Jabber Voicemail Incorrect Time Stamp

I just noticed the the time stamp on my voicemails in Jabber v9.0.1 Build 12296 have the incorrect time stamp. They are all one hour behind. I confirmed that this does not happen in any of the following:
Jabber v9.0.5
CUPC v8.6
Jabber for Mac v8.6.1
Is this happening to anyone else?

did you get this sorted out?  Im having the same problem with Jabber v9.1.5, CUC 9.1.2 and cucm 9.1.2.  Both cuc and cucm use the same NTP time source.  Time looks fine on the handsets and from the cli..

Similar Messages

  • Mail delivery problems and incorrect time stamps

    I'm running Server 10.4.9 and along with hosting two webpages I am hosting email for one of the domains. Whenever a message is received by an account hosted by my server, the time listed for receiving the email is incorrect. It varies from 1 to 4 hours fast or slow depending on the source of the email. It happens with both incoming and outgoing mail. If a message is sent from one account to another on my server, the time stamp is correct.
    In addition to the incorrect time, I have noticed messages directed to one account being delivered to another. For example, in my own mailbox I recieve messages that were intented to go to another user mailbox on my server. I don't know if that is related to the same problem or if it is a spam issue but I figure any bit of information will be helpful.
    And finally, I do not believe all mail is reaching the intended mailbox. I have junkmail and notjunkmail accounts enabled for spam and if I redirect 10 emails usually only 5 at the most will make it. I get no return errors when redirecting (ex: undeliverable)
    I have checked the obvious time and date panels in OS X including the server admin and everything matches. The timezone is also correct. I type date into the terminal and that comes up correct as well. This isn't my first time configuring a server.... I've hosted mail servers with 10.2 and 10.3 in the past with no problems but this is my first time using 10.4. I'm pretty comfortable navigating through the server, but I have limited experience in terminal. (Just for FYI) Usually with enough time I can figure almost anything out, but I've run out of ideas here. Any help would be greatly appreciated. Thanks...

    I'm running Server 10.4.9 and along with hosting two
    webpages I am hosting email for one of the domains.
    Whenever a message is received by an account hosted
    by my server, the time listed for receiving the
    email is incorrect. It varies from 1 to 4 hours
    fast or slow depending on the source of the email.
    Where are you looking at the timestamp? On the message headers? Are you taking into account any timezone corrections on same headers? E.g. following message sent from Apple HQ to UK...
    Received: from uk2mxserver3-10.uk2.net ... Sun, 15 Apr 2007 10:24:34 +0100 (BST)
    Received: from bz3.apple.com ... Sun, 15 Apr 2007 10:24:31 +0100
    Received: from acutil03.apple.com ... Sun, 15 Apr 2007 02:24:22 -0700 (PDT)
    Otherwise you will need to post examples.
    In addition to the incorrect time, I have noticed
    messages directed to one account being delivered to
    another. For example, in my own mailbox I recieve
    messages that were intented to go to another user
    mailbox on my server. I don't know if that is
    related to the same problem or if it is a spam issue
    but I figure any bit of information will be helpful.
    And finally, I do not believe all mail is reaching
    the intended mailbox. I have junkmail and
    notjunkmail accounts enabled for spam and if I
    redirect 10 emails usually only 5 at the most will
    make it. I get no return errors when redirecting
    (ex: undeliverable)
    What does the mail.log show for these messages? You should be able to track them moving through the system.
    -david

  • Incorrect time stamps

    The time stamps on my saved files are not correct. They give the time in the time zone where I was previously and where I last restarted the computer. Is this the expected behaviour? The time displayed at top right of the menu bar IS correct - it changed as expected when I changed the time zone in system preferences - but all the time stamps on files modified, created, and opened since changing zone are incorrect.
    I'm guessing (hoping) that when I restart all will be well, but in the meantime would like to know if this behaviour is expected.

