Kernel panic / Internet access with a bad AirPort card

My iBook G4 started suffering kernel panics just over a week ago. They have rapidly increased in frequency to the extent that it can take several attempts to boot up because they have started occurring during the boot up process (originally they occurred after the iBook had been on for a while).
I've looked through the forum and have seen that there seem to be some common causes -RAM, AirPort card, or something to do with the HD. I ran disk utility on the HD and it didn't find any problems and I also successfully ran the 'repair disk permissions'. I have tried taking out the RAM -that didn't do anything. The kernel panic does frequently occur when I am either using Mail or Safari, but as I've said, it also occurs when I'm booting up -does the fact that it happens when I boot up mean that it cannot be the AirPort card (which incidentally is not under the keyboard -so it must be inside)?
Earlier today I switched off AirPort and was able to work on the computer for almost three hours without any kernel panic (but also without internet access). Less than a minute after switching it back on, it froze again.
If this does mean that the problem is with the AirPort card, I have a question about internet access. I use the iBook on a wireless network that stems from a modem with a Mac downstairs and I do not have any internet cables, or a phone line, in the room where the iBook is used. Is it possible to use something like AirPort Express even with a bad AirPort card? And does AirPort Express connect to the iBook, or to the main modem downstairs?
Apologies for so many questions and many thanks for any help you are able to give -this has been driving me around the bend for the past week?

Update:
An acquaintance who works for Apple suggested that before assuming that the problem was the AirPort card / buying further equipment, I should boot up with the original installation disk in and use the disk utility function to 'repair disk'. I did that and got a 'Volume Header needs minor repair' message. It repaired that & I restarted the iBook. I was able to do an update back-up to my external hard drive & all was fine until I switched AirPort back on -there was an instant kernel panic.
I figured that it couldn't hurt to run the Apple Hardware Test -did that and restarted again. Was able to open Mail (AirPort was on) but then the AirPort connection disappeared and the pointer froze, but there was no kernel panic screen. I had to force quit -restarted again. This time I was able to use Mail, downloaded a song on iTunes, and was on the internet for about 45mins before the connection disappeared and the pointer froze again. I could force quit the app but with a frozen pointer I ended up having to force quit again.
I waited a while and then booted up again (without problem) but this time I was told that there was no Airport card present! Shut down and reran the Hardware Test (which said that AirPort 'Passed'). When I restarted AirPort was briefly there but disappeared when I opened AirPort Utility and at this point the pointer also froze. I did force quit to get out of the app and then there was a kernel panic. Is this now pretty conclusive that the AirPort card is the problem?
I would appreciate any feedback -I've had a very frustrating week with this.
Thanks.

Similar Messages

  • Can't get internet access with WRT54G router

    I recently purchased a used WRT54G. I replaced my old wired linksys router with it and my hosts are able to get dhcp addresses from the router, but they cannot access the Internet. I have tried to use dchp release and renew buttons under the status tab in the router's web-based gui to get a public IP address, but can't get one. I have attempted to reset the router to its factory settings, but I still can't get the public IP. I have no problem getting an IP and Internet access with my old router and the WRT54G works if I disable its dchp and daisy chain it to the old one. Maybe I need to do something else for a complete reset of the router. Any suggestions? Thanks, Jack

    the router that you just purchased was maybe configured for a different network before that's why it did not work initially. after making the router back to its' factory defaults, you should reconfigure or set-up the router.. If you have CABLE ISP, enable ''mac address clone'' on the router's set-up page under the set-up tab. then check if you can get a public ip address after that.

  • 10.7.1 and 10.7.2 - Kernel Panic on Boot with Filevault

    My filevaulted systems are having kernel panic on boot with both 10.7.1 and 10.7.2 updates.  I have to connect the time capsule to get it to boot and fix disk permissions before I can pull the firewire out and reboot by itself.
    Anyone else?

    Hi, Brian. I had only keyboard and mouse plugged into USB. I variously had a pair of LaCie 1TB drives in the FW800 in daisychain.
    It is now working again after running the single-user mode scripts from Leopard Cache Cleaner.
    It may arise again, but the initial cause remains mysterious, the intermediate cause perhaps being a polluted boot cache. I'm hoping I'm good from here. (fingers crossed)

  • Help!!!  Brand new MBP with Santa Rosa Kernel Panics when started with...

    Help!!! Brand new MBP with Santa Rosa Kernel Panics when started with external HD firewire 800 after 20 sec...
    I don't know what it could be???
    Do you???
    Thanx
    Jay

    I'm actually having a similar issue and I don't think its related to networking at all.
    I'm currently working in a corporate environment where we deploy pre-built OS X images to machines. I recently upgraded my images to 10.4.10 before we got our first Santa Rosa machine. This image was built on a MacPro and worked on all Intel Macs down to a MacMini CoreSolo. When I deployed my prebuilt image to the SR MBP, it caused a kernel panic immediately.
    Further investigation revealed previous builds of OS X, including 10.4.10 upgraded from any other model Intel Mac will kernel panic the SR MBP. Going backwards the SR Build of OSX will not work on any previous model Mac, as any other build typically does, but causes severe graphical distortion, as if it does not have the display drivers for the other Macs.
    To make a long story short, I think your issue comes from the fact that your external hard drive has an older build of OS X 10.4 than the SR MBP will run (even though you may have upgraded it to 10.4.10). Anyone who can corroborate my story with some more testing, please chime in.
    I haven't found a solution for this issue yet other than keeping a seperate Santa Rosa Core 2 Duo image for my deployments.

  • Software for controlling internet access with Airport Exreme

    I'd like to find software that let's me control what pc's in the house have internet access at certain times. My iMac is my main computer, and I use Airport Extreme as my router.

    You probably need to set the card up in OSX. Verizon should have a modem script that needs to be installed. (Hard Drive>Library>Modem Scripts). Then you need to set up the card from Network Preferences. Then it should work on both platforms.

