Mac Pro 2008 startup failure

I've replaced failed logic board in my Mac Pro 2008, but it's still not working.
When I press power button, all fans spins, GPU fan spins, but there is no chime and display.
DIAG LED shows only yellow STBY and green PWRG.
Please help !

FBDIMMs
They age, stress, heat fatigue.
You just need to use RMA and warranty once you know which pairs.
And you should be seeing errors or wrong amount or something in Memory tab in System Profile.
Apple Hardware Test will spot parity error DIMMs and some hardware issues with RAM or Risers
Rember can try to look for errors but harder with ECC.
Don't. You can end up with corrujpt files, corrupt system, corrupt directory.
All of which takes more time to find and correct.
And you may need to do a clean install and go from there.
FBDIMMs should have lifetime warranty and buy from a reputable Mac source (Crucial, OWC, Kingston etc) that says "Mac Pro certified"

Similar Messages

  • Mac Pro [2006] startup failure

    I have a Mac Pro 2.0 Ghz system which will not power up correctly. I have browsed various topics here and searched using google in the hope of finding an answer. Some of this has been helpful and I am now at the stage of replacing either the logic board or the power supply using spare parts from another chassis. Unfortunately the status of these parts is also unknown. I don't want to swap parts from my one working system and risk ending up with three dead machines!
    Anyway I have tried the SMC reset procedures, reset the RTC and replaced the battery, changed RAM riser cards and so forth to no avail. The situation still is that the machine responds to power button presses with a slight "click", the front-panel LED glows steadilly and the fans run but accelerate to very high speed over a minute or so after applying power.
    The onboard diagnostic LEDs are all extinguished and pressing the diagnostics switch results in only LED1 [trickle power] lighting up. No LED's are illuminated on the RAM risers or graphics card.
    There is no system chime.
    Keyboard appears dead but the mouse will light up if plugged into a USB port on the chassis instead of one of the ports on the keyboard.
    My spare logic board has no CPUs installed and so it will be a major job to do the changeover.
    Questions then are:
    Is there enough info here to say positively whether it is a PSU or a logic board problem?
    Are there other possibilities? Thermal sensors? GPU? Cabling faults?
    Is there any way to test a logic board or PSU in isolation from a complete system? Can the logic board be tested without CPUs installed?
    Any help would be appreciated.

    We have a 2.66 MacPro 1,1 still running fine at present, the original graphics card was replaced by Apple as part of a known issue. This was over 4 years ago, close to the end of the cutoff period for the known issue IIRC.
    I'd suggest you contact Apple & see if you can sweet talk them into doing something about the graphics card, even if it's just arranging a better price on a replacement. I recollect at the time of the exchange Apple was switching cards based on the installed OS. Having 10.6 installed meant we got a NVIDIA 8800GT, earlier OS's meant other cards were offered instead. I think it came with a NVIDIA GeForce 7300 GT (but I could be wrong - ask me to dig out details if you want to know for sure).
    P.S.
    Assuming the disk doesn't contain your user data, shutdown & remove your second HD to see if it runs any better, I find that the OS will wait for what feels like a lifetime when requesting data from a disk that has gone to sleep. SSD's change your perception, booting from one will freshen up the Mac, but won't fix the no graphics at boot issue, sorry.

  • Mac Pro 2008 Won't Start Up without Option Key

    Hi.
    I cannot start up my Mac Pro 2008 without holding down the Option key.
    My Snow Leopard internal hard drive failed, so I replaced my failed internal drive with a brand new one and put the cloned backup onto it.  I also have other internal drives and partitions with systems 10.5.6, 10.7.5, and 10.8.4.  I briefly added a Mavericks partition, but removed it.
    I THINK the problems started after the HD failure, but I'm not sure.  I added no peripherals recently, although I did add 4 gigs of RAM which were faulty and I had to replace them.  But they test fine with a memory test.
    If I Restart, the Mac comes up with a grey screen and won't boot into any system.
    If I Shut down, then Start up, I get the gray screen.
    In System Preferences, I can see every single possible Startup Drive, but no matter which one I select, the same gray screen happens on boot up.
    However, if I hold down the Option key (from startup or restart), then I can choose any startup volume and it starts just fine.
    I've run Disk Utility many times for Repair Disk and Repair Disk Permissions on every volume.  I've run Disk Warrior.  I've zapped the SMC/PRAM, etc.  I've tried starting up from external firewire drives and USB drives.  No matter which drive I select in StartUp Disk Preferences, it's the same grey screen.
    I've tried starting up with ZERO peripherals attached except for USB keyboard and mouse.
    I've taken out all startup and login items.
    I'm don't know what else to try.  I don't mind using the Option key every time, but I'm worried it's a sign of impending problems.
    Thanks!

    Barry, thanks for your reply. Yes, that's what I mean when I wrote:
    "In System Preferences, I can see every single possible Startup Drive, but no matter which one I select, the same gray screen happens on boot up."
    I selected a default startup volume in sys preferences, closed it, and restarted.  I tried every volume possible in turn.
    But thanks for doublechecking

  • Mac Pro 2008 Apple Cinema Displays are black and there are start up issues

    I have a Mac Pro 2008 Dual quad 2.8 GHz. I have two Apple Cinema Displays (graphics are the standard ATI Radeon HD 2600 – 2 dual link DVI. I have 4 2-GB RAM sticks (8 GB total).
    Neither of my displays are showing anything. Their power lights are on but they are completely black throughout the start up process. In addition when I try to boot up with both graphics cards installed, I get nothing – no beeps no chimes. If just one card is installed (either card in either slot) the computer beeps, chimes and makes the sounds of booting up, but not a flicker on the displays. RAM does not seem to be the issue as I have tried booting with several configurations of RAM sticks with no negative or positive effects. I tried booting up with Hard Drives 1 & 2 removed with no effect.  I have tried several different start up moods and have reset PRAM.
    My guess is that there is something wrong with the motherboard. Or is it possible that both graphics cards are bad?