    Thanks jimocallaghan. I'm (literally) half a world away from my install disk right now, but could try your suggestion on returning home in a few weeks time.
    In the meantime I've restarted and, lo, the incorrect timestamps which were being generated after my zone change are now magically corrected. i.e not only are new time stamps being applied correctly but the files which were wrongly stamped now carry the correct stamps.
    Has anyone else found that, after a time zone change, a restart is required to ensure that timestamps are applied correctly ?

  • VOICE MEMOS and Wrong Time Stamps in Itunes

    I've noticed that my voice memos in the new iTunes 11.1.3 (8) have incorrect time stamps all over them now. This is a real problem for me, since I need the dates that the messages were recorded. I just tested this out by recording a new one today (2/11/14) on my new Iphone 5s. It showed up dated 8/13/12 2:13pm. My phone has the correct date on it, so what gives?
    Any solutions out there?
    Not to mention the fact that there are NUMEROUS DUPLICATES of previous memos that have become weird artifacts in my iTunes library each time I've backed up my materials. AND the new iTunes setup makes it incredibly hard to *actually remove data* from my system. I am concerned my private material is no longer private, but being archived elsewhere for meta-data purposes.
    C'mon, Apple. You're really slipping.

    I see all timezones, have you tried setting the time/date manually? I'd do than, then pop an email to support.
    Norwegian and a BB/PB user. Read what I mean, not what I spell.

  • Time stamp does not update automatically

    Hi, All. I want include the time stamp (yyyy-mo-dd-min-sec) in the file name. However, the value of the time stamp does not update automatically/synchronizes with the computer clock at each new run. I need to do it manually with the right click and update the time to the current.
    How can I solve this? Thanks a lot in advance.

    What does this have to do with NI counter/timer hardware?
    What language are you using and what function are you using to get a timestamp? If the language is LabVIEW, then all you need is Get Date/Time in Seconds. If you are using a front panel Time Stamp control, then you are using the incorrect function.

  • Format Time Stamp String for excel error

    Hi all,
    I am currently trying to format the time stamp from labview to excel, in an excel recognizable format.  Ive attached a photo of that part of the vi.  The time stamp is formated correctly when it leaves the format time stamp block and after it leaves the build array block, but when it is written to excel file it is formated in what looks like a standard format and excel does not recognize this as a time stamp.
    Any ideas to fix the issue?
    Thanks
    Attachments:
    Time stamp.PNG ‏7 KB

    The Example Finder has a few ActiveX examples I think one uses Excel.
    Also if you have the Report Generation Toolkit I think this is what you need
    http://digital.ni.com/public.nsf/allkb/38D7104644E0F7A5862578B1001A86C5
    It sets the cell format to be how you want.  The default for a timestamp is "m/d/yyyy h:mm".
    BUT I just think I have an easier solution.  The problem is it correctly detects that this is a time stamp, but the cell format is incorrect.  If we convince it that it is a string it will look right and I assume that's all that matters.  So add a space to the front of your time, so have the format be " %Y-%m-%d %H:%M:%S" (notice the space) and I think it will look the way you want because Excel thinks it is a string.
    Unofficial Forum Rules and Guidelines - Hooovahh - LabVIEW Overlord
    If 10 out of 10 experts in any field say something is bad, you should probably take their opinion seriously.

  • DataSource  has to be replicated (time stamp, see long text)

    Hi Experts,
    in Production i am getting an error  like below
    DataSource  has to be replicated (time stamp, see long text)
    @5C@     Errors in source system     @35@
    Message no. R3016
    Diagnosis
    DataSource 8ZCRFAC03 does not have the same status as the source system in the Business Information Warehouse.
    The time stamp in the source system is 19.04.2011 12:56:44.
    The time stamp in the BW system is 19.04.2011 12:29:02.
    System Response
    The load process has been terminated.
    Procedure
    Copy the DataSource again and then activate the transfer rules that belong to it. You have to activate the transfer rules in every case, even if they are still active after the DataSource has been copied.
    i replicated data source and activated transfer rules giving source system and infosource but still it is failing with same message
    what went wrong  not able to understand
    Please help,
    Thanks in Advance
    Nitya

