LCD becomes fuzzy after connects with T61p through VGA port
Hello,
I have a Dell E207WFP LCD which is previously connected to a Dell desktop through VGA. Today I connect it to my T61p through VGA using the same cable. I am able to setup the resolution as native resolution which is 1680*1050 @ 60Hz. However, I found that the screen is obviously fuzzy than connect to the desktop. The font is not sharp. I tried to adjust the cleartype font in Win7 and the bright and contrast in the LCD but nothing helps. I connect it back to the desktop and it works fine... Both computers run Win7. Could you please let me know what could be the possible reason? Thank you very much!
My T61p uses FX 570m video card.
This is hard to judge without a picture. It could just be a low-quality VGA port which is not a defect but an attribute or a nature of many laptop VGA ports.
Remember that the VGA is an analog-type video connector and some sort of blurriness is to be expected, especially at higher resolutions, this is because the GPU processes the image digitally as well as the LCD, but the VGA is analog so the image has to go through 2 conversions.
In conclusion: VGA is great for use in projectors and other devices with resolution no higher than 1280x1024. Above this resolution, defects are likely to appear.
For higher resolutions I'd suggest purchasing the Advanced Mini Dock which features the digital DVI port.
ThinkPad T61p | 15,4 WSXGA+ | Intel Core2Duo T9300 2.5GHz | 4GB CL4 DDR2 RAM | nVidia Quadro FX 570M | Win7 Ultimate x64
Similar Messages
-
Why T430 connect with monitor through VGA can only have 60 fps refreash rate?
I have a T430 and T420.
When I connect the T420 with monitor through VGA, the refreash rate of the monitor can be 75 fps in 1600*900. But When I connect the T430 with the same monitor through VGA, the refresh rate can only be 60 fps, no 75 fps option in the list, Anybody has idea why it works like this?
Thanks very much.Actually, on second thought, does the external monitor show up as "Generic PnP monitor" in Device Manager? Or does it show up as the correct model number?
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen -
Iphone 3 and 4 can't connect with wireless through air port
We purchased a new Time Capsule yesterday to replace one that stopped working. We have been able to get the Air Port/network working for our Mac Books and iPads, but cannot access the wireless network on our iPhones (a 3 and a 4). The wireless connection function on the phones show the network and shows a check mark next to the network, but does not switch to the wireless network from 3G. We tried to 'forget the network' and sign in again, making sure we are on the WPA2. Any other suggestions? Tami
I had this happen to me yesterday. I have a AirPort Extreme and my iPhone was unable to connect to the wireless network.
I tried everything from resetting the network settings on my iPhone, Hardbooting the iPhone, and even changing the wireless password on my Wireless network and restarting the AirPort Extreme. Nothing worked.
However here is my solution:
Hardware restart. I just unplugged the AE waited about 20 seconds and plugged it back in. When it came back up ...My iPhone was able to connect to the network. -
Device button no longer appears in iTunes after connecting with USB cable
Since updating software to OUS 7.0.4 my device buttton no longer appears in the iTunes window after connecting with USB cable
Problem solved. I needed to reinstall my Apple Mobile Driver. I found the solution on this web site.
iOS: Device not recognized in iTunes for Windows http://support.apple.com/kb/YS1538
After I reinstalled the driver, my iPohne immediately synchronized with my computer. -
I have tried everything, but still I can't locate the photos tab in iTunes...I have tried changing the resolution, started iTunes after connecting with the ipad2, nothing seems to work! please advise!
I am also providing you with a screenshot of what appears! I need photos on my iPad2
Message was edited by: anganaYou don't see it on the left-hand side of iTunes - you need to connect and select the iPad on the left-hand side, and then one of the tabs on the right-hand side that you use to select which content to sync to the iPad should be Photos : http://support.apple.com/kb/HT4236
You will need to select and sync all the photos that you want on the iPad together in one go as only the most recent sync remains on the iPad, not including photos in a subsequent sync is how you delete them from it. -
My ipod ejects itself, immediately after connecting with usb cable, before synchronizing could start. What’s wrong?
