LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the VI in LabVIEW using File Open and verify that it is runnable.

When trying to run a sequence on a deployment machine I get this error. When I switch the Adaptor back to the Development System the problem goes away however I do not have the luxury of keeping the full Labview development on the test machine. Is there a know fix for this problem and what is the cause of this error. Here is the software and versions I am using. It seems that the vi's that are broken are using Invoke and Property Nodes within them, I am not sure if this is just a coincidence. It appears it is more related to the invoke node than the property node. Any help is greatly appreciated. Why does it seem everything works great until you try and deploy it on a test machine. This is not the first time I have had these kinds of problems using Nation Instruments software.
Labview 8.2.1
TestStand 4.0
Solved!
Go to Solution.

I have a similar problem.
A bit of background - I had developed a test suite with a Labview front panel for manual operations, and a Teststand project which used some of the same lower level vi's, and specific test step vi's. It was developed on LV 2010 32-bit and Teststand 2010. All was fine.
Recently i had to rebuild my development machine and installed only LV 64-bit 2011 and the latest (2010) Teststand from the 2012 Dev Suite.
I knew that i wanted to run some new hardware drivers in 64-bit versions due to another problem, so i replaced the .dll in the very lowest level VI with the 64 bit version. And ran the manual interface. All ok.
But when i try the Teststand execution, i get one of two errors:
- If i set Teststand to use the LV runtime engine 11.0.1 (2011 SP1), the i get a "Unable to load VI xxxxx with the runtime engine version '11.0'" Despite the fact that each VI does run correctly in LV dev when loaded individually, and i've saved them as version 11.
- If i set it to use the development system (which shows in the config menu 'active version:32-bit' even though 32-bit LV is not installed), then i get the "The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located." error, even though i when i open each VI in the LV 2011 it runs ok.
Any ideas?
How can i set TS dev system to use the 64-bit version? Or is there a separate 64-bit deployemrnt of TS?
Labview 2010, TestStand 2010

Similar Messages

Please help suggestions for solving built-only compiler error: 'The VI is not executable. The full development version of LabView is required tofix this error.'

We have develoepd a software tool and build it on regular basis. It currently runs error free when compiled in the editor, but when we built it and run the executable stand alone we get the error.
'The VI is not executable. The full development version of LabView is required tofix this error.' plus a broeken error.
This menas an compiler error that is not present in the editor but in the stand alone version. We tried to identify errors as suggested in several posts in this forum, but so far unsuccesfull.
As the editor and its compiler do not see the error and are running fine and the stand alone version just syas 'find the error in the editor' in this case LabView is of no help.
Can anyone suggest a sensible or 'good practice ' way of searching for the source of this error?
Our project comprises hundreds of Vis over several libraries.
Thanks,
Chris

Thanks Craig for all your suggestions.
We seem to have located the problem in a new vi just added to the package causing conflicts by using the same vi names as other vis already present in the package. Excluding this vi removed the error.
It seems related to a conflict by having two vis with the same name, which was mentioned by LabView and interactively resolved when running the main vi from the editor. When successfully building the main vi the builder did not mention this conflict and reported a successful build, but when trying to run the executable it gave the cryptic error. The error caused us problems because there was no hint for the cause, just the suggestion to solve this in the editor, while at the same time in the editor the VI was running fine.
We will post about this in detail after we have positively proven that this actually was the case.
The .net version issue was already checked.
Performance was the same on all machines we tested on including the dev machine.
Debugging was tried nut did not help as the vi could not run (broken arrow). We assumed that debugging only helps in running faulty functioning vi''s. We did not check for broken arrows in sub-vis (after connecting), that could have helped, although our application has hundreds of our own vis.
In relation to your remark:
'Are you using many classes? Have you verified that the proper access scopes are set for functions calling those vis?'
Could you elaborate on setting access scopes. We were not aware of this option in LabView, although we realize this is a basic element of the underlying c code.
Ragrds,
Chris

The VI is not executable. The full development version...

