M6-n012dx HDMI out to 3840x2160 60hz?

I recently bought a new 4k television and trying to output the PC display as 3840x2160 at 60hz, but capped at 30hz. Is this a hardware limitation of the Intel 4600 chipset, or should I be able to output at 60hz? I can't seem to find if the HDMI port on this laptop supports HDMI 1.4 on any documentation.

Hi ,
Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!
I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about your HP ENVY m6-n012dx Notebook and concerns with the limits of the HDMI v1.4 output. Here is a link to your manual page 3. Your Notebook supports HDMI v1.4 supporting up to 1920×1080 @ 60Hz. Hope this addresses your concerns. Thanks.

Similar Messages

Primo 81 hdmi out.. how to get it working

Hey, I picked up a primo 81 for my wife and we are trying to get it to output to the tv via the hdmi out... Any idea's? The pdf mentions nothing about it.

Quote from: badboy2k on 27-December-13, 03:10:09
ok on that tablet I'm not sure where it is exactly as its android (i have very little use of it and anytime i have used a HDMI its just been sent to a 1080p screen) but find the settings menu and find the one for HDMI as I'm fairly sure by default its trying to output a signal at 1080p @ 60hz not 720p @ 60hz and you will have to change that to fit the monitor (also when you plug in the mini HDMI does it bring up a dialogue box saying HDMI connected? (also make sure you have your TV on the HDMI in that its using))!
No, I do not get any dialog box saying hdmi connected.. And I can not find any settings anywhere for changing the hdmi output resolution.
Thanks again for the help guys.

Thinkvision Pro2840m flickering at 3840x2160 60Hz

I have just installed a Pro2840m display on a brand-new Dell T5810 workstation (with AMD W5100 graphics card), and the Pro2840 display flickers really badly when setting to the resolution recommended by Windows (3840x2160 @ 60Hz).
The flicker goes away if I reduce the refresh rate to 30Hz.
The monitor is running microcode TN3.01. Windows drivers are up to date (AMD 14.301.1010), and system is running Windows 8.1, with 8GB memory
Any ideas?

Hello and welcome to the Lenovo community. Out of experience I would suggest you connect only the (or one) Pro2840m to your W5100 using the supplied DP cable (by Lenovo) to test whether the fault is with the Lenovo. Obviously don't forget to be running the latest ISV certified drivers published for the particular software you are planning to use found here.
As a side note: I wonder when was your display purchased, because microcode LN3.01 was the very first version these displays were shipped with in June 2014. The latest version which I have heard of for the Pro2840m was at LN3.07 which has addressed a list of serious issues (see here or here for examples). Sadly firmwares for these displays are not released to public, for upgrading your firmware you will have to contact Lenovo support and request an RMA.
Don't forget to post back your findings so we all can benefit.

Macbook Pro 2011 DVI HDMI out does not work with TV when the power cable is connected

My Macbook Pro (Early 2011) DVI HDMI out does not work with TV when the power cable is connected. If get the blue screen and then can use the macbook but nothing is displayed on the TV. If i go into display I can see that there are two screens but nothing displayed on the TV. If i take the power cable out at this point the TV shows the second desktop as expected. If i then reconnect the cable, the screen flickers, as though it is being affected by the power cable, and the screen goes blank on the TV. Only if i remove the DVI cable do i get the blue screen again. If i remove the power cable and reconnect it will do it every single time, so i cannot see it being a TV issue or a minor glitch.
I have had this working previously but at the minute it seems to not be playing ball....any thoughts
Thanks
Dan

BUMP
Any ideas?

I have an Retina display MacBook Pro with HMDI out port. I also have an HDMI to Component cable with Audio Plugs. How can I get HDMI out to work with this cable when plugged into the Component and Audio ports on my TV?

I have an Retina display MacBook Pro with HMDI out port. I also have an HDMI to Component cable with Audio Plugs. How can I get HDMI out to work with this cable when plugged into the MacBook Pro and connected to the TVs Component and Audio in ports.

Will not work. To my knowledge, dual converting like that isn't supported. The Mac must detect the connected video output device and that sort of info cannot be done across an analog component uni-directional connection.

Can I display EyeTV's live TV over HDMI-out and be able to see my desktop using screen-sharing on a headless mac-mini used as a media-box?

