Itunes not showing Ipod

I have a 20 gig ipod that has worked fine for six months. last week when i connectedn it to my laptop via usb, a message came up and said i had to restore my ipod(and it wouldn't show up on itunes). tried to restore it but had another error "ipod service error". I followed everything in ipod support. uninstalled and reinstalled ituned. I'm able to restore the ipod now and windows does recognize it but itunes does not.I installed my original itunes as well as the current version. I've also installed itunes on both hard drives and used different usb ports.
help?

I've been suffering this problem too so I hope this is useful......
Tried to run restore, but wouldn't recognise iPod. Tried also to reformat but I couldn't access it in Windows Explorer, but I could see it as a removable disk, just not access it.
Have just managed to fix it as follows:
- Connected iPOD, with switch in off position.
Amber light starts flashing, Becomes visible but not accessible in Win Explorer.
- Right click on MyComputer and select Manage
- Select Storage, Disk Management
You should now see a removable disk, perhaps as a Drive E: or similar.
You hopefully can select this disk, and it is pretty unlikely that the file type will not be shown (normally would show FAT32, or NTFS).
- From the menu bar. Actions > All Tasks > Format.
- Reformat the disk as FAT32 as Deqqie says.
This hopefully should allow you to see this disk in Win Explorer which is progress.
- You should now be able to see the device using iPod updater and run a Restore.
This then had me all back to normal and working in iTunes
Good luck!

Similar Messages

  • ITunes not showing iPod as connected

    I have been trying to sync my iPod for several hours, but iTunes isn't showing that any devices are connected.
    I have tried every USB port on my computer, and am getting the same result. I also checked the 'My Computer' section of the computer and it does not show anything connected.
    And, if it helps, I have a Second Generation iPod Nano.
      Windows XP  

    If your computer meets all minimum system requirements, and you've done all the listed troubleshooting steps in the article, then you should go ahead and set up a dispatch for the iPod. You can do that at the following website.
    http://depot.info.apple.com/ipod/

  • Windows does not show ipod as a removable drive

    my itunes recognises my ipod and works properly, but windows does not show ipod on "my computer". can i use it also as a hard drive? and how do i make windows see it as such?

    Hello Rea Meir,
    And welcome to Apple Discussions!
    Make sure the *Enable Disk Use* option is enabled for your iPod under it's Summary tab in iTunes. For more help and information, see this Apple support document.
    [Using your iPod as a storage drive|http://support.apple.com/kb/ht1478]
    B-rock

  • HT201270 ITunes not Showing iPad and iPhone after IOS7 upgrade.

    ITunes not Showing iPad and iPhone after IOS7 upgrade. I have reinstalled iTuned. Repaired services...etc

    Hey Sliqueg,
    There are a few troubleshooting articles that can help resolve the issue. Check them out here:
    For Windows:
    iPhone, iPad, or iPod touch: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    For Mac OS X:
    iPhone, iPad, iPod touch: Device not recognized in iTunes for Mac OS X
    http://support.apple.com/kb/TS1591
    Sincerely,
    Delgadoh

  • Add PDF to iTunes not showing up in print PDF pop up menu

    Add PDF to iTunes not showing up in print PDF pop up menu. I lost the print PDF to iTunes option. its no longer there. I still have web reciets and mail. also when i add in "edit menu" they don't get added.all this used to work fine

    i found the answear. go to library/PDF Services  or  ~/Library/PDF/Services and clean out this folder. you can also add scripts and automator scripts to add things

  • Why does the iTunes not show "Photos"

    Why does the new iTunes not show "Photos" after it is synced, and why does iCloud not show Photos also?

    Ralph9430 offers a good suggestion.  But you may need to do this before taking his advice:
    Check in iPhoto's Preferences (which you can open from the iPhoto menu).  Look in General, and make sure "Connecting Camera Opens" is set to "Image Capture").
    If it is set to "iPhoto", you won't be able to get to Image Capture easily.

