Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?

Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?
Unfortunately do not know the operating system since I never updated anything and I can't get in to it.
Thanks for your assistance.

If you want to preserve the data on the boot drive, and it's not already backed up, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data, you can skip this step.
There are several ways to back up a Mac that is not fully functional. You need an external hard drive to hold the backup data.
1. Boot from the Recovery partition or from a local Time Machine backup volume (option key at startup.) Launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
2. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
3. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.

Similar Messages

Macbook won't boot past grey screen with Apple logo and spinning wheel.

For some reason, after about 1 year and 10 months of owning my Macbook, it decided this morning not to load past the grey screen with the Apple logo and spinning cog/wheel.
I used it for a couple of hours beforehand, and it was working fine. Software Update prompted me of about about 4 or 5 updates; I can't remember exactly what was downloaded, but I think there was a Security Update and iTunes among them. I restarted, left it to install with no errors, but when I logged in, Safari and iTunes were running incredibly slowly. I also noticed that the volume keys weren't responding, as well as the power key to bring up the "Sleep, Restart, Shutdown, etc" dialog box. I forced shutdown, hoping a restart would solve my problem, and that's when my troubles started. I originally just left it, but after about an hour the wretched thing was still spinning.
So far, I have done a number of troubleshooting tips on a variety of websites. I have tried taking the battery out and holding down power for 5 seconds, resetting the PRAM with option, cmd, p & r, and holding down power until the sleep light flashes rapidly and the computer lets out a large "BOOOP".
I have booted off my Leopard install disk with both option and c, repaired the hard drive a number of times, with there being no errors whatsoever. I have tried repairing permissions, but everything seems to freeze up, except the mouse.
For some reason my computer will not boot into safe mode, either, and holding cmd & s at startup doesn't get me to the stage where I can enter commands with the keyboard.
Unfortunately, because of my puny 60GB hard drive, I only have 1GB of free space left and cannot reinstall Leopard without wiping my hard drive.
I would greatly appreciate it if anyone could assist me with this unfortunate dilemma. It's such a shame that my computer has been fantastic for so long and now decides to play up. (Maybe it's just Apple trying to get me to buy a new 2.4Ghz aluminium Macbook sooner than I was planning...)
Thanks very much.

Hi ds,
Sorry to hear you're having such trouble!
Unfortunately, the best thing you can do at this point is reinstall Leopard (and then attempt to install the combo updater, too). If you don't have a backup of your machine, you could boot it into Target Disk Mode (by holding down T at startup) and then attach it via FireWire to another computer to salvage your files.
I recently had to repair a machine with this exact same problem, and after messing around with that for several hours, I'd have to say that I think that an Erase and Install is the way to go. If you then migrate over your user data and start having troubles, you at least know where the problem lies. I suspect, though, that having a clean machine with all of the new updates applied will be the end of the issue.
Sorry to be the bearer of bad news. There are a few other things you could try first; you could, for example, manually download the relevant combo updater from Apple's website and attempt to install it to your damaged machine while it's in Target Disk Mode. If you have a copy of Disk Warrior, that too is certainly worth a shot (and in some cases may be the saving grace). In my experience, though, a failure of this magnitude isn't easy to resolve.
Hope that helps.
—Hazy

My macbook pro doesn't bootbeyond the grey screen with apple icon and spinning wheel.

My macbook pro doesn't boot beyond the grey screen with apple icon and spinning wheel. I used the "Option" button to access the Disk Utility function and run Repair Disk and Repair Disk Permissions. Should I restart my computer?

The following support article is somewhat outdated. Where it refers to booting from an installation disc, you should boot from your recovery partition (if running 10.7 or later) by holding down the key combination command-R at the chime.
Mac OS X: Gray screen appears during startup

My MacBook Pro is stuck on grey loading screen with apple logo and spinning wheel.

PLEASE HELP - Tried to start up my MacBook Pro and I get grey screen w/ apple logo & spinning wheel. It's stuck on this screen. Safe mode didn't help but reveled this: smc read key action error, BOOS key failed, BOPS key failed. Consider rebuild of prelinked kernal com.apple.kext triggers triggered rebuild. IOBluetooth host controller USB transport Suspend Device. I ran verifications/repairs in Disk Utilities, but nothing came back wrong on the reports. I'm a bit panicked, as I use this computer for work and have no other computer to use in the meantime. I should also note that I have very little technical knowledge, so if you can lend your help please keep that in mind when responding. I'd be over the moon if anyone can help.

