Mainboard did not detect SATA1 HDD

My PC using P965 Platinum Series MS-7238 motherboard, Processor Intel Dual Core 3.0 GHz, 128MB Nvidia G-Force PCI VGA, RAM 1024MB Visipro, HDD 80GB Seagate barracuda 7200rpm SATA1, and I have bought it on 2nd of June 2007. during these periode of time (the date I bought till last week) my PC running well.
Last week 21st of may 2009, I found my PC did not detect my HDD. I have installed the HDD to another PC in order to check whether the problem was caused by my HDD or the motherboard. After I tested the HDD by installing it to another PC, it seems the HDD is in good condition and running well.
After that I try to change the powerd cord and SATA1 cord to the HDD with the brand new one to check if the problem caused by the cords and still my motherboard did not detect the HDD. I am very confused what is wrong with my PC. Please help me to solve this problem so that I can use my PC back.

Hi,
the board has two controllers (ICH8R Primary SATA Controller (SATA Ports 1-6)) and JMicron JMB361 (SATA Port 7)). Which SATA Port is your hard drive connected to? The chance that both onboard SATA Controllers or all SATA Ports have been damaged is very low. Try other SATA ports and see if the situation changes if you connect it to a different controller.
Also, have you cleared CMOS with main A/C power cable removed from PSU to see if that changes anything?

Similar Messages

MSI x48c platinum - does not detect SATA HDDs

I am having some problems with a pc build with motherboard not detecting SATA HDDs (MIS x48c Platinum).
I believe I have exhausted all other avenues, and I would appreciate some help if I have missed something obvious.
(details of other components are listed at end of mail).
When I built pc using these components, and went into BIOS settings, the SATA HDD's were not detected. I tried changing BIOS settings, but no difference if SATA, AHCI, or IDE settings.
I removed the HDDs and successfully tested them in another machine (also formatted them while had them istalled in other pc).
IDE optial drives are detected. I have tried to boot with these disconnected to ensure no isues with both IDE and SATA drives connected, but this did not resolve issues.
I have also tried connecting HDD to different onboard SATA ports, and connecting just one drive with no success.
Resetting BIOS defaults, and using clear CMOS reset did not resolve issues either.
Sometimes on boot, it takes a few attempts to boot correctly, and on these occassions I receive an error message "Warning !!! The previous performance of overclocking is failed, and the system is restored to the default settings, Press any key except "DEL" to enter setup ......." I haven't tried to set any over clocking.
I read about a number of issues on MSI forum related to SATA drives which were resolved by BIOS upgrade (mobo was shipped with v.7.0 released 20 March 08). I managed to install an old IDE HDD and flash BIOS, but still no resolution of issues detecting SATA drives (BIOS V.7.2 released 29 July 08).
I've tried everything I can think of at this stage. Is there anything else I should try, or is there something wrong with this motherboard?
Spec:
Motherboard:
343949 MSI X48C Platinum, X48, Socket-775,
DDR2/DDR3, ATX, GbLAN, 2xPCI-Ex(2.0)x1
Other components in build:
CPU Intel Core 2 Quad Q9550
Graphics Sapphire Radeon HD 4870 512MB
HDD 2 x Samsung SpinPoint T166 500GB
RAM 4GB (2x2GB) GeIL DDR3 1333MHz Value Dual Channel (7-7-7-24) PC3-10660
PSU 700W X-Power ATX SLI PSU
ODD DVD & CDR drives from an old pc - IDE connections.

i just remember i had once similar problem with a sata driver. the issue is this you can not adjust everything in bios in one go and expect mobo to know about it. what i mean is this for instance you disable the raid then you save it and exit and then when it reboot you go back to bios and reset another another parameter, you save and exit and on reboot you go back to bios and reset another parameter. i got round the prob that way and it worked and mobo saw the sata HDD. give this a shoot good luck and finally make sure raid is disabled
this is what i would do
1- make sure the jumper setting on your IDE Hdd is correct (Y may have to try this twice as there are two different setting on jumper setting for Master)
2- connect the sata HDD
3-click on power
4-go to bios and disable raid save exit
5-on reboot go back to bios
6--on first option click on it then you should see all devices that can be seen by mobo if you do not see sata HDD you have to click on enable for the auto to see the device once it sees the device save and exit. REMEMBER THE JUMPER SETTING ON IDE HDD CAN CAUSE PROB . SO try the other jumper setting for master, repeat this procedure once more hopefully you get it right