  • ITunes not showing songs that are on the iPod Touch

    I have an iPod Touch 4th Generation.
    I use iTunes 11.0.
    I usually connect my iPod Touch to iTunes and play songs from there because I do not put songs in my itunes library.
    I was doing this as usual and today when I connected my iPod Touch to iTunes, songs did not show up on the music tab of "On This iPod".
    Just the previous day, I opened iTunes and there were all my songs.
    Today, iTunes does not show any of my downloaded songs that were not bought from the iTunes Store.
    The iTunes Capacity Bar shows that I have songs on my iPod Touch.
    But when clicking on the iPod and going under the music tab in "On This iPod", there is no music other than a few songs, which were purchased from the iTunes Store itself.
    I also tried third party software just today to check if I can get the songs off my iPod.
    I tried using SharePod and it did not detect any songs, not even the purchased songs from iTunes.
    There are songs on the iPod Touch only. I can play all the songs from the iPod Touch just fine.
    They are simply just not showing up on iTunes.
    How do I get iTunes to show the songs on my iPod Touch? The capacity bar says there are songs.
    I tried SharePod a few times long before this happened, and it showed the songs on the iPod Touch.
    I don't understand why all of a sudden the songs all disappeared from iTunes itself only.
    (I would say this is similar to other issues where iTunes DOES show songs while the iPod itself DOES NOT. Mine is the opposite.)
    Thank you for the help in advance.
    Message was edited by: j_leongg
    I tried backing up the iPod Touch.
    Now all the songs on the iPod Touch (except for the purchased ones) are turned to blank names and are skipped.
    There is no name for each song or artwork, they all are called 'unknown'.
    Only the purchased songs are left unharmed. Everything else is corrupted now.

    SOLUTION: Some Music Won't Play After Upgrading Your iPhone To iOS7
    Red square in red circle cannot play songs
    My iPod isn't playing certain songs. Help?

  • IPod Classic no music, freezing iTunes, not showing up, HELP????

    I have a used iPod Classic 120GB. I bought it off my friend. I took it home and added my files (about 5,000 songs and 13 videos) to his stuff (about 6,000 songs) and ended up with it being about half full. I let it sync, then ejected and disconnected. But it said there was nothing on it. I went back and reconnected it to my iTunes. The iTunes froze, and I couldnt access the iPod in anyway. I disconnected it, and when I did it unfroze everything, and popped up in iTunes, saying that the iPod was missing.
    I checked the iPod's "About" section and it said that it had 56GB of "Other". I took it back to my friend and he said he deleted the folder with everything in it. It is empty now except for 1.2 GB of who knows what, but still freezing my system and not showing up.
    I have tried restarting it, and putting it into disk mode. Nothing worked.
    HELP
    Version: 2.0.1 PC
    Message was edited by: black-belt-boy