    Seems to be an incorrect transport sequence:
    1. First transport you DS from source system R/3 QA to R/3 Prd
    2. Once it is successfully transported to R/3 PRD, Replicate DS in BI PRD
    4. Now try to collect your infosource, DS, TR in transport request & try to transport it from BI QA to BI PRD.
    5. Once it is successfully replicated in Production try Running the loads
    It should work.
    Regards
    Raj

  • I am having trouble reading a time stamp on a video using OCR

    I am trying to read a time stamp that is overlaid on a video, using OCR software, but it will not read it correctly I've tried the OCR Preproccessing and Recognition Config VI's and neither have been able to correct to problem I would appreciate some help

    In my experience, it is very important that the contrast not only be
    very good but also that the characters can be easily distinguished
    from the background and that the characters are generally repeatable
    and unique. I've had problems with characters "smearing" into the
    background so that the OCR can't tell where the background ends and
    the character begins.
    Beyond the standard NI OCR stuff, you can use a database to map
    incorrect whole words to correct whole ones in OCR but this only works
    when there is a set of unique words that are significantly different
    from each other. It doesn't work on numbers since any number is
    generally as likely as any other.
    It may be worthwhile to invest in higher quality acquisition equipment
    to improve the image quality. If your video source itself is poor
    quality, then it won't matter though.
    Douglas De Clue
    [email protected]
    nestor wrote in message news:<[email protected]>...
    > Ernest,
    >
    > As "labviewguru" mentioned a screenshot will help a lot to determine
    > if the problem is the image quality. However if you can't post this
    > image then please review the following links I'm attaching here. They
    > talk about OCR and most important, about Filtering, which is mostly
    > used in Vision for image enhancement, noise reduction, sharpen an
    > image, etc. Please review the links mentioned below and apply some
    > filtering techniques to your image. This may help a lot, personally
    > I've used OCR software and I have required in most cases to apply
    > filtering before running the OCR functions.
    >
    >
    > href="http://zone.ni.com/devzone/conceptd.nsf/webmain/E69D110920B99E838625685E0081B881?opendocumen...
    >
    > href="http://zone.ni.com/devzone/devzone.nsf/webcategories/605B55C3100D02188625685E0076C928?opendo...
    >
    > href="http://zone.ni.com/devzone/devzone.nsf/webcategories/E28E087D201C1AD48625685E00824E3C?opendo...
    >
    > Here at the Developer Zone, inside the Development Library you will
    > find in the Vision chapter a lot of information that will be helpful
    > for your development. Please review it. In case you require further
    > assistance you can keep posting questions here at the Discussion Forum
    > or give us a call/email (www.ni.com/ask).
    >
    > Good luck!
    >
    > Nestor Sanchez
    > IMAQ/Motion Support
    > National Instruments

  • I'm in the U.K. but my icloud emails are U.S. time stamped, how can I change this?

    I'm in the U.K. but my icloud emails are U.S. time stamped, how can I change this?

    Hi foxie-d,
    Welcome to the Support Communities!
    The article below may be able to help you with this.
    iCloud: If email shows the wrong time
    http://support.apple.com/kb/PH2644
    When you send or receive email, the time it was sent or received appears in the email header (the information at the top of the email). If the time shown in your email header is incorrect, you need to change the time zone setting for your iCloud account.
    Change the time zone on iCloud.com
    Click your account name, then choose Account Settings.
    Click Time Zone, then click a time zone on the map.
    You can also click the time zone name below the map, then choose a time zone from the pop-up menu.
    Click Done.
    You need to log out of iCloud, then log back in to see the changed time zone in iCloud Mail.
    Happy New Year!
    - Judy

  • Appending and add time stamp at a time........

    Hi all,
    i am working on a scenario...
    it is file based..no mapping and bpm can be used.
    I need to pick up file through xi and append it and put in the target with time stamp to it.
    we can achieve this if mapping or bpm is allowed.....
    But,in file processing we can use only one option at a time.....
    I found a way:
    scenario one: files will be appened and kept in a temparory folder
    using another scenario we will pick up the appeneded file and add time stamp and keep in target structure...
    but i dont think this is advisable...
    please suggest me any other ways to achieve this...(can run operating system command be helpfull??)
    thanks in advance..
    Regards,
    Kiran.

