LI2721s 1 inch border on left, top, and right sides

Hello,
I called tech support but they didn't even seem to know what I was talking about in regards to this monitor, someone will get back to me I was told.
I recently bought this on Amazon, and it looks great, the entire point of me upgrading my monitor was the entire "edgeless" monitor...... but I seem to have a 1.5 inch border (both bezzel, and black bars).  Is this just a fact of the monitor, in which case, it should really be told somewhere in the advertising that this monitor has a 1 inch border.  Orrrrr its a software issue, either or any help is appreciated.
v/r,
Z

Hello Bgriffin2,
As I told you guys in Twitter, IMO this is not a technical problem, this is an advertaising problem. The black border is not part of the LCD panel, its part of the transparent plastic that protects the lcd, but is painted, there are no pixels behind that black border.
Can you guys plug one of these monitors and check this by your self and confirm me and the rest of the customers that this is a mistake in the advertising ?.  PLEASE TRY IT YOURSELF !
I'm copying below some review from Amazon.
"As many others posted, it is no where near edgeless. I've gone under my graphic's card settings and scaled it to 100% vertical and horizontal and still no luck. I looked at the screen under very good lighting and found that the black 2/5 inches from both the left and right edges are not pixels and is colored very well to blend in with the pixel screen."
"I'll weigh in with the "not edgeless" camp. It's actually not edgeless in two ways. 1) there's a 3/16" plastic frame around the entire monitor. It would be easy to look at the product photo and believe the glass goes up to the edge with only a band of plastic across the bottom."
"Secondly there's a 3/8" 5/16" band of dead real estate inside this plastic frame along the sides and top. This band is not apparent when the monitor is off, but when the monitor is on it just doesn't light up. It actually looked to me like i just needed to figure out how to scale the monitor properly, but i searched through all the options and no dice. Plus i verified that the actual live pixels measure 27" diagonally, so this is apparently the way it was intended to look."
"The screen has quite a large annoying bevel. Their description of "The Worlds first edgeless 27" IPS Display" is so massively misleading it's insane, "world first" lol, world's first what?"
"As many others posted, it is no where near edgeless. I've gone under my graphic's card settings and scaled it to 100% vertical and horizontal and still no luck. I looked at the screen under very good lighting and found that the black 2/5 inches from both the left and right edges are not pixels and is colored very well to blend in with the pixel screen."

Similar Messages

  • White border on top and right side on 8.5x11 borderless printing on HP 2710 Photosmart

    I have this printer at home and at work.  At home...I get the problem, at work not.  Exact same printer, using Photoshop CS4 on both.  I have borderless frames, and want borderless photos. 

    Make sure the paper you are using does not have a removeable tab. Also try printing on 5x7 and see if the problem persists.
    I was an HP employee
    If I have helped you solve your issue please mark this post solved.

  • SaveFrameBookAsPdf using FDK11 gets the contents cropped to the top and right of the rendered PDF.