  • Kernel Panic on iMac with Pixelated Video Issues

    One of our work iMacs has been having weird pixelate video issues recently. Sometimes previews of program windows will freeze on screen... and as you move the window around the screen "erases" this preview from the LCD... It is a 2006 24" White iMac 6,1. Now we get some Kernel Panics with the following error message. Please help me decipher it. Thanks!
    Interval Since Last Panic Report:  8641685 sec
    Panics Since Last Report:          1
    Anonymous UUID:                    E865F049-A575-4D59-A574-9D24C6EFD141
    Fri Mar 30 07:35:41 2012
    Backtrace (CPU 1), Frame : Return Address (4 potential args on stack)
    0x43923bb8 : 0x21b837 (0x5dd7fc 0x43923bec 0x223ce1 0x0)
    0x43923c08 : 0x2abf6a (0x59e3d0 0x53c01f 0xe 0x59e59a)
    0x43923ce8 : 0x2a1a78 (0x43923d00 0x0 0x43923da8 0x53c01f)
    0x43923cf8 : 0x53c01f (0xe 0x48 0x10 0x10)
    0x43923da8 : 0x53d2f5 (0x78f3000 0x785c240 0x43923df8 0x78f3000)
    0x43923dc8 : 0x570fcd (0x78f3000 0x785c240 0x43923de8 0x2a45c9)
    0x43923e18 : 0x28bb49 (0x78f3000 0x749a4a0 0x749a4b8 0x2106d8)
    0x43923e58 : 0x21dbe5 (0x749a0a4 0x749a484 0x43923ea8 0x3a23)
    0x43923e98 : 0x210a86 (0x749a000 0x0 0xbc747a0 0x7f6b690)
    0x43923ef8 : 0x216f84 (0x749a000 0x0 0x0 0x0)
    0x43923f78 : 0x295c57 (0x7daf5e8 0x0 0x0 0x0)
    0x43923fc8 : 0x2a256d (0x7daf5e4 0x0 0x10 0x0)
    BSD process name corresponding to current thread: Dock
    Mac OS version:
    10K549
    Kernel version:
    Darwin Kernel Version 10.8.0: Tue Jun  7 16:33:36 PDT 2011; root:xnu-1504.15.3~1/RELEASE_I386
    System model name: iMac6,1 (Mac-F4218FC8)
    System uptime in nanoseconds: 154254231492
    unloaded kexts:
    (none)
    loaded kexts:
    com.apple.driver.AppleHWSensor          1.9.3d0 - last loaded 121081986701
    com.apple.filesystems.autofs          2.1.0
    com.apple.driver.AppleTyMCEDriver          1.0.2d2
    com.apple.driver.InternalModemSupport          2.6.2
    com.apple.driver.AudioAUUC          1.57
    com.apple.driver.AppleIntelYonahProfile          14
    com.apple.driver.AppleUpstreamUserClient          3.5.7
    com.apple.driver.AppleIntelPenrynProfile          17
    com.apple.Dont_Steal_Mac_OS_X          7.0.0
    com.apple.driver.AppleMCCSControl          1.0.20
    com.apple.driver.AppleIntelNehalemProfile          11
    com.apple.driver.AppleHDA          2.0.5f14
    com.apple.driver.AudioIPCDriver          1.1.6
    com.apple.driver.AppleGraphicsControl          2.10.6
    com.apple.GeForce          6.3.6
    com.apple.driver.AppleIntelMeromProfile          19
    com.apple.driver.ACPI_SMC_PlatformPlugin          4.7.0a1
    com.apple.driver.AppleBacklight          170.0.46
    com.apple.driver.AppleLPC          1.5.1
    com.apple.driver.AppleIRController          303.8
    com.apple.driver.CSRHIDTransitionDriver          2.4.5f3
    com.apple.driver.USBCameraFirmwareLoader          1.1.0
    com.apple.iokit.SCSITaskUserClient          2.6.8
    com.apple.BootCache          31.1
    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
    com.apple.driver.AppleUSBHub          4.2.4
    com.apple.driver.AppleFWOHCI          4.7.3
    com.apple.driver.AirPortBrcm43xx          423.91.27
    com.apple.driver.AirPortBrcm43224          428.42.4
    com.apple.iokit.AppleYukon2          3.2.1b1
    com.apple.iokit.IOAHCIBlockStorage          1.6.4
    com.apple.driver.AppleEFINVRAM          1.4.0
    com.apple.driver.AppleUSBEHCI          4.2.4
    com.apple.driver.AppleAHCIPort          2.1.7
    com.apple.driver.AppleIntelPIIXATA          2.5.1
    com.apple.driver.AppleUSBUHCI          4.2.0
    com.apple.driver.AppleRTC          1.3.1
    com.apple.driver.AppleHPET          1.5
    com.apple.driver.AppleACPIButtons          1.3.6
    com.apple.driver.AppleSMBIOS          1.7
    com.apple.driver.AppleACPIEC          1.3.6
    com.apple.driver.AppleAPIC          1.4
    com.apple.driver.AppleIntelCPUPowerManagementClient          142.6.0
    com.apple.security.sandbox          1
    com.apple.security.quarantine          0
    com.apple.nke.applicationfirewall          2.1.14
    com.apple.driver.AppleIntelCPUPowerManagement          142.6.0
    com.apple.driver.AppleProfileReadCounterAction          17
    com.apple.driver.AppleProfileTimestampAction          10
    com.apple.driver.AppleProfileThreadInfoAction          14
    com.apple.driver.AppleProfileRegisterStateAction          10
    com.apple.driver.AppleProfileKEventAction          10
    com.apple.driver.AppleProfileCallstackAction          20
    com.apple.iokit.IOSurface          74.2
    com.apple.iokit.IOBluetoothSerialManager          2.4.5f3
    com.apple.iokit.IOSerialFamily          10.0.3
    com.apple.driver.AppleHDAHardwareConfigDriver          2.0.5f14
    com.apple.driver.DspFuncLib          2.0.5f14
    com.apple.iokit.IOAudioFamily          1.8.3fc2
    com.apple.kext.OSvKernDSPLib          1.3
    com.apple.iokit.IOFireWireIP          2.0.3
    com.apple.iokit.AppleProfileFamily          41
    com.apple.driver.AppleHDAController          2.0.5f14
    com.apple.iokit.IOHDAFamily          2.0.5f14
    com.apple.driver.AppleSMC          3.1.0d5
    com.apple.driver.IOPlatformPluginFamily          4.7.0a1
    com.apple.driver.AppleSMBusPCI          1.0.10d0
    com.apple.driver.AppleBacklightExpert          1.0.1
    com.apple.nvidia.nv40hal          6.3.6
    com.apple.NVDAResman          6.3.6
    com.apple.iokit.IONDRVSupport          2.2.1
    com.apple.iokit.IOGraphicsFamily          2.2.1
    com.apple.driver.CSRUSBBluetoothHCIController          2.4.5f3
    com.apple.driver.AppleUSBBluetoothHCIController          2.4.5f3
    com.apple.iokit.IOBluetoothFamily          2.4.5f3
    com.apple.iokit.IOUSBHIDDriver          4.2.0
    com.apple.driver.AppleUSBMergeNub          4.2.4
    com.apple.iokit.IOSCSIBlockCommandsDevice          2.6.8
    com.apple.iokit.IOUSBMassStorageClass          2.6.7
    com.apple.driver.AppleUSBComposite          3.9.0
    com.apple.iokit.IOSCSIMultimediaCommandsDevice          2.6.8
    com.apple.iokit.IOBDStorageFamily          1.6
    com.apple.iokit.IODVDStorageFamily          1.6
    com.apple.iokit.IOCDStorageFamily          1.6.1
    com.apple.iokit.IOATAPIProtocolTransport          2.5.1
    com.apple.iokit.IOSCSIArchitectureModelFamily          2.6.8
    com.apple.driver.XsanFilter          402.1
    com.apple.driver.AppleFileSystemDriver          2.0
    com.apple.iokit.IOUSBUserClient          4.2.4
    com.apple.iokit.IOFireWireFamily          4.2.6
    com.apple.iokit.IO80211Family          320.1
    com.apple.iokit.IONetworkingFamily          1.10
    com.apple.iokit.IOAHCIFamily          2.0.6
    com.apple.iokit.IOATAFamily          2.5.1
    com.apple.iokit.IOUSBFamily          4.2.4
    com.apple.driver.AppleEFIRuntime          1.4.0
    com.apple.iokit.IOHIDFamily          1.6.6
    com.apple.iokit.IOSMBusFamily          1.1
    com.apple.security.TMSafetyNet          6
    com.apple.kext.AppleMatch          1.0.0d1
    com.apple.driver.DiskImages          289
    com.apple.iokit.IOStorageFamily          1.6.3
    com.apple.driver.AppleACPIPlatform          1.3.6
    com.apple.iokit.IOPCIFamily          2.6.5
    com.apple.iokit.IOACPIFamily          1.3.0
    Model: iMac6,1, BootROM IM61.0093.B07, 2 processors, Intel Core 2 Duo, 2.16 GHz, 4 GB, SMC 1.10f2
    Graphics: NVIDIA GeForce 7300 GT, NVIDIA GeForce 7300 GT, PCIe, 128 MB
    Memory Module: global_name
    AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x87), Broadcom BCM43xx 1.0 (5.10.131.42.4)
    Bluetooth: Version 2.4.5f3, 2 service, 19 devices, 1 incoming serial ports
    Network Service: Built-in Ethernet, Ethernet, en0
    Serial ATA Device: ST3320620AS, 298.09 GB
    Parallel ATA Device: MATSHITADVD-R   UJ-85J
    USB Device: Built-in iSight, 0x05ac  (Apple Inc.), 0x8501, 0xfd400000 / 2
    USB Device: Express USB2, 0x0dc4  (Macpower Peripherals Ltd.), 0x00db, 0xfd500000 / 3
    USB Device: Hub in Apple Pro Keyboard, 0x05ac  (Apple Inc.), 0x1003, 0x1d100000 / 2
    USB Device: USB Receiver, 0x046d  (Logitech Inc.), 0xc50a, 0x1d110000 / 4
    USB Device: Apple Pro Keyboard, 0x05ac  (Apple Inc.), 0x020b, 0x1d130000 / 3
    USB Device: Bluetooth USB Host Controller, 0x05ac  (Apple Inc.), 0x8206, 0x7d100000 / 2
    USB Device: IR Receiver, 0x05ac  (Apple Inc.), 0x8240, 0x7d200000 / 3