    HI,
    Yes you are right, Appending and adding Time Stamp will not be possible simultaneously.
    Refer - this could help you
    Dynamic Filename with TimeStamp  
    Dynamic Filename with TimeStamp
    /people/william.li/blog/2006/04/18/dynamic-configuration-of-some-communication-channel-parameters-using-message-mapping
    But some how you have to use mapping for it. Then if its allowed to use the mapping then as you have suggested, should have to go for two scenarios. No alternative,
    Probably also you can try with Customized Adapter Module for this.
    Thanks
    swarup

  • Changing time stamp format in the file receiver adapter file name

    Hi all,
    How can we change the standard date time stamp from
    filename_yyyymmdd-hhmmss-mil
    to
    filename_yymmdd_hhmmss
    i.e.,  I want "underscores" instead of "hyphens" and also I do not want the MilliSeconds.
    I read in the forums that I have to use the combination of variable substitution and mapping functions to do this, but not sure how exactly.
    Can the experts help me with this please?
    Many thanks.

    Hello Ramesh,
         You can make this possible using runtime filename creation using UDF.
    Please go though the below steps.
    Message mapping:  
    Create an UDF and include the piece of code that captures the Filename and Timestamp from source side via ASMA.
    Modify them according to our requirement by adding the <Timestamp> at the end of <filename> with _.
    Map the UDF to any of the top level node so that the modified filename will be available for the target communication channel
    UDF Code is:
    try {
    String filename    = "";
    String timestamp = "";
    DynamicConfiguration conf1 = (DynamicConfiguration) container
        .getTransformationParameters()
        .get(StreamTransformationConstants.DYNAMIC_CONFIGURATION);
    DynamicConfigurationKey key1 = DynamicConfigurationKey.create( "http:/"+"/sap.com/xi/XI/System/File","FileName");
    DynamicConfigurationKey key2 = DynamicConfigurationKey.create( "http:/"+"/sap.com/xi/XI/System/File","SourceFileTimestamp");
    filename = conf1.get(key1);
    timestamp = conf1.get(key2);
    filename = filenametimestamp".xml";
    filename = filename.replaceAll( "-" ,"_" );
    conf1.put(key1,filename);
    return filename;
    catch(Exception e)
         String exception = e.toString();
          return exception;
    Click on Advanced tab and check the Option u201CSetAdapterSpecificMessageAttributesu201D in addition to that check the attribute that are required to be captured during run time. In our case File Name and Source File Time Stamp are required to be checked
    In the receiver communication channel Mention u2018 * u2018as File Name Scheme.
    Click on Advanced tab and check the Option u201CSetAdapterSpecificMessageAttributesu201D in addition to that check the attribute u201CFile Nameu201D which will carry the modified value in the UDF .
    i hope this will help you.
    Monica

  • Transfer time stamp from text file into MS Access thru Labview

    Hello everyone,
    I am Cruz; Long time listener, First time caller.
    I am currently monotoring data being collected by an oven. The data is stored in a text file. I am using Labview to take the data from the textfile and place it in an MS access DB for manipulation. The first three columns of the text file are the time stamp of data. When i transfer the data into Access i cant get the first three columns to display as a time stamp. Can have some pointers on what how to get the first three columns to display correctly.
    Additional info:
    the text file is a 1D array that gets overitten with every new mesurement tanken. the transfer to Acces is to not loos any of the information and to better manipulate the data into forms and such.
    Running Labview 2010
    attached is code and text file.
    Any help is greatly appreciated.
    Attachments:
    Oven test other.vi ‏16 KB
    datalog032010003.txt ‏1 KB

    Your first mistake is reading the file as DBL. Your first three columns are obviously not numeric values. Did you ever look at the output array? Read it as strings. Second, you would need to combine those first three columns to create an actual time stamp before you write to the db. Unless of course you have one column for date, one column for time, and one column for AM/PM. I would not recomend that type of structure in the db.