    The "least intensive" thing you can do is hold down Alt/Option at Startup. Thsi invokes the all-in-ROM Startup Manager, which will light up the screen gray or blue, then attempt to draw an Icon for each potentially-bootable Volume attached (if any). It works as if in slow motion, so you must be patient. If no activity after about two minutes you may count that as a failure.
    The next most intensive is to attempt to boot from an incorruptible source of software, such as an Installer/Utilities DVD. This again uses the "one-size-fits-all" display driver, and attempts to load software off the DVD. The dark colored Apple is loaded off a drive -- it is not present inside your Mac.
    The next most intensive step is to attempt to boot into Safe Mode. This also uses the "one-size-fits-all" display Driver, and does a disk check as it starts up, adding five minutes to the startup time. It then drwas a login screen and deamds your username and password, even if you normally auto-login.

  • My Mac pro 2008, not running after the Apple logo, i rebooting and i rebooting

    My Mac Pro 2008 no boot afther the Logo Apple, reboot, reboot and reboot only, and in XP, the graphic is pertubed with bad graphics ... the mémory it's good, and i thinks my card graphic is out. SRY for my english, it's not my language. Help my please, my apple care is finished 10/2011, and i will repared itself. Many thanks. Alain Muno

    Not saying this IS your problem, but … I just went through avery similar problem with Mac Pro3,1. Here is my story.
    On boot of any Mac OP system drive, internal or externalHDD, (Lion or Snow Leopard), original Mac Pro install CD, Snow Leopard CD,nothing.  (Would only go to gray screen,apple logo, spinning gear that would stop spinning after about a minute.)  But, it would boot on XP drive.  However, in XP, on Windows black startupscreen, had alternating columns of two different patters of blue dots and XPgraphics were not as they should be (larger icons on desk top, slow response,different size of desk top (maybe 600x400 when it should have been1024x768).  Supplied hardware test showedno failures.  Took it to shop.  Their better diagnostics showed nofailures.  All peripherals (my drives, myCDs, etc, disconnected.  (NOTE: they didnot try a new video card since they did not have one.)  Still would not start even using their drives(external or internal).  Shop tried a newlogic board.  That did not work and theyput the original one back in.  Shop saidall they could come up with was new processors. This was not a cost effective option and they had none to try.
    After thinking about it more, I figured it could be thevideo card: the original 8800 GT that came with the Mac: that it was so bad itwould not start in Mac OS but would limp along in XP.  I was all set to buy another vid card one-bay just to try.  While doing thatresearch, came across several articles on the Internet that discussed vid cardfailure due to micro-cracks in some solder joints.  These develop due to age/heat cycles.  The proposed fix was to ‘reflow’ the solder.  Figured it was worth a try before spendingthe money on a new vid card.  Found thesedetailed instructions on youtube.  http://www.youtube.com/watch?v=T7um_hZYom4  I followed the procedure, put the vid cardback in, and now it works just fine.
    I did not and would not do this until I had ruled outeverything else.  But, it has worked forothers and it did work for me.

  • Mac Pro 2008 always crash after sleep and after first start

    Hello, new in the forum,
    2 years ago, I replaced the main disk of a Mac Pro 2008 for a SSD Samsung 470 256 Go.
    Until then, it always crashed 1 or 5 minutes after sleep mode (which I didn't used much), and not always 10 to 15 minutes after the first start of the day.
    No matter if I was working on it or not… Suitcase installed or not (no font problem here). Rest of the day was fine (if no sleep !).
    The difference of speed was so big and "good" that I dealed with it. I though that the Mac Pro was a little old for the SSD technology, and that Apple would fix it, with chance…
    2 weeks ago, I installed Maverick :
    I got crashs during the work flow too. I needed to re-start 3 times at least… Re-start without extension was ok (or not), re-start, crash, re-start without extension, restart ok. I used Onyx, did PRAM too. And sometimes, I needed to re-install Maverick or even to do a clean-install !
    So I suspected the Samsung 470 for all (sleep and work crashs) and replaced it for a Samsung 840 Pro 512 Go.
    And the Mac Pro returned to Mountain Lion.
    Not really better : no crash one day (yeeeees!) and crash after the first start the next day (nooooo!). Every time I tested sleep mode, it crashed.
    My system :
    Mac Pro 3.1 - 2,8 GHz - Quad
    Mountain Lion, 10 Go ram DDR2, ATI Radeon HD 2600 XT, 30' cinema display.
    Adobe CS5 alone (minimal install) with Onyx to repair after each crash.
    Could it be the video card, the mother board, the age of the boy ?
    Thanks a lot !
    Christophe S

