won't work on this laptop.  Please help!

    Unfortunately I cannot get the movies to play through Quicktime at all on the PC - the movie seems to play (timer runs and the little triagle moves), but all I get is a blank screen... The first time I tried to play one of the files, QT told me I may need to download additional codecs (although it did not indicate which one) - and directed me to the third-party codec download site. However, after downloading several of the different codecs, the .mov files still won't play through QT on the PC.
    Rule of Thumb: never download codec components arbitrarily. Since the files load into the QT Player, what you should have done was open the "Inspector" window and check the "Format:" entry to see which codec was used to compressed the video and then download the "correct" QT codec component and only the needed one.
    Is it not possible to get these files to play on a PC since they were imported and made on an iMac with iMovie?
    I would tend to suspect that you may be using an HDD or DVD camcorder here. Basically, the MOV file container is generic and can hold any valid combination of audio and video compression formats. DV would have imported as DV content. AVCHD or HDV would have imported as AIC/AIFF content which is normally supported intrinsically by QT. On the other hand, the content from MPEG2/AC3 based camcorders employs a special iMovie '08 import/conversion module which converts the AC3 to AIFF and the MPEG-2 "P-frames" and "B-frames" to "I-frames" which effectively turns the video into an M-JPEG track but leaves it labeled as MPEG-2 content which would likely confuse the QT Player. Further, if iLife '08 itself installs the playback component for this compression combination, you may not be able to locate/install a Windows version of this playback codec at all and may end up having to convert your DVD stored MOV files on an iLife '08 equipped Mac.

  • I have synced an audiobook purchased from iTunes onto my ipod classic but I cannot find it on my ipod.  Any suggestions?

    I have synced an audiobook purchased from iTunes onto my ipod classic but I cannot find it on my ipod.  I have looked in songs, artists, audiobooks, podcasts, etc., etc. with no luck.  Any suggestions?

    Hi mole02,
    Welcome to the Support Communities!  If you had issues with your movie rental, you can report it to the iTunes Store.  These folks can look at your billing account with you.
    Report a problem with an item purchased from the iTunes Store, App Store, Mac App Store, or iBooks Store - Apple Support
    http://support.apple.com/en-us/HT204084
    Learn how you can request help with an item purchased within the last 90 days.
    To report a problem or request assistance with an item purchased from the iTunes Store, App Store, Mac App Store, or iBooks Store:
    Visit reportaproblem.apple.com in your browser.
    When prompted, enter the Apple ID and password used to initiate the purchase of the item, then click Sign In.
    Find the item you're having a problem with, then click Report a Problem next to it.
    From the Choose Problem menu, choose the issue you're having.
    Follow the onscreen instructions. You might be asked to describe the problem in a text field.
    Click Submit, and we'll review your problem.
    If you use Family Sharing and you have a problem with a shared item, ask the family member who initiated the purchase to report the problem using the steps above.
    I hope this information helps ....
    - Judy

  • I need to know how to upload music to iTunes from my iPod Classic to my new mini Mac OS X version 10.9.2

    I need to know how to upload music to iTunes from my iPod Classic to my Mini Mac OS X Version 10.9.2.  Thanks in advance
    Miriam Parsons

    As soon as I posted the message I realised the download had failed to complete. Sorry, I'm so daft but thank you very much for your help :-)

  • Recently, I have been unable to import all of the "songs" or discs from multi-CD operas in itunes to my ipod classic or network hard drive. Only 1 or 2 discs import despite plenty of available space in both devices. Very frustrating! Any suggestions?

    Recently, I have been unable to import all of the "songs" or discs from multi-CD operas in itunes to my ipod classic or Seagate network hard drive. Only 1 or 2 discs or 20 or so "songs" out of a  total of 40 - 80 import despite plenty of available space in both devices. When I check itunes, each opera disc with all of the "songs" are listed. Very frustrating! Any suggestions?

    right click on the songs that do transfer and select create aac version then re sync
    Peace, Clyde

  • Why is it taking forever to transfer tunes from itunes to my ipod classic, I have over 6500 to copy and the current rate is 2 tunes per minute

    I am just copying tunes from itunes to my ipod classic, there are 6675 to copy and the present rate of transfer is 2 tunes per minute, which means that it will take over 55 hours at this rate,
    This has never happened before previously it took next to no time so what is happening?

