LMS 4.1 Patch Distribution Failure

I didn't have this problem in 4.0, and I've tried to upgrade 2 different model routers (891 and 2811) with the same error, anyone know what this means? Google was no help.
SWIM0151: The device is not running IOS Modular image in Install mode. Hence patch images cannot be distributed.
Thanks,
Craig

It sounds like you're trying to use the Pathc Distribution workflow for non-modular devices. Do not select Patch Distribution. Instead, select Software Distribution, and then follow the specific flow you want from there.

Similar Messages

OAS Patch Application Failure 10.1.2.0.2 to 10.1.2.3.0

Hello,
i am runnng RHEL 4.5 attempting to apply the 10.1.2.3.0 patch to my working installation of 10.1.2.0.2 standalone forms and reports services
During the installation it comes up with the error
Error invoking target 'frmweb_install frmcmp_install frmcmpb_install' of makefile /opt/oracle/forms/lib/ins_forms.mk
This leaves the forms conponent broken and giving the 'FRM-92101 - failure on startup - maybe invalid configuration' message.
I checked the installation log in my oraInventory/logs/installActions*DATE*.log as suggested. This shows an error during a make as implied.
Having done some searching around this forum I found that attempting to compile the forms manually often solves this kind of problem.
doing a 'make -f ins_forms.mk frmweb' gets most of the way and fails on
/usr/bin/ld: skipping incompatible type /opt/oracle/libiplsn.a when searching for -liplsn
/usr/bin/ld: skipping incompatible type /opt/oracle/libiplsn.a when searching for -liplsn
/usr/bin/ld: cannot find -liblsn
something linked wrong here?
Thanks for the help

ahh. Yes when I installed frs it complained that I needed to put bash into 32bit mode 'linux32 bash'. The 10.1.2.3 installer never did that.
Please can you advise me how to fix this issue and do a make clean. I'm not the most linux savvy person.
Am i going to have to reinstall OAS completely for 64bit? Is there a way to avoid having to do that?
Thanks
Edited by: user10695402 on 31-Mar-2009 03:42

LMS 3.2: Software Distribution - Generic Error

Hy.
I need to roll out an IOS on r.a. 250 devices. But when I try to distribute any software image via RME I always get the same error. I'm unable to start the job because in step one after selecting image and devices I get "failure" for all devices. When I click on "failure" a pop-up window opens telling me "generic error". Please have a look at the attached screenshot.
What does this mean and how can I fix this? This is really urgent!
All devices are completely managable (and managed) by the LMS.
Thank in advance!
Marc

Which IOS image are you trying to deploy and which device ?
Go to Common Services --> Software Center --> Software Update and provide screenshot.
Go to RME --> Admin --> Software Management ---> View/Edit Software Prefrences and check to see if "Include Cisco.com image " for recommendation is selected. If not, check them.
Try a different image that is higher that the current one and or use a GD image.

LMS 4.0 Config Collection failure

Hello Members,
i've added manually a bunch of Cisco Router 2911's and 2801's. On one of the the 2911 and 2801 the Config Collection fails. Data Collection, User Tracking, Inventory and Fault Discovery worked fine for all routers just on the two routers i get the failure?
any ideas? Which log do i have to check?
regards
alex

I believe the LMS reports this error because there was no vlan.dat in the
flash of the router. after adding a vlan.dat file on in the flash the vlan config
could be fetched and the error message doesn't appear any more.
regards
alex

After Effects patch update failure

Hi,
I´m trying to run After Effects CC on Mavericks. I downloaded the patch update (12.0.1) but I receive following alert upon installing "Update failure. You can not use updates. Please contact system manager". I have CC for teams, i´m an admin. Solutions anyone?

I followed these steps but still get the same error:

LMS 4.0 Software Distribution

Hi all,
I have some difficulties on software distribution on LMS 4.0
Attached are the logs.
Pls aid.
Thanks

1. Post screenshot of error.
2. Post show ver of both devices.
3. Enable debugs Admin > System > Debug Settings > Config and Image Management Debugging Settings.
4. Create the SWIM job again and notate the job ID.
5. Post the SWIM logs NMSROOT/log/swim_debug.log.
6. Post the SWIM job ID logs from NMSROOT\files\rme\jobs\swim\job-id\swim_debug.log where NMSROOT is the CiscoWorks installed directory.

