M45-S2653 will not boot unless an external monitor is connected to it

I've got a similar situation with an M45 which I posted to http://www.tomshardware.com/forum/207245-28-toshiba-laptop-locking. I figured I'd post here too.
I can only shut it down or put it into hibernate by holding the power button until it turns off. After doing that yesterday, I can not get it to start up today.
The sequence of events that occurs is:
Hit power button with power and batter lights both blue.
HDD light goes blue for split second.
Power light goes blue and stays on.
Computer attempts to access DVD drive.
Computer makes a clicking sound.
Battery light and power light go off.
Batter light comes back on.
Computer never boots.
In reading some other posts, I've found the root cause for my issue (sort of). If I hook it up to a monitor, it boots no problem. So...
In order to use my laptop as a laptop now I either need to always carry a monitor with me, or figure out how to get my screen to start playing nicely with the rest of the laptop.
Does this sound like I need a new LCD? Is there anything else I can try? $300 for a new LCD to put in a 3 year old, $500 laptop (when it was new), that is currently only worth the data on the hard drive, it doesn't really make a whole lot of sense...
Any suggestions?
I can still hit Fn F5 and get either the LCD or the LCD and the Monitor to both display. However, when I shut it down with the LCD working and tried to turn it back on, same problem. It would not boot because the display is in some way defective.
I have updated to the latest BIOS version and graphics adapter files available on the Toshiba website...
It's like the laptop needs a monitor connected to it to jump start it. Once I connect a monitor, I can run it and use the screen, but I need to do this step each time I either turn it on or bring it out of hibernate...
Message Edited by dwill122 on 12-10-2008 08:49 PM

you did nothing wrong what you have to do go back to your old computer and find where iTunes kept your music (usually in the music folder that is listed in the windows explore, if that does not work do a search for iTunes media) then plug in your external and transfer the music from your old computer to your external. depending on the amount of music and the type of USB cable you have it should be no more then a couple of hours. Once you have done that safely remove your external and plug it in to your new computer and the transfer the music from your external to your new computer. Once you do that have iTunes go and find the music. Hopefully everything will work out

Similar Messages

Mac Mini i7 (Mavericks) will not boot from the external drive

Mac Mini i7 (Mavericks) will not boot from the external drive with Disk Warroir 4.4. or Drive Genius or Lion.
Not even from the external Firewire hard drive with Mavericks

Does the external HD have a GUID partition table?
Is the external drive formatted Mac OS X Extended (journaled)?
Is this a 2011 or late 2012 Mac?
How was Mavericks installed on the external drive?
Who is the builder of the drive mechanism in the external drive?
Who is the builder of the external enclosure?
What type of interface does the external drive have USB2, USB3, Firewire 400, Firewire 800, thunderbolt?
Is the external enclosure directly connected to the mini?
Have youtried a different interface cable?

I have a new macbook pro 2,6 Ghz i7, 8GB 1600Mhz internal ram. He will not boot from an external disk with operating system Snow Leopard

I have a new macbook pro 2,6Ghz i7, 8GB 1600 Mhz internal ram, but he will not boot from an external disk with operating system Snow Leopard.

These Macs shipped with 10.7, and will run nothing older than that:
MacBook Pro
Date introduced
Original Mac OS X included
(see Tips 1 and 3)
Later Mac OS X included
(see Tip 1)
Mac OS X Build(s)
(see Tip 2)
MacBook Pro (Retina, Mid 2012)
Jun 2012
10.7.4
11E2068
MacBook Pro (15-inch, Mid 2012)
Jun 2012
10.7.4
11E2617
MacBook Pro (13-inch, Mid 2012)
Jun 2012
10.7.4
11E2617
MacBook Pro (13-inch, Late 2011)
Oct 2011
10.7.2
10.7.3
11C74, 11C2002, 11D2001
MacBook Pro (15-inch, Late 2011)
Oct 2011
10.7.2
10.7.3
11C74, 11C2002, 11D2001
MacBook Pro (17-inch, Late 2011)
Oct 2011
10.7.2
10.7.3
11C74, 11C2002, 11D2001

My iMac running lion will not sleep if an external HDD is connected.

My Imac will not sleep if the external HDD is connected. This just began to occur. If I unplug the drive it goes to sleep. This doesn't happen with any oter USB pereferals.
Thanks in advance.

From the menu bar, select
 ▹ System Preferences... ▹ Network
Click the Assist me button and select Assistant. Follow the prompts. How far do you get?

