MacBook pro showing message as ntldr missing

Unable to login to lapi .... It's gives me message stating NTLDR is missing... Kindly help

Yeah your Windows Boot Camp partition is FUBAR.
As above post suggests. Do a hard OFF, hold down the power button until the system turns off. Then hit the power button one more time and hold down the Options key. This will give a screen to select the drive to boot off of. Select Macindosh Hard Drive.

Similar Messages

My macbook pro shows blank screen when I started..help me..

My macbook pro shows blank screen when I started . (It's like in same state when power off. ) fan sound and hard disk is running. So i connected it Through external monitor via mini display to VGA cable. I can see everything on external monitor. My display of Mac needs to change? How much it cost ?? I found so many forum discussion said that if nvedia card is faulty then its happen...let me know suggestions...I given it to apple care service station n they r telling yr display needs to change its cost me a lot.. I can't afford. And can't spend that much for 3 yr old version as new versions of macbook pro is cost vice reasonable.. can I have any suggestion?

If running 10.7 or later hold down Command-R at Startup.
This should invoke recovery Mode.
Choose Disk Utility.
Select your Hard drive. Inspect the SMART Status in the lower right of the window for "Verified".
Select the Mac OS X Volume (originally Macintosh HD) click (Repair Disk)
If errors, run again until it comes clean or gets stuck.
Report any error messages.

My Macbook Pro Showing White Screen At startup

Macbook pro showing white screen after loading window
i think its not booting to hdd
What shoud i do??
Message was edited by: Krishnaraj7777

Krishnaraj7777,
you can try this: boot your MacBook Pro into Recovery mode by holding down a Command key and the R key as it starts up. Once the OS X Utilities menu appears, select Disk Utility. On the left-hand side of the Disk Utility window, select your internal disk’s boot partition (typically called “Macintosh HD”). On the right-hand side, press the Verify Disk button if it’s not greyed out; if it is greyed out, or if it reports that errors were found, press the Repair Disk button. Once the verification/repair is completed, exit Disk Utility and select Restart from the Apple menu to restart in normal mode. Do you get past the white screen now?

IMessage on MacBook Pro shows i'm my friend. My friend's photo and name shows in every conversation instead of mine. How do I fix this?

iMessage on MacBook Pro shows i'm my friend. My friend's photo and name shows in every conversation instead of mine. How do I fix this?

I am using my own Apple ID. (My father doesn't even have one). I seem to recall having to select a contact or something to assign to my iMessage app when I used it the first time on my iPad. I checked the settings and it is set to my apple ID and correct email address. Any other ideas?

MacBook Pro 13" Early 2011 - Airport missing SSID

after instal mac os x mountain lion MacBook Pro 13" Early 2011 Airport missing ssid and the chanel from 1 to 11 is missing too i live in syria and all the router wifi in the market have 1 to 11 chanels, what can i do i can't see any available
en1:
Card Type:          AirPort Extreme (0x14E4, 0xD6)
Firmware Version:          Broadcom BCM43xx 1.0 (5.106.98.81.20)
MAC Address:          e0:f8:47:21:65:4e
Locale:          FCC
Country Code:          SY
Supported PHY Modes:          802.11 a/b/g
Supported Channels:          36, 40, 44, 48, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
Wake On Wireless:          Supported
AirDrop:          Supported
Status:          Not Associated
please help me i can't connect to any network because i cant't see any of those

sure, i try everything even format my mac more than 5 times and the last i try to install windows 7 and i don't have this poblem, but don't like windows so i reinstall ML and now i have same the problem
please help me

I have iWork 09 with a family license. I am unable to install the software on my new Macbook Pro (the message is simply "Installation failed"). I wonder if I need to remove an old computer from the family license, and if so, how?

I have iWork 09 with a family license. I am unable to install the software on my new Macbook Pro (the message is simply "Installation failed"). I wonder if I need to remove an old computer from the family license, and if so, how?

Yes, gladly. I am trying to install on a 13" MacBook Pro with OS X 10.8.3. I insert the disk into the SuperDrive. The I work '09 window pops up with two icons: one Tim install and one that says "Read before you install iWork." I double-click on the "Install iWork '09" icon, and a window appears that says, "This package will run a program to determine if the software can be installed." I click "continue" and see "Welcome to the iWork '09 installer." I click on "Continue." The "read me" bullet on the left lights up, and I see "Read before you install. . . ." I click "Continue," then see the software license agreement. When I click on "Continue" again, I am asked to agree, and I do. The window then says, "Standard Install on 'Mackintosh HD" and indicates how much space the program will take.
I click "Install," enter my password, and the installation begins. It goes through a validating phase and begins "writing files." It indicates that installation will take about 30 minutes (although that number fluctuates). After about four minutes it goes to "cleaning up." Then after just a few seconds, the "Summary" bullet on the left lights up and this message appears: "There were errors with the installation. You may want to try installing again." There is a large yellow triangle with an exclamation point in it, and a bold "The installation failed." Below that appears "The installer encountered an error that caused the installation to fail. Contact the software manufacturer for assistance."
At that point, a "Close" button is pulsating blue at the bottom of the window.
Sorry for the tedious detail. Anything revealing there?
Thanks!