Windows did not detect any networking hardware, Windows 7, New Hard Drive

Message "Windows did not detect any networking hardware"
Satellite P505 S8980 Windows 7 Home Premium.
I replaced the Toshiba 500 GB HD with 500 GB Seagate.
Device Manager icon for any device with yellow exclamation mark,
Click on "Update Driver". Lan eNet details as follows:
Antheo - R8132 PCI-E Fast Ethernet Controller (NDIS 6.20)
Browse to the folder where the setup program has the driver...
Message: "The best driver software is already installed."
(But the yellow exclamation mark still harasses me.)
--- Go to "Setup new connection" ---
"Choose a connection option"
Click on "Connect to the Internet"
Response: "Windows did not detect networking hardware"
As near as I can tell, that translates from error 0x8E5E0247
I have this same error on other yellow exclamation marks respective of what kind of device it is.
=> To test my sanity, I put the old hard drive (same size) back in and except for the impact of slowness due to error retries, everything works okay.
Note:
Same issue (hardware not detected) for Video adapter and Audio.
I bought new USB Wireless adapter to test, and the driver installed but not activated because "not digitally signed", and that same issue fits all the above hardware. I down loaded them from Toshiba, and they are confirmed installed, but not accepted with digitally signed. I have uninstalled and reinstalled with same results.
Solved!
Go to Solution.

I'm discovering I am not as well as I thought... running on the AF hard drive which was built with a copy drive from old format drive which was the product of system recovery disc set.
Review for context: Advanced Function HDD
Scenario that exposes harm caused by cloning data from 4K blocks drive to 512 bytes blocked drive (AF)
Toshiba supplied Windows-7 System Restore Discs: to factory state
Then I built the Windows-7 Repair Disc... used later.
Hard drive was replaced when it caused SMART warning at every system boot.
Acronis was only utility that quickly detected problem (3 sectors had permanent read errors.) Active@Disk Image and Power Quest Drive Image (Ghost) did not detect the issue.
I tried Seagate 500 GB and Western digital 500 GB HDD drives as copy target.
That new drive would not boot: "Required source not found"
Booted My newly created Windows-7 repair disc, and used to to fix startup.
See images.
That worked and then the ST9500423AS disc booted.
Now... next day I discovered Window Update is not working.
I get message:
Windows Update cannot currently check for updates, because the service is not running. You need to restart your computer.
I ran Microsoft Fixit for updates. It says it fixed two items.
I still have the problem.
The service shows "started"
Control Panel/ ACTION Center/ Maintenance/ Check for Updates
"No action needed"
"Windows Update does not require any action"
I checked Update History...
... It is empty, else window is vacant... blank.
Soooo..... for a sanity check, I swap out hard drive; go back to the old format (which is the one I copied).
It works! 7 updates to install, including SP1... but I did NOT install them.
Switch back to the AF drive... Update doesn't work. I am broke again.
Is this another strange problem caused by the Advance Format issue?
What to do?
By the way... I did install an Intel storage Matrix driver update, but I do not have RAID chip, so that driver is not for me... unless I missed out on something.
Carl

Surface Pro 3 / "Windows did not detect a properly installed network adapter"