    Hi,
    I am using a method to Save Frame file as PDF using FDK 11 and this works fine. Currently, I have a requirement to Save the whole Frame book as PDF for which i am trying with the same method but the output is not accurate. The contents in the rendered PDF is cropped to the Top and Right. Tried several options and could not figure out the cause of the issue. any help would be highly appreciated.
    Used Method:
               long SaveAsPdf(char* strSourceFileName, char* strTargetFileName)
                    F_PropValsT params, *returnParams = NULL;
                    F_ObjHandleT docId, pgfId, saveId;
                    IntT i = 0;
                    StringT name = NULL;
                    StringT str_Target_File_Name;
                    long bookId;
                    str_Target_File_Name = F_StrCopyString((StringT)strTargetFileName);  
                    F_FdeInit();
                    /* Open all files */
                    bookId = openBookFiles(strSourceFileName);
                    /* Get docId in order to set Acrobat Bookmark levels */
                    docId = F_ApiGetId(FV_SessionId, FV_SessionId, FP_FirstOpenDoc);
                    /* Sets the save parameters so as to save as PDF and allow user to name file.*/
                    params = F_ApiGetSaveDefaultParams();
                    i = F_ApiGetPropIndex(&params, FS_FileType);
                    params.val[i].propVal.u.ival = FV_SaveFmtPdf;
                    /* Saves the book and all its components to one PDF file */
                    saveId = F_ApiSave(bookId, str_Target_File_Name, &params, &returnParams);
                    /* Close the open files.*/
                    while (docId)
                        F_ApiClose(docId, FF_CLOSE_MODIFIED);
                        docId = F_ApiGetId(FV_SessionId, FV_SessionId, FP_NextOpenDocInSession);
                    F_ApiDeallocatePropVals(&params);
                    F_ApiDeallocatePropVals(returnParams);
                    return (long)saveId;
                long openBookFiles(char* strSourceFileName)
                    IntT i = 0;
                    F_PropValsT script, *returnp = NULL;
                    F_ObjHandleT compId;
                    F_ObjHandleT docId;
                    StringT compName = NULL;
                    StringT str_Source_File_Name;
                    str_Source_File_Name = F_StrCopyString((StringT)strSourceFileName);  
                    /* create open script which minimizes user response*/
                    script = F_ApiGetOpenDefaultParams();
                    i = F_ApiGetPropIndex(&script, FS_MakeVisible);
                    script.val[i].propVal.u.ival = False;
                    i = F_ApiGetPropIndex(&script, FS_RefFileNotFound);
                    script.val[i].propVal.u.ival = FV_AllowAllRefFilesUnFindable;
                    i = F_ApiGetPropIndex(&script, FS_FileIsOldVersion);
                    script.val[i].propVal.u.ival = FV_DoOK;
                    i = F_ApiGetPropIndex(&script, FS_FontChangedMetric);
                    script.val[i].propVal.u.ival = FV_DoOK;
                    i = F_ApiGetPropIndex(&script, FS_FontNotFoundInCatalog);
                    script.val[i].propVal.u.ival = FV_DoOK;
                    i = F_ApiGetPropIndex(&script, FS_FontNotFoundInDoc);
                    script.val[i].propVal.u.ival = FV_DoOK;
                    i = F_ApiGetPropIndex(&script, FS_LanguageNotAvailable);
                    script.val[i].propVal.u.ival = FV_DoOK;
                    i = F_ApiGetPropIndex(&script, FS_LockCantBeReset);
                    script.val[i].propVal.u.ival = FV_DoOK;
                    i = F_ApiGetPropIndex(&script, FS_UpdateTextReferences);
                    script.val[i].propVal.u.ival = FV_DoNo;
                    i = F_ApiGetPropIndex(&script, FS_UpdateXRefs);
                    script.val[i].propVal.u.ival = FV_DoNo;
                    i = F_ApiGetPropIndex(&script, FS_UseAutoSaveFile);
                    script.val[i].propVal.u.ival = FV_DoNo;
                    i = F_ApiGetPropIndex(&script, FS_UseRecoverFile);
                    script.val[i].propVal.u.ival = FV_DoNo;
                    i = F_ApiGetPropIndex(&script, FS_AlertUserAboutFailure);
                    script.val[i].propVal.u.ival = False;
                    i = F_ApiGetPropIndex(&script, FS_BeefyDoc);
                    script.val[i].propVal.u.ival = FV_DoOK;
                    i = F_ApiGetPropIndex(&script, FS_FileIsInUse);
                    script.val[i].propVal.u.ival = FV_OpenViewOnly;
                    i = F_ApiGetPropIndex(&script, FS_FileIsStructured);
                    script.val[i].propVal.u.ival = FV_OpenViewOnly;
                    i = F_ApiGetPropIndex(&script, FS_OpenFileNotWritable);
                    script.val[i].propVal.u.ival = FV_DoOK;
                    long bookId = F_ApiOpen(str_Source_File_Name, &script, &returnp);
                    F_ApiDeallocatePropVals(&script);
                    return long(bookId);

    Here's a clip:
    http://depositfiles.com/files/xqqnadc88
    This clip is made up of two clips on top of one another, Video 1 has a 50% right crop and Video 2 has a 50% left crop.  Video 2 crossfades into a clip of the scene with no actors in it which also has a 50% left crop.  I have had this issue on footage shot with two different cameras, one a Sony HD camcorder and the other a little Fujifilm point and shoot still camera with HD video capabilities.  Perhaps "randomly" is the wrong word to use though because I have tried recreating this and other scenes from scratch a few times and I always have the same problem with the right side of the screen disappearing at the same time no matter what I do.  In the project I am working on, I have several scenes where this effect is needed and some of the footage seems to work fine while other scenes consistently give me this issue.
    I also just remembered that I have CS4 (but CS3 runs a little better on my computer) so I'll try putting the clip together in CS4 and see if it still does the same thing.

  • Left and right side of screen does not register mouse clicks.