    That show that your original library is damaged and needs to be repaired.  Apply the two fixes below in order as needed:
    Fix #1
    1 - launch iPhoto with the Command+Option keys held down and rebuild the library.
    2 - run Option #4 to rebuild the database.
    Fix #2
    Using iPhoto Library Manager  to Rebuild Your iPhoto Library
    1 - download iPhoto Library Manager and launch.
    2 - click on the Add Library button and select the library you want to add in the selection window..
    3 - Now that the library is listed in the left hand pane of iPLM, click on your library and go to the Library ➙ Rebuild Library menu option.
    4 - In the next  window name the new library and select the location you want it to be placed.
    5 - Click on the Create button.
    Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments but not books, calendars or slideshows. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.

  • I cant transfer from iTunes to my iPod classic. Whats going on?

    I have tried to transfer Star Trek into Darkness and Iron Man 3 from my itunes to my ipod classic. I have reset the ipod and updated itunes since maverick came out. Help.

    I called and asked them about it and Apple didn't know how to help me. They didn't know why it wasn't working.

  • HT1923 how do i sync itunes to my ipod classic with the newest version of itunes?

    how do i sync itunes to my ipod classic with the newest version of itunes?

    If you  have iTunes 11 turn on the Sidebar. Go to iTunes>View and click on Show Sidebar. You can also do a Crtl+S to show the sidebar.
    To sync to your iPod go to iTunes>Help>iTunes Help>Sync your iPod....>Sync You Device>Set up Syncing and follow the instructions.

  • Windows Vista, Itunes 10.7, ipod Classic, scan and fix message - why?

    I am trying to connect my wife's Ipod Classic to our Windows Vista computer.  I get a Scan and Fix Message for the Ipod from Windows.  I don't let it scan and click continue.  Itunes is frozen and won't recognize the ipod.  This has happened since upgrading to Itunes 10.7.  Also Itunes is choppy in playing all video content since upgrading to Itunes 10.7.
    I have checked system requirements and driver upgrades.  So far I have no fix.  One site recommended turning off WiFi sync for all devices in Itunes.  But of course the device must be connected, and mine won't connect.  All my itunes video is languishing.  :-(

    Wi-Fi sync won't apply since you have an iPod Classic and it doesn't contain any Wi-Fi hardware.
    To get rid of the Scan and Fix error, see this page: http://www.yourlocaltech.com/resolve-vista-scan-and-fix-error-when-plugging-in-i pod-or-other-devices/
    We'll start there for now.
    B-rock

  • HT1386 I can't get my iPod Classic to sync with iTunes.  My iPod Classic is up to date, and i have downloaded the latest version of iTunes.  When trying to sync, it gives the message "The iPod "Brad D's iPod" cannot be synced because it cannot be found."

    Do I have to un-install and re-install iTunes or do I have to restore my iPod Classic (I don't want to lose everything in my music library)?

    Clicking sounds from an iPod that has a hard drive for storage is not a good thing.  It usually means the hard drive is faulty.  That is the likely reason for getting an error during the attempt to Restore.
    If you use a Mac, you can try putting the iPod into Disk Mode
    http://support.apple.com/kb/ht1363
    If it goes into Disk Mode, connect the iPod and instead of running iTunes, run Disk Utility.  Does the iPod appear in the Disk Utility sidebar?  If it does, select the iPod device in the sidebar, not the volume indented below the device (if there is one).  Go to the Erase tab.  Set the Format to Mac OS Extended (Journaled).  Name does not matter.  Click on Security Options and choose to write a single pass of zeros over the entire disk.  This serves as a good "stress test" for the iPod's hard drive.  Back on the main window, click Erase.
    This takes longer than a regular erase, but you should see steady progress.  If it errors out, or stalls for a LONG time (like hours), the hard drive is likely to be faulty.
    If it completes successfully, quit Disk Utility, run iTunes and try to do another Restore

  • My iPhone 4 isn't recognized by iTunes, but my iPod classic is.  How do I resolve this?

    I was able to sync my iPod classic to iTunes no problem.  I have not updated my phone in a very long time untilo yesterday.  I also have not synced/backed it up since March.
    I followed the instructions here:
    http://support.apple.com/kb/ts1538
    iTunes is update, I uninstalled/reinstalled 3 times today.
    My phone has the newest iOS on it.
    My USB cable and port are fine, as I just synced my iPod on it.
    My phone charges, the bottom port is fine.
    I've restated my phone numerous times.
    I have tried the MSCONFIG onstructions.
    I am unable to use another computer for this.  I can actually go into iTunes, add file to library, and add photos that way.  So, it's recognized by my computer.  However, iTunes won't reconize it to sync.  Any help would be appreciated.

