Limitation on Client VPN for RV220W?

Is there a limitation on using the Client VPN to connect to the RV220W from the same location (site)?
Here’s what happened: One of our RV220W’s went down and we UPS’d it back to Cisco for replacement; so that was the end of our site-to-site connection. I ran to Staples and brought a $200 Netgear R6300v2 Smart WiFi Router, thinking it would be a nice "backup" router should a Cisco router go down in the future again, and also at the $200 price poing and being the "newest" model out, it would have what I need. What I didn’t know is the Netgear R6300v2 is a "consumer" router with no VPN capabilities, so it can not establish a site-to-site VPN connection. So, I figure a cool work around was to have each workstation connect to the other RV220W at the other location. But...I’m finding out that when one workstation is connected, no other workstation can connect: it times out during verification. When I disconnect the workstation that is connected, then another workstation can connect through the Client VPN.
Does this one-at-a-time connection only happen ‘cause we’re all at the same location, trying to connect from the same WAN IP address, in essence the same site?
If so, what would happen if two or more employees wanted to use the Client VPN from the same Starbuck’s location? Would they NOT be allowed to connect at the same time? The first one would connect, and the second one would not connect?

Hi Waverly,
As I understand it, the QuickVPN routers can only accept a single connection at a time from the same remote WAN IP. You *may be able to make another connection by using port 60443 on the second client.
You can also use PPTP and/or SSL VPN on the RV220W. Clearly the best option is a site to site tunnel for multiple users. The RV180(W) might be a better choice for a backup router as it has nearly all of the capabilities of the RV220W at less cost.
- Marty

Similar Messages

  • Configuring Netgear FVS318 VPN for iPhone and Mac OS X clients.

    Hi,
              I am trying to configure the FVS318 VPN for iPhone and Mac clients to connect to. I have been able to set it up that all hard wired and wireless connections with in the network to connect seemlessly, but when it comes to VPN I am not able to get any connection from outside the network. I have set all the usernames, passwords and shared secrets multiple times and I am unable to connect even after reseting it. Any help setting this would be great.
    Thanks

    Are you using your external IP address to set this up? This works while on the network, as in at the office but not from any connection outside? What IP scheme are you using on the Netgear? If you are using something like 192.168.1.1 and starbucks uses the same scheme it wont work. Try setting your Netgear to something like 192.168.33.1

  • What is the VPN for Macbook pro?

    hi what is the VPN for Macbook pro?

    There are several VPN clients that work on the Macbook Pro. https://www.google.com/search?q=vpn+client+macbook+pro

  • Cisco 2504 WLC client VPN Access

    Hi,
    I was reading couple of posts related to Cisco WLC + Client VPN passthrough .. and got  a query.
    https://supportforums.cisco.com/thread/2183687
    https://supportforums.cisco.com/thread/2219356
    The second link says that "Remote Acces VPN connections through the WLC work out of the box". Is this True? No need to configure Layer 3 VPN-Pass though for the SSID?
    They are using WPA2+PSK as Layer 2 Security. Here WPA2-PSK + VPN Passthrough is the right combination for WLAN Layer2 + Layer 3 Security?
    Thanks,
    Jagan

    It works out of the box... you don't need to configure any passthrough.. just connect to the ssid and VPN away.
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • How to install IPSec Client Certificate for Apple products (iPad,iPhoe and Mac)

    We need  Ipsec vpn client authentication with certificate (instead of pre-shared key). We tested the same with Windows client and its works fine. However when we used the same certificates with Apple products (iPad, iPhoe and Mac) it doesnt work.
    We have two types of certificates installed on the client from the CA server.
    One is the root certificate with the extenstion .cer
    and the other one is client certificate with the extension of .pfx (personal informaiton exchange)
    We can not find a proper document to install certificates and client configuration for iPad,iPhoe and Mac. We need to know what type of certificates needed, what are the certificate formats and how to install etc.
    Appreciate if someone has implemented this and share any documents.
    thanks

    This will be helpful for you :-
    http://images.apple.com/iphone/business/docs/iOS_Certificates_Mar12.pdf
    Manish

  • Pix 501 and Client VPN's

    Hi, I've had this 501 for several months now and really stuggled to get the client VPN side working.
    I can get site to site working with no problems using the wizard but the Client VPN never works.
    Latest i've set it up for pptp which I can get the client to connect with no problems but fails to get any traffic from the pix - I can however ping the remote PC from a PC behind the PIX.
    I'm setting these up by the PDM buy i've attached a copy of the config anyway.
    Best,
    Chris