    Edit !
    I said that Finder and apps were blocked after 10 seconds (without extension).
    But it was to clic on Launchpad that blocked all, and 5 minutes later it works again.
    I did clic again on Launchpad, it blocked and 2 minutes later it appeared full screen but with rainbow circle, and quit.
    - Restarted with extensions. Kernel panic!
    - Restarted the mac and the grey screen with Apple blocked, without any mouse this time. 15 minutes later, still blocked.
    - Forced restart without extension. Here are the reports of Kernel Panic and EtreCheck:
    Kernel Panic Report:
    Interval Since Last Panic Report:  122463 sec
    Panics Since Last Report:          1
    Anonymous UUID:                    52E60929-F5AE-D9CD-04B0-1872526C0821
    Mon Oct 13 10:58:17 2014
    panic(cpu 3 caller 0xffffff8007cb8945): Kernel trap at 0xffffff8007ef69e0, type 14=page fault, registers:
    CR0: 0x0000000080010033, CR2: 0x000000000000008a, CR3: 0x000000002f749000, CR4: 0x0000000000000660
    RAX: 0xffffff80209bb7e8, RBX: 0xffffff801fc6d808, RCX: 0x0000000009000000, RDX: 0xffffff801fc6dde0
    RSP: 0xffffff8131b7bbc0, RBP: 0xffffff8131b7bc00, RSI: 0x00000000000c43ff, RDI: 0xffffff801fc6dde0
    R8:  0x0000000000000000, R9:  0x0000000000000000, R10: 0xffffff80220fbfa4, R11: 0x0000000000000020
    R12: 0xffffff801fc6dde0, R13: 0x00000000000c43ff, R14: 0x00000000000c43ff, R15: 0x0000000000000002
    RFL: 0x0000000000010202, RIP: 0xffffff8007ef69e0, CS:  0x0000000000000008, SS:  0x0000000000000010
    Fault CR2: 0x000000000000008a, Error code: 0x0000000000000000, Fault CPU: 0x3
    Backtrace (CPU 3), Frame : Return Address
    0xffffff8131b7b860 : 0xffffff8007c1d636
    0xffffff8131b7b8d0 : 0xffffff8007cb8945
    0xffffff8131b7baa0 : 0xffffff8007ccebfd
    0xffffff8131b7bac0 : 0xffffff8007ef69e0
    0xffffff8131b7bc00 : 0xffffff8007eee0d6
    0xffffff8131b7be00 : 0xffffff8007d1a5d6
    0xffffff8131b7be60 : 0xffffff8007d092aa
    0xffffff8131b7bf50 : 0xffffff8007fe97ba
    0xffffff8131b7bfb0 : 0xffffff8007ccf453
    BSD process name corresponding to current thread: mdworker
    Mac OS version:
    12F45
    Kernel version:
    Darwin Kernel Version 12.5.0: Sun Sep 29 13:33:47 PDT 2013; root:xnu-2050.48.12~1/RELEASE_X86_64
    Kernel UUID: EA38B02E-2B88-309F-BA68-1DE29F605DD8
    Kernel slide:     0x0000000007a00000
    Kernel text base: 0xffffff8007c00000
    System model name: MacPro3,1 (Mac-F42C88C8)
    System uptime in nanoseconds: 121192507210
    last loaded kext at 8889944220: com.apple.driver.AudioAUUC 1.60 (addr 0xffffff7f899fe000, size 28672)
    loaded kexts:
    com.apple.driver.AudioAUUC 1.60
    com.apple.filesystems.autofs 3.0
    com.apple.driver.AppleHDAHardwareConfigDriver 2.4.7fc4
    com.apple.driver.AppleTyMCEDriver 1.0.2d2
    com.apple.iokit.IOBluetoothSerialManager 4.1.7f4
    com.apple.driver.AppleHWSensor 1.9.5d0
    com.apple.driver.AppleHDA 2.4.7fc4
    com.apple.driver.AppleUpstreamUserClient 3.5.12
    com.apple.driver.AppleMCCSControl 1.1.11
    com.apple.iokit.IOUserEthernet 1.0.0d1
    com.apple.kext.AMDFramebuffer 8.1.6
    com.apple.driver.AppleUSBDisplays 357
    com.apple.iokit.CSRBluetoothHostControllerUSBTransport 4.1.7f4
    com.apple.Dont_Steal_Mac_OS_X 7.0.0
    com.apple.ATIRadeonX2000 8.1.6
    com.apple.driver.ApplePolicyControl 3.4.5
    com.apple.driver.AppleSMBusPCI 1.0.11d1
    com.apple.driver.AppleLPC 1.6.3
    com.apple.driver.AppleMCEDriver 1.1.9
    com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
    com.apple.driver.CSRHIDTransitionDriver 4.1.7f4
    com.apple.driver.PioneerSuperDrive 3.3.1
    com.apple.iokit.SCSITaskUserClient 3.5.6
    com.apple.driver.XsanFilter 404
    com.apple.iokit.IOAHCIBlockStorage 2.3.5
    com.apple.driver.AppleUSBHub 635.4.0
    com.apple.driver.AppleIntel8254XEthernet 3.1.1b1
    com.apple.driver.AppleFileSystemDriver 3.0.1
    com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
    com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
    com.apple.BootCache 34
    com.apple.driver.AppleFWOHCI 4.9.9
    com.apple.driver.AppleAHCIPort 2.6.6
    com.apple.driver.AppleIntelPIIXATA 2.5.1
    com.apple.driver.AppleUSBEHCI 621.4.6
    com.apple.driver.AppleUSBUHCI 621.4.0
    com.apple.driver.AppleACPIButtons 1.8
    com.apple.driver.AppleRTC 1.5