    Hello Lawrence,
    I do have AppleMobileDeviceService.exe running.
    My USBs are plugging in straight into the laptop.  All 4 work.  Just today, I synced my iPod with multiple USB ports.  It works for the iPod, but the iPhone won't pop-up.  The iPhone does not appear in iTunes as a button anywhere.
    I am unable to use another computer for this.  I can actually go into iTunes, add file to library, and add photos that way.  So, it's recognized by my computer.
    This should have been seperated.  Basically, I don't have another computer accessible to me to back-up sync on iTunes with.
    The last part means in iTunes, I can click "File > Add file to library" and the iPhone is shown as a camera icon.  I can click on it and have access to photos.  I can add those photos to the iTunes library.  That's about as far as the connectivity goes with the iPhone right now.

  • Itunes not recognising ipod classic

    Hi all, if your using a Black iPod classic 160GB with wheel on the front when using and connecting to iTunes, if iTunes does not recognise your iPod you will need to  reload iTunes from Apple site, don't let any one tell you it is possible to uninstall iTunes THIS IS NOT POSSIBLE !!!!!! !!!! Even the people on the chat site could not tell me this. You will just need to reload over your existing iTunes, then when the system asks you, restore your iPod back to factory settings, don't fear as you won't loose anything! It will then take a while to copy everything back onto iPod, like a software update for iPod.I went through this experience and spent hours trying to uninstall etc until I got onto a very helpful guy in The States called Noble. So thanks. Good luck.

    I've seen a few other posts from people having issues with Playlists not being correctly synced with various models of iPod, but as yet, I've not seen a solution.
    I guess we'll just have to wait for Apple to fix it in an iTunes update. I think it's an iTunes issue rather than a Classic issue, and I'm sure Apple already know about it, but if you feel like it, you could send them some feedback at: http://www.apple.com/feedback/itunesapp.html or for the Classic at http://www.apple.com/feedback/ipod.html. Interestingly, the iTunes feedback has no option for "bug report". Make of that what you will!
    Note that Apple do read the feedback, but they will not respond to you.

  • After iTunes 10 upgrade iPod Classic not identified nor can I restore

    Totally lost and don't know how to proceed. I have been using iTunes with my iPhone with never a problem. I received an iPod classic 160GB for Christmas last year and again, no problems, everything has been working great.
    I am using Windows 7 Ultimate 64bit. I upgraded to iTunes 10 and iTunes works great. I plugged in my iPhone 2G, no problem. I plugged in my iPod Classic 160GB and iTunes freezes, NOTHING happens at all. The album cover pictures don't even display until after I unplug the iPod Classic device.
    I can see iPod device in "My Computer" but not in iTunes 10. In iTunes 10 the device doesn't appear at all until I give up and unplug the device. Then an error message pops up and the iPod is shown in the left column. The error says a file is missing and the device can't sync. I can't do anything except click OK. Then the error message goes away and the device drops out of the left column.
    I searched for info on this problem, and have tried all of the suggestions.
    It charges through USB with no problem except the battery is fully charged.
    I tried 3 different USB ports on the PC.
    Tried restarting iTunes.
    Tried restarting the computer.
    Went to Apple support website, tried the troubleshooting assistant:
    *Reset the iPod.
    *Had already tried different USB ports.
    *Had already tried restarting the PC.
    *Removed iTunes 10 and all the software programs in the order specified.
    *Went to Apple website and Re-installed iTunes.
    *ITunes and iPhone still work fine, NO iPod Classic recognition in iTunes.
    *Next option is to Restore but CAN'T because iTunes won't recognize the iPod to perform Restore. After reading the instructions, it appears that the iPod has to be connected to do this, and that's the problem -won't connect!
    Is there anyone who can help? This didn'thappen until installed iTunes 10.
    The iPod has 120GB of music on the device. The device is still working fine. I just can't get iTunes 10 to recognize the iPod Classic device.

