Learn to drive cd/dvd rom

Hello i am preparing for the arrival of my new macbook but have a question about a learn to drive software package. An example of what i am looking for is:
http://www.amazon.co.uk/Official-Learning-Drive-Pack-PC/dp/0115526102/sr=11-1/qi d=1168002669/ref=sr111/026-9161798-1001226
is there an equivalent for mac's?
Thanks

I did a search a few months ago for another poster, and at that stage, there was no equivalent for Mac OSX. If this Macbook will be your only system, you should look at http://www.parallels.com/ or Bootcamp for running Windows XP on your Macbook and running it under that.
Sorry!

Similar Messages

No hard drive or dvd-rom

Hi Guys,
I have just had a system built for me , which contains the following
MSI Neo 965 Mobo
Intel core duo e6400 conroe 2.13ghx
320gb SATA hard drive
1gb DDR2 800mhz Ram
I have installed my own radeonx1950pro 512mb card and my dvd rom(ide).
When i first turn my pc on at the diagnostic screen where it shows what is connected (ide primary/master ) it has none , i then get two options f1 to continue and del to enter setup. if i press f1 it goes to a screen where it shows my hard drive and dvd-rom , and ask me to hit a ket to continue , when i do i successfully boot into windows , when i goto bios and into boot sequence none of my devices are there , any ideas? the only way to load to windows is if i keep hitting f1. Sorry if this sound a newbie question , but my last pc was all ide and i know nothing about SATA. also i added a memory card reader in to the floppy drive space , when i look at my drives my only hard drive has the letter H , and one of my memory card slots has the drive letter C ?????
Regards
Lennon

sounds like you have a windows that was installed for previous system. You just plugged it in and hope everything work just fine. Right?
On this P965 Neo board, the PATA controller is off to JMicron external controller. So for sure, you need to install the proper driver for this controller. Check on the sticky links on top of this forum table. Get the latest driver and installation instruction there.
Also, make sure your SATA HDD is pluged to the correct port. Which port you're using?
In the BIOS, what did you set for the SATA and PATA? Everything has to be setup properly, refer to your motherboard manual on those settings.

Driver for DVD ROM SD-R1312 Need Help

After moving to another apartment, I've lost my CD Toshiba DVD Driver. Without it I cannot use my DVD anymore. Plz help me. I've searched through the Net and in Toshiba Download Center, but I can't find it.
DVD ROM SD-R1312
Driver can send to:
[email protected]
Thank you very much

Hi,
which Notebook do you own and which system is used?
Normally you don't need an extra DVD driver except DVD RAM is used!
Is there occured any failure with the DVD? Why can't you use it anymore?
Please write down some further informations!
Bye TOK

Driver for DVD rom drive for dv6308nr

Does anyone know where to find the driver for an HP laptop dv6308nr cd/dvd rom drive? I looked it up on the site and it isn't listed under the available drivers. Maybe I am missing it????

Hi,
which Notebook do you own and which system is used?
Normally you don't need an extra DVD driver except DVD RAM is used!
Is there occured any failure with the DVD? Why can't you use it anymore?
Please write down some further informations!
Bye TOK

IDE Harddisk and DVD ROM cannot detected by BIOS in K7N2 Delta Series

Does anyone can help...
I have problem with my system, From now on i cannot use my computer because it cannot started the windows. When i checked to the bios there is no detected Harddisk in IDE 0 ( i have 2 harddisk installed), only 1 detected in IDE 1 - only CDRW drive ( for CDRW drive and DVD ROM drive). I checked the power cable to the both Disk drive and Optical drive there is no problem. If i change the master and slave pin the problem stil happen.
I don't know what to do Please help me.
my system :
MSI K7N2 Delta Series
AMD Athlon XP 1800+
Windows XP Pro SP2

Quote from: ici on 08-February-06, 01:06:02
When problems occur go back to basics. You stated D: is unreadable but C: partition is readable (if I understood right).
As sharp said use only one stick of ram. Remove any additional PCI cards installed other than Video. Do not plug in anything but the hard drive set to master.
Check to see if system will detect.
If at this point it properly detects your drive, check for a boot to windows. If it boots then remove the hard drive and try just the CD-ROM for detection purposes. If this detects try them together again, if they fail to detect you most likely have a power supply issue. And yes, PSU issues can crop up very suddenly.
If this fails take the Hard Drive to a friend and have them test it along with the CD-RW/ROM drives. If they work there and your issue still persists when you have eliminated all other possible points of failure you probably have a bad motherboard.
Sorry i forgot to tell that the harddisk that the D: cannot unreadable is i check it on other system as a slave.
Okay i will try your suggestion.
Thanks for your comment