Startup - Gray, Blue or White screen at boot, w/spinner/progress bar
Startup - Gray Screen
Startup Issues - Resolve
Startup Issues - Resolve (2)

Macbook Pro won't boot past grey screen with Apple logo and then shuts off

This is a long story...
This morning, I would turn it on and it'd go to the grey screen with the Apple logo for a few seconds and then go to the icon that is a circle with a line through it. After reading online, I was able to boot it up in Safe Mode. I messed around a little bit in system preferences thinking I could fix it on my own, not really knowing what I was doing (I'm a *******). I went to Startup Disk in Preferences. I chose the MAC OS X, xxxx and then clicked the lock to prevent further changes and then clicked restart.
Now when I turn on the macbook, it goes to the grey screen with the Apple logo for at least two-three minutes and then just shuts off. Won't boot into Safe Mode now. Please help. I already tried the Command-Option-P-R keys trick like five times.

If you have a full retail DVD for 10.6 you can boot from that by holding the C key during startup...but you will then be in install mode if that is what you want to do. At least go ahead and see if it will boot ok from the 10.6 disk and then you can decide what you want to do further.
Apple does not have 10.5 for sale anymore from what some other users have said on here so if you want to go that route you will have to find a copy for sale such as from eBay or one of the Mac resellers.
Before taking the machine to someone, try booting from 10.6 and see if that works...that way you can narrow down problems the machine may be having.

My macbook shows a only white screen with apple logo and spinning wheel when i on the power button? How can i correct that?

Any help!!!

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 8
This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. Both desktop and portable Macs used to have such a battery. The logic-board battery is separate from the main battery of a portable. A dead logic-board battery can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. If you can't get to an Apple Store, go to another authorized service provider.

My macbook pro 2011 shows grey screen with apple logo and want start

i was just using my macbook pro and it freezed for a while not responding and i turned it off by pressing the power button. afterwards, i turn it on and it shows a grey screen with apple logo but want start pls somebody help me because am having "my life" on the machine

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
A dead logic-board battery in a Mac Pro can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

I have snow leopard installed as an OS. When trying to reboot a MacBook Pro I am getting stuck on grey screen with apple logo and rotating symbol. What can I do?

I have snow leopard installed as an OS. When trying to reboot a MacBook Pro I am getting stuck on grey screen with apple logo and rotating symbol. What can I do?

Maybe this might help.
http://support.apple.com/kb/TS2570

Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

Try the tips listed here Mac OS X: Gray screen appears during startup - Apple Support

MacBook will not start. I have restarted with original CD. I have used Utilities and "no problem" with hard drive. I have reset PRAM. I have tried safe boot. Nothing is work. Gray screen with Apple logo and rotating wheel. Thanks for any suggestions!

MacBook will not start. I have restarted with original CD. I have used Utilities and "no problem" with hard drive. I have reset PRAM. I have tried safe boot. Nothing is work. Gray screen with Apple logo and rotating wheel. Thanks for any suggestions!

Snow Leopard is a Mac OS X version. You say that it's the version you have in your Mac (10.6.8). Do a back up of your files, format the hard drive (using Disk Utility) and reinstall again

MacBook pro bought in 2010 when u turn it on screen is gray with apple logo and spinning wheel and won't turn on???

When trying to turn on MacBook pro bought in 2010 (Mac OS X) I get a gray screen with an apple logo and a spinning wheel. Won't go any further. Any ideas? I have photos I haven't saved and don't want to loose them.

stevesurplus wrote:
and a few other suggested solutions and they have not worked?
What are the 'other suggested solutions'?
Ciao.

2011 Macbook Pro white screen after apple logo and spinning wheel

Hey there guys,
My 2011 Macbook Pro has encountered some problems. Firstly while i was at school, i opened up my computer, usually the computer would require you to type your password, but my login page became fuzzy, white lines everywhere. So I restarted my computer and everything was okay. After that i came back home, my computer was running fine, after surfing the net for a few hours, my whole computer suddenly became blue. So what i did was i just restarted my computer, after that my computer would boot up Apple logo would come up, the spinning wheel would also come up, after 30-40 secs it would turn black screen and come back on as a white screen and would just stay like that. It would be on the white screen. Tried some rebooting ways but all didn't work.
1st: I wanna know whats the problem?
2nd: Is this a harddrive failure? (Because i have alot of important documents and personal stuff in my hard drive and i hope it isn't a crashed hardrive)
Thanks for your help..
PS: Im running on Moutain Lion, but i have no idea what version it is.