    After upgrading to iTunes 10, when I tried to connect my 80GB iPod Classic to my Mac Book Pro, the iPod was not recognized by either my computer or by iTunes. It would say "Connecting" on the iPod, but then it would click and show the Apple icon for a few seconds, then the cycle would repeat.
    I finally decided to start the iPod in Disk Mode and then connect to my computer. When I did that, it would connect to my iTunes and I was able to sync.
    I then went to Disk Utility and verified and repaired my iPod disk (no problems and nothing to repair.) On one discussion, the person then erased everything from his iPod and then restored. Rather than do that, I disconnected my iPod and re-connected it in the standard mode. This time, it was recognized by iTunes and I was able to sync.
    Tried it again this morning and again it was able to sync. The next time, it may not, but right now it appears that might be a possible solution.

  • ITunes not recognizing iPod Classic

    Ok, so this post is going to be a little long since I need to explain what is happening with my iPod Classic 160gb.
    I noticed a few days ago that songs were 'disappearing' on my iPod when I would listen to it through iTunes on my computer (When I say disappearing an exclamation mark would appear between the song number and the song title in iTunes-- when I would try to start the song iTunes would automatically skip to the next song-- acting as if the song wasn't there). I disconnected the iPod after I was done listening, shut down the computer and turned off my iPod.
    The next day I started up my computer and plugged in my iPod. Windows came up and said that it recommended a disk scan. I ok'd the scan. Afterwards, all of the songs had disappeared off my iPod and now iTunes doesn't recognize my iPod. Windows recognizes the iPod-- itunes does not.
    **As a side note, in the iPod menu, in settings, the window on the right hand side of the screen show about 37GB of free memory. This was about how much was left with all my music on the iPod. However, if you go into any other menu, eg songs/artist/playlist it says there is no music/artist/playlists.
    I've gone through all of the troubleshooting steps listed for the iPod classic and windows 7. iTunes is still not recognizing the iPod. I've also tried on another computer-- stil no luck.
    I understand that the classic cannot be reset without iTunes (this is a stroke of brilliance on Apple's part). What can be done if after all of the troubleshooting steps iTunes STILL does not recognize my iPod? Has this iPod given up the ghost?
    Thanks, Mike

    Hello there,
    I would first start with this article assuming you are running Windows. Be sure to attempt each and every possible troubleshooting procedure as needed to try and resolve the issue.
    [iPod appears in Windows but not in iTunes|http://support.apple.com/kb/ts1363]
    B-rock

  • Itunes freezing when Ipod Classic plugged in

    When I plug in my ipod classic 80 gb,itunes freezes (cannot click or play anything) and an error message shows up.
    "There is a problem with this drive. Scan the dvice now to fix". Tried that and it doesn't work. It also says my ipod is not responding.
    The newest version of itunes is installed and our computer is windows 8.
    Any suggestions would be greatly appreciated. I have looked at lots of other discussions but nothing has helped my problem.
    Thanks!

    I have the same problem: if I load iTunes for a second time and my iPod is plugged in the iTunes app and the system menus (top right corner of screen) freeze up.
    Unplugging and plugging in the iPod seems un-freeze everything for me.

Maybe you are looking for

  • Firefox will not start after upgrade from 3.0.1

    I have Firefox 3.0.1. I would like to upgrade to 3.6, but if I try to upgrade to any version, I cannot open Firefox. It is not like the other "Will not start" problems, because in the Task Manager, firefox.exe pops up, then goes away instantly. I hav

  • Tried to replace RAM but now computer not starting...PowerMac G5 dual 2.0 - are my hard drives safe? What's up?

    Hello - I tried to increase the RAM in my old and trusted Power Mac G5 (dual 2.0...2005)  tonight and now I'm in trouble. It has only 4 slots for RAM.  It came installed with 2X256 and 2X512 ram cards.  I bought 2X 1GB of Ram from Crucial.com after s

  • Canon IR c1028 - USB and Mac issues

    I have a Canon IR c1028: http://www.usa.canon.com/cusa/support/office/color_imagerunner_copiers/color_imagerunner_c1030_c1031... I have it USB attached and Network attached. The network attached prinitng works fine but one of my home compouters is ha

  • Idoc problem while loading

    Hi Gurus, I am getting error "<b>Idocs missing: No end-confirmation arrived in the Warehouse from</b>" while loading data from R3 to BW via process chain. Can any one please suggest me how solve this problem. Thanks in advance. Regards Tony

  • When I log in the Portal using Administrator user, I can use it correctly.

    I have created a Room IView. When I log in the Portal using Administrator user, I can use it correctly. However when I am using another user, I get this error message:  com.sap.portal.pcm.Title Portal Runtime Error An exception occurred while process