Hi,
I'm thinking of buying a new mac-mini to replace my current one which acts as an iTunes server and records TV programs using eyeTV. I connect using screen-sharing/VNC to be able to do stuff on it (like handbrake etc.)
I have eyeTV with a satelite receiver and I want to change the setup so that:
- the new mac-mini continues to work as an iTunes server (and handbrake workhorse)
- I can use the HDMI output (inc. audio) to show eyeTV's live TV full-screen app
- I can connect using screen-sharing/VNC to the mac-mini and see my normal desktop to be able to maintain it etc. but this is a headless display (no screen is connected to the display-port).
- recorded media I'd play through the appleTV2 still + rentals etc. unless anyone knows if eyeTV software can offer up iTunes content? I don't like the eyeTV recordings in general as it seems very slow to me for access when there are lots of recordings and wouldn't be available in other apleTVs in the house AFAIK.
The main benefit that this gives me is that I'd no longer need a seperate satelite box to watch live TV and can add more eyeTV hardware to get additional TV channels all through the same HUD on the TV for ease of access.
Does this seem possible in theory & practice (ie are there any gotcha's to consider?)
- can I force the HDMI output resolution to 1080i as I go via an amp to the TV and the appleTV2 drops to low-res in this configuration so I have had to find a workaround for that.
- does the mac-mini have IR input that can be programmed?
- Does eyeTV software remain stable for long periods?
- Does the HDMI out have any handshake issues that would need a reset of the display (somehow)?
thanks in advance for any thoughts/contributions
Lee

I think the easiest way to do this is to have the EyeTV app running in one user account and sent via HDMI to the TV, and use a separate user account for Screen Sharing. Both logins can be active at the same time and with Lion you can connect via screen sharing to which ever login you need.
With regards to the Mac video resolution changing, when it is not the current input on your AV receiver. This is 'normal', if the Mac sees no signal it drops down the a lower level. What you need is to buy a HDMI Detective Plus which tricks the Mac in to always seeing a signal and hence it will not drop down the resolution. See http://www.gefen.com/kvm/dproduct.jsp?prod_id=8005
The Mac mini does have an IR receiver. This can be used with the EyeTV app, iTunes, and similar. Yes I believe EyeTV would run for prolonged periods quite happily, it is has been around for a long time and had most of the rough edges polished off. However one issue you will have to deal with is that it does not automatically update its program guide data. For this you might have to write or modify an AppleScript. Elgato support or their user forums will be a lot of help.
You can set EyeTV to convert recordings to an iTunes (Apple TV) compatible format and then delete them from EyeTV.
The HDMI Detective should solve your handshaking problems.

I have a mid 2009 Macbook Pro and i know the Mini-display port does not support audio out but does it support HDMI out? or do i have to buy a Mini-display to DVI and then a DVI to HDMI adapters?

I have a mid 2009 Macbook Pro and i know the Mini-display port does not support audio out but does it support HDMI out? or do i have to buy a Mini-display to DVI and then a DVI to HDMI adapters?

Run MDP to HDMI for picture. Use a cable like this to run sound from your audio out on your Mac to your TV's audio in. That's about all you can do.

Does the iPhone 4S support HDMI- OUT via the digital AV adapter?

Does the 4S support HDMI ->OUT via the digital AV adapter or not? I read that it does (whether it be mirroring, YouTube video playback, movie playback, etc.) but I'm not having any luck. I recently tried my AV adapter (that I normally use with my iPad 2) but I get nothing. When I power cycle the phone after connecting the adapter, I get a error stating that the "accessory is not supported by iPhone". When I go to play a YouTube video, it shows up on the phone's screen for a second and then disappears. The LCD TV I am connected to never prompts me for the detection of a new HDMI device being connected" either, do I have no clue what's going on.
Any ideas? Thought?
Any help to solving this riddle once and for all would be appreciated.
Thanks and Happy New Year!!
Andy
P.S. - my 4S is running iOS 5.0.1 and is a Verizon 16gb model.

The model number on the adaptor is A1388. The link is here:
http://store.apple.com/us/product/MC953ZM/A?fnode=MTc0MjU4NjE
I have the iPhone 4s, running 5.0.1 (9A405)
I have also experimented with sequence, and I see no particular order needed to make it work. Generally I get it all plugged in and then swipe the iPhone and in a few moments, the screen appears in mirroring mode. Then if I go to Videos I can play my clips with sound, or I can do Keynote presentations, etc.
So sorry to hear you're having trouble. I imagine you've already double-checked that you're seating it solidly in the dock connector and have a good, working HDMI cable. I am not sure what you mean in your original post about "powering up" the phone. It might also be some Verizon issue, though I don't know what that might be. Is your AV adaptor the Apple branded one?