    Re: Kernel Panic on iMac Intel Core 2 Duo with Lion 10.7.1, 4gb RAM
    27-sep-2011 11:53 (in response to jose guzman) Launch the Apple Hardware Test program, run the extended tests at least twice, and then download and run Rember. All indications are that you have bad or flaky RAM.
    27" i7 iMac 10.6.8 , Mac OS X (10.7.1), G4 450 MP 1.5 GB RAM w/(10.5.8/10.4.11/9.2.2) 
    I did that and it doesn't work

  • Kernel Panic everytime MBP with Mountain Lion shuts down

    Hello,
    My MBP (MBP 7,1, 2.4gHz Intel Core 2 Duo, 4GB DDR3 Ram, 500GB hard drive with Mountain Lion 10.8.2) recently started having kernel panics every time I shut down. It reboot twice and then show the "please report this to Apple" dialogue box followed by the "kernel dump" dialogue box. Is there anyway I can fix this?
    Thanks,
    Tony
    Console Dump:
    Interval Since Last Panic Report:  342434 sec
    Panics Since Last Report:          1
    Anonymous UUID:                    36939FEC-D869-066B-00EA-0CB3ACF408A3
    Mon Oct 22 09:14:10 2012
    panic(cpu 1 caller 0xffffff80086b7bd5): Kernel trap at 0xffffff800862d507, type 13=general protection, registers:
    CR0: 0x000000008001003b, CR2: 0x00007fff89690488, CR3: 0x000000000b30d000, CR4: 0x0000000000000660
    RAX: 0xffffff8013576000, RBX: 0xffffff8013576000, RCX: 0xffffff808083bfc0, RDX: 0xffffff8080838000
    RSP: 0xffffff808083be00, RBP: 0xffffff808083be40, RSI: 0x01ffff8013602000, RDI: 0xffffff8013576000
    R8:  0xffffff8013576000, R9:  0x0000000000000000, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
    R12: 0xffffff8008cbebe8, R13: 0x0000000000000000, R14: 0x01ffff8013602000, R15: 0x0000000000000000
    RFL: 0x0000000000010086, RIP: 0xffffff800862d507, CS:  0x0000000000000008, SS:  0x0000000000000010
    Fault CR2: 0x00007fff89690488, Error code: 0x0000000000000000, Fault CPU: 0x1
    Backtrace (CPU 1), Frame : Return Address
    0xffffff808083baa0 : 0xffffff800861d626
    0xffffff808083bb10 : 0xffffff80086b7bd5
    0xffffff808083bce0 : 0xffffff80086ce4ed
    0xffffff808083bd00 : 0xffffff800862d507
    0xffffff808083be40 : 0xffffff800862e74f
    0xffffff808083bec0 : 0xffffff800862da0c
    0xffffff808083bf00 : 0xffffff800861c7f7
    0xffffff808083bf20 : 0xffffff7f896b963f
    0xffffff808083bf40 : 0xffffff7f896b2ad5
    0xffffff808083bf60 : 0xffffff800863dcde
    0xffffff808083bfb0 : 0xffffff80086b26b7
          Kernel Extensions in backtrace:
             com.apple.driver.AppleUSBHub(5.2.5)[A70C7553-FFEA-355F-A292-6E2B0023FADD]@0xfff fff7f896b0000->0xffffff7f896c4fff
                dependency: com.apple.iokit.IOUSBFamily(5.4.0)[C3094550-7F58-3933-A4F7-CD33AE83F8B9]@0xffff ff7f89540000
    BSD process name corresponding to current thread: kernel_task
    Mac OS version:
    Not yet set
    Kernel version:
    Darwin Kernel Version 12.2.0: Sat Aug 25 00:48:52 PDT 2012; root:xnu-2050.18.24~1/RELEASE_X86_64
    Kernel UUID: 69A5853F-375A-3EF4-9247-478FD0247333
    Kernel slide:     0x0000000008400000
    Kernel text base: 0xffffff8008600000
    System model name: MacBookPro7,1 (Mac-F222BEC8)
    System uptime in nanoseconds: 3507874655
    last loaded kext at 1632739838: com.apple.driver.AppleUSBTCButtons          235.4 (addr 0xffffff7f8a339000, size 20480)
    loaded kexts:
    com.apple.driver.AppleUSBTCButtons          235.4
    com.apple.driver.AppleIRController          320.15
    com.apple.driver.CoreStorageFsck          274.7
    com.apple.driver.AppleUSBTCKeyEventDriver          235.4
    com.apple.driver.AppleUSBTCKeyboard          235.4
    com.apple.driver.AppleFileSystemDriver          3.0.1
    com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
    com.apple.BootCache          34
    com.apple.driver.AppleUSBCardReader          3.1.0
    com.apple.iokit.SCSITaskUserClient          3.5.1
    com.apple.driver.XsanFilter          404
    com.apple.iokit.IOAHCIBlockStorage          2.2.2
    com.apple.iokit.AppleBCM5701Ethernet          3.2.5b3
    com.apple.driver.AppleSmartBatteryManager          161.0.0
    com.apple.driver.AirPort.Brcm4331          602.15.22
    com.apple.driver.AppleIntelCPUPowerManagementClient          196.0.0
    com.apple.driver.AppleUSBHub          5.2.5
    com.apple.driver.AppleFWOHCI          4.9.6
    com.apple.driver.AppleAHCIPort          2.4.1
    com.apple.driver.AppleUSBEHCI          5.4.0
    com.apple.driver.AppleUSBOHCI          5.2.5
    com.apple.driver.AppleEFINVRAM          1.6.1
    com.apple.driver.AppleRTC          1.5
    com.apple.driver.AppleHPET          1.7
    com.apple.driver.AppleACPIButtons          1.6
    com.apple.driver.AppleSMBIOS          1.9
    com.apple.driver.AppleACPIEC          1.6
    com.apple.driver.AppleAPIC          1.6
    com.apple.nke.applicationfirewall          4.0.39
    com.apple.security.quarantine          2
    com.apple.driver.AppleIntelCPUPowerManagement          196.0.0
    com.apple.driver.AppleUSBMultitouch          235.7
    com.apple.iokit.IOUSBHIDDriver          5.2.5
    com.apple.driver.CoreStorage          274.7
    com.apple.iokit.IOSCSIBlockCommandsDevice          3.5.1
    com.apple.iokit.IOUSBMassStorageClass          3.5.0
    com.apple.driver.AppleUSBMergeNub          5.2.5
    com.apple.driver.AppleUSBComposite          5.2.5
    com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.5.1
    com.apple.iokit.IOBDStorageFamily          1.7
    com.apple.iokit.IODVDStorageFamily          1.7.1
    com.apple.iokit.IOCDStorageFamily          1.7.1
    com.apple.iokit.IOAHCISerialATAPI          2.5.0
    com.apple.iokit.IOSCSIArchitectureModelFamily          3.5.1
    com.apple.iokit.IOEthernetAVBController          1.0.2b1
    com.apple.iokit.IO80211Family          500.15
    com.apple.iokit.IONetworkingFamily          3.0
    com.apple.iokit.IOUSBUserClient          5.2.5
    com.apple.iokit.IOFireWireFamily          4.5.5
    com.apple.driver.AppleMCP89RootPortPM          1.11
    com.apple.iokit.IOAHCIFamily          2.2.1
    com.apple.iokit.IOUSBFamily          5.4.0
    com.apple.driver.NVSMU          2.2.9
    com.apple.driver.AppleEFIRuntime          1.6.1
    com.apple.iokit.IOHIDFamily          1.8.0
    com.apple.iokit.IOSMBusFamily          1.1
    com.apple.security.sandbox          220
    com.apple.kext.AppleMatch          1.0.0d1
    com.apple.security.TMSafetyNet          7
    com.apple.driver.DiskImages          344
    com.apple.iokit.IOStorageFamily          1.8
    com.apple.driver.AppleKeyStore          28.21
    com.apple.driver.AppleACPIPlatform          1.6
    com.apple.iokit.IOPCIFamily          2.7.2
    com.apple.iokit.IOACPIFamily          1.4
    com.apple.kec.corecrypto          1.0
    Model: MacBookPro7,1, BootROM MBP71.0039.B0E, 2 processors, Intel Core 2 Duo, 2.4 GHz, 4 GB, SMC 1.62f6
    Graphics: NVIDIA GeForce 320M, NVIDIA GeForce 320M, PCI, 256 MB
    Memory Module: BANK 0/DIMM0, 2 GB, DDR3, 1067 MHz, 0x80AD, 0x484D54313235533654465238432D47372020
    Memory Module: BANK 1/DIMM0, 2 GB, DDR3, 1067 MHz, 0x80AD, 0x484D54313235533654465238432D47372020
    AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8D), Broadcom BCM43xx 1.0 (5.106.98.81.22)
    Bluetooth: Version 4.0.9f33 10885, 2 service, 11 devices, 1 incoming serial ports
    Network Service: Wi-Fi, AirPort, en1
    Serial ATA Device: WDC WD5000BPVT-00HXZT1, 500.11 GB
    Serial ATA Device: HL-DT-ST DVDRW  GS23N
    USB Device: Built-in iSight, apple_vendor_id, 0x8507, 0x24600000 / 2
    USB Device: Internal Memory Card Reader, apple_vendor_id, 0x8403, 0x26100000 / 2
    USB Device: Microsoft 3-Button Mouse with IntelliEye(TM), 0x045e  (Microsoft Corporation), 0x0040, 0x04100000 / 2
    USB Device: BRCM2046 Hub, 0x0a5c  (Broadcom Corp.), 0x4500, 0x06600000 / 4
    USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8213, 0x06610000 / 6
    USB Device: Apple Internal Keyboard / Trackpad, apple_vendor_id, 0x0236, 0x06300000 / 3
    USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x06500000 / 2

    Back up all data.
    Boot into Recovery by holding down the key combination command-R at the startup chime. Release the keys when you see a gray screen with a spinning dial.
    Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with networks that require any kind of authentication other than a WPA or WPA2 Personal password.
    When the OS X Utilities screen appears, follow the prompts to reinstall the OS. You don't need to erase the boot volume, and you won't need your backup unless something goes wrong. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade, so make a note of those before you begin.