    The left and right side of my screen (when maximized) does not register a mouse click. I would estimate about 10 to 15 pixels in (top to bottom) before a button will register a click.
    If I work with in firefox not maximized everything works fine. As it stands I have had to add buttons to the left and right side of my Firefox navigation area to utilize the back and home button. I am also not able to use my scroll bar do to this situation with out connecting an external mouse.
    Operating system: Windows 7 Professional (64bit)
    Resolution 1280x800
    Computer: HP TouchSmart tm2 (1070us series)
    This laptop does have the touchpad type mouse, I do not think this is the problem though as it will work if firefox is not maximized.
    Assistance with this would be appreciated. I Love firefox but this is to much of an annoyance to deal with continually.

    Not sure if its ever overheated... I've never left it in a hot car if thats what you mean. Sometimes it gets very hot if I'm using EDGE for a while. I don't push hard which is why I don't think I caused it...
    I will bring it in this weekend and see what they say.
    I also think that the speakerphone sounds fuzzy and muffled a lot more than it did when I first bought it. So just another reason to bring it in.

  • Display resolution is different left and right sides

    Hi, my HP G42 laptop now has a different display resolution on the left and right sides. The left half seems to have less resolution than the right side, the right side looks like it's in HD, the left side looks washed out. I'm not sure if it is a hardware issue or a setting/software issue. The first time it appeared was after a windows 7 update was completed and installed, I'm not sure if that was just a coincidence. Any suggestions would be greatly appreciated. It works but is very annoying to look at.
    Thank you,
    Ray

    Hi Ray_M,
    Welcome to the HP Forums! I see that you are having a problem with two different resolutions on each half of your screen. The easiest way to determine where the problem lies is to connect it to an external monitor. If the image is normal then we know it is an issue with the display screen but if the issue occurs on the external monitor then we know it is a problem with the drivers or the video card itself.
    What is the product number for your g42? There are a number of different models in that series.
    Please click “Accept as Solution ” if you feel my post solved your issue.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Thank you,
    BHK6
    I work on behalf of HP

  • It it possible to have info on the left and right sides of iweb templates?

    When I look at my iweb website there is empty space on the left and right sides of my screen. I was wondering if this space could be used at all?

    Hi
    You can increase the width of your Page, go into Inspector, Page Tab. From here you can adjust the Content Width, which is the width of your page, the bits that you see on the left and right are fillers, for people who's browsers are set bigger than your site. You can change the color that shows by changing the Browser Background.
    In the good 'ole days, most people had screens that were only 800 W x 600 H, but these days most people have at least 1024 W x 768 H (some do, no doubt still have 800x600). So, 1024 is really the max width you can go, dont forget that you need to leave some space for the browser as well, and the scroll bars.
    But pages this big are wider than normal, the best thing to do is experiment and see what works for you.
    Will
    1GHz G4, 15" PowerBook, Airport Network, 1G iPod Mini   Mac OS X (10.4.6)   www.willg4pb.com for iWeb tips

  • IPad2: After upgrad to iOS 8, video output lost left and right side

    I have a cable for my iPad2, once plugged in the bottom slot, it outputs video to TV Component port and audio to my amplifier. It's been working for years. After iOS 8 upgrade, I notice the video output lost left and right side. It's like
    [before iOS 8]     Apple iPad is a wonderful product for me.
    [after upgrade]             iPad is a wonderful product
    The "Apple" on the left, and "for me." on the right of screen is gone in output.

    Change your Aspect Ratio on your TV to 16:9

  • How do I get page numbers on the left and right side of the page?

    I am finishing up a book in PAGES '08 on my Mac.
    How do I get page numbers on the left and right side of the page.
    I can get them on the page but I'd like them on the left and right sides.
    Evan

    If the icons are from dmg files that were used to install 3rd party apps like this one for VueScan
    Control (right) - click on the open dmg icon and select "Eject  xxxx" from the contextual window.
    Then find the actual dmg file associated with those icons
    and drag to the Trash in the Dock and empty.

  • Opened a .ai file, found that left and right side are cut off (landscape vs. regular the issue?)

    Information all in the title.  I open a .ai file and the left and right sides of the image are cut-off based on the "page" box

    Did you open it in a lower version?
    It looks like you opened the PDF part of the file instead of the AI part.