Mounting a Solaris x86 CD/DVD from a remote Windows CD/DVD-ROM drive

Greetings, all.
Is it possible to mount a remote Windows CD/DVD-ROM drive? I have the Solaris 10x86 Companion Software DVD sitting in a CD/DVD-ROM drive that's installed on a Windows server on my network. It is shared-out (F:) and the two servers can ping each other. I've also confirmed the NFS services/daemons are running on the Solaris x86 machine. I've tried the following variations but, all have failed to produce successful results:
# mount -F nfs x.x.x.x:/f /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F hsfs x.x.x.x:/f /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f
# mount -F hsfs x.x.x.x:/F /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F
[FYI: S10_106_SOFTWARE is the DVD's label as reported by Windows Explorer.]
# mount -F hsfs x.x.x.x:/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/S10_106_SOFTWARE
# mount -F hsfs x.x.x.x:/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/s10_106_software
# mount -F nfs x.x.x.x:/S10_106_SOFTWARE /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F nfs x.x.x.x:/s10_106_software /mnt
nfs mount: x.x.x.x: : RPC: Program not registered
nfs mount: retrying: /mnt
# mount -F hsfs x.x.x.x:/f/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f/s10_106_software
# mount -F hsfs x.x.x.x:/F/s10_106_software /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F/s10_106_software
# mount -F hsfs x.x.x.x:/f/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/f/S10_106_SOFTWARE
# mount -F hsfs x.x.x.x:/F/S10_106_SOFTWARE /mnt
mount: No such device
mount: cannot mount x.x.x.x:/F/S10_106_SOFTWARE
I've also tried mounting it at bootup by adding the appropriate entry in the /etc/vfstab file but, this does not work as well. I've tried Google'ing for an answer to my issue but, I haven't been able to find anything that applies directly to what I'm reporting. It's usually chatter about mounting from one UNIX server to another. Any advice from the community would be greatly appreciated.

After three weeks, you deserve a reply. Windoze does
not natively support NFS.Also deserves a decent answer...
There are two ways to do this:
Install Microsoft's free "Windows Services for UNIX," which includes a Windows NFS server; or
Install the 'sharity' package (google for it); it provides Solaris systems the ability to mount Windows shares

PowerMac G5 doesn't work anymore simply due to a DVD-ROM drive removal!