  • Memory issues - kernel panics / system freezes with 1Gb Memory Card

    I've recently updated my PowerBook OS to 10.4.7 and now more recently 10.4.8.
    Prior to this, i had been running a pair of pc2700 memory cards (1x1Gb + 1x 512Mb) bought from crucial technology on 10.3.9 with no problems.
    During the upgrade, i experienced complete system lock ups and kernel panics. pulling the 1Gb card resolved the problem.
    So i thought it could be duff memory (it happens). I ran hardware checker, both long and short tests, ran memchecker from single user and there was no reported errors although i was still getting crashes.
    I returned the memory to crucial and they replaced it and then i went to reinstall memory in the pb.
    Once reinstalled, problems re-emerged. Both System profiler and iStat pro show both memory sticks as ok. both are pc2700 DDR.
    i tried just the 1 Gb stick in alternate memory slots. with the memory in the lower slot i was getting system freezes, in the top slot i was getting kernel panics.
    I've pulled the 1Gb and reverted to 768Mb (512Mb lower (crucial)/ 256MB (apple) upper) and i'm back to normal.
    Now what?
    As my mac is getting on, i'd like to get as much RAM in it as i can, ideally the 1.5Gb /2Gb which it can support. I'd be suprised if it could be the memory stick being duff (2 duff in a row?), its not a faulty memory slot as system profiler is showing that its full.
    Any suggestions? Anything to do with how 10.4.8 handles the memory addressing?
    Any help would be appreciated.
    PowerBook G4 1Ghz FW800   Mac OS X (10.4.8)  

    I've had that problem, too. I found out that it was one of my memory modules that were broken.
    I'd say pop back in your other memory module, then get out your PowerBook DVD and stick it in Restart your PowerBook while holding down the Option Key on your keyboard until some buttons start to show up on your screen.
    Select the Hardware Test one, then click the Arrow button. It'll boot into a utility and you can run a hardware test that includes checking your memory.
    If any of your memory is bad, it'll show up like "**ERROR ERROR**" and give you a code.
    After you've identified the hardware problem (hopefully just the RAM), then you can go to Crucial's website and fill out an RMA request to have the memory replaced. I'm pretty sure Crucial has a life-time warranty on their memory products.

  • Kernel Panic + Internet Crashing

    This has been happening since 2 days ago, my internet explorers have been crashing constantly at around 8pm (first I thought it was only Firefox but then I realised that the same thing happens with Safari) and then I have the message that tells you to restart the computer (Kernel Panic). I think that the reason for this is that I don't have the 10.6.3 upgrade, but when I try to upgrade to this version and to iTunes 9.1 there's an error during the installation, and I've seen in other forums that I'm not the only one with this error during the upgrade. Right now I'm downloading the upgrade from my PC and then I'm going to install it on my iMac to see if this solves the problem, I hope it does.
    Any recommendations?
    EDIT: Itunes and Microsoft Office are crashing too...
    Message was edited by: arnus

    Welcome to the discussions.
    Kernel panic is usually but not always, a hardware related problem. Did you upgrade the RAM or some other hardware. Or did you attach any new peripheral lately.
    As regards update to 10.6.3 I would suggest use the combo updater and not via software update. You can download the combo update here http://support.apple.com/kb/DL1017

  • No Internet Access with Static IP and RVS 4000

    I have an RVS 4000.  I have several PC's to which I have assigned static IP addresses.  I have recently upgraded most of the PC's to Win 7 (64) machines.  I updated the firmware on the RVS4000 to 1.3.3.5 in conjunction with this.  After such update (and actually before as well) I could not assign a static IP address to a PC and have access to the internet.  It connects fine to my LAN, just no internet access.  This is also affected on several other machines running Win XP and Win 2003 Server, so it's not just this computer. 
    I have:
         1.  Shut down (powered off/unplugged) everything, router, DSL modem, switches, server, etc.
         2.  As I said firmware is current.
         3.  Yes, DNS servers and gateway, subnet, etc. are all correctly specified on the PC.
         4.  Router is set for gateway mode.
         5.  Set to only IPV4.
    The only way it allows internet access is to use DHCP.  I've even tried taking the IP address via DHCP and manually assigning the DNS servers and that works fine, but as soon as I assign a static IP internet access is immediately gone.
    There must be something I'm missing, but I can't seem to find it.
    Everything worked fine prior to the conversion of the Win 7 machines, i.e. I had several PC's with static IP's and no problems.
    Any thoughts appreciated.

    As an addendum, if I turn off the Firewall (internet access policy to disable) it will allow the static IP computer to have internet access.  I have the DHCP range set to be .5 - .54 and am using a static ip outside this range.  The Internet access policy is to restrict those PC's getting IP via DHCP.

  • No internet access with iphone 3GS ios5 personal hotspot

    Prior to upgrading to IOS5 I was able to tether my Windows box to my iPhone 3GS.  Now with the upgrade I'm not able to connect using the new Personal Hotspot method that was introduced.  I can connect the phone, and actually see a network show up in my network connections but I get no internet access through it.  I can ping the Gateway that the network gets but that's it.  Can't ping the DNS server or anything else.  Any ideas here would be very appreciated.
    Ethernet adapter Local Area Connection 3:
       Connection-specific DNS Suffix  . :
       Description . . . . . . . . . . . : Apple Mobile Device Ethernet
       Physical Address. . . . . . . . . : 02-26-B0-B9-F5-6C
       DHCP Enabled. . . . . . . . . . . : Yes
       Autoconfiguration Enabled . . . . : Yes
       Link-local IPv6 Address . . . . . : XXXX
       IPv4 Address. . . . . . . . . . . : 172.XX.XX.X(Preferred)
       Subnet Mask . . . . . . . . . . . : 255.255.255.240
       Lease Obtained. . . . . . . . . . : Wednesday, February 01, 2012 11:21:30 AM
       Lease Expires . . . . . . . . . . : Thursday, February 02, 2012 11:07:06 AM
       Default Gateway . . . . . . . . . : 172.20.10.1
       DHCP Server . . . . . . . . . . . : 172.20.10.1
       DHCPv6 IAID . . . . . . . . . . . : XXX
       DHCPv6 Client DUID. . . . . . . . : XXXX
       DNS Servers . . . . . . . . . . . : 64.71.255.198
                                           64.71.255.253
       NetBIOS over Tcpip. . . . . . . . : Enabled
    Thanks,
    Foody

    Do the basic troubleshooting steps with your phone, as needed:
    Restart phone
    Reset phone
    Settings > General > Reset > Reset Network Settings
    Restore phone in iTunes using a backup
    Restore in iTunes as new, without using a backup
    See the User Guide for info on how to do these steps/

  • Good Signal, but not Internet with built-in Airport card

    Hi,
    I'm sorry if this is a duplicate question, but I couldn't seem to find a similar situation. I'm trying to get my wireless (or any) Internet working at my house with my Powerbook G4 with a built-in Airport card. We have a Linksys 802.11g router with no security enabled. My mac is picking up a very strong signal, but everytime I go to Safari, iTunes, or Explorer it says there's no internet connection present (yet internet connect and my network says I'm connected through Airport).
    I've had my wireless and ethernet working on this computer before -- picking up a variety of signals, including other linksys routers. All of the PCs in the house are working fine with this, and my mac even shows up on our router list.
    The most recent experience I had with internet on my mac was earlier this week--i took it into my work to do some testing and we had to set up a specific location to get it to work through that ethernet network. When I took it home, I removed all of those configurations and tried both my wireless and ethernet, and I can not get either working. At this point, I've removed all of my configurations and tried reconfiguring. Everything but my airport is turned off. No proxies are selected. I've turned off the iPv6. I'm using DHCP (which is showing the correct router and IP address). I've deleted the System Configuration folder from Preferences. And it's on the top of the list in network and have selected Airport as the default. And none of this seems to be working. Oh, and I tested to see if it was a DNS problem (which I head read in one discussion forum), and that didn't fix it. I'm sure it's something simple that I'm missing. But I can't for the life of me get it to work.
    Does anyone have any thoughts? suggestions? insights? help?
    Please? I'm pulling my hair out trying to figure out what this could be.
    Thanks so much in advance.
    meg.