    Hi Kamal.
    It didnt like the command
    nat (inside) 0 access0list nonat
    I can attach via Cisco VPN Client but the same occurs - I can ping the remote from the network - but not the other way round.
    Config attached. - Best, Chris
    : Written by enable_15 at 02:14:05.990 UTC Mon Feb 12 2007
    PIX Version 6.3(5)
    interface ethernet0 auto
    interface ethernet1 100full
    nameif ethernet0 outside security0
    nameif ethernet1 inside security100
    enable password xxx
    passwd xxx
    hostname pixfirewall
    domain-name ciscopix.com
    fixup protocol dns maximum-length 512
    fixup protocol ftp 21
    fixup protocol h323 h225 1720
    fixup protocol h323 ras 1718-1719
    fixup protocol http 80
    fixup protocol rsh 514
    fixup protocol rtsp 554
    fixup protocol sip 5060
    fixup protocol sip udp 5060
    fixup protocol skinny 2000
    fixup protocol smtp 25
    fixup protocol sqlnet 1521
    fixup protocol tftp 69
    names
    access-list nonat permit ip 192.168.1.0 255.255.255.0 192.168.10.0 255.255.255.0
    access-list outside_cryptomap_dyn_20 permit ip any 10.10.10.0 255.255.255.240
    access-list split permit ip 192.168.1.0 255.255.255.0 any
    pager lines 24
    mtu outside 1500
    mtu inside 1500
    ip address outside 213.x.146.72 255.255.x.0
    ip address inside 192.168.1.1 255.255.255.0
    ip audit info action alarm
    ip audit attack action alarm
    ip local pool vpnpool 10.10.10.1-10.10.10.10
    pdm logging informational 100
    pdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 1 0.0.0.0 0.0.0.0 0 0
    route outside 0.0.0.0 0.0.0.x.249.x.65 1
    timeout xlate 0:05:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
    timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
    timeout sip-disconnect 0:02:00 sip-invite 0:03:00
    timeout uauth 0:05:00 absolute
    aaa-server TACACS+ protocol tacacs+
    aaa-server TACACS+ max-failed-attempts 3
    aaa-server TACACS+ deadtime 10
    aaa-server RADIUS protocol radius
    aaa-server RADIUS max-failed-attempts 3
    aaa-server RADIUS deadtime 10
    aaa-server LOCAL protocol local
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server community public
    no snmp-server enable traps
    floodguard enable
    sysopt connection permit-ipsec
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec transform-set myset esp-des esp-md5-hmac
    crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20
    crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5
    crypto dynamic-map cisco 1 set transform-set myset
    crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
    crypto map outside_map client authentication LOCAL
    crypto map dyn-map 20 ipsec-isakmp dynamic cisco
    crypto map dyn-map interface outside
    isakmp enable outside
    isakmp nat-traversal 20
    isakmp policy 10 authentication pre-share
    isakmp policy 10 encryption 3des
    isakmp policy 10 hash md5
    isakmp policy 10 group 1
    isakmp policy 10 lifetime 86400
    isakmp policy 20 authentication pre-share
    isakmp policy 20 encryption 3des
    isakmp policy 20 hash md5
    isakmp policy 20 group 2
    isakmp policy 20 lifetime 86400
    vpngroup vpn address-pool vpnpool
    vpngroup vpn dns-server 192.168.1.1
    vpngroup vpn idle-time 1800
    vpngroup vpn password 634083
    vpngroup VPNclient split-tunnel split
    vpngroup VPNclient idle-time 1800
    vpngroup VPNclient password ******
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcpd address 192.168.1.2-192.168.1.33 inside
    dhcpd dns 89.238.129.211
    dhcpd lease 3600
    dhcpd ping_timeout 750
    dhcpd auto_config outside
    dhcpd enable inside
    username chris password 9DgK/T8KJkq.BhX6 encrypted privilege 15
    terminal width 80
    Cryptochecksum:xxx
    : end

  • Cuantos Clientes VPN soporta el cisco rv042g?

    Quisiera saber cuantos clientes VPN conectados simultáneamente soporta el cisco rv042g, ya que necesito conectar 10 clientes, pero al conectar 3 simultáneos se vuelve inestable la conexión y automáticamente desconecta a un cliente.

    Muy buenos dias, 
    Siento mucho que este tendiendo problemas con la conexión VPN en este router.
    La respuesta a su pregunta es la siguiente\
    VPN 
     QuickVPN 
     50 QuickVPN tunnels for remote client access 
     PPTP 
     5 PPTP tunnels for remote access
    De cualquier manera, no debería de tener problemas si solo esta usando 3.
    Diganos por favor que tipo de conexión VPN esta usando, cual es la velocidad de descarga y subida de su conexión de internet y si puede dar mas information acerca de su problema en especifico, eso nos puede ayudar a ver que opciones hay disponibles.