  • Left pane and right pane(Multiple Panes/Multiple Views) in single FACET

    Hi All,
      Please suggest how can we add left pane and right pane(Multiple Panes/Multiple Views) in single FACET , Do we need to create mutiple custom BO's or single custom BO is enough.    Is it feasible requirement to place mutilple panes/views in a single FACET.   Please suggest. 
    Thanks in advance.
    Tim

    Hi,
       Use Back Satement for that.
    ex.
    DATA:  TOWN(10)      VALUE 'New York',
           CUSTOMER1(10) VALUE 'Charly',
           CUSTOMER2(10) VALUE 'Sam',
           SALES1 TYPE I VALUE 1100,
           SALES2 TYPE I VALUE 2200.
    RESERVE 2 LINES.
    WRITE:  TOWN, CUSTOMER1,
          /       CUSTOMER2 UNDER CUSTOMER1.
    BACK.
    WRITE: 50 SALES1,
           /  SALES2 UNDER SALES1.
    Reagrds,
    prashant

  • Move to previous or next magnified photo     Press Left Arrow and Right Arrow keys does not work

    Move to previous or next magnified photo
    Press Left Arrow and Right Arrow keys
    This command no longer works in iPhoto. The photo just bounces for a moment, then all the photos begin scrolling. I used to be able to just hit the key to scroll one at a time.

    What version of iPhoto and system are you running?  What mode are you in, edit, full view, full screen, ???
    OT

  • Missing left and right sides of movies

    Why am I not seeing the full left and right sides of movies, converted using instant handbrake, during playback in itunes or on ipod touch and classic?

    On the iPod touch, to show the whole video, double touch the screen while it's playing.
    As for the other iPod and iTunes, I don't know.
    -Messymeese
    P.S.
    If the iPod touch thing that I said doesn't work, then I don't know what to do.
    Actually, did you happen to mess with the cropping settings while using hadbrake?

  • Role of left input and right input in merge join

    Hi All
    I really appreciate if someone explain me the difference between left input and right input in Merge Join.

    Think it in terms of transact sql join statement. The left input and right input represents the left and right part of join operation. So depending on type of operation chosen like LEFT JOIN,INNER JOIN etc it takes correspondig input as the base input and
    does join operation with the other input. Also it relies upon order of records in input which is why its essential that data should be sorted and also Issorted property must be tru for both the inputs.
    The real significance of choice is for left join as it will take left input as base table and does the comparison with other input returning all records from base input irrespective of whether or not it found a match. In all other cases (INNER/FULL JOIN)
    it gives similar output regardless of the which input you choose as left or right input.
    Please Mark This As Answer if it helps to solve the issue Visakh ---------------------------- http://visakhm.blogspot.com/ https://www.facebook.com/VmBlogs

  • All of a sudden my screen has black bars on both the left and right sides; all of my folders are overlapping as well.  Anyone know how to fix this?

    All of a sudden my screen has black bars on both the left and right sides; all of my folders are overlapping as well.  Anyone know how to fix this?

    Did you try restart the Mac?

  • How to fill up my laptop screen with Firefox horizontally as it currently has a 3" margin on the left and right sides?tly has a

    I just purchased a 17.3" screened-laptop using MS Outlook and Explorer 9 Browser. I cannot use Firefox as my default Browser because I cannot get Firefox to fill up my screen.When I open up Firefox, it maintains a large 3" margin on the left and right sides which does not exist when I open up Explorer 9. Increasing the font size only increases the text size vertically but does nothing to decrease the margin size horizontally.

    You can use this extension to set a default font size and page zoom on web pages:
    *Default FullZoom Level: https://addons.mozilla.org/firefox/addon/default-fullzoom-level/

Maybe you are looking for

  • Issue in PO Version Management

    We have recently configured release strategy for PO in SAP. Now there is issue with Version management. Consider X and Y are users responsible for Purchasing activities. Scenario prior to Release Strategy Configuration: If X has created PO and if it

  • Windows Phone 8.1 "Can't Install Company App" Error

    I'm using VS2013 Update4 to build a Windows Phone 8.1 application.  I can deploy the app from Visual Studio with no problem.  My developer phone is unlocked.   My company has a certificate from Symantec.  I have the pfx file.  We don't want to use th

  • Count of a query in Unix environment and use sysdate

    hi, i have a code below and i want this to be used in Unix env and i need to use sysdate where i hard coded the date but the time should remain as it is. select count(type),type from ebizp.bchistevent where (type = 'com.avolent.apps.event.LoginEvent'

  • Help errors ATI radeon hd 4550

    error: the catalyst control center is not supported bu the driver version of your enabled graphics adapter. please update your AMD graphics driver, or enable your amd adapter using the displays manager. <- this messenger my computer.  i try any time

  • Put scanned text on "fresh" white page?

    Hi! First of all, nice to be here and now for my first post: In ABBY Finereader 11 that I tried before going for Adobe Acrobat X Pro (10) it had a feature that after it had scanned the document it automatically took the text and put it on nice "clean