Hi all,
I've been running the Windows 10 Technical Preview (9926) on my Surface Pro 3 successfully
since January. Unfortunately, I lost all internet connectivity today.
The problem started when I noticed the type cover wasn't working (pressing keys on the type
cover wasn't registering any typing on my screen) and my USB mouse wasn't working either. I tried removing and reattaching the type keyboard but this didn't fix the issue. I had to use the accessibility on-screen keyboard to sign into Windows (thankfully touch
was still working). Once I signed in, I still didn't have typing or cursor ability, so I decided to restart the computer.
Then it got worse. I noticed the Surface Pro 3 was stuck on "restarting" and wouldn't
actually restart. Since it wasn't responding, I held down the power button for about 10 seconds until it turned off. When I turned it back on, the type cover and mouse started working again.
Unfortunately, this is when the WIFI problems began. I had WIFI for a few seconds, and then
I lost internet. I disconnected/reconnected but there was a yellow triangle telling me there was some sort of problem. So I restarted the Surface Pro 3.
When it came back on, there were suddenly NO connections available at all. Opening the "Network
& Internet" settings page gave me the message "Windows did not detect a properly installed network adapter". And here I am, without internet on my Surface Pro 3, borrowing my friend's computer so I can type this message (he is also running
Windows 10 build 9926 on his laptop and is able to connect to my WIFI with no problems, whereas my Surface Pro 3 cannot even detect any networks). I have not dropped or damaged the SP3 in any way, and there have been no storms or power outages or anything
of that sort. Any ideas what could have happened to the WIFI on my Surface Pro 3?
Thanks for your help...
Ethan

Hi Ethan,
Currently, there are a few compatibility issue between the current hardware and Windows 10 Technical Preview (9926 build), this is mostly related to driver compatibility issue.
I suggest you download the latest network adapter driver package to install, when it is finished, check if it appears under Device Manager.
Surface Pro 3, Surface Pro 2, and Surface Pro firmware and driver packs
https://www.microsoft.com/surface/en-us/support/networking-and-connectivity/install-wireless-drivers
You can check if you can install the latest firmware package for your device.
Here is an article to talk about such things:
Windows 10 January Technical Preview on Surface
https://www.microsoft.com/surface/en-us/support/install-update-activate/windows-technical-preview#Known
Regards,
Alex Zhao
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Hi, I got a virus that does not let me use Safari. I downloaded an av from the app.store but it did not detect anything. I am thinking in formatting the HD. How can I do it and will I lose?

Hi, I got a virus that does not let me use Safari. I downloaded an av from the app.store but it did not detect anything. I am thinking in formatting the HD. How can I do it and will I lose?

1. Force Quit .
    Press command + option + esc keys together at the same time. Wait.
    When Force Quit window appears, select the Safari if not already.
    Press Force Quit button at the bottom of the window.   Wait.
    Safari will quit.
    Relaunch Safari holding the shift key down.
2. Safari > Preferences > Extensions
    Turn those off and try Safari.
3. Safari > Preferences > Privacy > Cookies and other website data:
    Press “Remove all website data” button.
4. If adware is installed without your knowledge,
    download free AdwareMedic by clicking “Download ” from here
    http://www.adwaremedic.com
   Install , open, and run it by clicking “Scan for Adware” button   to remove adware.
   Once done scanning and removing the adware, quit the app by clicking AdMedic in the menubar
    and selecting “Quit AdwareMedic”.

Wndows did not detect any biometric devices on this computer..

I have an HP ProBook 4540s running Windows 7 Professional w/IE11. I had to do a clean install of Windows 7 Pro and since then I cannot get my fingerprint reader to work at all. In my Control panel, under Biometric Devices, I recieve the message "Windows did not detect any biometrics devices on this computer". However, under Computer , Properties, Device Manager, Biometric Devices, the is Validity Sensors (WBF) (PID=003d).
I have tried to update, uninstall, re-install HP Simplepass, drivers, etc from the HP website, but nothing is working. Also I cannot find exactly what fingerpriint reader hardware is installed on the computer even though it is physically there as part of the original configuration.
I appreciate any assistance in resolving this issue.
Mark

Hello Mark531,
Welcome at the HP forums,
Are you searching for the following driver?
http://ftp.hp.com/pub/softpaq/sp64001-64500/sp64338.exe
Winos.
The doors of wisdom are never shut. Benjamin Franklin
We must use time wisely and forever realize that the time is always ripe to do right. Nelson Mandela

Windows did not detect any networking hardware iMac 27' 2013 model

Installed windows 7 using bootcamp now when I go to connect to a network it says windows did not detect any networking hardware

Did you install the windows drivers as well?