Can I use the HDMI Out on my macbook pro retina for audio without connecting a video device?

While the MBP has TOSLINK output from the headphone jack, TOSLINK does not have the bandwidth to carry the high resolution audio from many blu-rays and DVD-Audio disks. I would like to hook my MBP to an audio-only HDMI sink so I can pipe the multichannel output to my surround speaker setup.
My concern is that the MBP will get "confused" and do one of the following things - both of which are "bad":
1) It will decide that a video device is there, and put the desktop on the nonexistent HDMI display OR
2) It will decide to send no signal at all (no video, no audio) because it sees no video device.
Any thoughts on this?
In short - thinking of using something like this: http://www.ambery.com/2hddodtsdihd.html
with the HDMI out of the MBP and then piping its 6 discrete analog outputs to my old (but excellent for computer speakers) Logitech Z680 setup.
But I want any movie video to remain unperterbed on my Thunderbolt display. And if I am not watching a movie and am just listening to multichannel FLACs or something, then I'd like to run the media player normally and have the usual desktop on my MBP or Thunderbolt display.
Any thoughts?
Thanks to all!!
-L

nopenshaw3 wrote:
I have searched through the forums relentlessly of both Mac and third party, but I seem to never find a good, well thought out answer for my specific question. Every answer is filled with snobby know-it-alls who either respond with sarcastic answers or post links to other threads that don't answer the question in an attempt to make the asker feel like an idiot.
Not the best way to get started frankly but ...
nopenshaw3 wrote:
QUESTION 1: Is there anyway that I can buy a new logic board with upgraded graphics card and it will work?
Not from Apple, you can go to the grey market if you choose but it is most likely that the only MB that will work is the one you already have.
nopenshaw3 wrote:
I have also read a little bit into using the Thunderbolt port as a means to run an additional graphics card through, the hardware for it being built by a company named Sonnet.
QUESTION 2: Is this an option that will actually work with my Macbook Pro setup and give me better graphics card capabilities?
Maybe, if the Sonnet is properly Thunderbolt compatible it should.
nopenshaw3 wrote:
So with that said, please, If you're going to respond, just do so in a manner that will actually help me out. I know it's a lot to ask, but please, PLEASE DON'T BE ONE OF THOSE PEOPLE!
Yes, well ... you have a nice day now.

Can I use the HDMI out on a HP ALL IN ONE TOUCHSCREEN Desktop to connect a second monitor with HDMI

Can I use the HDMI out on a HP ALL IN ONE TOUCHSCREEN Desktop to connect a second monitor with HDMI in without any additional software or graphics adaptor. I have a 520-1070
HP - 23" Touch-Screen TouchSmart All-In-One Computer - 8GB Memory - 2TB Hard Drive ? I used a HDMI to HDMI cable and the monitor was not recognized.

Here are the specs for your HP TouchSmart 520-1070 Desktop Computer. As previously stated your computer Doesn't have a HDMI output, instead it has a HDMI input. This is designed to let you connect a game console, a DVD/Bluray player, etc. to use as a monitor.
If you wish to conect a second monitor to your computer, you will need to use a USB-to-video adapter such as the EVGA UV Plus+ UV39 or EVGA UV Plus+ UV19. Using an adapter like these with the touch feature of your computer may cause issues with pointer control and you may need to disable the touch feature to use "extended desktop".
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

HDMI out from Timeline

Hi,
I am doing a job for an Art Gallery, in which I have to shoot, and do a quick edit (no effects), and output to a Full HD 1920x1080 TV.
I intend to buy a Panasonic AG-HMC70U Shoulder Mounted Camcorder, which stores AVCHD 1080/60i (NTSC) video in SD/SDHC Cards.
I intend to buy a Sony VAIO F VPCF127FX/B 16.4" Notebook Computer, with Windows 7 Premium 64 bit, processor 1.73GHz Intel Core i7-740QM, 6 GBs RAM, and nVIDIA GeForce GT 330M with 1GB Dedicated.
Will I be able to output directly from CS-5 Timeline to TV, through notebook's HDMI out?
Thank you,
Ronaldo