G4 PM will not boot after using Target Disk mode connected Intel iMac.

Hi,
We have some new Intel iMacs and have transferred some information from our previous G4 PM (one MDD and one Quicksilver) to the new iMacs. For some reason the G4's will now not boot up and kernal panic on the gray Apple boot screen. This has happened to all the G4's we have in our office. They are running OSX 10.2.8 and the iMacs are running OSX 10.4.4. We can still mount the drives from the G4's using FireWire Target Disk mode.
I have tried zapping the PRAM etc but they still wont boot. I have also tried running the OSX 10.2 Installer disks to try and reinstall OSX on the G4's but the installer cannot see the drives?
Anyone have any idea what is wrong. Never had this problem before using the FireWire transfer.
Thanks,
Nick.

I had an experience with a mini mac after booting in target disk mode while connected to a blue and White G3 via Firewire. After attempting a restart, all I got was a blinking ? which usually means the startup disk or system folder can not be found.
I fixed this problem by booting using the originall install CD and then using the startup disk menu to reselect the original system disk/system folder as the startup disk. On reboot. all was good. Only took a couple of minutes.....

Mac mini will not boot up with two monitors attached

New Mac mini running OS 10.10.1. I have a LCD monitor attached to the HDMI port, and a Cintiq 21 UX LCD monitor attached to a thunderbolt port.
It boots up properly with only the first LCD monitor attached to the HDMI port.
When I leave both monitors connected before starting the computer I get no chime, and a black screen. The light on the front of the Mac mini comes on, but nothing else happens. I have to turn off the Mac mini, unplug the second monitor and then reboot. It always starts up perfectly then. After starting the computer, I plug the second monitor in, and everything is fine.
It’s kind of a pain in the neck to constantly plug and unplug the second monitor from the back of the Mac mini. Is there anything I’m overlooking?

Thank you, Illaass! Resetting the SMC solved the problem! I tried that first because I would prefer not to lose any preferences, and also because it was the easiest to try. You must be a genius in addition to being such a good egg!
(This is the number of smiles I smiled after my Mac mini booted properly with both monitors connected.)

Z87-G45 will not boot unless I enter BIOS or boot menu

Hi,
I v got some problem with my Z87 - unless I enter BIOS or boot menu(F11), I v got error message "Reboot and select proper boot device....".
When I enter BIOS(or boot menu), and dont change anything, exit&save it boots just OK.
The boot priority is simply the OS drive as 1st and everything else disabled. Every single driver is up to date (using supplied live uptade for board (v1.7 bios), and official inter drivers for OS drive (intel SSD), sound, graphics,... everything). Nothing but mouse, keyboard and LCD is connected to the PC. No DVDs inserted, no USB flash drives. Win7 64-bit clean(except drivers ofc) installation.
Any ideas what might be the problem?

Quote from: ondrej.byrtus on 09-May-14, 01:57:58
Hi,
I v got some problem with my Z87 - unless I enter BIOS or boot menu(F11), I v got error message "Reboot and select proper boot device....".
When I enter BIOS(or boot menu), and dont change anything, exit&save it boots just OK.
The boot priority is simply the OS drive as 1st and everything else disabled. Every single driver is up to date (using supplied live uptade for board (v1.7 bios), and official inter drivers for OS drive (intel SSD), sound, graphics,... everything). Nothing but mouse, keyboard and LCD is connected to the PC. No DVDs inserted, no USB flash drives. Win7 64-bit clean(except drivers ofc) installation.
Any ideas what might be the problem?
I am under the impression that this not a fresh build...did you remove recently any drives....do you have dual boot....?

Macbook Pro mid 2009 will not boot unless SMC is reset (macbookpro5,5)

Hello!
I have a mid-2009 Macbook Pro (macbookpro5,5) and I've had this weird issue for like a month, and I ran out of ideas.
So my problem is: whenever I turn on my mbp (either on OS X or Windows 7) it will go to sleep (on OS X after it shows the login screen and on Windows when it's loading) and when it wakes up, *it goes to sleep again*!
I kinda panicked back then because I couldn't get to boot the machine for all what was worth, but then I tried resetting the SMC and voila! it booted; and I thought that was it, but no, it wasn't: *I have to reset the SMC everytime I turn on the mbp*, or else the same sleeping loop will happen again and again.
This happened after installing the first March Update that Apple released (which misteriously only addressed iTunes issues - supposedly) on OS X. I already tried looking for SMC or EFI updates (just in case) and I already have the current versions (just EFI, SMC updates were never released for this mbp) so now I have no clue on what to do...
And what really puzzles me is that I disabled sleep when closing the lid on Windows 7, and it worked fine, but after this issue, it just goes to sleep, even when I see the closing the lid option on "do nothing", it's just weird.
Does anybody had some sort of trouble like that?? or anyone has some hints that may help me??
Message was edited by: piku9000

Well, it seems that apple fixed this issue in the 10.6.7 update. I kinda wish there was a little more documentation about the patches released and what files they modify, since no update was released to the SMC, I have no idea why it had to modify it. Anyway, thanks for the help!