    jartis wrote:
    HI, i am having the same issue with my ipod. Can you please tell me what you mean by putting on "disk mode" and deleting the files? Thanks
    First let's make sure the drive is physically OK...
    *Check your iPod with Diagnostics Mode*
    It's possible that your iPod's hard drive has started to fail. Take your iPod and place your right thumb on the centre SELECT button and your left on the top MENU button. Press down both thumbs for about 6 seconds until your iPod reboots. Immediately move your left thumb around to the rewind button |<< on the left and hold this down together with SELECT for a further 6 seconds. Your iPod should now switch into Diagnostic Boot mode. Press MENU for *Manual Test*, then select *IO > HardDrive > HDSMARTData* to reveal your stats. For comparison here are mine for my 2 year old 6th Generation Classic:
    Retracts: 889
    Reallocs: 12
    Pending Sectors: 0
    PowerOn Hours: 2202
    Start/Stops: 894
    Temp: Current 24c
    Temp: Min 10c
    Temp: Max 50c
    Take a note of your results. When finished press *SELECT & MENU* for 6 seconds to reset the iPod again.
    With modern disc drives sectors are no longer marked bad by a disc scan, if the SMART firmware detects a sector it has trouble accessing it will attempt to invisibly reallocate it to a spare area of the disc.
    Note that I've only 12 remapped sectors and none pending. To help explain what the numbers mean here is an extract from the Wikipedia S.M.A.R.T. article:
    *Reallocated Sectors Count*
    Count of reallocated sectors. When the hard drive finds a read/write/verification error, it marks this sector as "reallocated" and transfers data to a special reserved area (spare area). This process is also known as remapping, and "reallocated" sectors are called remaps. This is why, on modern hard disks, "bad blocks" cannot be found while testing the surface – all bad blocks are hidden in reallocated sectors. However, as the number of reallocated sectors increases, the read/write speed tends to decrease. The raw value normally represents a count of the number of bad sectors that have been found and remapped. Thus, the higher the attribute value, the more sectors the drive has had to reallocate.
    *Pending sector count*
    Number of "unstable" sectors (waiting to be remapped, because of read errors). If an unstable sector is subsequently written or read successfully, this value is decreased and the sector is not remapped. Read errors on a sector will not remap the sector (since it might be readable later); instead, the drive firmware remembers that the sector needs to be remapped, and remaps it the next time it's written.
    Large numbers of Reallocs or Pending Sectors would suggest your drive is failing and that you may need to repair or replace your iPod. Check your stats after another attempt to update your iPod. If the numbers increase that again points to hard drive failure. While it won't be good news at least you'll know it isn't some random software problem and you can decide what to do next.
    <hr>
    Assuming you've ruled out a physical problem with the iPod's drive we can now move on to check for logical problems...
    *Check iPod hard-drive for errors*
    Hold Select+Menu on the iPod for about 6 seconds until it resets, then hold Select+Play as soon as the Apple logo appears, again for about 6 seconds to put the machine in disk mode. Open iTunes and in the Sync tab of the preferences menu check *Disable automatic syncing of all iPhones & iPods*. Now connect your iPod to the computer, wait until it connects, then close iTunes. Browse *My Computer* and right-click on the drive for the iPod, click Properties, then click Tools. Under Error-checking, click *Check Now*. Under Check disk options, select *Scan for and attempt recovery of bad sectors* (Optional - takes ages but a good idea if you've reason to suspect physical damage). Click Start. Mac users should run *Disk Utility / Repair Disk* for the equivalent process. This should find and correct any errors in the logical & physical structures of your iPod's hard drive. Once these have been fixed you can reset the iPod (hold Menu+Select ) and should stand a better chance of a successful restore. It might also pay to check the status of the source drive containing your media, particularly if no errors were found on the iPod.
    And if that still doesn't help try Erase your iPod - The Super Fix for most iPod Problems. Basically a low level format of the iPod’s hard drive to get around whatever problems are stopping iTunes from restoring it.
    Once you've restored your iPod don't rush to dump all the data back exactly as it was before. I have found that lots of large or complex smart playlists can sometimes trigger constant reboots or dumping of the iPod's library. In addition, larger transfers can fail leaving data in an inconsistent state. Try this technique for populating the iPod in stages.
    *Break up large transfers*
    In iTunes select the menu item *File... New Smart Playlist*. Change the first drop-down box to Playlist, the next to is and the next to Music. Tick against *Limit to*, type in say 10, then change the drop-down to GB, and set the last drop-down to artist. When you click OK you can enter a name for the playlist, e.g. Transfer. Now sync this playlist to your iPod rather than your entire library. When the sync is complete modify the rule ( *File... Edit playlist* ) to increase the size by your chosen amount, then sync and repeat. You can experiment with different size increments, if it doesn't work just choose something a bit smaller until it works each time. Before long you should have all your music on your iPod. Once that's done you can move on to other media such as podcasts, videos, photos, playlists etc.
    tt2

  • HELP- video bought on itunes not showing up in ipod

    i bought the first part of a two part episode of monk off itunes today and, for some reason, part one is not showing up on my ipod. part two is on there and you can play it and it works just fine and everything, but for some reason part one does not show up on there at all. is there some reason why this is so?