"The VI is not executable. The full development version of LabVIEW is required to fix the errors." That is the error I've been dealing with all day. Actually it is repeated 3 to 4 times in the error message, seen when first launching the EXE. Also of note is that the run-arrow is broken. This is in an EXE that was developed well before version 2013, but I recently upgraded it to 2013 to hopefully fix some random LVRT crashes. There is obviously no issue running the code on my development machine, only once it's deployed.
The good news is I've been able to solve the problem (mostly). My EXE now runs without the errors. I found that the problem wasn't actually in the EXE.
We have a separate project with no files, but in the build specification we have the LabVIEW 2013 Run-Time Engine, as well as NI-VISA for serial support. We then bundle the deployment in a self-extracting RAR and it does its business. In the past this has worked just fine, but with LV2013, it seems that there is a component missing from the deployment.
I found that if I download the Run-Time Engine directly from NI.com and run it, the only things I need to install are the Run-Time Engine, and the DEPLOYABLE LICENSE. If I do this, my EXE runs great, but with the custom installer, it is not included for some reason!
Putting aside the fact that I don't know why the Deployable License package is needed (we aren't connecting to remote panels), I can't seem to modify my custom installer to install the Deployable License. There are versions for LabVIEW 2009 and 2011 SP1 in the Additional Installers list, but I don't see 2013.
Can anyone explain why this is??? For now I will just distribute the 257MB Run-Time Engine and the NI-VISA installers separately I guess. But I'd really like to get back to a single, simple package to install all the prerequisites we need. HELP!

iannicholson wrote:
Yes, but then every installer I build will contain the runtime engine. That gets very large very quick. So I have an installer for JUST the runtime engine and VISA runtime.
Just remove them from the "Additional Installers" tab of the Installer dialog.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Error 1003 - The vi is not executable. Simulated DAQ-cards.

Hi all,
I am updating an application written in LabVIEW 7.1 for a customer. The code is not made by my company and is pretty horrendous but it works. I can not develop the code on the machine that it is supposed to run on so I have to do it on my own computer which means that I have to simulate two DAQ-cards that the program needs. I have pretty much finished the program and I want to test if I can build an exe-file. This is where I run in to trouble an get the error message:
Error 1003 occurred at \\Server1\Users\martinh\LabVIEW Data\app\internal.llb\_Main.vi
Possible reason(s):
LabVIEW: The VI is not executable.
I know that this has been discussed at length here and that one has to look out for global variables, dynamically loaded VI:s etc. My question is, does anyone think that the simulated DAQ-cards give me trouble? Do they use some VI:s placed somewhere odd which I need to include when I build the application?
Sincerely
Martin

Hi Martin,
I suggest you try what is suggested in this link, some of the information is already covered in the posts above but some might be new.
http://digital.ni.com/public.nsf/allkb/705C2ECA081F3C7986256C0F00559B02?OpenDocument
If you are using the office toolkit, it might be an idea to masscompile the _office folder and you might also need to uncheck the "Disconnect type definitions and remove unused polymorphic VI instances".
Good Luck
Andreas E
Applications Engineer
National Instruments

The process could not execute 'sp_repldone/sp_replcounters' error for Log Reader Agent and SQL Server Assertion 17066 & 3624 errors in SQL Logs

One of our SQL Server started creating SQLDUMP file and and on investigation I found the error longs are filled with Errors 3624 & 17066. There is transnational replication configured on one of the databases is the LogReader Agent is failing error "The
process could not execute 'sp_repldone/sp_replcounters' on XXXXX".
Not sure if both these Assertion & Logreader Agent errors are related. Before I remove and put the replication, I wanted to check if anyone has experienced the same issues or aware of what the cause.
***********Error messages from SQL Logs******
**Dump thread - spid = 0, EC = 0x0000000111534460
Message
A system assertion check has failed. Check the SQL Server error log for details. Typically, an assertion failure is caused by a software bug or data corruption. To check for database corruption, consider running DBCC CHECKDB. If you agreed to send dumps to
Microsoft during setup, a mini dump will be sent to Microsoft. An update might be available from Microsoft in the latest Service Pack or in a QFE from Technical Support.
Error: 3624, Severity: 20, State: 1.
SQL Server Assertion: File: <logscan.cpp>, line=2123 Failed Assertion = 'UtilDbccIsInsideDbcc () || (m_ProxyLogMgr->GetPru ()->GetStartupState () < RecoveryUnit::Recovered)'. This error may be timing-related. If the error persists after rerunning
the statement, use DBCC CHECKDB to check the database for structural integrity, or restart the server to ensure in-memory data structures are not corrupted.
Error: 17066, Severity: 16, State: 1.
External dump process return code 0x20000001.
External dump process returned no errors.
Thank you in advance.