Hello, here's what's happened (I'll write using the "present" because I'm not English).
This happened about two days ago:
I need to read an Ultra ATA hard disk, so I power off the Mac.
I remove the SuperDrive DVD-ROM and I connect the hard disk in its place (I already made this with other ATA hard disks in past and it always was OK).
I close the Mac.
I try to start: nothing! The light on the power-on button of the Screen (Apple Cinema Display 20" plastic) and the light on the power-on button of the Mac case starts flashing 3 times (then stop, than other three times, etc...).
So I power off. I change the jumper configuration of the hard disk, like the Super Drive. I try again: NOTHING. Always three-times flashing the lights.
So I power off. I re-install the DVD drive, close the Mac again and restart it.
SURPRISE: the same symptom! The computer doesn't start and always makes the three-times flashing lights...
So I tried totally removing the DVD drive, and restarting it without it: nothing: same symptom.
Unfortunately I made these attempts forgetting to disconnect the power cable of the Mac!
Then I start trying with other RAM configurations, hoping that just a RAM module got burned. I have 6 ram modules (512 MB each).
I try lots of combinations... nothing, always same symptom.
Finally, I disconnect the power cord again, I re-install all the RAM modules, an I try to reset the CMOS: I remove the Motherboard battery for some seconds.
Than I re-install the battery, close the Mac, connect the power cord, restart it: it works!!!
I go in System Info, and I see that it doesn't recognize two of the 6 RAM modules: just 4. The slots of the other 2 not recognized DIMM modules seems empty, but there is the ram!
So I power off the Mac Again. I disconnect the power cord.
I change the RAM modules positions. I try again: nothing! Again the three-times flashing lights symptom, and always black screen again.
So I try again by removing the CMOS battery... nothing... always flashing...
After lots of attempts (also changing again the RAM positions, trying to remember how it was when it worked...)... nothing.
I power off the Mac.
After about an hour, I simply try to power on it... IT WORKED!!!
I used it too... went on Internet, etc... Finished working, I powered it off and went to bed.
The day after, I tried to power it on... nothing! Always three times flashing lights...
From that moment, it was totally impossible to let it work...
I tried to change the RAM positions again... I tried also pressing every time the reset button on the Mother Board... nothing...
The only different symptom that I obtained, a couple of times, was that the two lights (on the Screen button and on the Mac tower button) didn't flash, but was always on.... but it didn't run anyway: totally black screen.
How is this possible? Durin 18 years of computer hardware experience, NEVER happened that a computer got broken just removing and re-installing a DVD-ROM drive!
And I'd never imagined that removing a DVD-ROM could be a dangerous operation... It seems to me just like a car that got broken if I replace the cigarette lighter...
What do you think? how is this possible?
If the CPU or the Motherboard or the RAM too got broken... simply it NEVER should run... on the contrary two times it worked very well!... with a broken Motherboard or CPU??? ...mmmm... so strange....
If the RAM got broken... how is this possible? 6 ram modules burned together??? It seems so absurd... (in past there were 8 RAM modules... one or two got broken... so I removed them and it worked again... but not 6 !!!!).
Any opinion?
Any practical advice?
Prevision of costs?
Thank you!!!
Message was edited by: ununpentium

Hi Wolfman I have an update of the situation.
We tried moving the RAM modules again... and at one point it worked! With just 2 RAM modules.
But at the green screen (with the gray apple darker) it blocked.
So we removed the two RAM modules and installed other two modules: it worked again! These two last modules are 512 MB each.
So we restarted the system pressing "c" with the OSX DVD in the drive, and it worked! I used System diagnostic OSX utility and it found the 2 ram modules, but of 256 MB each instead of 512 !!! How is this possible? (if they were broken OK, but detect just half of its size seems so strange...).
Than we restarted it again connecting an OSX bootable external Fire Wire LaCie hard disk (FW400 port), and it worked!
We used DISK UTILITY to test the internal boot hard disk and it gave me an error (verify disk).
The Disk utility was unable to repair the disk.
Another damage!
I remember that in the past attempts it booted once (not three times flashing) and stopped at the grey screen... (I think: maybe due to the boot hard disk error!).
Unfortunately this external bootable firewire disk has got some problem and it sometimes blocks itself emitting a "clic".
So I powered the mac off and connected another newer firewire lacie bootable hard disk. I connected it in the FW800 port. I rebooted and... surprise: three times flashing light again!!!
No way to let it pass this wall, no initial "sound" again... nothing!
So I removed the FW800 drive, and changed the RAM again (inverted them, always two internal slots n. 1 and 2): it worked!
I booted from the FW400 hard disk, and it worked. I was able to backup some data from the internal hard disk (in order to be able to try to solve the error initializing it), and I tried again to boot with the FW800 hard disk (I want a stable system while initializing a drive!).
As I connected the FW800 hard disk again, I tried to reboot... nothing! Again the three-times flashing light error! No sound... black screen again...
(So, simply removing a DVD ROM I got RAM broken, maybe the Logic board, the hard disk too... maybe the FireWire 800 port too.... mmmm.... this mac is possessed! And it is connected through a professional power stabilizer too!).
So after several attempts with RAM, cmos reset, firmware reset (power it up holding the power on button for some seconds), etc... I got it working again...
So this time I rebooted it pressing "c" and I initialized the internal hard disk using the OSX DVD as boot drive...
Then I rebooted from the FW400 hard disk and I used CarbonCopyCloner to restore an internal hard disk clone OSX complete installation from a .dmg image file in the FW800 lacie hard disk... but this time I connected it not using the FW800 port but through the USB 2.0 port... and it was able to copy the data.
The computer was working... able to boot... no three times flashing error... no FW800 connections... always rebooting OK... the internal hard disk initialized, working, with NO errors (disk utility tested), made bootable...
I tried to reboot again (with no "c" or "alt" pressing, hoping the internal boot hard disk working again): nothing!
THREE TIMES FLASHING LIGHT AGAIN!!! No way to solve the problem now... always flashing...
What is happening here??? I don't understand! I use computers (instable DOS/Windows computers mainly!!!) form about 18 years... never seen a so strange behaviour!!!
We'll try to gather money to replace the RAM, before thinking to a Logic Board replacement...
Your opinion?
Thanks!