Make a "Genius" appointment at an Apple Store.
Back up all data on the internal drive(s) before you hand over your computer to anyone. If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
Keeping your confidential data secure during hardware repair
*An SSD doesn't need to be zeroed.

My mac froze in an application so I shut it down by powering off with button, now when I try to turn it on I have a grey screen with Apple loge and the timer swirling but it doesn't get past this, please help!

I Shut down my Mac by holding in the power button after my iMac froze and now when I try to turn it back it on all I get is the grey screen with Apple loge and the timer and doesn't get any further. I have tried the diagnostic test but nothing was found.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

MacBook pro 15" 2008 freezes at apple logo and spinning wheel

Have a MacBook pro early 2008 have installed lion but recently started to have problems. Started to freeze a lot so I would restart and most of the time it would work untill it froze again , now it's got worst every time I restart my Mac it won't go past apple logo and spinning wheel just freezes have been trying and trying but same thing freezes. Tried to start in save mode but no still freezes
Please has anyone got any suggestions thanks

The startup disk may need repairing.
Use Lion Recovery
Not enough free space on the startup disk can cause the system to freeze.
Right or control click the MacintoshHD icon. Click Get Info. In the Get Info window you will see Capacity and Available. Make sure there's a minimum of 15% free disk space.

MacBook pro will not boot. I get the gray screen, an apple icon and spinning wheel. Tried to start in safe mode but get the same screen. The only thing different was that I loaded the zedge sync app yesterday. Now getting this problem.

Macbook pro will not boot. I get the gray screen, an apple icon and spinning wheel. I tried to start in safe mode, but get this same screen. The only thing different is that I added the zedge update app to do a sync for adding ringtones to my apple cell phone. How can I get a good boot. I am fairly new to apple computer.

Reset PRAM: http://support.apple.com/kb/PH4405 and then try a normal boot.
Run the Startup Manager to select Startup disk: http://support.apple.com/kb/HT1310
If those did not work your disk may be sick or dying. The top priority at this point is to make a backup copy of your data.
Check the health of the disk. Boot in Recovery Mode (Boot, Command-R). Run Disk Utility. Click on the upper left disk icon. Does the S.M.A.R.T. status say “Verified”? If not the disk/SSD is unhealthy and needs to be replaced. Even if it does not show “Verified” you can still attempt a backup.
Click on the icon indented below, usually called “Macintosh HD” and Verify Disk. If it finishes with a green “OK” message then all is well with the disk. If it shows errors in red then you have found a problem to address once the system is backed up. Do not attempt software repairs until you have secured the data.
If the disk will not show up at all in Disk Utility as your ran the tests above then it may be dead or it may have a bad internal SATA cable. A trip to an Apple store for confirmation would be in order.
If you have an external disk drive you can use as a backup drive then do so. If not Google “Hitachi USB 3.0 external hard drive 1TB” to purchase one or go to a brick-and-mortar store (including an Apple store) to pickup one. Any 1 TB external drive will do.
Assuming it is still breathing you can try to recover the data without booting from the sick disk.
Reformat the external disk. (This will erase all data on the external disk.)
Boot in Recovery Mode. Start Disk Utility. Plug in the new disk. Select it’s disk Icon (the second one down, left justified). Select the Partition tab.
Partition Layout > Single Partition
Name: Emergency Recovery 1 (or whatever name you wish to use)
Format: Mac OS Extended (journaled)
Options… > GUID Partition Table > OK
Apply
Select the Restore tab.
Drag the old system volume (Macintosh HD) to Source.
Drag the new disk volume (Emergency Recovery 1) to Destination.
Click on Restore.
It may take a long time for the backup.
If that will not complete post back for other emergency data recovery methods, including those from a brody.
If the backup succeeds, use the First Aid tab in Disk Utility to select the old volume (Macintosh HD) and Repair Disk. If it does not finish with a green OK message try to repair it once or twice more. If it repairs with a green OK message, will it boot normally? If not, boot from the Recovery Partition and reinstall OS X.
If it is still not healthy, post back for further instructions.

Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?

Similar Messages

Maybe you are looking for