My MacBook Pro shows the logo in a white screen when I ask for a Software Update under the apple. Actually it stays blank on Featured, Top Charts, Categories and Purchases as well. What up? Thanks.

My MacBook Pro shows the logo in a white screen when I ask for a Software Update under the apple. Actually it stays blank on Featured, Top Charts, Categories and Purchases as well. What up? Thanks.

I am having exactly the same problem right now. After some research, it looked like my HD was toast. I replaced it today, that part was easy, but now I cannot seem to use my original Install Disk to format the new HD. I get a grey restart screen, or if I get to the Language Selection screen, my cursor is frozen in left corner and I can't use it.
Very frustrating, hope someone else has some ideas!
PS My MacBook was about same age, and "expired" in exactly the same way as yours.

MacBook Pro shows 356gb of App Storage

My MacBook Pro shows 356gb used for apps but when I click Get Info for the Applications folder it only shows 9gb used.
9gb to 356gb is a significant jump.. Is there any way I could delete this or find the 300gb+ excess of storage is?

Probably you do not have 356 GB of apps on your computer, so you can try reindexing your hard drive. Follow the steps given in this Apple support article to do so -> Spotlight: How to re-index folders or volumes - Apple Support (you have to reindex "Macintosh HD").

Some photos in iPhotos on MacBook Pro show "!" Do I have too many photos?

Some photos in iPhotos on MacBook Pro show "!" There are 7000 photos.
Do I have too many photos and have to delete some?

rabrab@ozemail wrote:
There are 7000 photos.
Do I have too many photos and have to delete some?
No.
Have a current backup.
Hold the option command keys and launch iPhoto to launch the First aid.
Start with repairing permissions first and proceed from there.
If you need to be more agressive, try the tried and true:
http://www.fatcatsoftware.com/iplm/

When i try to install a program in my macbook Pro, the message appear: Run preflight scrip and after Run the postflight script. How i'll fix this?

When i try to install a program in my macbook Pro, the message appear: Run preflight scrip and after Run the postflight script. How i'll fix this?

Here are the Mac requirements:
System Requirements Mac Version (*)
Mac OS X 10.6.1, 10.7.1, 10.8.1 or 10.9.1
1.83 GHz cpu or better
Nvidia Geforce 8600, ATI Radeon X1600 or better (min 256 MB VRAM)
1 GB RAM
2 GB free hard drive space
DVD-ROM Drive
Are you sure that you have the Mac version, as there is a Windows version, as well as a few game console versions.
Sounds as though that may be a Windows or other version.

My MacBook Pro shows a grey screen at start-up how do I fix this problem?

My MacBook Pro shows a grey screen when I try to login and won't go onto my homepage. Why has this happened and how do I fix it?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

How do i sync my contacts from my iPhone with my macbook pro for messaging purposes?

How do i sync my contacts from my iPhone with my macbook pro for messaging purposes?

Hey dthompson2108,
Thanks for participating in the Apple Support Communities.
You can sync contacts between your iPhone and MacBook Pro using iCloud or iTunes.
See this link for help with setting up iCloud on your computer and device(s):
Apple - iCloud - Learn how to set up iCloud on all your devices.
Instead of turning on iCloud on your iPhone and Mac, you can sync using iTunes as explained in this article:
Sync your iPhone, iPad, and iPod with iTunes using USB - Apple Support
All the best,
Jeremy

My MacBook Pro showed Spinning weel (SPOD) and when I tried to reboot took ages to restart (20 minutes)now shows SPOD after every command and is extrmely slow

My MacBook Pro showed Spinning weel (SPOD) and when I tried to reboot took ages to restart (20 minutes)now shows SPOD after every command and is extrmely slow

See if you can download and post an Etrecheck report:
http://www.etresoft.com/etrecheck
Ciao.

My Macbook Pro shows the apple and spinning wheel at start up but won't continue startup. Any Help would be appreciated.

My Macbook Pro shows the Apple and spinning wheel at startup but will not continue the startup. Does anybody know how to get past this, so the computer continues to startup?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. The easiest way to deal with the problem is to boot from an external drive, or else to use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 9
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Repeat Step 9, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

My MacBook Pro shows the "Macintosh HD" icon on the desktop but my MacBook Air does NOT have the icon on it's desktop. Is this normal? If not, how do I remount the MacBook Air disk icon on the desktop?

My MacBook Pro shows the "Macintosh HD" icon on the desktop but my MacBook Air does NOT show the icon on it's desktop. Is this normal? If not, how do I remount the MacBook Air "Macintosh HD" icon on it's desktop?

Is it showing in the Finder?
If so, then this is normal.
Cheers,
GB

MacBook pro showing message as ntldr missing

Similar Messages

Maybe you are looking for