    com.apple.driver.AppleHPET 1.8
    com.apple.driver.AppleSMBIOS 1.9
    com.apple.driver.AppleACPIEC 1.8
    com.apple.driver.AppleAPIC 1.7
    com.apple.driver.AppleIntelCPUPowerManagementClient 214.0.0
    com.apple.nke.applicationfirewall 4.0.39
    com.apple.security.quarantine 2.1
    com.apple.driver.AppleIntelCPUPowerManagement 214.0.0
    com.apple.kext.triggers 1.0
    com.apple.iokit.IOSerialFamily 10.0.6
    com.apple.driver.DspFuncLib 2.4.7fc4
    com.apple.iokit.IOAudioFamily 1.9.2fc7
    com.apple.kext.OSvKernDSPLib 1.12
    com.apple.driver.AppleSMBusController 1.0.11d1
    com.apple.iokit.IOSurface 86.0.4
    com.apple.iokit.IOBluetoothFamily 4.1.7f4
    com.apple.iokit.IOBluetoothHostControllerUSBTransport 4.1.7f4
    com.apple.iokit.IOFireWireIP 2.2.5
    com.apple.driver.AppleHDAController 2.4.7fc4
    com.apple.iokit.IOHDAFamily 2.4.7fc4
    com.apple.driver.AppleGraphicsControl 3.4.5
    com.apple.iokit.IONDRVSupport 2.3.7
    com.apple.kext.AMD2600Controller 8.1.6
    com.apple.kext.AMDSupport 8.1.6
    com.apple.iokit.IOGraphicsFamily 2.3.7
    com.apple.driver.AppleSMC 3.1.5d4
    com.apple.driver.IOPlatformPluginLegacy 1.0.0
    com.apple.driver.IOPlatformPluginFamily 5.4.1d13
    com.apple.driver.AppleUSBHIDMouse 175.8
    com.apple.driver.AppleHIDMouse 175.8
    com.apple.driver.AppleUSBHIDKeyboard 170.2.4
    com.apple.driver.AppleHIDKeyboard 170.2.4
    com.apple.iokit.IOUSBHIDDriver 623.4.0
    com.apple.driver.AppleUSBMergeNub 621.4.6
    com.apple.driver.AppleUSBComposite 621.4.0
    com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.5.6
    com.apple.iokit.IOBDStorageFamily 1.7
    com.apple.iokit.IODVDStorageFamily 1.7.1
    com.apple.iokit.IOCDStorageFamily 1.7.1
    com.apple.iokit.IOATAPIProtocolTransport 3.5.0
    com.apple.iokit.IOSCSIArchitectureModelFamily 3.5.6
    com.apple.iokit.IOUSBUserClient 630.4.4
    com.apple.iokit.IOFireWireFamily 4.5.5
    com.apple.iokit.IOAHCIFamily 2.5.1
    com.apple.iokit.IONetworkingFamily 3.0
    com.apple.iokit.IOATAFamily 2.5.1
    com.apple.iokit.IOUSBFamily 635.4.0
    com.apple.driver.AppleEFINVRAM 2.0
    com.apple.iokit.IOHIDFamily 1.8.1
    com.apple.driver.AppleEFIRuntime 2.0
    com.apple.iokit.IOSMBusFamily 1.1
    com.apple.security.sandbox 220.3
    com.apple.kext.AppleMatch 1.0.0d1
    com.apple.security.TMSafetyNet 7
    com.apple.driver.DiskImages 345
    com.apple.iokit.IOStorageFamily 1.8
    com.apple.driver.AppleKeyStore 28.21
    com.apple.driver.AppleACPIPlatform 1.8
    com.apple.iokit.IOPCIFamily 2.8
    com.apple.iokit.IOACPIFamily 1.4
    com.apple.kec.corecrypto 1.0
    Model: MacPro3,1, BootROM MP31.006C.B05, 8 processors, Quad-Core Intel Xeon, 2.8 GHz, 10 GB, SMC 1.25f4
    Graphics: ATI Radeon HD 2600 XT, ATI Radeon HD 2600, PCIe, 256 MB
    Memory Module: DIMM Riser B/DIMM 1, 2 GB, DDR2 FB-DIMM, 800 MHz, 0x02FE, 0x47523244463247425838454C3830304E3252
    Memory Module: DIMM Riser B/DIMM 2, 2 GB, DDR2 FB-DIMM, 800 MHz, 0x02FE, 0x47523244463247425838454C3830304E3252
    Memory Module: DIMM Riser A/DIMM 1, 1 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x48594D5035313241373243503844332D5335
    Memory Module: DIMM Riser A/DIMM 2, 1 GB, DDR2 FB-DIMM, 800 MHz, 0x80AD, 0x48594D5035313241373243503844332D5335
    Memory Module: DIMM Riser A/DIMM 3, 2 GB, DDR2 FB-DIMM, 800 MHz, 0x02FE, 0x47523244463247425838454C3830304E3252
    Memory Module: DIMM Riser A/DIMM 4, 2 GB, DDR2 FB-DIMM, 800 MHz, 0x02FE, 0x47523244463247425838454C3830304E3252
    Bluetooth: Version 4.1.7f4 12974, 3 service, 12 devices, 0 incoming serial ports
    PCI Card: ATI Radeon HD 2600, sppci_displaycontroller, Slot-1
    Serial ATA Device: Samsung SSD 840 PRO Series, 512,11 GB
    Serial ATA Device: ST31000524AS, 1 TB
    Parallel ATA Device: PIONEER DVD-RW  DVR-112D
    USB Device: hub_device, apple_vendor_id, 0x9120, 0xfd500000 / 2
    USB Device: Keyboard Hub, apple_vendor_id, 0x1006, 0xfd520000 / 4
    USB Device: Apple Optical USB Mouse, apple_vendor_id, 0x0304, 0xfd521000 / 6
    USB Device: Apple Keyboard, apple_vendor_id, 0x0221, 0xfd522000 / 5
    USB Device: Apple Cinema HD Display, apple_vendor_id, 0x9220, 0xfd530000 / 3
    USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x8206, 0x5d200000 / 2
    FireWire Device: built-in_hub, 800mbit_speed