G5 Dual 2.5 CPU Power PC will not boot unless I remove the Plastic Sheild.

G5 Dual 2.5 CPU with 4 gb of memory will boot everytime if I take the plastic sheild out. I bought it from a guy who would turn it on then let it sit until the fans revved up after about 5 to ten minutes. I figured out that it would boot everytime if I removed the plastic sheild. Now I am trying to find a permanent fix for this issue.
Thanks for any assistance anyone can give.

I don't think its just a plastic shield and door - there is a contact switch that signals when these are removed and the fans rev up to a higher speed. My guess is its the higher speed of the fans that's keeping things cool during the power surge of the boot stage thats allowing it to startup.
When the doors are on and the fans are kept low there must be some hardware failure that is occurring during boot up - that seems to be prevented when speeding the fans up. And after the initial boot up power surge, things run cool enough that I can safely put the plastic shield and door back on and the computer keeps running fine (it ran OK all night).
I can think of no other logical explanation at this time.
Any other ideas?
What puzzles me, is I use this computer to do some heavy 3D graphic renders and have run it intensely for days at at time with absolutely no sign of failure during operation once its booted up. I've never had a freeze or anything like that. So when its so reliable during operation, why so fragile during boot up?

Envy DV7 laptop will not boot without the power cord being connected

My laptop won't boot on its own even when the battery indicator reads "fully charged (97%). If I have the power cord plugged into the computer (and the wall), it boots right away. Without the power cord, the "power indicator light" flashes once, the screen brightens to a lighter shade of gray, then it just shuts down.
I'm thinking I need to replace the battery but I thought it best to check with the experts first...................☺
Thanks!!
ETA..........I just saw the post about power cord failure. My power cord is one of those affected and I will be filling out the request for a replacement. Unfortunately my serial number is apparently located inside the battery compartment. I'm wondering if my cord has overheated and caused this boot problem with my computer.

Hello, @jksweeney
Welcome to the HP Forums.
I see that your having an issue with the power and your notebook. That you've applied to have the power cord replaced as it was part of the recall.
Please let me know when that has been taken care of if the issue remains. I will remain subscribe to this thread, so that I will be notified if you post again.
Thank you for posting on the HP Forums.
I worked on behalf of HP.

Windows 8 and Canvio Desk 3TB: System will not boot when external hdd is connected

http://h30434.www3.hp.com/t5/Desktop-Operating-Systems-e-g/HP-PAVILION-A6109N-amp-windows-8-System-w...
Hi,
just recently upgraded to Win Pro on my HP PAVILION A6109N. I also bought a toshiba canvio desk 3TB. What I notice is that if I reboot my pc with the extermnal HDD connected, my system will not boot.
I have check my BIOS boot settings and the order of the boot.
I have tried disabling USB Legacy Support in the BIOS
I have reformatted the external HDD
but still my desktop will not boot if the external HDD is connected....If I disconnect the external HDD...the system will boot up ....
I am at a loss....*** scratching my head ***

Update: The only solution for me was to format the drive as ext3 and plug it into one of my Asus RT-N66U USB ports, as most routers don’t yet recognize 3TB drives as NTFS. It’s not much help to people who don’t have a router with this capability, and it also slows transfer rates to ~12MB/s.
Given the short length of the cable, your only other options are to have the 3TB Canvio sitting right next to you so you can unplug from a front USB port before each boot, or place it towards the rear of your desk and crawl under the desk to disconnect it from your PC prior to each boot.
It's a pity because Toshiba produce great internal HDD's, but my experience when it comes to external drives is they're simply junk. I wish I had read the reviews before purchasing.