LMS Prime Java Patches

Does anyone know if there are plans to develop a LMS Prime 4.2 software patch for the recent Java client updates? Not surprisingly our Topoogy Services feature doesn't work with client side Java patches applied

Hi Bryan,
Uninstall Java from your client machine, Launch topology on the client machine and let LMS decide the best version. It would choose the version as suggested by Afroj and then hopefully you would be able to launch topology at your client site.
Get back in case you still are facing problems.
Regards,
Syed Khalid

Instalation server patch distribution problem

HI!
I have set up an instalation server for GUI 7.10, and included both the GUI and BI components. I have patched them both with patches SAP GUI 7.10 patch level 3 and BI patch level 1 respectively.
The patching completes succesfully, NWSapSetupAdmin application shows that the patches are applied, but when the GUI is installed to a user machine, only the GUI patch is applied, and not the BI patch.
Am I doing something wrong, or is it impossible to distribute this patch via the instalation server?
Thanks,
A

Yes the client do have a correct certificate. If I change the boundary to point to a Server 2012 or Server 2008 Distribution Point they pull content without issue. When I change the boundary back to a Server 2003 DP they start getting "Access
Denied" once again.
The CAS log looks similar to the ContentTransferManager log in that it reports the link as HTTP instead of reporting it correctly as HTTPS like in the DataTransferService log. Its just not consistent and I have verified that you can't even access the
site through standard HTTP, it errors saying you must use a secure channel (HTTPS) and I am able to browse the site just fine as HTTPS.
A few entries from the CAS log are below:
CContentAccessService::NotifyDownloadProgressEx - downloaded size -2, total size 0 ContentAccess
Location update from CTM for content Content_be7aaec1-0fb3-4c51-8f12-5adb0673b44e.1 and request {293F5F55-5C9B-4E83-A442-B0A930EE447C} ContentAccess
Download location found 0 - http://SERVERNAME/NOCERT_SMS_DP_SMSPKG$/Content_be7aaec1-0fb3-4c51-8f12-5adb0673b44e.1 ContentAccess
Download location found 1 - http://SERVERNAME/SMS_DP_SMSPKG$/Content_be7aaec1-0fb3-4c51-8f12-5adb0673b44e.1 ContentAccess
Download request only, ignoring location update ContentAccess
Be kind and Mark as Answer if I helped.

LMS Software Image Management - Telnet failure

Hi all,
I had a problem with Software Image Management for the upgrade of a switch.
It seems that at the end of the upgrade, CiscoWorks was unable to save the configuration with telnet.
Yet, telnet seems to be ok because CiscoWorks manages to connect to the switch at the beginning of the upgrade.
Updating config file during software upgrade processDevice running-config is modified but failed to save the running-config to startup-config.Cause: Could not detect SSH protocols running on the device
TELNET: Failed to establish TELNET connection to 10.1.3.4 -Cause: Authentication failed on device 3 times.
I sent attached the logs of the upgrade.
Thank you in advance.

Hello,
The job fails last night after timeout.
I have reschedule job this morning for 2 switchs :
2960 with telnet and ssh enabled
2960 with telnet enabled only
The device credentials verification job seems to be coherent :
Device Name
Read
Community
Read Write
Community
Telnet
Enable
by Telnet
SSH
Enable
by SSH
1.
switch04-d
Ok
Ok
Ok(Primary Successful)
Ok(Primary Successful)
Failed to connect.
Did Not Try
1.
switch03-d
Ok
Ok
Ok(Primary Successful)
Ok(Primary Successful)
Ok(Primary Successful)
Ok(Primary Successful)
But the job fails again cause telnet authentication failed on device 3 times.
I do not understand why LMS does not use ssh if possible at the finish of the job? Why telnet authentication fails ?
Thanks in advance.

Lms 3.1 Device Collection Failure for Cat 6506-E

Unable to pull an updated device collection for a Cat6506-E running 12.2(33)SXI3. Was able to pull one when the device was running 12.2(33)SXH3, but not now. Anyone aware of a bug with the 12.2(33)SXI3 code? All other devices function correctly so I'm guessing an IOS bug, although I got tired of searching for it. Thanks in advance, Ernie

I've just upgraded to LMS 3.2, and LMS still can't inventory my two 6506-E.
I've run an "SNMP Walk" against one device, and it seems to work : here's the first few lines of it :
The following is a SNMP walk of device 10.x.x.x starting from
SNMP Walk Output
RFC1213-MIB::sysDescr.0 = STRING: "Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-VM), Version 12.2(33)SXI2a, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Tue 01-Sep-09 22:55 by prod_re"
RFC1213-MIB::sysObjectID.0 = OID: CISCO-PRODUCTS-MIB::cat6506
EXPRESSION-MIB::sysUpTimeInstance = Timeticks: (803850159) 93 days, 0:55:01.59
And I checked the IC_Server.log... this time it mentions SNMP timeout... I tried bumping the timeout to 20 seconds with 2 retries in Campus Manager.
I've attached my IC_Server.log excerpt.
Thanks for the help!
Alex.

LMS 3.2 software distribution: no result

Hi,
I have a 3750v2-48PS standalone switch (has been in a stack then removed). I wanted to upgrade its IOS by using LMS.
LMS shows me the following error
When I click on the error, it shows :
Switch has 128MB of RAM. The IOS I want to put into is c3750-ipbasek9-mz.122-58.SE1.bin, which has the following requirements:
FYI, I uploaded this IOS on another identical switch, manually, and it works. This time I want to do it with LMS.
Thanks.