    FireWire Device: unknown_device, unknown_speed
    Report EtreCheck :
    Description du problème :
    Here is the report of EtreCheck after the Kerner Panic sent before.
    Christophe.s
    EtreCheck version : 2.0.2 (86)
    Rapport créé 13 octobre 2014 11:23:31 UTC+02:00
    Informations matérielles : ℹ️
      Mac Pro (début 2008)
      Mac Pro - modèle : MacPro3,1
      2 2.8 GHz Quad-Core Intel Xeon CPU : 8-core
      10 GB RAM Pas extensible
      DIMM Riser B/DIMM 1
      2 GB DDR2 FB-DIMM 800 MHz ok
      DIMM Riser B/DIMM 2
      2 GB DDR2 FB-DIMM 800 MHz ok
      DIMM Riser A/DIMM 1
      1 GB DDR2 FB-DIMM 800 MHz ok
      DIMM Riser A/DIMM 2
      1 GB DDR2 FB-DIMM 800 MHz ok
      DIMM Riser B/DIMM 3
      empty empty empty empty
      DIMM Riser B/DIMM 4
      empty empty empty empty
      DIMM Riser A/DIMM 3
      2 GB DDR2 FB-DIMM 800 MHz ok
      DIMM Riser A/DIMM 4
      2 GB DDR2 FB-DIMM 800 MHz ok
      Bluetooth: Vieux - Handoff/Airdrop2 pas disponible
    Informations vidéos : ℹ️
      ATI Radeon HD 2600 - VRAM : 256 MB
      Cinema HD Display 2560 x 1600
    Logiciel du système : ℹ️
      OS X 10.8.5 (12F45) - Uptime: un jour 0:11:6
    Informations des disques : ℹ️
      Samsung SSD 840 PRO Series disk0 : (512,11 GB)
      Statut S.M.A.R.T. : Vérifié
      disk0s1 (disk0s1) <non monté>  : 210 Mo
      MacPro SSD (disk0s2) /  [Startup] : 511.25 Go (472.61 Go libre)
      Recovery HD (disk0s3) <non monté>  [Restauration] : 650 Mo
      ST31000524AS disk1 : (1 TB)
      Statut S.M.A.R.T. : Vérifié
      disk1s1 (disk1s1) <non monté>  : 210 Mo
      MacPro 1To (disk1s2) /Volumes/MacPro 1To  : 999.35 Go (633.08 Go libre)
      Recovery HD (disk1s3) <non monté>  [Restauration] : 650 Mo
    Informations USB : ℹ️
      Verbatim Portable USB Drive 320,07 GB
      Statut S.M.A.R.T. : Vérifié
      disk3s1 (disk3s1) <non monté>  : 210 Mo
      320 Go Christophe Syren (disk3s2) /Volumes/320 Go Christophe Syren  : 319.73 Go (313.64 Go libre)
      USB 2.0 USB Flash Drive 8,17 GB
      Statut S.M.A.R.T. : Vérifié
      SANS TITRE (disk2s1) <non monté>  : 8.17 Go
      Apple, Inc. Keyboard Hub
      Mitsumi Electric Apple Optical USB Mouse
      Apple, Inc Apple Keyboard
      Apple Inc. Bluetooth USB Host Controller
    Gatekeeper : ℹ️
      Mac App Store et développeurs identifiés
    Représentants de lancement : ℹ️
      [désengagé] com.adobe.AAM.Updater-1.0.plist Aide
      [désengagé] com.adobe.CS5ServiceManager.plist Aide
      [désengagé] com.extensis.FMCore.plist Aide
    Daemons de lancements : ℹ️
      [invalid?] com.adobe.SwitchBoard.plist Aide
    Représentants de lancement pour l’utilisateur : ℹ️
      [désengagé] com.adobe.AAM.Updater-1.0.plist Aide
      [désengagé] com.adobe.ARM.[...].plist Aide
    Éléments Ouverture : ℹ️
      iTunesHelper Application (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
      Dropbox Application (/Applications/Dropbox.app)
    Plug-ins internet : ℹ️
      OfficeLiveBrowserPlugin : Version : 12.3.6 Aide
      AdobePDFViewer : Version : 9.5.5 Aide
      QuickTime Plugin : Version : 7.7.1
      JavaAppletPlugin : Version : 14.9.0 - SDK 10.7 Vérifier la version
    Panneaux de préférences de 3ème partie : ℹ️
      Growl  Aide
    Time Machine : ℹ️
      Skip System Files: NO
      Sauvegarde automatique : OUI
      Disques sauvegardés :
      MacPro SSD : Taille de disque : 511.25 Go Disque utilisé : 38.64 Go
      Destinations :
      Data [Network]
      Taille totale : 2 To
      Nombre de sauvegardes total : 9
      Sauvegardes la plus agée : 2014-10-08 01:39:21 +0000
      Dernière sauvegarde : 2014-10-10 11:31:35 +0000
      Taille de la disque de sauvegarde : Excellent
      Taille de sauvegarde 2 To > (Taille de disque 511.25 Go X 3)
    L’utilisation du CPU par processus : ℹ️
          1% WindowServer
          0% ps
          0% fontd
          0% System Events
          0% coreservicesd
    L’utilisation de la mémoire par processus : ℹ️
      97 Mo Dock
      97 Mo Finder
      75 Mo WindowServer
      64 Mo com.apple.security.pboxd
      64 Mo CalendarAgent
    Informations de la mémoire virtuelle : ℹ️
      523 Mo RAM Disponible
      1.04 Go RAM Active
      307 Mo RAM Inactive
      8.86 Go RAM Résidente
      266 Mo Pages entrants
      0 o Sorties pages