You need to determine if this error is a transient one or a show stopper one.
It sounds like your log reader agent has crashed and can't continue.
If so your best bet is to call Microsoft CSS and open a support incident.
It also sounds like DBCC CHECKDB was running while the log reader agent crashed.
If you need to get up and running again run sp_replrestart, but then you might find that replicated commands are not picked up. You will need to run a validation to determine if you need to reinitialize the entire publication or a single article.
I have run into errors like this, but they tend to be transient, ie the log reader agent crashes, and on restart it works fine.
looking for a book on SQL Server 2008 Administration?
http://www.amazon.com/Microsoft-Server-2008-Management-Administration/dp/067233044X looking for a book on SQL Server 2008 Full-Text Search?
http://www.amazon.com/Pro-Full-Text-Search-Server-2008/dp/1430215941

When I touch my iPad screen to execute an app, the screen goes dark then the app icon reappears. The app does not execute.

When I touch my iPad screen to execute an app, then the screen goes dark then the app icon reappears. The app does not execute. Any thoughts?

Try a Reset...
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
Basic troubleshooting
From Here
http://www.apple.com/support/ipad/basics/

Error "The application could not execute the required function"

Hi All,
When I try to activate the DTP the following error occurs."the application could not execute the required function".
I was able to activate the DTP for the same DataSource 2 days back but now I am unable to activate .
Kindly suggest what could be the possible reason for the same.
Regards,
Santosh Mani

If you have transformation, check it is active. Is the object 0plant is acitve or not?
Ravi Thotahdri

The Cluster Service function call 'ClusterResourceControl' failed with error code '1008(An attempt was made to reference a token that does not exist.)' while verifying the file path. Verify that your failover cluster is configured properly.

I am experiencing this error with one of our cluster environment. Can anyone help me in this issue.
The Cluster Service function call 'ClusterResourceControl' failed with error code '1008(An attempt was made to reference a token that does not exist.)' while verifying the file path. Verify that your failover cluster is configured properly.
Thanks,
Venu S.
Venugopal S ----------------------------------------------------------- Please click the Mark as Answer button if a post solves your problem!

Hi Venu S,
Based on my research, you might encounter a known issue, please try the hotfix in this KB:
http://support.microsoft.com/kb/928385
Meanwhile since there is less information about this issue, before further investigation, please provide us the following information:
The version of Windows Server you are using
The result of SELECT @@VERSION
The scenario when you get this error
If anything is unclear, please let me know.
Regards,
Tom Li

Hi! I have an iPhone 4S with iOS 6.1.3 and I have iTunes 11.1.3.8. on my Windows 8. Now I can't sync my iPhone, because the device is not recognised by iTunes. Somebody have any idea why, or what can I do (except refresh the iPhone software) ?

Hi! I have an iPhone 4S with iOS 6.1.3 and I have iTunes 11.1.3.8. on my Windows 8. Now I can't sync my iPhone, because the device is not recognised by iTunes. Somebody have any idea why, or what can I do (except refresh the iPhone software) ?

Hi Drazse,
Thanks for visiting Apple Support Communities.
If your iPhone is not recognized by iTunes for Windows, the troubleshooting steps in this article may help:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Cheers,
Jeremy

When I insert a SD card in the side of my Mac it does not open in IPhoto it opens in desktop. it used to open in IPhoto..what gives?

When I insert a SD card in the side of my Mac it does not open in IPhoto it opens in desktop. it used to open in IPhoto..what gives?

Same thing is happening to me but I am using a card reader. Can't get any explanation besides checking the preferences. I can import by downloading to desktop then importing to iphoto but never had to do that before.