    Joel,
    I am having the same exact problem and have had it for months now.
    Here is my tcpdump, hope you can help.
    Last login: Sat Sep 2 11:46:05 on ttyp1
    Welcome to Darwin!
    Orion:~ tarlach$ sudo tcpdump -nni en1
    Password:
    tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
    listening on en1, link-type EN10MB (Ethernet), capture size 96 bytes
    12:54:33.236551 IP 169.254.196.234 > 224.0.0.251: igmp v2 report 224.0.0.251
    12:54:33.635688 IP 169.254.196.234.5353 > 224.0.0.251.5353: 0 [5q][|domain]
    12:54:33.635896 fe80::20d:93ff:fe84:ba8c.5353 > ff02::fb.5353: 0 [5q][|domain]
    12:54:34.647999 IP 169.254.196.234.5353 > 224.0.0.251.5353: 0*- [0q] 9/0/0[|domain]
    12:54:34.648258 fe80::20d:93ff:fe84:ba8c.5353 > ff02::fb.5353: 0*- [0q] 9/0/0[|domain]
    12:54:35.436941 fe80::20d:93ff:fe84:ba8c > ff02::fb: HBH icmp6: multicast listener report max resp delay: 0 addr: ff02::fb [hlim 1]
    12:54:35.648474 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 00:0d:93:84:ba:8c, length: 300
    12:54:35.954863 fe80::20d:93ff:fe84:ba8c > ff02::2: icmp6: router solicitation
    12:54:41.635570 IP 169.254.196.234.5353 > 224.0.0.251.5353: 0 [5q][|domain]
    12:54:41.635820 fe80::20d:93ff:fe84:ba8c.5353 > ff02::fb.5353: 0 [5q][|domain]
    12:54:42.647940 IP 169.254.196.234.5353 > 224.0.0.251.5353: 0*- [0q] 9/0/0[|domain]
    12:54:42.648177 fe80::20d:93ff:fe84:ba8c.5353 > ff02::fb.5353: 0*- [0q] 9/0/0[|domain]
    12:54:43.804966 IP 192.168.2.4.631 > 192.168.2.255.631: UDP, length: 112
    12:54:44.472343 fe80::20d:93ff:fe84:ba8c > ff02::2: icmp6: router solicitation
    12:54:44.534688 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 00:0d:93:84:ba:8c, length: 300
    12:54:52.940381 fe80::20d:93ff:fe84:ba8c > ff02::2: icmp6: router solicitation
    12:54:53.020918 IP 192.168.2.4.631 > 192.168.2.255.631: UDP, length: 83
    12:54:53.457391 arp who-has 192.168.2.1 tell 0.0.0.0
    12:54:53.457981 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 00:0d:93:84:ba:8c, length: 300
    12:54:53.458573 arp reply 192.168.2.1 is-at 00:11:50:4f:4a:40
    12:54:55.785686 IP 192.168.2.4.631 > 192.168.2.255.631: UDP, length: 76
    12:54:57.635663 IP 169.254.196.234.5353 > 224.0.0.251.5353: 0 [5q][|domain]
    12:54:57.635911 fe80::20d:93ff:fe84:ba8c.5353 > ff02::fb.5353: 0 [5q][|domain]
    12:54:58.646996 IP 169.254.196.234.5353 > 224.0.0.251.5353: 0*- [0q] 9/0/0[|domain]
    12:54:58.647240 fe80::20d:93ff:fe84:ba8c.5353 > ff02::fb.5353: 0*- [0q] 9/0/0[|domain]
    12:55:01.016643 fe80::20d:93ff:fe84:ba8c > ff02::2: icmp6: router solicitation
    12:55:02.149064 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 00:0d:93:84:ba:8c, length: 300
    12:55:09.439854 fe80::20d:93ff:fe84:ba8c > ff02::2: icmp6: router solicitation
    12:55:10.767834 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 00:0d:93:84:ba:8c, length: 300
    12:55:15.139955 IP 192.168.2.4.631 > 192.168.2.255.631: UDP, length: 112
    12:55:17.499395 fe80::20d:93ff:fe84:ba8c > ff02::2: icmp6: router solicitation
    12:55:19.379023 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from 00:0d:93:84:ba:8c, length: 300
    12:55:25.597876 fe80::20d:93ff:fe84:ba8c > ff02::2: icmp6: router solicitation
    12:55:27.120694 IP 192.168.2.4.631 > 192.168.2.255.631: UDP, length: 76
    12:55:29.634050 IP 169.254.196.234.5353 > 224.0.0.251.5353: 0 [5q][|domain]
    12:55:29.634282 fe80::20d:93ff:fe84:ba8c.5353 > ff02::fb.5353: 0 [5q][|domain]
    12:55:30.646358 IP 169.254.196.234.5353 > 224.0.0.251.5353: 0*- [0q] 9/0/0[|domain]
    12:55:30.646601 fe80::20d:93ff:fe84:ba8c.5353 > ff02::fb.5353: 0*- [0q] 9/0/0[|domain]
    12:55:34.186230 IP 192.168.2.2.5353 > 224.0.0.251.5353: 0 [2q] PTR? daap.tcp.local. PTR? raop.tcp.local. (46)
    12:55:55.076547 IP 192.168.2.4.631 > 192.168.2.255.631: UDP, length: 83
    I cut it off as it seemed to want to just keep running.
    I am unable to get online in my own wep network, I can connect and get a strong signal b ut that is all.
    Please, if you can, help.
    thank yhou

  • Kernel Panic after restoring with Time Machine

    I'm trying to replace my 250GB HD with a 500GB one, but when I reboot after the TM restore, I receive a kernel panic. The message contains the error "panic .... /sbin/launchd, errno 8 ....", and then gives the stack trace. I think errno 8 is 'incorrect format', but I'm not sure what that means in this case. I don't know what to do next, and could use some suggestions.
    Here is the procedure I used:
    - Backup everything with TM to an external drive (500GB HD)
    - replace HD
    - boot from original OS X install DVD (10.5.5)
    - create a single volume on the new HD, using the whole HD
    - Restore from TM backup (completes in about 3 hours)
    - Boot from new HD - kernel panic each time
    A couple notes:
    I verified that /sbin/launchd exists on my TM backup.
    - I'm running 10.6, but I tried booting from my snow leopard disk (which I ordered shortly after receiving my computer), and that did not work, so I went back to using the original one I received with my computer (leopard). Could this be causing the problem?
    - The machine boots fine when I re-install the original 250GB drive, so I know I don't have any other h/w failures
    - With the new restored HD inserted as well as the install DVD, the machine wants to boot each time from the HD, and not the DVD, giving me an endless loop of kernel panics. I thought it would boot from the DVD if it's installed. Is there a way to over-ride, and select the media from which to boot?
    Any thoughts or suggestions are much appreciated.
    Thanks,
    Jeff