    Try manually draging the video to your ipod. If it is on your ipod delete it and transfer it back onto your ipod. Try resetting your ipod by holding the middle button and the menu button for 10 seconds. Also try checking your ipod video settings to make sure that the settings are the way you want it.

  • Itunes does not shows ipod touch

    hi everyone i have ipod 4thgeneration and it does not show up on itunes........

    keeferaf, note that the article you cited does not apply to iOS devices like the iPod touch. It applies to:
    Products Affected
    iPod, iPod mini, iPod nano, iPod shuffle, iTunes 10 for Windows, Windows

  • ITunes will not show ipod!!!!! tried everything as suggested!

    Hello, bought a new 4gb nano and after installing everyting as instruction suggest, nothing works. Windows shows ipod, but itunes does not. I see I'm not the only one with this problem, but what else can be done, is there anyone to talk to?(phone)? I didnt know that i needed a degree from MIT to use this. six hours of trying and 250 spent, dont know if this is worth it or not!
      Windows XP  

    Hi bfos,
    Have you seen this post:
    iPod Shows Up in Windows but not iTunes
    good luck,
    maz

  • I deleted all my artwork but it shows up on itunes NOT my ipod

    Well I had followed this person's idea to add artwork BUT instead it DELETED ALL MY ARTWORK! BUT its still on itunes, but doesnt show up on my ipod..anyone know how to help? PLEASE
    "I had the same problem and was getting the unhelpful error message "Unknown Error occurred (-50)", but I was able to fix my artwork. I believe this problem occurs when you manually manage your IPOD library (at least that is my situation) and your Itunes library and your Ipod library don't match. Here are the steps I took to fix the problem:
    - First in Itunes go to Edit > Preferences > Ipod Tab > Music Tab and make sure that the "Manually Manage Song and Playlists" button is selected.
    - Next make sure that checkbox for "Display Album Artwork..." is unchecked. Click Ok.
    - Go back to the main Itunes screen and make sure your IPOD library is selected and then hit CTRL-A to select all of the songs.
    -Next right click on the highlighted songs and select "uncheck selection"
    -Now go back to Ipod preferences and check the "Display Album Artwork" check box and click ok.
    Once I did this Itunes was able to optimize all of the artwork on my Ipod without throwing the "Unknown Error occurred (-50)". All of my artwork now displays when I disconnect the Ipod from my computer.
    I believe that when songs are checked in both Itunes and the Ipod, Itunes somehow attempts to synchronize the artwork between the two. Removing the check marks in the Ipod removes this synchronization requirement.
    Hope this helps."-someone else on dicussions board
    Sony Vaio   Windows XP  

    Restore the phone.

  • Playlists from iTunes not showing up in Playlists category of iPod

    When I drag playlists from iTunes onto my iPod they do not display as Playlists on the iPod. I make every album into a playlist in iTunes (and make my own custom playlists), and I drag these onto the iPod. On the iPod I can browse Artists and Albums, but not my predefined Playlists.
    Is there a setting to select to view my Playlists on the iPod?

    Hi Andrew,
    Well, go access playlists on your iPod, you go to "Music", and select "Playlists", which is at the top of the list.
    Do you see "Playlists" at the top of that Music menu, or not?
    -Kylene

  • Windows XP or iTunes not recognising ipod

    I see a lot of posts regarding ipods not being recognised by either Windows and/or iTunes and I just thought that I would pass on this tip that has helped me fix this problem on two Windows PCs.
    In both cases the cause of the problem was usb related. For some reason Windows sometimes gets its underwear in a twist with its usb configuration and in both cases the following procedure fixed the problem.
    1.Turn off the computer.
    2.Unplug all USB devices from their connections in the computer except for keyboard and mouse.
    3.Turn on the computer.
    4.Plug devices back into the computer or hubs, one at a time in the following order. Wait for Windows to find and enable each device before connecting the next.
    a Hubs
    b Printers and multifunction devices
    c Scanners
    d External drives (not memory or key plugins)
    e Camera and PDA docking stations
    f All other devices
    5. Make sure the devices work.
    That's it.
    I know it sounds like alchemy and i'm not suggesting that it will work for everyone with ipod recognition problems but it has certainly worked for me with two PCs. My PC and iTunes happily run 3 ipods - a shuffle,an ipod mini and an ipod nano.
    I thought the above might just help some harrassed Dads and Mums from tearing their hair out on Christmas morning.
    lowdown
    Compaq   Windows XP   P4