I purchased a program on Mac App store and the program does not act as it should, also was required to pay up front whereas had I went to the web site, ibank 4 I would have had 30 days free trial an would have found that the program does not work.?

I purchased a program on Mac App store and the program does not act as it should, also was required to pay up front whereas had I went to the web site, ibank 4 I would have had 30 days free trial an would have found that the program does not work.?

Free trials are not available through the Mac App Store.
Apple is not here. Apple does not answer questions here. This is a user to user support forum. There are only folks here who use Apple products.

When I launch a video from Finder the video is not visible, it's like it's playing on an extended desktop but I can't see the other screen - what is going on?

When I launch a video from Finder the video is not visible, it's like it's playing on an extended desktop but I can't see the other screen - what is going on?

Hi Dan - I'm not sure I know what you mean by 'kick in Expose', can you please explain?
It's a weird one as it doesn't happen all the time. Could it have anything to do with running Apple TV and the MacBook 'thinking' there is another display (extended desktop) and playing the video there?

HT1430 I do a hard reset of my iPhone every so often because I feel it improves performance, but Apple states 'Reset ONLY if the device is not responding'. Forget about my OCD on this, but is their any reason my Apple stresses the ONLY DO THIS if not resp

I do a hard reset of my iPhone every so often because I feel it improves performance, but Apple states 'Reset ONLY if the device is not responding'. Forget about my OCD on this, but is their any reason my Apple stresses the ONLY DO THIS if not responding?

deggie wrote:
Because it is more far-reaching than just turning the phone off and back on, it completely takes out anything in volatile memory, etc. I do reset mine if I notice problems such as no email coming in, text message issues, etc. but the same thing could probably be accomplished by just turning the phone off and on in your case.
Thanks deggie, I think I get it now. Volatile memory (I had to look it up!) is memory that is lost on loss of power, so it's as you say... I'm not achieving anything on a normally functioning iPhone as on-off achieves the same result!... Thanks

I have a new ipad mini an cannot sync it with my aol contacts. Using a pc and when I goto itunes and click on the devices info tab it will not let me click sync contacts it just says "configure"

I have a new ipad mini an cannot sync it with my aol contacts. Using a pc and when I goto itunes and click on the devices info tab it will not let me click sync contacts it just says "configure"

Hi,
See if these Links for Home Sharing add any light to the problem
Understanding
http://support.apple.com/kb/HT3819
Troubleshooting
http://support.apple.com/kb/TS2972
How to
http://support.apple.com/kb/HT2688

The difference using file text and using database ...

whatz 'p dude !!!
yo men i have a little quest bout using file text and
usig database .
the quest is :
if u a programer tell me, if u use file text why u use that ?
whats the advantages using file text for saving record ?
and if u use database like jdbc,sql,orcle for making java
what the advantages using them ?
can u give me some hope plizzzz

if u a programer tell me, if u use file text
why u use that ?Text files are good for storing things like configuration data. For this, you are best served using java.util.Properties to store data in any easily accessible format. That's the problem with text files, you have to invent a format and a way to read/write that format every time you use a text file for a database. Sure you could use a standard format like CSV, but you run into big problems when your database exceeds several megabytes in size. Doing something a simple as reading a single field from a file usually involves reading the entire file. That can kill performance if you have to do it repeatedly and often.
and if u use database like jdbc,sql,orcle for
making java what the advantages using them ?Java was made with C, not with JDBC, SQL, or Oracle. SQL is a language for reading and writing data from a database. JDBC is a Java interface to interact with databases. And Oracle itself is a relational database.
The advantages of using a database are ease of use, performance, and reliability. All you need to know is JDBC and SQL to read/write data from a database (though SQL varies slightly with every different database). Databases use indexes to allow them to quickly find rows and fiels in a database without having to read the entire database. Most of them cache data in memory to speed things up too.
That's it. If you want to know more, search Google or buy a book or two :)
can u give me some hope plizzzzI'm hopeful you will realize that you make yourself look like an idiot typing like that.

LabVIEW: The VI is not executable. Most likely the VI is broken or one of its subVIs cannot be located. Open the VI in LabVIEW using File Open and verify that it is runnable.

Similar Messages

Maybe you are looking for