Have you tried plugging the iPod in with a different USB sync cable to verify the issue is not with the cable? It might not also hurt to connect it to another USB port as well.
Otherwise, try manually placing the iPod into Disk Mode and then connecting it to your PC.
Putting iPod into Disk Mode
B-rock -
I am using I phone 5c after connected with my HP elite book 6930p laptop, (Installed Window 7 32 bit). automatic software driver is not deducting, and display Windows found driver software for your device (MTP USD Device) but encountered an error while attempting to install it.
I did install itunes and update also. but the above problem still same.
Kindly give me solution of it. awaiting.
Regards
Abbas Kadertry it with another computer to check if it shows up
if so
uninstall all apple software
reboot
use regedit to search and remove all itunes keys
reboot
resinstall apple software
if non of that helps then try another cable
if that don't help could be your phones connector is damaged -
Why is atv slow to buffer after connecting with cat5 cable
Why is atv slow to buffer after connecting with cat5 cable
Update on some things I have tried
As I am not sure the cause, I have been reading and trying different things, last thing was to set the interfaces to Duplex Full
I did this on both the Ethernet ports on the routers, and both of the Fast Ethernet ports being used on the switch, but has not changed the speed that PC1 is getting.
Also turned on CEF on both routers -
Password failure after connecting with Desktop software
Hi everyone,
I recently installed the BB desktopsoftware on my MacBook Air and today tried to sync my BB.
My BB is password protected (4 digits) and the Air is also password protected.
Problem is; the desktop software started after connecting with the BB, a password prompt came up and I typed the device password --> wrong password message!!
What did I do wrong?
Should I typ the MacBook password?
Please help !!
I stand to lose a lot of information, as this is my first back-up/sync.
Thanks.Hi everyone,
I recently installed the BB desktopsoftware on my MacBook Air and today tried to sync my BB.
My BB is password protected (4 digits) and the Air is also password protected.
Problem is; the desktop software started after connecting with the BB, a password prompt came up and I typed the device password --> wrong password message!!
What did I do wrong?
Should I typ the MacBook password?
Please help !!
I stand to lose a lot of information, as this is my first back-up/sync.
Thanks. -
HT4623 How to use epson iprint after connected with iPad help
How to use epson iprint after connected with iPad help.
When you open Epson iPrint, you will see the various options of ways to proceed, e.g., Photos (to print photos), Maintenance (for printer maintenance). Scan (to perform scanning).
-
E71x not vibrate after connected with PC Suite
Anyone has the same problem? My E71x purchased 2 days ago does not vibrate while and after connected with PC Suite. I had to turn off and turn it back on to activate the vibrating thing.
Thanksmmm... ill describe the whole situation:
phone has 2 days old
I connected it to the PC
Running PC SUITE
All was functioning normal, i had about half charge
i got a phone call from my gf, when i picked up the call, i disconnected the phone
the line dropped dead. so did the phone
i tried to restart it to no avail
i plugged it to the pc, didnt work
i removed the batter, didnt work
so i connected it to the power cord, and the lights turned on
i disconnected then tried to boot it up, and didnt work
i reconnected the power cord and started it while on external power, and it did start, showing just 1 little bar of battery.
I left it there for about 1hr and removed it, and charge was FULL
i reconnected to PC and im monitoring it and it hasn't discharged
so its weird... <.<
my guess is that unlike HTC or Sony Ericsson phones, the data cable and hte power cable CAN be connected at the SAME TIME. that would be the only explanaition on why it doenst charge up on the USB (but ohter theory of mine is that if i connect it to the PC on file trnasfer mode, it might charge it) -
How to connect my Mac Air 13" to my Philips display with DVI and VGA ports?
How to connect my Mac Air 13" to my Philips display with DVI and VGA ports?
Use a DVI to micro-DVI adapter if you're on an original MacBook Air, and a Mini DisplayPort adapter for a newer one.
(119682) -
Titles made in Premiere become fuzzy after rendering
Is there a setting or button to check in Premiere to prevent titles made in Premiere from loosing the clarity and shapeness they had to becoming fuzzy and out of focus after the video is rendered?