Thanks a lot robodog2
I have a few questions bellow in red:
I would get 1 Terabyte drives instead...they are not expensive. You might need the extra room if you have to do some exports to files. Get the fastest ones you can for editing...esata better than fw800...make sure you turn off indexing and format NTFS and assign specific drive letters to the externals...put tape on driive with the drive letter you gave it clearly marked. If you dont you will have a hard time swapping them and maintaining links with your project(s).
Agree.
dont partition any drives
Agree.
when you say dvd you mean of course Blue Ray...for HD.... dvd is for SD....just dont forget when you look for disc burners.
Yes...Blue Ray, I keep saying DVD....
There's a program called neoscene by cineform that a lot of people use for avchd footage....you might want to look into having that just in case.
I'll check into it.
Test the tv -- output real footage from timeline to the same HD Tv you plan to use at show ....output to make sure it likes interlaced footage.
Here is the catch, I'm in Brazil, and this work will happen in Grand Rapids, Michigan, and we arrive 1 day before....this is why i'm trying to prepare as much as possible, in theory, before hand....
You'll probably put OS and program on C drive
Agree.
put pagefile on 2nd drive 1.5 x your ram with min and max size the SAME MAX SIZE so it never gets fragmented...do that first thing so the pagefile is near the center of disc. I guess you said 2 internal and 3 external ? so you can put your scratchdisk on disc 2 also...and assets and any exports you need to do on the externals...
I will have 2 Sony VAIO F VPCF127FX/B 16.4" Notebook Computer, with Windows 7 Premium 64 bit, processor 1.73GHz Intel Core i7-740QM, 6 GBs RAM, and nVIDIA GeForce GT 330M with 1GB Dedicated.
So, here you lost me...
1 - How do I - 1.5 x your ram with min and max size the SAME MAX SIZE so it never gets fragmented
2 - How do I do this pagefile to start at center of dics?
I will only have one internal disc, dedicated for OS.
Scratchdisk, assets and exports - I will have 3 external discs in total, one to edit, one for playing to, and the third one for copying....
plan on having an "emergency" helper that REALLY knows whats up with the computer and editing stuff in case you get stuck and have to focus on shooting and need help ...line that up beforehand.
Agree.
go to the gallery and see if you can do anything to enhance the lighting or color correct lights, windows etc beforehand...
test everything .....so you dont have surprises that make you crazy on the day.
That will be impossible as we arrive 1 day before...I'm taking my lights, tripods, color gels...
good luck sounds like fun..
Thanks a lot...
one more reference just in case you want to check it out...
mainconcept mpeg pro hd 4 plug in for adobe premiere url
Excelent tip....
http://www.mainconcept.com/products/apps-plug-ins/mpeg-pro-hd.html

HDMI Out From 27inch iMAC No Longer Has Audio Post Mavericks Upgrade

After upgrading to Mavericks my Mini Displayport->HDMI out is no longer outputting audio.
Is this happening to anyone else? Any line on a solution?

I am having the same issue, and have posted a reply to a similar issue in the mavericks forum.

No HDMI out to video display

I recently received a new MacBook pro 15" and 2 Dell 27" P2714H monitors. I can run a mini display port to one of the Dell Monitors, but I tried to run an HDMI to DVI Port (not mini DVI) to the other Dell Monitor, no signal...I have 2 displays working(MacBook pro + 1 Monitor). Is it possible to get the other working? Should I try HDMI out to DVI? There is a DVI port on the Dell.
Thanks

If your MBP was made before April 2010, there is no audio output from the Mini-Displayport, and you'll need to run a separate audio cable from your headphone port to the TV.

Recording from HDMI out

We have an event coming up at work and one of the presenters will be using Apple TV. I will be recording the event and want to capture the Demo from the Apple TV box to edit into the video presentation.
Is it possible to record from the HDMI out?
Does Apple offer a way to record the live stream?

Thanks for the responds...this demo will be live from what I understand. It will not be a pre-recorded or produced presentation.
I may have no choice other than recording one of the flat screen monitors.
Thanks again.

Can you use the HDMI Out and the Optical Cable out at the sametime?

I would like to connect the HDMI out cable from Apple TV to connect to the HDMI digital video/audio connection to my stereo and connect the optical out on the Apple TV and connect to my Zone 2 on the same reviever.
Can I use both these Apple TV outputs at the same time or can you only use one at a time?

Yes, lots of conflicting reports, sometimes things can change from one AppleTv firmware to another.
I had assumed PJJW12 was planning on viewing and also outputting audio to Zone 2.
I assume the AppleTv would be hooked to the Av amp - might be worth seing if the current HDMI audio could be routed to Zone 2 to avoid need for an adapter. However the AppleTV is connected if there is a TV involved and audio processing gets passed through it may also be possible to take analogue out from a TV and perhaps route that to Zone 2.

M6-n012dx HDMI out to 3840x2160 60hz?

Similar Messages

Maybe you are looking for