I just tranfer all my photo from my Mac though itune to my iPhone so I can setup Mac back to factory setting after doing I try to put my photo vac to my Mac I photo did not detect any of the photo that I had tranfer from itune it only detectPLAESE HELP!

I just tranfer all my photo from my Mac from itune to my Iphone so I can setup Mac back to factory setting after I don't with that, I try to put my photo back to my Mac and Iphoto did not detect any of the photo that I had tranfer from itune it only detect the one rhat i took with the Iphone PLAESE HELP!!!!!!

Hello Partii,
It sounds like you may use a POP account for your email. With a POP account, email applications like Mail and Outlook can remove emails from the server, so when another device tries to check the server for new emails, it doesn't see any.
You may need to adjust settings in Outlook so that the emails are not removed from the server when downloaded. I found an article with more information:
When using a POP email account with multiple devices, email messages may only appear on the first device that receives them. This occurs when an email client is configured to automatically remove email from the server once an email client has received it. You can configure your email client (or clients) either to keep a copy of the email on the server, remove it after a certain number of days have passed, or keep it until you move it from your Inbox.
I recommend reviewing the full article for steps on adjusting these settings; you can find the full article here:
Using a POP account with multiple devices
http://support.apple.com/kb/HT3228
Thank you for using Apple Support Communities.
Best,
Sheila M.

M2N78-LA Motherboard BIOS did not detect any Hard Drive

Hi,
I have M2N78-LA Motherboard and the BIOS did not detect ANY hard drive
I tried
1- Replaced the HD with another one. did not work
2- Changed the jumper of HD. did not work
3- Changed the SATA data cable and power cable. did not work.
4- Reset the BIOS by removing the battery and also by positioning the cmos jumber. did not work.
I still all time get no hard drive detected, and some time jam on Detecting storage devices ....
then after hours get no booting device.
Any Idea will be good

M2N78-LA Motherboard BIOS did not detect any Hard Drive, does anyone have an answer to this problem.

Bluetooth did not detect any Bluetooth device even iPhone please help me

I have iPhone 4 my Bluetooth did not detect any Bluetooth
Device even iPhone so I can not transfer any data to other iPhone
Please help me

That is correct.
This has never been a feature of iphone.
Sorry.
Bluetooth is supported for stereo headsets/speakers, telephone headsets/handsfree devices, some keyboards, some peer-to-peer apps from the apps store, tethering where provided by the carrier.
Other than these, it will not connect to another phone/device/computer/etc.

"Setup did not detect the required components. Setup will exit." !?!?!?

I have a retail Audigy 2. Autoupdate recognizes my card and gives me the available list of drivers and applications for download. I download the following:
) Audigy 2 Drivers
2) Audio Console
3) EAX Console
4) Speaker Settings
5) Surround Mixer
The ) Drivers and the 2) Audio console installs just fine. However, for each of the three remaining programs (3, 4, & 5 listed above) upon executing the downloaded file they all give me a pop-up window that says:
?Setup did not detect the required components. Setup will exit.
This happens with all three of them. I want to install these because I am of the understanding that one of these contains the ?Speaker channel test? (for lack of a better word) that will test if my speakers are hooked up correctly to the right channels. The ) drivers, and 2) Audio console do not have that test. I created another post concerning this but nobody has replied:
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=39825
I also tried unzipping the three executable files with WinRAR, and then executing the Setup.exe files but it yields the same results.
Anyone know why I can't install these applications?!?!?!?!
I swear, I have never had so many problems with a particular brand of product than I have with Creative products?.yet I keep buying them anyway?.sheesh?.Message Edited by Bridgeboy on -30-2005 05:0 PM

nanite2000 wrote:
superidan wrote:
I have retail Audigy 2 card. tryed removing the card and installing on a differant slot. Nothing Works! it produces the same "no audigy 2 card found - setuip will now exit" Creative sould be ashamed thanks
Yes, Creative should be ashamed.
This is a known problem that has been around for months and they have failed to address, just like many other problems with their soundcards. For the solution to this particular problem, look here:
http://forums.creative.com/creativel....id=3964#M3964
If you would reread my original post in this thread, that solution did not work for this particular problem of mine. I have a SoundBlaster Li've! Card that this solution worked for, however it does not work of the Audigy 2 card?unzipping the files with WinRar and then running the Setup.exe files produces the same result?setup does not recognize the required components and will close.
I?m not saying that the person who you quoted should not try it though.