I'm a novice learning Premiere. I assumed the softwear would make the export setting the same as the settings used to make the video sequence. I checked the best quality boxes and in both the rendering and exporting windows, but the text in the titles made with Premiere played back fuzzy. However, all the images I used stayed sharp in playback after rendering and exporting, even text that was already in images I imported in to Premiere stayed sharp in playback after rendering and exporting. What are the best sequence and export settings to use to produce sharp clear titles made in Premiere?
-
Can't connect with modem through e2500 router
I have an old Speedstream 5100 modem hooked to my e2500 router. Everything works well except if for some reason my modem disconnects from ISP I can not log into it through the route to reconnect it. I must plug a direct cable into modem from computer run connect script then plug modem back into router all is fine again.
Any ideas why connecting to modem through router is blocked?
Thnaks,
Al
Solved!
Go to Solution.al_mathews wrote:
My Speedstream only has one Ethernet connection so I didn't realize that it looked like a router to the local network. I changed the mode to bridge on the Speedstream and setup PPoE on e2500 and reconnected to ISP on e2500 setup screen. That may solve the problem of reconnecting since now it is managed on the e2500.
One thing I now see is since I left the modem IP set to 192.168.0.X I can't get to it at all through the e2500. Is that because my DHCP in e2500 is setup with 192.168.1.X IP range so modem isn't addressed in my network? If I hook directly to Speedstream and change IP to 192.168.1.X will it become visible on local network?
You cannot access the modem anymore while you have an active PPPoE connection. For PPPoE the E2500 won't need an IP address from the modem thus it doesn't do DHCP on the WAN port and thus it never sees it. When you try to access 192.168.0.* addresses the E2500 will route it through the PPP tunnel to the ISP.
If you hook your computer directly to the SpeedStream it should automatically pick up a DHCP address (assuming the computer is still running on DHCP and not with a static IP and the SpeedStream does not automatically disable the DHCP server in bridge mode). If you have set up a static IP on the computer you have to change the IP address to a 192.168.0.* address. -
DVI to s-video adapter altering laptop display after connection with TV
Greetings,
I recently got my MacBook Pro to display on my TV via the dvi to s-video adapter (also connected stereo sound). Everything works great, but ... after I disconnect the windows on several of my programs are altered (stretched, shortened, often relocated offscreen or very near off-screen). My ical window refused to display at all. I trashed the ical preference file in the Library, restarted the program and I could see the window again. I'm going to be connecting with my TV a lot. It will be a pain to have to trash preferences files after every connect. Anyone know what's going on?
Thanks,
Sigi
MacBook Pro Mac OS X (10.4.6)
MacBook Pro Mac OS X (10.4.6)What happens if you quit all those applications prior to making the connection to the TV? I would think that should prevent the windows from dynamically resizing. But they are still going to have to resize if you open those apps while connected to the TV.
Mac OS is trying to keep the open windows completely on the desktop. Since your TV's screen is likely much smaller (in pixels) than the 1680 x 1050 pixels of the MBP, the windows are being shrunk and in some cases repositioned so they fit on the desktop when connected to the TV. Unfortunately, the previous settings are forgotten and not restored when you disconnect.
Maybe you are looking for
-
Continuing Bridge Cs6 problems
Have been close to a month now and no Bridge? Have uninstalled CS6 again. How can you do a Beta with half the program. Since the Bridge anomally seems to be happening in Windows and Mac, it would seem someone could figure this out. To recap once
-
Kuler link on main page is pointing to soundbooth application
---> kuler <--- (Nov 21) Quickly explore and get inspired to create and share your own color harmonies.
-
Date field (not required) causing an error...Please assist!
Hello, I am a beginner when it comes to ColdFusion could someone please assist with this issue? I have a date field in my application that is not required, I want users to have the choice to leave this field blank. Below is a breakdown of what I have
-
Cannot See Airport Express in Airport Utility
I've been browsing the other topics, but don't see one with my exact problems. I got an Airport Express for Christmas and was able to get it to work on my parents network; but now that I'm at home, I can't get it to even show in the Airport Utility.
-
why can't I open my pdf file