    Do either of these help?
    iPod missing in "My Computer" or in iTunes for Windows
    iPod shows up in Windows but not in iTunes
    Is the software up to date?
    iTunes
    iPod Updater
    Updating iPod's Software
    Also, if you have a 4G iPod, why post in the iPod nano forums?
    btabz

  • ITune not recognising iPod touch, on and off.

    Okay, this is not the usual iTunes not recognising the iPod.
    I had this problem when I first set up my iPod. After a full uninstall and reinstall of iTunes, as described in the support article, my iPod was recognised. Now I have added more music to my collection, and a couple of the apps need updating I wanted to update my iPod. I connected my iPod and nothing, it does not show in iTunes. It is showing in my computer as a camers which I really wish it would stop doing. Also when my iPod was connected the first time I set up to allow it to wirelessly update and it won't do that either.
    I am stuck on what else to do. I just hope I am not going to have to do a full uninstall and reinstall every time I want to update my iPod, because it rather defeats the purpose.
    I have read and followed the instructions here:
    http://www.apple.com/support/ipodtouch/assistant/itunes/
    I have even de-authorised and re-authorised my account as suggested at the Apple store. It is the latest model of touch, not sure what gen that is but it is only two weeks old. What else can I do to try and get this sorted?

    Illass thank you for the reply, but as I said I have done everything on the support page. I even printed off the uninstall instructions as it gave you a rather precise order to do it in and I did check for the folders to see if they had been left, I learnt that when I updated my graphics drivers and still a game said my card wasn't up to scratch, even though my card supported shading 4.0 it only needed 2.0 for the game.
    I also printed off the software conflict information otherwise I would have gotten totally lost.
    However thank you for the disabling info, as it was getting a tad annoying when I was connecting it to charge up.
    I decided to uninstall and reinstall again and low and behold it is recognised again. That makes it the second time I have had to do this to get my touch recognised. However doing this everytime I want to update is going to be rather annoying.
    Ah the days of the Nano 2nd gen, and the innoence of those times. Shame some clumsy so-an-so knocked it out of my hand and stepped on it as it was just so simple to use.

Maybe you are looking for

  • ITunes 8.2 Apple Mobile Device Support does not install

    I am unable to complete the full 8.2 install on my machine - the AMDS component fails to install, although the rest of the packages go in successfully. Unfortunately, without AMDS, I can't sync' my iPhone 3G, nor my iPod. Having broken out the AMDS p

  • How can i show the dialog of certificates when tring to sign (like CAPICOM)

    Hi, I'm using "Windows-MY","SunMSCAPI" to choose a certificate from the keystore to sign a document. 1) Can i show a dialog containing the certificates in the key store like in CAPICOM? 2) To find a solution i 've found this code (CAPICOM + JAVA) her

  • Apple account identity confirmation email

    Dear Customer, Some information on your account appears to be missing or incorrect. Please update your information promptly so that you can continue to enjoy all the benefits of your Apple account. If you don't update your information within 72 hours

  • Call list in ICWC and SAPGUI

    hi, does anyone know why i can't seem to "view" the call list assignments in IC web? but it it can be viewed in SAPGUI? I have created the call list and its assignments in the portal. When i log into the ICweb, i click n the Call List link, all i see

  • Deafult values features not working in CATS

    Mates I have maintained 315 inftyp for a pernr and when i try to enter the values for the same pernr in time sheet using cat2 ,it doesnt default the sender cost centre and activity type.Infact i  have flagged under cost assignmetn variant Asssignment