Wich drivers to install after ´Windows did not detect any networking hardware´

Hi there, I just reinstalled my laptop. But something went wrong. My laptop says now:Windows did not detect any networking hardware´ I found already out that I need to install drivers. But there is so much choice. Wich one do I need to install.http://h20566.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=5405166&swLangOid=8&swEnvOid=4059 Hope you can help me!Freek

Hi @sweetandsouther ,
Welcome to the HP Forums!
It is a terrific place to find answers and suggestions!
For you to have the best experience in the HP forum I would like to direct your attention to the HP Forums Guide Learn How to Post and More
How Do I Find My Model Number or Product Number?
I understand that Windows it not detecting any network hardware.
If you check Device Manager is it recognized?
If the card is listed is there an error on it?
If not and you are out of warranty you could try reseating the network card.
Here is a link HP Notebook PCs - Testing for Hardware Failures (Windows 7, Vista) to that may also help.
Here is a link to HP PCs - Troubleshooting your wireless network and Internet connection (Windows 7) that may also help.
Have you ran the HP Support Assistant ?
Have you tried using MS Fix It?
You may choose to contact HP support for assistance with this difficulty.
Please call our technical support at 800 474 6836. If you live outside the US/Canada Region, please click the link below to get a support number for your region.
World Wide Phone Support
Good Luck!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

EAX console woes: did not detect required components/audigy2 not detec

After a recent reformat, I go to install the EAX console after the latest drivers (don't have my original CD by the way) aaaand get the "did not detect required components" message.
So I search on it and it doesn't have anything to do with my dri've paths and such. I've tried an Audigy2 and Audigy2 value ISO, but they tell me they don't detect an audigy2... dxdiag tells me differently, however. I'm not in the mood for downloading a bunch more 400 mb ISOs to test them all out either..
I'm at a loss here and really need the EAX console... autoupdate detects my card as "Sound Blaster Audigy 2, DR release .88.20"

nanite2000 wrote:
superidan wrote:
I have retail Audigy 2 card. tryed removing the card and installing on a differant slot. Nothing Works! it produces the same "no audigy 2 card found - setuip will now exit" Creative sould be ashamed thanks
Yes, Creative should be ashamed.
This is a known problem that has been around for months and they have failed to address, just like many other problems with their soundcards. For the solution to this particular problem, look here:
http://forums.creative.com/creativel....id=3964#M3964
If you would reread my original post in this thread, that solution did not work for this particular problem of mine. I have a SoundBlaster Li've! Card that this solution worked for, however it does not work of the Audigy 2 card?unzipping the files with WinRar and then running the Setup.exe files produces the same result?setup does not recognize the required components and will close.
I?m not saying that the person who you quoted should not try it though.

Here, ipod touch screen went white, tried to plug it in to itunes, computer did not detect it. Tried pressing the menu and off/on button for 10 seconds and it still didn;t work? Help please.

Hi there, ipod touch went white. I tried the menu and on/off button for 10 seconds. I also tried connecting to the computer via i tunes. My computer did not detect the ipod? Any other options?

See the white-screen topic of:
iPod touch: Hardware troubleshooting

IPhone 4 with IOS 6 did not detecting the public wi-fi network but able to connect with my home wireless

iphone 4 after install the iOS 6 wi-fi networks are not detecting on public spot but working on home network.What is the reason for this/ any settings?

Is the firmware in the router up to date?
See here for the latest for v2.2: http://homesupport.cisco.com/en-us/support/routers/WRT54G
Note: All these ideas are a bit lame since you say that some iPhone 5s are connecting OK and they running the same iOS level 6.1 and, i think, have the same Broadcom WiFi chip BCM4334.
All devices are running iOS 6.1 right not 6.0.1, or 6.0.2?
You might want to try your iPad mini on some other WiFi networks to see how it fares there.

Mainboard did not detect SATA1 HDD

Similar Messages

Maybe you are looking for