My acer 7535-5020 no longer recognizes my cd/dvd rom drive

My acer 7535-5020 no longer recognizes my cd/dvd rom drive-I am ready to scream! I cannot afford the tech prices as I am disabled but I cannot find anything to cure this sick puppy. Help please!!!

check inside BIOS whether your ODD can be detected, if cant be detected must be connection cable or HW issue
if still able to detect in BIOS, try to run basic troubleshoot regarding ODD
https://support.microsoft.com/en-us/kb/314060/en-us?wa=wsignin1.0

DVD-Rom drive in Satellite C655-S5128 not working properly in Windows 8

I recently upgraded my system from Windows 7 to Windows 8. However, the DVD-Rom drive after the upgrade no longer works properly -- it now treats the pre-recorded disk as if it was completely blank. I tried reinstalling the Toshiba Disc Creator, but that did not work.
Any solution?

You apparently did not use the Toshiba Upgrade Assistant in upgrading to Windows 8. See HERE for DVD and Disk Creator problems occurring during the upgrade and solutions.
C.B.
Toshiba Sat. C75D-B7260 Win 8.1 64 Bit--Toshiba Sat. L775D-S7132 Win 7 HP SP1 64 Bit and Win 10 PRO Technical Preview--Toshiba Sat. L305-S5921 Win Vista SP2 32 Bit

DVD drive will not read DVD-Roms

I recently tried to reinstall a game that I had played previously, only to find that my drive will not read it. I can hear the disk spinning, but my computer will not recognize that there is a disk in the drive. I tried some of my other games and I noticed that all of the older games, that ran on CD-Rom, had no trouble installing, while the ones that ran on DVD-Rom never showed up in the drive.
This is strange because I have installed all of these DVD-Rom games on my laptop before with no problem. I've tried doing simple fixes, like updating everything and uninstalling then reinstalling the drivers, but nothing helps.

Hi,
If it worked before then try few System Restore points and check. Could have happened due to some update.
Also provide the Product number of your notebook if restore doesnt help.
Note:
If you have HP Support Assistant installed on the computer(The Blue Question Mark) then open it ==> Complete all pending Updates & Tuneups==> Restart and Check. It may solve your problem
Although I am an HP employee, I am speaking for myself and not for HP.
**Click on “Kudos” Star if you think this reply helped** Or Mark it as "Solved" if issue got fixed.

I just installed a new DVD rom/CD-R drive in my G4...I can't install OS!

Hey guys!
A friend recently gave me his G4, but the CD/DVD drive wasn't working, so I went to Best Buy and bought a CDRW/DVD-ROM Combo Drive by "Dynex." I installed it and the tray pops out and it appears to be doing something when I put in the operating system DVD, but the screen blinks a file folder and a question mark.
There is no operating system currently installed.
Are only certain drives compatible with this computer, or is there something I should be doing upon start-up?
Thanks!
Powermac G4

Hey! I Found out the drive I was using was incompatible. I put in a Pioneer drive and it worked great.

Can anyone point me in the right direction for the link to download Acrobat 9 Standard? I found the link to download 9 Pro but not standard. Old computer crashed and new computer does not have a CDR/DVD rom drive.

Can anyone point me in the right direction for the link to download Acrobat 9 Standard. I found the link to download 9 Pro but not standard. Old computer crashed and new computer does not have a CDR/DVD rom drive.

Hi,
Standard or Pro would be licensed through your serial number, the download link and downloaded file would be the same for both of them.
Pro or Standard would be determined after you put in your serial number.
Download Acrobat products | 9, 8
Thank You
Arjun

Dvd-rom drive not working

i got a satellite 1805-S253 model with a toshiba dvd-rom sd-c2502 drive..now when i put a cd or dvd inside the drive..it sounds like its skipping..i check the driver on it and everything is updated..now when i click on the drive i get this message saying windows cannot read from disk the disk might be corrupted,or it could be using a format that is not compatable with windows?