IMac will not boot with external monitor connected

Hi everyone,
I have a mid 2010, 27" iMAC. If I connect an external monitor to the Mac (using display port), everything works as it should. If I try to reboot or do a cold boot while the external monitor is connected the system boots to a white screen and no further. Sometimes I get 2 spinning colored wheels, but nothing more. If I let it sit at the white screen long enough the screen saver kicks in and everything goes black, move the mouse or hit a key and the white screens come back.
I've tried a few things (that I've found on-line) but I'm an old PC user (25+ years) so I'm not used to or know all the tricks or what I really should be trying.
I just upgraded to Mountain Lion thinking maybe that would help, but no change.
Any help would greatly be appreciated.

Sorry about my lack of details, I am using the Apple brand of display port to DVI adapter, a DVI cable that is plugged into an ACER 26" monitor (not sure of the model nuimber right now as I am at work). This monitor and DVI cable worked fine during reboots/shutdowns, etc while connect to 2 different Intel based PC's that I have that also run dual monitors. As I mentioned I've done PC work for many moons and would know how to check for drivers, etc, but now in the Apple environment I am lacking these same skills. So I've done all the standard stuff, switching known good cables etc, but I am unsure of how to uninstall drivers and those type of tasks if need be. I know it could be a monitor problem, but that same monitor works fine while connected to the PC's that I have.

Powerbook G4 will not boot normally, only in safe mode.

So...about a month ago I updated my powerbook with all the updates that were available, one of the updates was 10.5.8. I came back after the update had run for a while, and found my computer with a black screen, and a faint white bar towards the bottom of the screen. The computer wouldn't respond, and I was forced to do a manual shutdown. The computer would then not boot, instead finally resting on a light blue screen with an active mouse pointer after passing the gray apple screen.
In safe mode, I downloaded and installed the combo 10.5.8 update, but it made no difference.
I assumed it to obviously be a software issue, and so I backed up my info, and reinstalled Leopard. I then updated to 10.5.8 using the combo update. My computer functioned normally for about a week, and then froze, mouse responsive, but nothing else. After manual shutdown, same problem, computer started to blue screen with pointer.
Since that time I've reset the PRAM, run disk utility a million times (no errors), repaired permissions, all to no avail. I've run the Techtool diagnostics on it, and it found no hardware failures. The computer will not boot from an external hard drive, ruling out the HD.
I've replaced the RAM with different RAM, again will not boot. The computer boots without fail every time in safe mode.
History on my computer, one of my memory slots failed to recognize memory any longer, and my logic board was replaced a little less than 2 years ago while I still had applecare.
So to sum up:
Powerbook boots only in safe mode
Stays at blue screen with mouse pointer when booting
May work properly for a few days after erase and install of OS, but then fails again with same systems shortly thereafter
Any ideas???

Have you tried running the Apple Hardware Test from DVD?

PB does not boot UNLESS I remove Airport Extreme Card

My 15" PowerBook G4 will not boot unless I remove the Airport Extreme Card. I doubt there is a problem with the card itself. Could it be an issue related to the internal components that the card plugs in to? I read on another forum that my issue could be a faulty connection between the card and the logic board (part no.821-0352-A).

Thanks for your reply, i totally agree and i have never had a issue with toshiba warranties before usually they are very good and i reccomend toshiba aftersales service to all our clients.
My only concern is that they didnt check it properly last time and if they dont find a fault this time they will be charging me 80 plus vat to get my laptop back according to the toshiba rep. This is not a fault that happens during normal operation and takes hours to replicate if they dont then they wont find the fault.
Fingers crossed they find it this time otherwise i may have a battle on my hands.

On cold boot or restart, MacPro will not start unless CD Tray is open. Any ideas why ?

On cold boot or restart, MacPro will not startup unless CD Tray is open. Any ideas why ?

hello Singyt, the bug report associated to this kind of crash indicates that it might be a malware related issue.
your crash report also shows a file named "urixalog.dll", which doesn't turn up any search hits on google, which is also slightly suspicious. could you search for that file on your pc and upload it to a site like virustotal.com in order to analyze it.
please do a full scan of your system with the security software already in place and/or a different tool like the [http://www.malwarebytes.org/products/malwarebytes_free free version of malwarebytes].
[[Troubleshoot Firefox issues caused by malware]]
edit: the bug report also suggests that a monitoring program named spector pro/360/... which essentially acts like malware, might cause the issue. in case you have that installed please remove it. otherwise [https://support.mozilla.org/en-US/kb/Firefox%20crashes%20when%20you%20open%20it#w_backdoor-ulrbot-c here] would be a removal guide for urixalog.dll

M45-S2653 will not boot unless an external monitor is connected to it

Similar Messages

Maybe you are looking for