  • OS X Server VPN and OS X Client VPN Kerberos issue

    I set up OS X Server Leopard at home. I configured VPN on the server. I opened all of the recommended ports and then some.
    I've added the OS X Server to Directory Utility on my OS X client. I've configured a System Preferences > Network > VPN for the connection. I set it up for L2TP using the external address for my server at home, my username in Open Directory, and selected Kerberos for authentication. When I try to connect with the OS X VPN client it asks me to authenticate to [email protected] not [email protected]
    Does anyone have any idea where I should look to see why my OS X Client VPN Client is not trying to authenticate me using Kerberos to my home server but rather choosing my home username and my work Open Directory server? I looked on the forums but I don't see anyone describing this problem with VPN and Kerberos.
    Thanks in advance

    Brandon Macinnis wrote:
    Dnar,
    Thanks for the follow up bit about using the smbutil statshares command.  I used that and could confirm that I am also able to force it to connect with smb2.  Oddly though, in the stat share info it still says "AUTO_NEGOTIATE"
                                  SMB_NEGOTIATE                 AUTO_NEGOTIATE
                                  SMB_VERSION                   SMB_2.1
    But maybe that just means something else and not the fact that it did not auto negotiate to SMB.  I guess for now this will be what I have to do to use smb2.
    I think in this case the AUTO_NEGOTIATE merely means it will auto negotiate a connection between SMB1, SMB2, and (from your data) also SMB2.1 this would have nothing to do with auto negotiating between SMB2 and AFP, which from this thread appears broken.
    I also would like to thank Brandon for the tip about smbutil statshares, I had been looking for a simple way to tell what version of SMB was being used to test my NAS.
    For everyone's benefit, it would appear from the above that whilst Apple advertise Mavericks as using SMB2 they have gone as far as implementing SMB2.1 and merely list it only as SMB2 for simplicity and due to the fact there is not a huge different between SMB2 and SMB2.1
    See http://en.wikipedia.org/wiki/Server_Message_Block#SMB_2_and_3

  • Setting up PIX515E VPN for two networks

    Hello,
    We have a PIX515E and I want to set it up so it can serve client VPN connections for a network on the inside interface and also for a network on the dmz interface.
    On a client machine we set up the ip address of the PIX in a VPN connection and the user can log on using credentials and domain. Now the PIX has to look up credentials using RADIUS, but some users are known on domain A (inside interface) and some users are known on domain B (dmz interface). Domain B is completely different and uses other internal ip addresses, dns servers, ip pool etc.
    Already I have set up VPN for the inside interface and that was easy and it works ok.
    But can I create such a configuration? We only have one DSL line and we want both networks (domain A 192.168.1.x and domain B 192.168.10.x) to go through this PIX.
    Your help is more than appreciated!
    Regards,
    Frank

    rob,
    i don't know your budget requirements, but here is a relatively easy solution:
    http://www.apple.com/server/macosx/features/networkingvpn.html
    and here is an OSS solution that will take a bit more work (but should run on an older box with bsd, linux, or os x running on it):
    http://openvpn.net/
    cheers,
    b

  • Use client VPN tunnel to traverse LAN-to-LAN tunnel

    I've been troubleshooting a problem and can't get over a hurdle. The ASA is running ASA running 7.2(1)24 code. I'm trying to use a client VPN tunnel to connect to the ASA. The ASA already has a LAN-to-LAN tunnel set up and functioning, and I need the client VPN to access the remote site over the LAN-to-LAN tunnel.
    The internal IP address of the local side is 192.168.0.0/24 and the IP of the remote LAN-to-LAN tunnel is 172.20.1.0/24. The clients are handed out 192.168.200.0/24 IPs. I've attached the relevant configuration for the ASA.
    When the client VPNs into the network, I can access the resources on the ASA's internal network. Users on the ASA's internal network can access resources across the LAN-to-LAN tunnel. Client VPNs cannot access resources over the LAN-to-LAN tunnel. For the latter, there are no hits on the C-TEST access list.
    Thank you for your assistance.

    try adding...
    same-security-traffic permit intra-interface
    http://www.cisco.com/en/US/products/ps6120/products_configuration_guide_chapter09186a00806370f2.html#wp1042114