  • Apple Mac Pro 2008 dual 2.8ghz quad core

    Hey guys,
    Ive got a real brain teaser. I have a apple mac pro 2008 dual 2.8ghz quad core that wont boot.
    The leds on the memory test good its all tested in another mac and working well.
    The 9 leds are reading as follows 2nd led lit yellow. Led 9,8,7 Green- which from my research is good.
    Ive also reset the cmos battery and vram, nothing.
    Pulled the memory and video card and re-seated them also nothing.
    The last thing i tryed was shut the computer down sit for 30 seconds then held alt and got the install mac os screen not a hard drive option.
    Which leads me to think its not seeing the hard drive?
    Any suggestions?

    Starts up with fans
    Makes the apple chime
    The chime is generated in software when the first portion of the power-on self test has passed.Your Mac is working and has enough working RAM memory to start up.
    You still may have problems with drives, the software on those drives, or your graphics card.
    apple logo comes up
    The dark gray Apple is loaded by the ROM boot loader in the first blob of software (before the file system is initialized). Its presence indicates your Mac can get some stuff off a Hard Drive, and seeing it indicates your graphic card can display something in a primitive way.
    with spinning gear and just sits there for hours
    It is stuck booting up something. Verbose Mode (hold Command-V at startup) will show you the parade of messages. The last five will tell you what happened.

  • Cannot install Vista Ultimate 64bits on Mac Pro 2008

    Hello,
    I'm trying to install Vista Ultimate 64bits on my new Mac Pro (2008, 2x Quad Core, 3x 500GBHDD, 16 GB Ram), but Vista is unable to find a correct partition type.
    The first thing I did was to install a 4th HD, and I constantly received an error 0x80004005 which seems to be too generic.
    Then I tried to install it on the 3rd HD (Bay 2 is where my OS X startup disk is located btw) but here no way neither....Windows cannot find a valid partition.....
    I tried to partition it manually in MBR...same problem....
    Then with BootCamp assistant...same problem...
    I also tried to use Vista Business 64 SP1, same problem...
    Do you have any idea ?
    Thanks,
    Patrick

    Hello,
    Thanks for your answer, but unfortunately I'm still stuck...
    To resume the situation :
    I put a brand new 250GB SATA in the bay 4.
    I start Bootcamp Assistant and tell him that I want to use this new disk for Windows and then start Vista x64 install.
    Vista sees 2 partitions on this new disk :
    Disk 3 Partition 1 : 200 MB (Primary)
    Disk 3 Partition 2 : 230 GB (Primary)
    If I try to use the P2 for the install, I have to format it first. Once formatted, Vista says : This computer's hardware may not support booting to this disk. Ensure that the disk controller is enabled in the computer's BIOS menu.
    If I try to use the 200 MB (just for fun..), then I also have to format it, but here I receive the error message 0x8000xxxx
    So clearly I'm lost...
    Could it be related to the 16 GB RAM ? Too much for Vista ?? I don't believe as this is Vista x64...
    Thanks for your help, ideas..
    Patrick

  • Adding USB 2.0 ports to a Mac Pro 2008

    Hi,
    I love my Mac Pro 2008! Great machine, awesome performance, but I need more ports Who needs only three USB ports in the back, that's a joke!
    Anyways, I just bought 2 StarTech 6-port USB 2.0 PCI cards from an online vendor, but quickly found out that it didn't fit my Mac. The description of the card even says it is compatible with Mac OS X. I suspect that Apple have changed the PCI slots for something else in the Mac Pro 2008. What are they and can we buy USB card that fit those slots? If so where? I am desperate for more ports.

    You may have stumbled upon or checked some of the support pages?
    http://www.apple.com/support/macpro/
    - which has a link to an article titled "about your PCI Express slots"
    http://docs.info.apple.com/article.html?artnum=304122
    Specs 2008: http://support.apple.com/kb/SP11:
    PCI Express expansion7
    Three open full-length PCI Express expansion slots
    One PCI Express 2.0 x16 slot
    Two PCI Express x4 slots
    And of course support for up to four PCI Express video cards; Fibre Channel; Mac Pro RAID.
    You could install a powered USB hub, or FW/USB2, as long as you have free slots for more. I have FW800, a 1x Sonnet Tempo (couple storage drives), and a 4x Tempo (multiple RAID sets; Port Multiplier card and multi-drive enclosures and 4 channels).

  • I install LION on my mac pro 2008 and it's alway's pop with " there was a problem connecting to the server " Time Capsule" .How can i remove this popup. My Time machine is working fine and also rename it. But the popup keeps on coming with the old name.

    I installed LION on my mac pro 2008 and it's alway's pop with " there was a problem connecting to the server " Time Capsule" .How can i remove this popup. My Time machine is working fine and also rename it with less than 7 karakters. But the popup keeps on coming with the old name.

    I have a BT Infinity router plugged into the Time Capsule, not sure where the radio settings are?
    They are able to use the network settings of the TC i.e. they can connect to the internet via the wifi through the TC but when they try and connect to the AirPort Disk this is where it is not allowing a connection.
    I don;t have the drive shared out at all at the moment, is this necessary?  How do I do this if so?
    I have attached the screen shots of all the settings.
    Thanks again for your help.