Hi, if it fails with any CD or DVD here some ideas. The skipping or rubbing could mean it's not seating fully on the spindle (Which will let it read). The not reading could be dust on the laser eye (Try some canned air), it could be corrosion on the contacts where the CD/DVD plug's into the motherboard (Remove the drive and inspect, reinsert). I had two M2 combo drives that failed for no apparent reason and I tried the above and nothing. I pulled the drive again and looked at the plug that plugs into the MB and saw two screws in plastic frame around the connector. I took them out and wiggled it and it came off, it turned out to be an adaptor with a smaller connector on the back that plugged in the main part of the drive. I wiggled it back on and put the screws back and tried it and it worked like new on both of them. Who knew?

I need some drivers for my CD-RW/DVD-ROM drive

I have been going through the apple site for a few hours here and I would really like to speak to a human being about this. This is not hard. I have a Pismo PowerBook G3, which I purchased online, used. Wiped the HD when I got it, installed 10.2.8. Updated iTunes to version 6.0.5. I get an error message when I try to burn a CD, missing software or incompatible drive. The drive is an apple brand drive. I am not certain where to find the serial number on it, there are a lot of numbers on it, but it can be provided if someone will tell me where to look. It's not a hardware problem, I can watch DVDs and play CDs, just can't burn. The drive says "CD-RW/DVD-ROM" right on it, and my computer is able to recognize it as such in the system profiler. I am led to believe I am missing a driver(s) that will allow iTunes to burn CDs with the drive.
It'd be great if I could get this on a disc, but if I can just download it from somewhere (willing to pay for it/them!), as long as I can burn it to a disc or download it again if I install a larger HD, that's wonderful. Or, say, I could wait on downloading it until I HAVE upgraded the HD, which I will probably do in the coming year. This would not be as wonderful, but I'm willing to do it.
Please, can somebody help me?

If you can, I'd recommend upgrading to 10.4, as it usually recognizes any 3rd party CDRW/DVD or DVD burner, without the need for Patchburn.
You can check the xlr8yourmac website for reports from Pismo (and other PB) users who have added aftermarket CD/DVD burners to their Pismos, etc.
I too love the Pismo (have had and upgraded at least 10 over the years, some for me and some for family members). The expansion bay was a great idea back in the day. I've found that most if not all aftermarket notebook, a.k.a. "slim" burners fit in the expansion bay. And the Pismo, coupled with Tiger 10.4 (I find 10.4.7 to be outstanding and haven't updated beyond it), is highly usable still today, given that big hard disks and DVD burners and 54g wifi PCMCIA cards (Airport compatible, no drivers needed: e.g. the Motorola WN825G cardbus card) have plummeted in price from a couple years ago. Too bad that compatible RAM is still expensive, as are new Pismo batteries (new, they cost more than many Pismos on eBay!).
As to brands/models, I like the Sony-Nec Optiarc AW-G540A 8x DVD burner (recognized as Master, ID=0 right out of the box, very fast, fairly quiet, priced @ $50-60) because it just works; and the UJ-8xx series DVD burners from Panasonic, which are pretty reliable (and very cheap on ebay if they're older models), because you can swap the faceplate/bezel with the original bezel from the DVD-Rom in your Pismo (if it was a Panasonic model; Apple also used LG drives).
Good luck.

Need CD-RW/DVD-ROM combo drive for Tecra 8200

I have just bought an old Tecra 8200 with a CD-Rom drive in its SelectBay.
I would like to change to a CD-RW/DVD-ROM combo drive.
Could anyone let me know the correct model number for this combo drive please?
Best wishes
Michael

How about this:
*PA3073E-1CD2*
4x CD-R, 4x CD-RW, 24x CD-ROM, 6x DVD-ROM
and it supports this medias:
CD-R (read/write), CD-RW (read,re-write), CD-ROM, DVD-ROM, DVD-R (read only), DVD-RW (read only)
Greetings

Learn to drive cd/dvd rom

Similar Messages

Maybe you are looking for