    WoodShavings wrote:
    Thank you for the quick response. Booting from the SL DVD, partitioning, and then a full restore has worked.
    Great!
    It did take a bit for me to figure out how to select the SL DVD - the HD already had a restore on it that was causing the panic. The 'alt' key is a great trick for selecting your boot device.
    So is the "C" key. That will boot from the CD (or DVD) in the SuperDrive.

  • Regular kernel panics, most noticeable with Flash usage. I suspect it has to do with RAM, hard drive space, or overheating.

    Hi, would massively appreciate it if anyone would be able to point me in the direction of what's causing fairly regular kernel panics and general poor performance of my 2007 Macbook. Running 2gb Ram, hard drive space is running low (90% full), but seems to operate fine until I hit flash videos, when it stutters, stalls, and, if I push it too far, crashes. Is it directly related to hard drive space? Here's the log:
    Interval Since Last Panic Report:  2259605 sec
    Panics Since Last Report:          8
    Anonymous UUID:                    8E803563-23BA-4850-B3FB-F4FFCAE6622A
    Thu Feb  2 12:10:45 2012
    panic(cpu 0 caller 0x28fc2e): "TLB invalidation IPI timeout: " "CPU(s) failed to respond to interrupts, unresponsive CPU bitmap: 0x0, NMIPI acks: orig: 0x0, now: 0x0"@/SourceCache/xnu/xnu-1504.15.3/osfmk/i386/pmap.c:3572
    Backtrace (CPU 0), Frame : Return Address (4 potential args on stack)
    0x34fb3b28 : 0x21b837 (0x5dd7fc 0x34fb3b5c 0x223ce1 0x0)
    0x34fb3b78 : 0x28fc2e (0x59a47c 0x0 0x0 0x0)
    0x34fb3be8 : 0x2944ee (0x5090d24 0x1d10c000 0x0 0x5)
    0x34fb3d78 : 0x255994 (0x5090d24 0x1d10c000 0x0 0x640e4)
    0x34fb3de8 : 0x2589af (0x2e5cf7c 0x5090d24 0x1d10c000 0x0)
    0x34fb3f38 : 0x2ab83c (0x509d0a4 0x1d10c000 0x0 0x3)
    0x34fb3fc8 : 0x2a18da (0x5b446c0 0x0 0x10 0x5b446c0)
    BSD process name corresponding to current thread: Google Chrome He
    Mac OS version:
    10K549
    Kernel version:
    Darwin Kernel Version 10.8.0: Tue Jun  7 16:33:36 PDT 2011; root:xnu-1504.15.3~1/RELEASE_I386
    System model name: MacBook2,1 (Mac-F4208CA9)
    System uptime in nanoseconds: 20169509378374
    unloaded kexts:
    (none)
    loaded kexts:
    com.google.driver.Gild          1.0.0 - last loaded 41377940038
    at.obdev.nke.LittleSnitch          2.0.25
    com.apple.filesystems.autofs          2.1.0
    com.apple.driver.AppleTyMCEDriver          1.0.2d2
    com.apple.driver.InternalModemSupport          2.6.2
    com.apple.driver.AudioAUUC          1.57
    com.apple.driver.AppleIntelYonahProfile          14
    com.apple.driver.AppleUpstreamUserClient          3.5.7
    com.apple.driver.AppleIntelPenrynProfile          17
    com.apple.Dont_Steal_Mac_OS_X          7.0.0
    com.apple.driver.AppleMCCSControl          1.0.20
    com.apple.driver.AppleIntelGMA950          6.3.6
    com.apple.driver.AppleIntelNehalemProfile          11
    com.apple.driver.AudioIPCDriver          1.1.6
    com.apple.driver.AppleHDA          2.0.5f14
    com.apple.driver.AirPort.Atheros          422.19.10
    com.apple.driver.AppleGraphicsControl          2.10.6
    com.apple.driver.SMCMotionSensor          3.0.1d2
    com.apple.iokit.AppleYukon2          3.2.1b1
    com.apple.driver.AppleIntelMeromProfile          19
    com.apple.driver.AirPort.Atheros21          425.14.7
    com.apple.driver.ACPI_SMC_PlatformPlugin          4.7.0a1
    com.apple.driver.AppleLPC          1.5.1
    com.apple.driver.AppleBacklight          170.0.46
    com.apple.driver.AppleIntelIntegratedFramebuffer          6.3.6
    com.apple.driver.CSRHIDTransitionDriver          2.4.5f3
    com.apple.driver.AppleIRController          303.8
    com.apple.driver.AppleUSBTrackpad          201.6
    com.apple.driver.AppleUSBTCKeyEventDriver          201.6
    com.apple.driver.AppleUSBTCKeyboard          201.6
    com.apple.iokit.IOAHCIBlockStorage          1.6.4
    com.apple.driver.USBCameraFirmwareLoader          1.1.0
    com.apple.iokit.SCSITaskUserClient          2.6.8
    com.apple.driver.AppleFWOHCI          4.7.3
    com.apple.BootCache          31.1
    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
    com.apple.driver.AppleEFINVRAM          1.4.0
    com.apple.driver.AppleAHCIPort          2.1.7
    com.apple.driver.AppleUSBHub          4.2.4
    com.apple.driver.AppleRTC          1.3.1
    com.apple.driver.AppleHPET          1.5