  • Mac Pro 2008 - upgrade to 2010 model or not?

    I have a Mac Pro 2008 2.8 gHz with 12GB RAM. I'm not running Premiere Pro CS5 which is great and seems to love RAM and processor speed. I also recently got a CUDA card to take advantage of it's GPU acceleration.
    My question is: Should I get a new Mac Pro 2010, 6, 8, 12 core or just upgrade my RAM to say, 24GB and perhaps get some SSDs (maybe even in a RAID 0) as my boot drive.
    The RAM upgrade will be in the $650 range, SSDs could be at least that. I'll need RAM anyway for a new model as my old RAM isn't compatible.
    Getting a new model could set me back $5000 (or more) when it's all loaded.
    I'm also a little disappointed in the 2010 Mac Pros, for example my 2008 Mac pro was a no-brainer, but now I'm ambivalent about this upgrade to 2010, thinking there may be new models out this year that fill in all the holes. I kind of feel like the 2010 Mac Pro upgrade was a little like the Final Cut Pro 7 upgrade, it was a stop gap because Apple needed to do something. I could be wrong about this though.
    I know this is kind of a difficult question to answer, but if you have any opinions, please feel free to lend any advice.

    PCIe 3.0
    USB3
    Intel SATA3 6G
    Socket LGA1356
    Socket LGA2011
    3G SSD (by the time 4th Gen SSDs are out, one unit would make out our current SATA channel bandwidth)
    Mid-range Xeon roadmap:
    Socket LGA1356, a direct replacement for the current Socket LGA1366. The parts here are 6-core and 8-core Sandy Bridge single-socket and dual-socket capable but mid-range positioned Sandy Bridge Xeon - and, ultimately, Core i7 - parts with up to 20MB of L3 cache, three DDR3-1600 memory channels just like the existing LGA1366 Westmeres with one memory speed grade higher, and 24 PCIe v3 lanes on-chip.
    The single external QPI v2 link runs at up to 8 gigatransfers/sec, or 32GB/sec bidirectional bandwidth, a 25 per cent speed up over the current generation, but also feeding a third more cores on each socket.
    http://www.theinquirer.net/inquirer/feature/1811091/2011-intel-xeon-update-holy- socket-trinity
    Intel is set to replace its current high-end socket, LGA1366, when it releases its new 8-cores processors in the Late 2011. This socket is expected to be released alongside Sandy Bridge-EX in Q3 2011, and will support 4 memory channels as well as 40× PCIe 3.0 lanes.
    http://en.wikipedia.org/wiki/LGA_2011

  • Mac Pro 2008 won't boot from install disc - black screen

    Hello,
    I recently purchased a new hard drive to replace the original that came with my Mac Pro 2008.  I was able to format the new drive using Disk Utility. I am now at the point where I need to install OS X onto the new drive, but the computer refuses to boot from the disc. The disc is recognized by the computer (I can access the disc and am able to use the BootCamp applications, etc.) but I just get a black screen when trying to boot directly from the disc. The computer boots fine otherwise.
    I have tried the following:
    I have tried using both the gray install disc that came with the computer and the Snow Leopard Install DVD disc.
    I have tried booting using the "C" key and the "option" key but still receive a black screen following the chime (I've held these down for several minutes).
    I have tried restarting from either install disc using the Bootcamp Assistant.
    I have tried running the installation software to get it to restart from the disc.
    I have tried a combination of the drives, i.e. trying to boot from the discs with just the new drive installed, just the original drive installed, and with both in bay1 and 2.
    Everything results in the computer starting up, hearing the chime, and then nothing..just black screen. I have the original drive partitioned with BootCamp with OSX Snow Leopard and Windows 7 installed (I don't know that that matters).
    I am at a loss as to what to try next. It doesn't seem like the superdrive because it is recognizing the disc, it just won't boot from it.
    Any help is appreciated, thank you.