  • Bug report: Time stamp misalignment in recent list

    Bug report: With the new compact design, go to recent pivot, tap on a conversation, press back button to go back to recent, notice the time stamps to the right of the list have moved even more right, with text being cut off the screen.
    Using Lumia 1020 with Cyan and 8.1.1 DP.

    I figured this would be the best place to post it so that an Apple representative might see it.
    Actually it's not as likely to be seen here since there are so many posts for any Apple rep to have to scan. The best way to report an issue to Apple is through the feedback pages or, if you're a member of Apple's developer program, through the bug reporter.
    Regards.

  • "The movie contains an incorrect time value" error - saving a trimmed video

    I am attempting to trim a video shot on my Samsung CL65. The video was shot in High Quality HD 1280 x 720. I open the video in QuickTime and then use the Trim command to remove the last part of the video and then close it to Save it. When I save it I get the following error: "The document SAM_0306.MP4 could not be saved as "SAM_0306". The movie contains an incorrect time value." I think this has to do with an encoding error in the original file or in the trimmed file but I have no idea how to get around it.
    Any ideas?

    This info probably won't help with your problem, but it's information for others who get this error.
    It's probably the software that made the MP4. ffmpegX, for example, and the mencoder program inside it, do this with every H264 encoding when the video is longer than 1 hour. Time codes are correct up to 1 hour, then the seconds value gets wacky (3600 is added to it). Quicktime won't save a movie with a time code like 1:20:3623.120 (although it will correctly display 1:20:23 in the player).
    Apple used to offer quicktime scripts that would allow you to see what the time code in a stream really looked like. Applescript appears to have officially and quietly gone missing, though, and those scripts are no longer available online as far as I can tell. There were some really handy other scripts that would allow you to view all sorts of movie properties and manipulate tracks (great for syncing poorly synced sound, for example), but time code problems like the above would invariably mean the movie couldn't be saved.

  • Select-options for time stamp

    Any ideas on which data element to be used for select-options for timestamp on the screen so that a user is able to f4 help too.
    i am using data element 'tzntstmps' but i am not getting f4 help for it.

    Hello Trivenn
    I do not think it makes sense to search for any other timestamp data element which might be part of a search help.
    TZNTSTMPS = UTC Time Stamp in Short Form (YYYYMMDDhhmmss)
    How could such a search help look like? A calendar control combined with some kind of "time control"?
    You may facilitate the entry of time stamps in such a way that if the user enters only a date in the LOW field (e.g. 20080422 without time) you change it AT SELECTION-SCREEN (PBO of your selection screen to 20080422000000).
    Correspondingly, you change a date value (e.g. 20080422) at the HIGH field into 20080422235959).
    If, however, the user enters already a complete timestamp you do not change anything.
    Regards
      Uwe

Maybe you are looking for

  • How can I transfer pictures from my PC to my Android?

    I'd like to see if I can xfer pics from my pc to my phone. I connected it to pc w/usb cable but after it updated the phone software the icon disappeared from the Device list in the "My Computer" window.

  • PDF Printtemplate in BI 7.0?

    Hi all, in http://help.sap.com/saphelp_nw70/helpdata/en/44/85de4943af5919e10000000a1553f7/content.htm you can read: "For printing/exporting, you can use a Web template other than the current Web template. In this case, all Web items and data provider

  • Cannot run InDesign CS5 trial

    I downloaded the InDesign CS5 trial.  It downloaded fien in Mozilla Firefox and when it begins to go through the installation process, it tells me I do not meet the standard requirements. I downloaded InDesign to run the program anyways and upon open

  • In CS6 I get a CS4 error message?  How to cure?

    I have deactivated and uninstalled CS4 from a laptop. CS5 was installed but never activated, it is uninstalled.   I have installed, updated and activated CS6.  I cannot open .psd or .jpg files from Bridge by any rouite I know.  I get:  "Windows canno

  • Service vendor master

    hi, is there necessary to tick on the indicator GR based IV in case of service vendor?