    com.apple.driver.AppleUSBEHCI          4.2.4
    com.apple.driver.AppleUSBUHCI          4.2.0
    com.apple.driver.AppleIntelPIIXATA          2.5.1
    com.apple.driver.AppleSmartBatteryManager          160.0.0
    com.apple.driver.AppleACPIButtons          1.3.6
    com.apple.driver.AppleSMBIOS          1.7
    com.apple.driver.AppleACPIEC          1.3.6
    com.apple.driver.AppleAPIC          1.4
    com.apple.driver.AppleIntelCPUPowerManagementClient          142.6.0
    com.apple.security.sandbox          1
    com.apple.security.quarantine          0
    com.apple.nke.applicationfirewall          2.1.14
    com.apple.driver.AppleIntelCPUPowerManagement          142.6.0
    com.apple.driver.AppleProfileReadCounterAction          17
    com.apple.driver.AppleProfileTimestampAction          10
    com.apple.driver.AppleProfileThreadInfoAction          14
    com.apple.driver.AppleProfileRegisterStateAction          10
    com.apple.driver.AppleProfileKEventAction          10
    com.apple.driver.AppleProfileCallstackAction          20
    com.apple.iokit.IOSurface          74.2
    com.apple.iokit.IOBluetoothSerialManager          2.4.5f3
    com.apple.iokit.IOSerialFamily          10.0.3
    com.apple.driver.AppleHDAHardwareConfigDriver          2.0.5f14
    com.apple.driver.DspFuncLib          2.0.5f14
    com.apple.iokit.IOAudioFamily          1.8.3fc2
    com.apple.kext.OSvKernDSPLib          1.3
    com.apple.iokit.IOFireWireIP          2.0.3
    com.apple.iokit.AppleProfileFamily          41
    com.apple.driver.AppleHDAController          2.0.5f14
    com.apple.iokit.IOHDAFamily          2.0.5f14
    com.apple.iokit.IO80211Family          320.1
    com.apple.iokit.IONetworkingFamily          1.10
    com.apple.driver.AppleSMC          3.1.0d5
    com.apple.driver.IOPlatformPluginFamily          4.7.0a1
    com.apple.driver.AppleSMBusPCI          1.0.10d0
    com.apple.driver.AppleBacklightExpert          1.0.1
    com.apple.iokit.IONDRVSupport          2.2.1
    com.apple.iokit.IOGraphicsFamily          2.2.1
    com.apple.driver.CSRUSBBluetoothHCIController          2.4.5f3
    com.apple.driver.AppleUSBBluetoothHCIController          2.4.5f3
    com.apple.iokit.IOBluetoothFamily          2.4.5f3
    com.apple.driver.AppleUSBMergeNub          4.2.4
    com.apple.iokit.IOUSBHIDDriver          4.2.0
    com.apple.driver.AppleUSBComposite          3.9.0
    com.apple.driver.XsanFilter          402.1
    com.apple.iokit.IOSCSIMultimediaCommandsDevice          2.6.8
    com.apple.iokit.IOBDStorageFamily          1.6
    com.apple.iokit.IODVDStorageFamily          1.6
    com.apple.iokit.IOCDStorageFamily          1.6.1
    com.apple.iokit.IOATAPIProtocolTransport          2.5.1
    com.apple.iokit.IOSCSIArchitectureModelFamily          2.6.8
    com.apple.iokit.IOFireWireFamily          4.2.6
    com.apple.driver.AppleFileSystemDriver          2.0
    com.apple.iokit.IOAHCIFamily          2.0.6
    com.apple.iokit.IOUSBUserClient          4.2.4
    com.apple.iokit.IOUSBFamily          4.2.4
    com.apple.iokit.IOATAFamily          2.5.1
    com.apple.driver.AppleEFIRuntime          1.4.0
    com.apple.iokit.IOHIDFamily          1.6.6
    com.apple.iokit.IOSMBusFamily          1.1
    com.apple.security.TMSafetyNet          6
    com.apple.kext.AppleMatch          1.0.0d1
    com.apple.driver.DiskImages          289
    com.apple.iokit.IOStorageFamily          1.6.3
    com.apple.driver.AppleACPIPlatform          1.3.6
    com.apple.iokit.IOPCIFamily          2.6.5
    com.apple.iokit.IOACPIFamily          1.3.0
    Model: MacBook2,1, BootROM MB21.00A5.B07, 2 processors, Intel Core 2 Duo, 2 GHz, 2 GB, SMC 1.13f3
    Graphics: Intel GMA 950, GMA 950, Built-In, spdisplays_integrated_vram
    Memory Module: global_name
    AirPort: AirPort Extreme, Atheros 5416: 2.1.14.6
    Bluetooth: Version 2.4.5f3, 2 service, 12 devices, 1 incoming serial ports
    Network Service: AirPort, AirPort, en1
    Serial ATA Device: TOSHIBA MK8034GSX, 74,53 GB
    Parallel ATA Device: MATSHITADVD-R   UJ-857D
    USB Device: Built-in iSight, 0x05ac  (Apple Inc.), 0x8501, 0xfd400000 / 2
    USB Device: IR Receiver, 0x05ac  (Apple Inc.), 0x8240, 0x5d200000 / 2
    USB Device: Bluetooth USB Host Controller, 0x05ac  (Apple Inc.), 0x8205, 0x7d100000 / 2
    USB Device: Apple Internal Keyboard / Trackpad, 0x05ac  (Apple Inc.), 0x021a, 0x1d200000 / 2
    Thanks!