    Clone should be a must  and easy to do and learn (learn by doing! 2)
    6800 would 'qualify' as 5x70 series flashed etc and same rule: 10.6.5
    In the past there was 10.4.6, 10.5.6, but not 10.6.6 - even though strong need for such a DVD.
    10.6.8 DVD would  be excellent
    Lion or ML - buy, download, make an installer flash card would be what I would do at this point.
    Then keep both - dual boot as you learn and test and see what ML does and waht you had that required Rosetta to support PowerPC. See www.roaringapps.com about that.
    With Carbon Coyp Cloner - was share, now commercial, great utility been around since 10.2.2 at least - this time 2003. 10 yrs.
    You can clone the system folders, you can even selectively choose. You can skip copy of most of your home account and do that separately to another drive if  you want.
    Clone Windows with Paragon or WinClone and use Windows 7 or 8 DVD to do a system repair (automatic) or to edit the BCD file. It can and should - and all you do is boot Windows 7 DVD w/ only the one drive present and go at it. Piece of cake. But yes, Windows gets fussy if you change or remove or move. BCD to the rescue. A proper program for cloning like Paragon's "Clone OS" meant for going from disk drives to SSDs, knows that and how to do it.
    Back to how to clone etc:
    Clone
    Disk utility has RESTORE which will also clone your system but not the Lion Recovery partition. Oddly  Apple did not 'endorse' making bootable clone of the system which works too but most choose Carbon Copy Cloner - it works more consistently; it allows for smart update of the backup volume. Both can backup to a sparse disk image if desired.
    Using Cloning as a Backup Strategy
    http://www.macupdate.com/app/mac/7032/carbon-copy-cloner 
    http://www.bombich.com/software/updates/ccc-3.5.html
    OS X Lion Install to Different Drive
    How to create an OS X Lion installation disc MacFixIt
    Migration Assistant Update for Mac OS X Snow Leopard
    http://www.apple.com/support/lion/installrecovery/
    Create an OS X Lion Install disc
    http://reviews.cnet.com/8301-13727_7-20080989-263/how-to-create-an-os-x-lion-ins tallation-disc
    How to clone your system:
    http://macperformanceguide.com/Mac-HowToClone-backup.html
    http://macperformanceguide.com/Mac-HowToClone.html
    http://www.macupdate.com/app/mac/7032/carbon-copy-cloner
    http://www.macperformanceguide.com/blog/2012/20120711_2-MacPro-internal-clone-ba ckup.html
    The DVD is dependent on your hardware. And your hardware changed. The drivers for the 5780 and 6xxx are bundled in the OS and lacking. Minimum build thing.
    Put the new drive anywhere you want. Does not matter. Can move it later. Can be drive bay 0-3 or a Firewire external or under the DVD drive.
    When you clone pull the old drive and boot from the newly cloned.
    After that keep a backup clone around all the time. Takes less than 10 minutes to do a smart update to copy just the changes to keep it current. So you have working copy of the system. I keep Clone "A" that I keep "as was" the system as of last month or whatever (like 10.7.4 before upgrade to 7.5).
    Comes easier after doing it once and have all your ducks in a row.

  • Mac Pro 2008 Can't start Windows 7 / 8 Installer

    I'm trying to load Windows 8 (And have previously tried everything with Windows 7) on my Mac Pro early 2008 with Mountain Lion, and cannot get the installers to initiate.
    When I start the bootcamp assistant and reboot, my mac freezes before ever getting to the installer. When I reboot and hold option to manually select the installer, it freezes as soon as I select it. I've tried this from a DVD, USB, and even an install partition i setup on my HD, all with the same freezing results. This is a legitimate copy of Windows 8 system builder I'm working with and have installed it perfectly in Parallels.
    I should note I upgraded my video card a long time ago to a gt 120, so I'm wondering if the video card might be the problem. I've installed Windows 7 with this video card in the past so I'm guessing this is a Mountain Lion/Bootcamp 5 issue.
    Has anyone else with a Mac Pro 2008 succesfully installed Windows 7/8 from Mountain Lion/Bootcamp 5?
    Any input would be immensely appreciated!

    There are no Windows 8 Bootcamp drivers. Windows 8 is not supported.
    Use Parallels or Fusion to install Windows 8. By doing so you eliminate the need for drivers since the virtual machine creates virtual hardware and drivers.
    Once the Windows 8 Bootcamp drivers are developed and released you can then install using Bootcamp Assistant.
    Read this forum. Some people are posting that they had some success with the Bootcamp install. but if you have to rely on your computer then don't take the chance.

  • Hi, i have a A1186 Mac Pro 2008 Tower. Im running windows 7 64Bit on it. Im not sure about what version of bootcamp should i use to get the drivers. Someone please help me.

    Hi, i have a A1186 Mac Pro 2008 Tower. Im running windows 7 64Bit on it. Im not sure about what version of bootcamp should i use to get the drivers. Someone please help me.

    Boot Camp support:
    http://www.apple.com/support/bootcamp/
    Boot Camp FAQ:
    http://support.apple.com/kb/HT5639?viewlocale=en_US

  • Mac Pro 2008 or iMac 27 i7 ? Which to choose?

    I am looking to upgrade to a faster Mac from my current Macbook Pro and decided either on an iMac 27 inch i7 2.8 GHz 8 Gigs RAM 4870 Video card or buy a used Mac Pro 2008 with 2 x 2.8GHz 4 Core (8 core total) with 10 Gigs RAM and an 8800GT video card.
    Both come to almost the same price. Problem is I don't know which to get. The system will be used mainly for software development, running windows 7 and linux as Virtual Machine, some light gaming, and music (sampling, etc)
    I love the iMac's LED screen and the i7 certainly is fast but love the Mac Pro's expandability in terms of hard drives and memory and I would use it on my 30 inch LCD. That said, would I ever go past the Mac Pro's configuration of 2 TB's of drives (maybe) and more than 10 Gigs RAM (don't know)? You're stuck with the iMac in terms of hard drives forced to add slow external cases.
    The Mac Pro is over 2 years old at this point but I know the Mac Pro is a work horse and the iMac has had issues.
    Anyone have an opinion on this? Might it be worth saving some more cash (although would take another 6 months) and getting a 2009 Mac Pro?
    Let me know...

    Asked a lot and the new iMac makes it look better, but not for triple boot unless you stict to VMs most of the time. The freedom of having alternate OSs on their own drives and such.
    AppleInsider gave the high end iMac makes sense if you go that route, and if you would need a monitor as well?
    Barefeats has posted a number of tests of the iMacs
    http://www.barefeats.com
    Even the 2009 $2149 4-core is no slouch and easier to find and work with.
    At that price, you are close to the 2010. So wait another 36 hrs.
    http://www.apple.com/macpro/specs.html
    http://www.barefeats.com/nehal17.html
    Apple Specials change during the day, they disappear quickly.
    http://store.apple.com/us/browse/home/specialdeals/mac/mac_pro

Maybe you are looking for