  • Create client vpn package before or after upload root certificate

    Hi everyone,
    I am building funtion create client vpn package base on os bit (64 or 32) to connect point to site of azure virtual network
    I want to ask somebody 
    Create client vpn package before or after upload root certificate?
    If i upload root certificate, funtion return error 404
    if i do not upload root certificate and run funtion generate
    funtion return status code is accept
    correct resuft follows msdn is created
    althought request body is correct
    ResponseUri = {https://management.core.windows.net/29976d9e-898b-46ab-9f80-6238b4f1725e/services/networking/quyen_network/gateway/vpnclientpackage}
    <VpnClientParameters>
    <ProcessorArchitecture>Amd64</ProcessorArchitecture>
    </VpnClientParameters>Thanks for you supports,Hoa Nguyen

    Hi Hoa Nguyen,
    I'm assuming you are creating a Point-to-Site VPN Connection, for which the steps would be:
    Configure a Virtual Network and a Dynamic Routing Gateway.
    Create your Certificates.
    Configure your VPN Clients.
    So to answer your question, you would upload the root certificate before you create the client VPN Package.
    You could refer the following link for details:
    https://msdn.microsoft.com/en-us/library/azure/dn133792.aspx
    Would you be able to provide us the complete error message you get when you upload the root certificate?
    Regards,
    Malar.

  • WRVS4400N v2: Need help setting up VPN for Mac

    I'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
    The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.
    The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.
    We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.
    At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems.
    I have tried just about everything I can think of but have not been able to get this to work. Can someone please help with setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
    TIA

    Hi,
    If you need to establish a client vpn connection with the WRVS4400N, first you need to insure that the modem infront support IPSec Passthrough and that UDP ports 500 and 4500 are forwarded to the WAN IP of WRVS4400N.
    On WRVS4400N you have to configure IPSec VPN tunnel, and when configuring IPSecuritas insure that you have the same encryption as on the router.
    It could help if you enable the Local logs and see the error message.
    You can provide the log output and print screens of the IPSec configuration, also screenshot of configuration of IPsecuritas

  • VPN for xbox 360

    I have an airport express that transmits my wifi signal to my macbook pro and my xbox. I'd like the signal to be VPN protected. I have a hideipvpn account which works fine on my macbook. But the moment I try to transmit it to the xbox it fails. The internet just gets blocked. Is there a way to enter a VPN setting into the airport express itself so that all devices connecting to the signal are getting a VPN protected signal?

    Simple answer: no, you can't have the Airport do that.
    What you re looking for is for the router to be a "VPN endpoint". Basically, to have the VPN client software built-in to the router. What type of VPN being used will matter since you can't normally install anything directly into the router like you would on a Mac or PC. So whether that can be done will depend on what HideIPVPN is using. I don't use that service but I'll guess that unless HideIPVPN uses a "common" VPN protocol like PPtP or L2TP, you're probably not going to find a VPN endpoint router that will work.
    The only workaround I can think of is to use your Mac to share it's internet connection to the xBox. That way all network traffic has to go through the Mac, which is connected to the VPN. I don't know if you can do that all wirelessly. You may have to attach the xBox to the Mac by wire. I know that's probably not what you were thinking, but if you're that paranoid that you need the protection of VPN for your xBox, then taking your xBox off of Wi-Fi is better security anyway.

  • Internal SharePoint site is not working through VPN for external computers.

    I have consultants trying to access our internal sharepoint 2010 site through our VPN. Whenever accessing the site from non-company computer through the VPN after setting up domain access for those users, they cannot gain access to the internal SP
    2010 site. When I or another employee accesses the SP 2010 site through the VPN from a company computer, the site loads. One consultant is using a Mac and the other is using a PC with compatible browsers. The SP 2010 site is set up using Kerberos authentification.
    Any ideas?

    Hi,
    How do you access the portal now? Via dns name? Something like
    http://subdomain.domain.com
    If that is the case, can you ping it from external client's outside your network and from inside your network? I believe from your internal network it will be fine. But from external with VPN, there may be error.
    So this will boil down network troubleshooting and http tracing.
    Please do Fiddler or httpTrace from the external clients over VPN for additional trobleshooting.
    Thanks, Soumya | MCITP, SharePoint 2010

  • Limitation on Service size for deploying

    Is there any limitation on Service size for deploying? The size of my service is 5MB approx. and I am not able to migrate it through Catalog deployer as well as Exporting and Importing file.

    There is no limit as such. The only limit imposed depends on the heap allocated for
              the JVM.
              Nitesh wrote:
              > Hi.
              >
              > Is there a limitation on the session size for a clustered environment. i'm not
              > sure whether its true or not. can anyone please clarify. Also is it for the entire
              > session object or per user.
              >
              > Thanks
              >
              > Nitesh
              Rajesh Mirchandani
              Developer Relations Engineer
              BEA Support
              

Maybe you are looking for