    This may help: http://thexlab.com/faqs/kernelpanics.html

  • Problem with sharing internet connecting with Wii via AirPort

    I have an iMac running the latest updates of 10.0.4. My internet is DSL, so it comes into the modem via the phone, and then the modem connects to the iMac via an Ethernet cable. ie: I don't have a wireless network.
    I just bought a Wii and want to connect it to the internet using the built in AirPort feature of the iMac. After I turn on Internet Sharing in Sharing, the Wii will find the iMac as an Access Point (that's the term in the Wii menu).
    The problem I have is that the Wii will not connect to the internet unless I turn off the firewall in OS X. Obviously, this isn't a great solution to getting the Wii connected.
    Does anyone have any idea of how to allow the Wii through the firewall without turning off the firewall.
    Thanks.

    Though this link talks about blocking them, you should be able to reverse it...
    http://www.ist.uwaterloo.ca/security/howto/2007-07-31/
    In the Firewalltab>Advanced, is UDP being blocked? You can also open specific ports.

Maybe you are looking for

  • Two macs to share an iTunes library on Time Capsule?

    what's the best way to do this? all the threads I've seen end up with only one computer able to access the library at a time. what i want is to rate a song upstairs on my G5 and not have to do it again on my iMac downstairs. I have both computers' iT

  • T61 CD/DVD drive won't read or burn CD's

    Recently I have found that my CD/DVD drive does not recognize CD's.  After inserting a disc, the drive spins, makes some noises, but never recognizes a disc.  When I try to open the drive, it searches and an error message appears asking me to insert

  • Recordset per message not working

    Hi All, I got a scenario where i need to read a file of more than 1mb which has got around 6000 records.i want to read 100 records at a time and have mentioned "Recordset per message-100" in the file configuration.But still i am seeing a xml message

  • Smartbar menu not displaying in web mode

    Hi I am running 6i web forms on a Solaris 8 box. I have two forms which are very similar. In client/server mode both show the default&smartbar menu. In web mode on Solaris, one of them does, the other doesn't. I cannot see why they do not show the me

  • My Iphone 3G isn't charging.. :(

    My Iphone 3G does not charge!? I plug it into my charger and it doesnt do anything.. i tried everyone else's charger and the same thing happened so its not my charger. Do i need a new battery..?