Hi,
Kindly enable the debugging for the SWIM from RME > Admin > System prefrences > log level settings and enable the DEBUG for SoftwareMgmt and ConfigJob and hit APPLY
Now try the job again for one problematic device and wait for the job to complete. Note down the job id.
Kindly share the job id logs from the location :- CSCOpx\files\rme\jobs\SWIM\ -> send me the complete folder of the job id.
Also share the complete screenshot of RME > Admin > Software management > View\ Edit preferences.
Since its stack switch, kindly make sure you are using tar file of image to deploy the images from LMS.
Thanks,
Gaganjeet

Cache Distribution failure

Hi all,
What is the optimization features available in the Distribution Cache Mechanism.
Currently Im running two clusters in 2 nodes and observed the performance is degrading when the clusters (from different nodes) are added.
Can any one help me on this?

Hi,
Can you elaborate more on the issue? If you are adding more clusters to the same node, it is obvious that you are trying to squeeze more juice from the same hardware so it is expected.
Cheers,
_NJ

Patch update failure.. on mac!

Hello!
Im currently having an issue updating / patch all my CC 2014 programs.. I've tried to reinstall all the programs and as soon as the installation is done it says "installation succeeded but a patch failed u43m1d205"
I have been searching for an answer in all the threads I could find without finding a solution.. this is not the first time im having HUGE problems with Creative Cloud but atleast the after awhile I have always been able to fix them but not this one..
Im currently running it on a Mac 10.9.4 and all the programs works except for indesign that crashes after I have been using it for some minutes and it's very annoying..
Anyone have any tip?
these things have I tried already..
Reinstalled ALL the applications including Creative Cloud
Created new folders for AAMUpdater + OOBE without any help.
Downloaded the patches one by one everyone failed except for one (illustrator)
Tried to update it from the program without any progress...
the only thing I have left now is to reinstall the hole computer but I don't see why that would solve the problem since the computer is only 2 weeks old...
I would greatly appreciate any kind of help regarding this matter.
Best Regards
EDIT!
Have now also updated Mac IOS to 10.10.1 still same error!

Hi Mark,
Are you getting any specific error while trying to install Acrobat DC? Could you please retry the installation after the system restart?
If the problem does not get resolved even after system restart then please share these additional information :
1. Which operating system are you using?
2. Do you have any previous version of Acrobat installed?
3. How are you installing Acrobat? Could you please share the link from which you have downloaded the Acrobat?
4. Also could you please share the following logs (if available) :
     1. PDApp.log file from ~/Library/Logs.
     2. Acrobat Installer logs (Adobe Setup Error.log and Adobe Acrobat DC 15.007.20033 <Date>.log.gz) from /Library/Logs/Adobe/Installers.
     3. install.log from /var/log.
Thanks,
Tushark

CISCO PRIME LMS 4.1 ---- Software distribution fails with SWIM1113

Device will be rebooted.
SWIM1113: Device Reboot operation failed or Reboot Verification failed.
The device is not running the new image after it is rebooted.
Verify the configuration used to load the new image. Verify whether the new image exists on the device in a valid Flash partition
the software distribution , i select image for upgrade for router 1841 and select reboot immediatly after downloading so my device take new image but can not reload with new image ...
please help me

check if you have this command configured on the device ::snmp-server system-shutdown
if not configured it and it should reload it
Thanks-
Afroz
****Ratings Encourages Contributors ***

LMS and CSCsx09107 patch

Hello,
I want to intall CSCsx09107 patch, as prerequisite is necessary to install open ssl but the url doesn't work
Prerequisites
Before installing this patch on Common Services 3.0.5, 3.0.6, 3.1, and 3.1.1, you must install OpenSSL 0.9.71 Security Vulnerability patch.
The OpenSSL 0.9.71 Security Vulnerability patch is available at:
http://www.cisco.com/cgi-bin/tablebuild.pl/cd-one-3des
Where can I find this patch?
Thanks

these links should work:
windows:
http://tools.cisco.com/search/display?url=http%3A%2F%2Fwww.cisco.com%2Fcisco%2Fpub%2Fsoftware%2Fportal%2Fselect.html%3Fi%3D%21s%26imageGuId%3D1AB937BA783D2FA34BF059FA10569F8D99AC6CA0&pos=2&strqueryid=1&websessionid=a1TL1F4XIy0UC_IueZ1-BH3
solaris:
http://tools.cisco.com/search/display?url=http%3A%2F%2Fwww.cisco.com%2Fcgi-bin%2FSoftware%2FTablebuild%2Fdoftp.pl%3Fftpfile%3D%2Fcisco%2Fcw2000%2Fpatches%2Fcd-one%2Fcwcs-sol-CSCsx09107.tar&pos=5&strqueryid=1&websessionid=a1TL1F4XIy0UC_IueZ1-BH3
in
in the last time I found the software search feature very helpful:
http://tools.cisco.com/search/JSP/search-results.get?http://www.cisco.com/cgi-bin/Software/SWSearch/SWSearch.cgi
and just enter
CSCsx09107

LMS 4.1 Patch Distribution Failure

Similar Messages

Maybe you are looking for